Gonna be covered later with further PRs. Now adding them to avoid compiler
errors due to uncovered switch/cases.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
We have dynamic capability support, but it handles only MP capability.
With this change, we can enable software version capability dynamicaly, without
resetting the session.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Add a `--v6-with-v4-nexthop` cli to bgp to allow it to peer with
neighbors in the configuration where the interface has no v6 addresses
at all and there is a v4 address that is usable as a v4 address
embedded in a v6 address.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Modify bgp to not allow a v6 peer to come up if the v6 afi is negotiated
and the outgoing interface has no v6 address as well as zebra does
not support the v6 with v4 nexthop capabilities that some dataplanes
allow.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
RCA:
On encountering any attribute error for core attributes in update message,
the error handling is set to 'treat as withdraw' and
further parsing of the remaining attributes is skipped.
But the stream pointer is not being correctly adjusted to
point to the next NLRI field skipping the rest of the attributes.
This leads to incorrect parsing of the NLRI field,
which causes BGP session to reset.
Fix:
The stream pointer offset is rightly adjusted to point to the NLRI field correctly
when the malformed attribute is encountered and remaining attribute parsing is skipped.
Signed-off-by: Samanvitha B Bhargav <bsamanvitha@vmware.com>
When 'no neighbor .. update-source' is issued for a regular peer, that
peer is always reset. This is unnecessary if the peer is a member of a
peer-group and it inherits an identical update-source, so let's skip
the reset/Notification for that condition.
Config:
------------
router bgp 1
neighbor PG peer-group
neighbor PG remote-as internal
neighbor PG update-source 100.64.0.3
neighbor 192.168.122.99 peer-group PG
neighbor 192.168.122.99 update-source 100.64.0.3
Before:
------------
ub20-2(config-router)# do show ip bgp sum | include .99
192.168.122.99 4 1 36 34 0 0 0 00:00:17 0 0 N/A
ub20-2(config-router)# do show ip bgp neighbors 192.168.122.99 | include Local host
Local host: 100.64.0.3, Local port: 46083
ub20-2(config-router)# no neighbor 192.168.122.99 update-source
ub20-2(config-router)# do show ip bgp sum | include .99
192.168.122.99 4 1 36 35 0 0 0 00:00:01 Idle 0 N/A
ub20-2(config-router)# do show ip bgp neighbors 192.168.122.99 | include Local host
Local host: 100.64.0.3, Local port: 39847
After:
------------
ub20-2(config-router)# do show ip bgp sum | include .99
192.168.122.99 4 1 3 3 0 0 0 00:00:20 0 0 N/A
ub20-2(config-router)# do show ip bgp neighbors 192.168.122.99 | include Local host
Local host: 100.64.0.3, Local port: 39415
ub20-2(config-router)# no neighbor 192.168.122.99 update-source
ub20-2(config-router)# do show ip bgp sum | include .99
192.168.122.99 4 1 3 3 0 0 0 00:00:28 0 0 N/A
ub20-2(config-router)# do show ip bgp neighbors 192.168.122.99 | include Local host
Local host: 100.64.0.3, Local port: 39415
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
The last_reset_cause is a plain old BGP_MAX_PACKET_SIZE buffer
that is really enlarging the peer data structure. Let's just
copy the stream that failed and only allocate how ever much
the packet size actually was. While it's likely that we have
a reset reason, the packet typically is not going to be 65k
in size. Let's save space.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Currently, json output of show BGP commands are no pretty format.
This is an extremely expensive operation for huge scale (lots of
routes with lots of paths).
BGP json non-pretty commands support added:
```
show bgp neighbors <nbr-id> advertised-routes json
show bgp neighbors <nbr-id> received-routes json
show bgp neighbors <nbr-id> advertised-routes detail json
show bgp neighbors <nbr-id> received-routes detail json
```
Ticket:#3513256
Issue:3513256
Testing: UT done
Signed-off-by: Sindhu Parvathi Gopinathan's <sgopinathan@nvidia.com>
The ringbuf is 650k in size. This is obscenely large and
in practical experimentation FRR never even approaches
that size at all. Let's reduce this to 1.5 max packet sizes.
If a BGP_MAX_PACKET_SIZE packet is ever received having a bit
of extra space ensures that we can read at least 1 packet.
This also will significantly reduce memory usage when the
operator has a lot of peers.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Commit: a0b937de42
Introduced the idea of a input Q packet limit. Say you read in
635000 bytes of data and the input Q is already at it's limit
(currently 1000) then when bgp_process_reads runs it will
assert because there is less then a BGP_MAX_PACKET_SIZE in ibuf_work.
Don't assert as that it's irrelevant. Even if we can't read a full packet
in let's let the whole system keep working as that as the input Q length
comes down we will start pulling down the ibuf_work and it will be ok.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The peer->ibuf_scratch was allocating 65535 * 10 bytes
for scratch space to hold data incoming from a read
from a peer. When you have 4k peers this is 262,1400,000
or 262 mb of data. Which is crazy large. Especially
since the i/o pthread is reading per peer without
any chance of having the data interfere with other reads.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Over time the bgp_zebra_announce_default function has gotten
slightly convoluted, clean it up so it's easier to read
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
bgpd, pbrd: use common pbr encoder
zebra: use common pbr decoder
tests: pbr_topo1: check more filter fields
Purpose:
1. Reduce likelihood of zapi format mismatches when adding
PBR fields due to multiple parallel encoder implementations
2. Encourage common PBR structure usage among various daemons
3. Reduce coding errors via explicit per-field enable flags
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
Subset: ZAPI changes to send the new data
Also adds filter_bm field; currently for PBR_FILTER_PCP, but in the
future to be used for all of the filter fields.
Changes by:
Josh Werner <joshuawerner@mitre.org>
Eli Baum <ebaum@mitre.org>
G. Paul Ziemba <paulz@labn.net>
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
A route-map applied on incoming BGP updates is not able
to exclude the unwanted as segments, based on an AS path
access-list.
The below configuration illustrates the case:
router bgp 65001
address-family ipv4 unicast
neighbor 192.168.1.2 route-map rule_2 in
exit-address-family
bgp as-path access-list RULE permit ^65
route-map rule_2 permit 10
set as-path exclude as-path-access-list RULE
```
BGP routing table entry for 10.10.10.10/32, version 13
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
192.168.10.65
65000 1 2 3 123
192.168.10.65 from 192.168.10.65 (10.10.10.11)
Origin IGP, metric 0, valid, external, best (First path received)
```
After:
```
do show ip bgp 10.10.10.10/32
BGP routing table entry for 10.10.10.10/32, version 15
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
192.168.10.65
2 3 123
192.168.10.65 from 192.168.10.65 (10.10.10.11)
Origin IGP, metric 0, valid, external, best (First path
received)
```
Signed-off-by: Francois Dumontet <francois.dumontet@6wind.com>
Assuming field 'ifindex_ipv6_ll' is not equal to field 'ifindex', then
nhop_found is just a garbage, let's avoid that.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When switching `router bgp`, `no router bgp` and doing redistributions, we should
ignore this action, otherwise memory leak happens:
```
Indirect leak of 400 byte(s) in 2 object(s) allocated from:
0 0x7f81b36b3a06 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cc:153
1 0x7f81b327bd2e in qcalloc lib/memory.c:105
2 0x55f301d28628 in bgp_node_create bgpd/bgp_table.c:92
3 0x7f81b3309d0b in route_node_new lib/table.c:52
4 0x7f81b3309d0b in route_node_set lib/table.c:61
5 0x7f81b330be0a in route_node_get lib/table.c:319
6 0x55f301ce89df in bgp_redistribute_add bgpd/bgp_route.c:8907
7 0x55f301dac182 in zebra_read_route bgpd/bgp_zebra.c:593
8 0x7f81b334dcd7 in zclient_read lib/zclient.c:4179
9 0x7f81b331d702 in event_call lib/event.c:1995
10 0x7f81b325d597 in frr_run lib/libfrr.c:1213
11 0x55f301b94b12 in main bgpd/bgp_main.c:505
12 0x7f81b2b57082 in __libc_start_main ../csu/libc-start.c:308
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
problem:
In CLI config codeflow there are memory leaks in failure scenario
Fix:
Code changes are done to free ecommunity
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Useful to have it for datacenter profile only, disabled for traditional.
If the peer is not established or established, but has no description set,
we will show the FRR version instead, which is kinda handy to have instead of
nothing.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When running bgp_always_compare_med, I am frequently seeing a crash
After running with valgrind I am seeing this and a invalid write
immediately after this as well.
==311743== Invalid read of size 2
==311743== at 0x4992421: route_map_counter_decrement (routemap.c:3308)
==311743== by 0x35664D: peer_route_map_unset (bgpd.c:7259)
==311743== by 0x306546: peer_route_map_unset_vty (bgp_vty.c:8037)
==311743== by 0x3066AC: no_neighbor_route_map (bgp_vty.c:8081)
==311743== by 0x49078DE: cmd_execute_command_real (command.c:990)
==311743== by 0x4907A63: cmd_execute_command (command.c:1050)
==311743== by 0x490801F: cmd_execute (command.c:1217)
==311743== by 0x49C5535: vty_command (vty.c:551)
==311743== by 0x49C7459: vty_execute (vty.c:1314)
==311743== by 0x49C97D1: vtysh_read (vty.c:2223)
==311743== by 0x49BE5E2: event_call (event.c:1995)
==311743== by 0x494786C: frr_run (libfrr.c:1204)
==311743== by 0x1F7655: main (bgp_main.c:505)
==311743== Address 0x9ec2180 is 64 bytes inside a block of size 120 free'd
==311743== at 0x484B27F: free (in /usr/libexec/valgrind/vgpreload_memcheck-amd64-linux.so)
==311743== by 0x495A1BA: qfree (memory.c:130)
==311743== by 0x498D412: route_map_free_map (routemap.c:748)
==311743== by 0x498D176: route_map_add (routemap.c:672)
==311743== by 0x498D79B: route_map_get (routemap.c:857)
==311743== by 0x499C256: lib_route_map_create (routemap_northbound.c:102)
==311743== by 0x49702D8: nb_callback_create (northbound.c:1234)
==311743== by 0x497107F: nb_callback_configuration (northbound.c:1578)
==311743== by 0x4971693: nb_transaction_process (northbound.c:1709)
==311743== by 0x496FCF4: nb_candidate_commit_apply (northbound.c:1103)
==311743== by 0x496FE4E: nb_candidate_commit (northbound.c:1136)
==311743== by 0x497798F: nb_cli_classic_commit (northbound_cli.c:49)
==311743== by 0x4977B4F: nb_cli_pending_commit_check (northbound_cli.c:88)
==311743== by 0x49078C1: cmd_execute_command_real (command.c:987)
==311743== by 0x4907B44: cmd_execute_command (command.c:1068)
==311743== by 0x490801F: cmd_execute (command.c:1217)
==311743== by 0x49C5535: vty_command (vty.c:551)
==311743== by 0x49C7459: vty_execute (vty.c:1314)
==311743== by 0x49C97D1: vtysh_read (vty.c:2223)
==311743== by 0x49BE5E2: event_call (event.c:1995)
==311743== by 0x494786C: frr_run (libfrr.c:1204)
==311743== by 0x1F7655: main (bgp_main.c:505)
==311743== Block was alloc'd at
==311743== at 0x484DA83: calloc (in /usr/libexec/valgrind/vgpreload_memcheck-amd64-linux.so)
==311743== by 0x495A068: qcalloc (memory.c:105)
==311743== by 0x498D0C8: route_map_new (routemap.c:646)
==311743== by 0x498D128: route_map_add (routemap.c:658)
==311743== by 0x498D79B: route_map_get (routemap.c:857)
==311743== by 0x499C256: lib_route_map_create (routemap_northbound.c:102)
==311743== by 0x49702D8: nb_callback_create (northbound.c:1234)
==311743== by 0x497107F: nb_callback_configuration (northbound.c:1578)
==311743== by 0x4971693: nb_transaction_process (northbound.c:1709)
==311743== by 0x496FCF4: nb_candidate_commit_apply (northbound.c:1103)
==311743== by 0x496FE4E: nb_candidate_commit (northbound.c:1136)
==311743== by 0x497798F: nb_cli_classic_commit (northbound_cli.c:49)
==311743== by 0x4977B4F: nb_cli_pending_commit_check (northbound_cli.c:88)
==311743== by 0x49078C1: cmd_execute_command_real (command.c:987)
==311743== by 0x4907B44: cmd_execute_command (command.c:1068)
==311743== by 0x490801F: cmd_execute (command.c:1217)
==311743== by 0x49C5535: vty_command (vty.c:551)
==311743== by 0x49C7459: vty_execute (vty.c:1314)
==311743== by 0x49C97D1: vtysh_read (vty.c:2223)
==311743== by 0x49BE5E2: event_call (event.c:1995)
==311743== by 0x494786C: frr_run (libfrr.c:1204)
Effectively the route_map that is being stored has been freed already
but we have not cleaned up properly yet. Go through and clean the
code up by ensuring that the pointer actually exists instead of trusting
it does when doing the decrement operation.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
