afi_header_vty_out() is easily replaced with vty_frame(), which means we
can drop a whole batch of "int *write" args as well as the entirety of
bgp_config_write_family_header().
=> AFI/SAFI config writing is now a lot simpler.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
1. Change hostname_get to cmd_hostname_get
2. Change domainname_get to cmd_domainname_get
3. New API to set domainname
3. Provide a CLI command to set domainname
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Bug introduced by commit 37d361e7. Removing the call to bgp_close()
from bgp_delete() was a mistake.
Reported-by: Don Slice <dslice@cumulusnetworks.com>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When the underlying VRF is deleted, ensure that state for the
next hops that BGP registers with zebra for tracking purposes is
properly updated. Otherwise BGP will not re-register the next hop
when the VRF is re-created, resulting in the next hop staying
unresolved.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-17456
Reviewed By: CCR-6587
Testing Done: Manual, bgp-min, vrf
There are two parts to this commit:
1. create a database of self tunnel-ip for used in martian nexthop check
In a CLAG setup, the tunnel-ip (VNI UP) notification comes before the clag-anycast-ip comes up in the system.
This was causing our self next hop check to fail and we were instaling routes with martian nexthop in zebra.
We need to keep this info in a seperate database for all local tunnel-ip.
This database will be used in parallel with the self next hop database to martian nexthop checks.
2. When a local VNI comes up, update the tunnel-ip database and filter routes in the RD table if necessary
In case of EVPN we might receive routes from clag peer before the clag-anycast ip and VNI is up on the system.
We will store the routes in the RD table for later processing.
When VNI comes UP, we loop thorugh all the routes and install them in zebra if required.
However, we were missing the martian nexthop check in this code path.
From now onwards, when a VNI comes UP,
we will first update the tunnel-ip database
We then loop through all the routes in RD table and apply martian next hop filter if required.
Things not covered in this commit but are required:
This processing is needed in general when an address becomes a connected address.
We need to loop through all the routes in BGP and apply martian nexthop filter if necessary.
This will be taken care in a seperate bug
Ticket:CM-17271/CM-16911
Reviewed By: ccr-6542
Testing Done: Manual
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
When displaying the config, bgpd only checked for the existance of a peer-group prefix-list before
deciding to not display the outbound prefix-list. This commit updates the outbound prefix-list
logic to match the inbound.
afi_header_vty_out is sidestepping the vty code, writing straight to the
output (either stdout or the obuf), which results in newline translation
not being performed.
Easiest fix is replacing it with a macro. Longer-term, I have some old
code to add "prefaces" to the vty output, planning to dig that up.
Fixes: #949 ("bgpd show running doesn't show new lines")
Reported-by: Lou Berger <lberger@labn.net>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The defines:
ONE_DAY_SECOND
ONE_WEEK_SECOND
ONE_YEAR_SECOND
were being defined all over the system, move the
define to a central location.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
SAFI values have been a major source of confusion over the last few
years. That's because each SAFI needs to be represented in two different
ways:
* IANA's value used to send/receive packets over the network;
* Internal value used for array indexing.
In the second case, defining reserved values makes no sense because we
don't want to index SAFIs that simply don't exist. The sole purpose of
the internal SAFI values is to remove the gaps we have among the IANA
values, which would represent wasted memory in C arrays. With that said,
remove these reserved SAFIs to avoid further confusion in the future.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
swpX peers all start out with the same sockunion so initially they all
go into the same hash bucket. Once IPv6 ND has worked its magic they
will have different sockunions and will go in different buckets...life
is good.
Until then though, we are in a phase where all swpX peers have the same
socknunion. Once we have HASH_THRESHOLD (10) swpX peers and call
hash_get for a new swpX peer the hash code calls hash_expand(). This
happens because there are more than HASH_THRESHOLD entries in a single
bucket so the logic is "expand the hash to spread things out"...in our
case expanding doesn't spread out the swpX peers because all of their
sockunions are the same.
I looked at having peer_hash_make and peer_hash_same consider the ifname
of the swpX peer but that is a large change that we don't want to make
at the moment. So the fix is to put a cap on how large we are
willing to let the hash table get. By default there is no limit but if
max_size is set we will not allow the hash to expand above that.
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
This allows frr-reload.py (or anything else that scripts via vtysh)
to know if the vtysh command worked or hit an error.
When the BGP router-id changes, EVPN routes need to be processed due
to potential change to their RD.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Implement configuration options for EVPN. The configuration options include
VNI configuration with RD and Import and Export Route Targets. Also, display
the EVPN configuration.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Define the EVPN (EVI) hash table and related structures and initialize
and cleanup.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>