In the window immediately after an ES deletion bgpd can send MAC-IP updates
using that ES. Zebra needs to ignore these updates to prevent creation
of stale entries.
Ticket: #2668488
Signed-off-by: Anuradha Karuppiah <anuradhak@nvidia.com>
This addresses deletion of ES interfaces that are were not completely
configured.
Ticket: #2668488
Signed-off-by: Anuradha Karuppiah <anuradhak@nvidia.com>
Currently, the ll_type is set only in `netlink_interface` which is
executed only during startup. If the interface is created when the FRR
is already running, the type is not stored.
Fixes#1164.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
When a client sends to zebra that GR mode is being turned
on. The client also passes down the time zebra should hold
onto the routes. Display this time with the output
of the `show zebra client` command as well.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When issuing the `show zebra client` command data about
Graceful Restart state is being printed 2 times.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
In startup, zebra would dump interface information from Kernel in 3
steps w/o lock: step1, get interface information; step2, get interface
ipv4 address; step3, get interface ipv6 address.
If any interface gets added after step1, but before step2/3, zebra
would get extra interface addresses in step2/3 that has not been added
into zebra in step1. Returning error in the referenced interface lookup
would cause the startup interface retrieval to be incomplete.
Signed-off-by: Yuan Yuan <yyuanam@amazon.com>
FRR should only ever use the appropriate THREAD_ON/THREAD_OFF
semantics. This is espacially true for the functions we
end up calling the thread for.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
There's a helper function to check whether the interface is loopback or
VRF - if_is_loopback_or_vrf. Let's use it whenever we need to check that.
There's no functional change in this commit.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Pass down the safi for when we need address
resolution. At this point in time we are
hard coding the safi to SAFI_UNICAST.
Future commits will take advantage of this.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
PIM is going to need to be able to send down the address it is
trying to resolve in the multicast rib. We need a way to signal
this to the end developer. Start the conversion by adding the
ability to have a safi. But only allow SAFI_UNICAST at the moment.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The entirety of the import checking no longer needs to be
in zebra as that no-one is calling it. Remove the code.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
These are no longer really needed. The client just needs
to call nexthop resolution instead.
So let's remove the zapi types.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
There were two identical blocks of code run at init time that
requested info about AF_BRIDGE - don't see any reason to do that
twice, so remove one block.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
Because vrf backend may be based on namespaces, each vrf can
use in the [16-(2^32-1)] range table identifier for daemons that
request it. Extend the table manager to be hosted by vrf.
That possibility is disabled in the case the vrf backend is vrflite.
In that case, all vrf context use the same table manager instance.
Add a configuration command to be able to configure the wished
range of tables to use. This is a solution that permits to give
chunks to bgp daemon when it works with bgp flowspec entries and
wants to use specific iptables that do not override vrf tables.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When using bgp evpn rt5 setup, after BGP configuration has been
loaded, if the user attempts to detach and reattach the bridged
vxlan interface from the bridge, then BGP loses its BGP EVPN
contexts, and a refresh of BGP configuration is necessary to
maintain consistency between linux configuration and BGP EVPN
contexts (RIB). The following command can lead to inconsistency:
ip netns exec cust1 ip link set dev vxlan1000 nomaster
ip netns exec cust1 ip link set dev vxlan1000 master br1000
consecutive to the, BGP l2vpn evpn RIB is empty, and the way to
solve this until now is to reconfigure EVPN like this:
vrf cust1
no vni 1000
vni 1000
exit-vrf
Actually, the link information is correctly handled. In fact,
at the time of link event, the lower link status of the bridge
interface was not yet up, thus preventing from establishing
BGP EVPN contexts. In fact, when a bridge interface does not
have any slave interface, the link status of the bridge interface
is down. That change of status comes a bit after, and is not
detected by slave interfaces, as this event is not intercepted.
This commit intercepts the bridge link up event, and triggers
a check on slaved vxlan interfaces.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
when running bgp evpn rt5 setup, the Rmac sent in BGP updates
stands for the MAC address of the bridge interface. After
having loaded frr configuration, the Rmac address is not refreshed.
This issue can be easily reproduced by executing some commands:
ip netns exec cust1 ip link set dev br1000 address 2e🆎45:aa:bb:cc
Actually, the BGP EVPN contexts are kept unchanged.
That commit proposes to fix this by intercepting the mac address
change, and refreshing the vxlan interfaces attached to te bridge
interface that changed its MAC address.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
We should not be using `case default` with an enumerated type
This prevents the developer of new cases from knowing where
they need to fix by just compiling.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Move the handler for incoming interface address events
to a neutral source file - it's not netlink-specific and
shouldn't have been in a netlink file.
Signed-off-by: Mark Stapp <mjs.ietf@gmail.com>
Read incoming interface address change notifications in the
dplane pthread; enqueue the events to the main pthread
for processing. This is netlink-only for now - the bsd
kernel socket path remains unchanged.
Signed-off-by: Mark Stapp <mjs.ietf@gmail.com>
Add new apis for dplane interface address handling, based on
the existing api. The existing api is basically split in two:
the first part processes an incoming netlink message in the
dplane pthread, creating a dplane context with info about
the event. The second part runs in the main pthread and uses
the context data to update an interface or connected object.
Signed-off-by: Mark Stapp <mjs.ietf@gmail.com>
