Modified the configuration code to properly allow a peer-group member
to have a route-map out applied when one does not exist on the peer-group
itself. This capability already existed for route-map in.
Ticket: CM-10058
Signed-off-by: Don Slice
Reviewed-by: Donald Sharp
Quagga BGP needed a config 'bgp multiple-instance' in order to be able
to configure and use VRFs. Since this support is intrinsic to the
implementation, make this configuration on by default. Corresponding
change to 'show running-config' (and write) to display only if "no" is
configured.
This change will eliminate one unnecessary step in the configuration.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10070
Reviewed By: CCR-4383
Testing Done: Manual
When displaying the output of a 'show run',
display the neighbor information in an ordered
manner.
Ticket: CM-10184
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
When creating a 'struct peer' add in the ability to set the peer group
associated with that peer.
Ticket: CM-10184
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Upon receipt of incoming connection, a peer structure (doppelganger) is
created internally and the connection processed for it. The problem is
that in the case of BGP unnumbered, the sockunion structure within BGP was
being updated (in peer_create()) prior to the peer's flags being updated,
so it didn't take into account the 'v6only' configuration. This results
in subsequent problems when bgp_bind() is done - the socket ends up being
bound to the BGP instance instead of the interface.
In the case of an incoming connection, we should just use the addresses
on which the connection was setup/accepted, there is no need to attempt to
derive it again. Further, there is no need to attempt to update addresses
at the time of peer_create() since that is done when the connection is
attempted in bgp_start().
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-10028
Reviewed By: CCR-4373
Testing Done: Manual, bgpsmoke
Updates to routemaps and delete of the routemap were not working properly
for VRFs. This was because while routemaps are global, the routemap update
processing timer and the processing were at the per-instance level. This
approach was unable to handle processing for multiple instances as the
routemap has no tracking of which instances are still pending processing.
This lead to the processing happening correctly only for the first instance
- which could be the default instance or some other instance. It could also
result in reference to freed memory for an instance.
The fix done is to make the update/delete processing also global and not per
instance. This means that the route-map delay timer will be global and a global
thread will handle the change (or delete) for all instances instead of spawning
a separate thread for each instance. To support this, a global BGP command
"bgp route-map delay-timer <value>" has been implemented. The existing command
per-instance is not deleted but will update the global timer.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6970, CM-9918
Reviewed By: CCR-4320
Testing Done: Manual, bgpsmoke
Code changes to make unnumbered peering work in a VRF. The changes have
to do with locating the interface in the correct VRF (in order to look for
neighbor address) in the case of outgoing connections and when specifying
source address as well as fetching the correct instance for an incoming
connection based on reading the device the socket is bound to (the multi-vrf
socket option in the kernel).
Additionally, for IPv4 unnumbered peering in a VRF (based on /30 or /31
addresses), bind to the VRF rather than the interface.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9311
Reviewed By: CCR-4192
Testing Done: Manual, bgpsmoke
The BGP instance cleanup was deleting interfaces in that instance after
prior fixes, but this ended up deleting the interface list header which
was not being re-created. Added code to re-create this at the time an
instance is created.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-9466
Reviewed By: CCR-4164
Testing Done: Manual and verified failed test
Perform interface cleanup as an instance is deleted. This takes care of the
scenario when BGP exits (or is stopped/restarted) too as instances undergo
deletion and the interface cleanup is done as the last step in that.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Fixes: 46abd3e3e6
Ticket: CM-9410
Reviewed By: CCR-4143
Testing Done: Reran failed test
Link BGP instance (Default or VRF) to the corresponding VRF structure and
modify lookup to use this. The logic is very similar to what is implemented
in zebra - the 'struct zebra_vrf' there is essentially 'struct bgp' in BGP.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9122
Reviewed By: CCR-4102
Testing Done: Manual
With VRF support, certain objects are now maintained per BGP instance. At
exit, the list of BGP instances has to be freed only after processing the
per-instance objects.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Fixes: ad4cbda1a3
Ticket: CM-9340
Reviewed By:
Testing Done:
Various changes and fixes related to VRF registration, deletion,
BGP exit etc.
- Define instance type
- Ensure proper handling upon instance create, delete and
VRF add/delete from zebra
- Cleanup upon bgp_exit()
- Ensure messages are not sent to zebra for unknown VRFs
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9128, CM-7203
Reviewed By: CCR-4098
Testing Done: Manual
When a BGP instance is deleted through 'no router bgp', the required
cleanup was not being performed. This is after VRF-related changes.
Fix to ensure this is taken care of.
Note: Further changes needed in this area for VRFs.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9597
Reviewed By: CCR-4097
Testing Done: Verified failed test
While processing references to the macro PEERAF_FOREACH(), aggressive loop
optimization by gcc 4.9.x (probably 4.8 and greater) was resulting in the
generated code not checking on the index as well as eliminating some code.
This was leading to a dereference of invalid memory when a BGP peer came up.
The fix is to scrap this convoluted macro. Two other changes done are to
eliminate overloading of "afindex" and make the loop iterator an integer.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Dave Olson <olson@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Ticket: CM-8889
Reviewed By: CCR-4018
Testing Done: Verified failure scenario
Note: This code was added as part of update-groups implementation; when
upstreaming update-groups, this patch should also be included.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-8788
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8472
The first as-path is what the original as-path for the test, the second
is what the as-path should look like once all confed SETs and SEQs have
been removed. At the time the test was written quagga did not correctly
remove confed SETs and SEQs but whoever wrote the test didn't notice
this and assumed that the behavior they were seeing was correct so used
that output to populate the second as-path.
Now that we do correctly remove the confed parts these tests fail. So
the fix is to update the second as-path for these two tests so that they
no longer contain any confed SETs/SEQs.
BGP uses a second #define that is equal to MULTIPATH_NUM. There
is no point in having a different #define. Just consolidate.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
configuration
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Ticket: CM-8321
This allows the user to configure the peer-group as an option for the
"neighbor swpX interface" command.
{code}
!
router bgp 100
neighbor FOO peer-group
neighbor FOO remote-as external
neighbor swp1 interface
neighbor swp2 interface v6only
neighbor swp3 interface peer-group FOO
neighbor swp4 interface v6only peer-group FOO
!
address-family ipv4 unicast
neighbor FOO activate
neighbor swp1 activate
neighbor swp2 activate
exit-address-family
!
{code}
Note that if the user configures
{code}
neighbor swp5 interface
neighbor swp5 peer-group FOO
{code}
We will display that as "neighbor swp5 interface peer-group FOO". It
did not seem worth tracking that the peer-group was entered via two
lines instead of one.
During CR for nexthop upstream it was noticed that usage
of prefix2str was not consistent. This fixes this problem
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
BGP is currently displaying the in-use router-id in the config. This is
conditional on a CONFIG flag, however, that flag is set even when there
is no configured router-id and the router-id learnt from Zebra is in-use.
The CONFIG flag for router-id is redundant since there is a separate
variable for the configured value, so use that and deprecate the CONFIG
flag. This also makes BGP behave like OSPF.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Ticket: CM-8077, CM-8220
Reviewed By: CCR-3793
Testing Done: Manual verification (in 2.5-br)
Note: Imported from 2.5-br patch bgpd-fix-router-id-config-display.patch
Modify code to recognize that we are not actually reseting the
neighbor if the user actually enters a remote-as of external->external
for a neighbor.
Ticket: CM-8100
Reviewed-by: CCR-3783
Testing: See bug
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8122
per draft-ietf-idr-ix-bgp-route-server-09:
2.3.2.2.2. BGP ADD-PATH Approach
The [I-D.ietf-idr-add-paths] Internet draft proposes a different
approach to multiple path propagation, by allowing a BGP speaker to
forward multiple paths for the same prefix on a single BGP session.
As [RFC4271] specifies that a BGP listener must implement an implicit
withdraw when it receives an UPDATE message for a prefix which
already exists in its Adj-RIB-In, this approach requires explicit
support for the feature both on the route server and on its clients.
If the ADD-PATH capability is negotiated bidirectionally between the
route server and a route server client, and the route server client
propagates multiple paths for the same prefix to the route server,
then this could potentially cause the propagation of inactive,
invalid or suboptimal paths to the route server, thereby causing loss
of reachability to other route server clients. For this reason, ADD-
PATH implementations on a route server should enforce send-only mode
with the route server clients, which would result in negotiating
receive-only mode from the client to the route server.
This allows us to delete all of the following code:
- All XXXX_rsclient() functions
- peer->rib
- BGP_TABLE_MAIN and BGP_TABLE_RSCLIENT
- RMAP_IMPORT and RMAP_EXPORT
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com
Ticket: CM-8014
This implements addpath TX with the first feature to use it
being "neighbor x.x.x.x addpath-tx-all-paths".
One change to show output is 'show ip bgp x.x.x.x'. If no addpath-tx
features are configured for any peers then everything looks the same
as it is today in that "Advertised to" is at the top and refers to
which peers the bestpath was advertise to.
root@superm-redxp-05[quagga-stash5]# vtysh -c 'show ip bgp 1.1.1.1'
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Advertised to non peer-group peers:
r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Last update: Fri Oct 30 18:26:44 2015
[snip]
but once you enable an addpath feature we must display "Advertised to" on a path-by-path basis:
superm-redxp-05# show ip bgp 1.1.1.1/32
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:44 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r3(10.0.0.3) (10.0.0.3)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 7
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r6(10.0.0.6) (10.0.0.6)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 6
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r5(10.0.0.5) (10.0.0.5)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 5
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r4(10.0.0.4) (10.0.0.4)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 4
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r1(10.0.0.1) (10.0.0.1)
Origin IGP, metric 0, localpref 100, valid, internal, best
AddPath ID: RX 0, TX 3
Advertised to: r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Last update: Fri Oct 30 18:26:34 2015
superm-redxp-05#
BGP ORF prefix lists are in a separate namespace; this was previously
hooked up with a special-purpose AFI value. This is a little kludgy for
extension, hence this splits it off.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
These are about to be touched and there's no point in other code
touching into prefix list's internas. Add some isolation.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-7926
There was a crash from not NULLing out peer->hostname but I cleaned
up a bunch of other suspect ones as well.
