When we uplifted the cli from old -> new, I did not properly
handle the switch from <1-3> to (1-3) for number ranges.
Also fix some minor variable renaming that happened?
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This was causing a crash when no group address was passed
because a garbage pointer valuse was used. It also was ignoring
the group address when passing one.
Signed-off-by: Jafar Al-Gharaibeh <jafar@atcorp.com>
During neighbor down event, all upstream entries rpf lookup may result
into nhop address with 0.0.0.0 and rpf interface info being NULL.
Put preventin check where rpf interface info is accessed.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
During processing of Join/Prune,
for a S,G entry, current state is SGRpt, when only *,G is
received, need to clear SGRpt and add/inherit the *,G OIF to S,G so
it can forward traffic to downstream where *,G is received.
Upon receiving SGRpt prune remove the inherited *,G OIF.
Testing Done:
Trigger SPT switchover, *,G path received SGRpt later data
traffic stopped S,G ages out from LHR, sends only
*,G join to upstream, verified S,G entry inherit the OIF.
Upon receiving SGRpt deletes inherited oif and retains in SGRpt state.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Execute ip igmp version 3 under swp interface,
verified show running displayed 'ip igmp' configuration.
Continuous sending group membership, performed 'no ip igmp'
and verified, group membership flushed. Performed
'ip igmp version 3', verified 'show ip igmp groups'
displaying igmp membership re-populated.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
In this patch, PIM nexthop tracking uses locally populated nexthop cached list
to determine ECMP based nexthop (w/ ECMP knob enabled), otherwise picks
the first nexthop as RPF.
Introduced '[no] ip pim ecmp' command to enable/disable PIM ECMP knob.
By default, PIM ECMP is disabled.
Intorudced '[no] ip pim ecmp rebalance' command to provide existing mcache
entry to switch new path based on hash chosen path.
Introduced, show command to display pim registered addresses and respective nexthops.
Introuduce, show command to find nexthop and out interface for (S,G) or (RP,G).
Re-Register an address with nexthop when Interface UP event received,
to ensure the PIM nexthop cache is updated (being PIM enabled).
During PIM neighbor UP, traverse all RPs and Upstreams nexthop and determine, if
any of nexthop's IPv4 address changes/resolves due to neigbor UP event.
Testing Done: Run various LHR, RP and FHR related cases to resolve RPF using
nexthop cache with ECMP knob disabled, performed interface/PIM neighbor flap events.
Executed pim-smoke with knob disabled.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
(cherry picked from commit cba4448178)
We have a bunch of places where we iterate over
the pim_ifchannel_list to find those ifchannels
that match a certain upstream. Since we already
know in the upstream the list of ifchannels
associated with it, just look at those instead.
Functions changed:
forward_on
forward_off
pim_upstream_rpf_interface_changed
pim_upstream_update_could_assert
pim_upstream_update_my_assert_metric
pim_upstream_update_assert_tracking_desired
pim_upstream_is_sg_rpt
Ticket: CM-15629
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a list structure to track the ifchannels associated
with a particular upstream.
We are not doing anything with this particular knowledge
yet but it will be come useful in the near future.
Ticket: CM-15629
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we are determining an inherited_olist, let's be allot
smarter about what we look at. Before this code change
we are looping over the entirety of all ifchannels in
the system to find the relevant ones. Convert the
code to *find*(hash table lookup) the specific ifchannels we
are interested in.
Ticket: CM-15629
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we have a S,G that was created due to the *,G IGMP
report going away, safely remove the S,G as well.
Ticket: CM-15838
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
To the 'ip pim spt-switchover infinity-and-beyond' command
add 'prefix-list <PLIST>'. To the command.
Use this as the basis to deny (Not immediate switchover)
or permit (Immediate switchover), based upon matching
the group address and the prefix-list.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we have a *,G mroute that starts receiving any particular
S,G, we will get wholepkt callbacks due to the pimreg in the
OIL for the *,G.
So we need to do SPT switchover, but this can fail if we
do not have a path to the S( but we do to the RP!).
In this case fail gracefully.
Ticket: CM-15621
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This allows SPT switchover for S,G upon receipt of packets
on the LHR.
1) When we create a *,G from a IGMP Group Report, install
the *,G route with the pimreg device on the OIL.
2) When a packet hits the LHR that matches the *,G, we will
get a WHOLEPKT callback from the kernel and if we cannot
find the S,G, that means we have matched it on the LHR via
the *,G mroute. Create the S,G start the KAT and run
inherited_olist.
3) When the S,G times out, safely remove the S,G via
the KAT expiry
4) When the *,G is removed, remove any S,G associated
with it via the LHR flag.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When terminating pim, there existed( albeit small ) the chance
to cause a crash. Cleanup the termination to not have
that chance.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
It is impossible for the list->cmp function to
ever be handed NULL values as the arguments.
Clean up this in the code.
Additionally consolidate the exact same two functions
into 1 function.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There is no need for a function that calls another function.
Additionally, nexthop_updates from zebra can be either
ZEBRA_NEXTHOP_UPDATE -or-
ZEBRA_IMPORT_CHECK_UPDATE
If we were to receive a IMPORT_CHECK_UPDATE the code
would cause a immediate crash. Fix this
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There exists a common pattern in pim where we were setting
a variable to a value in the error case when we would no
longer need it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In certain conditions when we are deleting the interface
from an OIL do not delete the mroute. That decision
should be made by the state machine.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Interface type has been replaced with the SSM range config. And SSM
groups can now co-exists with ASM groups. I have left the pim ssm
per-interface cli control hidden. It now enables pim-sm with a warning.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-15344
Testing Done: pim-smoke
SSM groups (232/8 or user configured SSM range) can exist in the same
multicast network as ASM groups. For such groups all RPT related state
machine operations have to be skipped as defined by section 4.8 of
RFC4601 -
1. Source registration is skipped for SSM groups. For SSM groups mroute
is setup on the FHR when a new multicast flow is rxed; however source
registration (i.e. pimreg join) is skipped. This will let the ASIC black
hole the traffic till a valid OIL is added to the mroute.
2. (*,G) IGMP registrations are ignored for SSM groups.
Sample output:
=============
fhr# sh ip pim group-type
SSM group range : 232.0.0.0/8
fhr# sh ip pim group-type 232.1.1.1
Group type: SSM
fhr# sh ip pim group-type 239.1.1.1
Group type: ASM
fhr#
Sample config:
=============
fhr(config)# ip pim ssm prefix-list ssm-ranges
fhr(config)#
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-15344
Testing Done:
1. SSM/ASM source-registration/igmp-joins.
2. On the fly multicast group type changes.
3. pim-smoke.
When we get a SGrpt Prune embedded in the *,G Join,
Display the created ifchannel as being SGRpt state.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
pim_jp_agg list should not ref count pim_upstream as that
the deletion of pim_upstream deletion should remove
the pim_upstream from the j/p agg list.
Cleanup a memory leag of jag
Make comparison of js cleaner in add_group
Move THREAD_OFF to before the neighbor find.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Suppose you have a unnumbered ecmp connections between
two switches:
st1-l3# show ip pim neighbor
Interface Neighbor Uptime Holdtime DR Pri
swp52 6.0.0.10 00:00:01 00:00:29 1
swp53 6.0.0.10 00:00:06 00:00:26 1
And for a given (S,G) the RPF goes:
st1-l3# show ip nht
99.1.1.1
resolved via bgp
fe80::4e76:25ff:fee7:42d1, via swp52
fe80::4e76:25ff:fee7:42d5, via swp53
Client list: pim(fd 14)
Now suppose, 52 is the choosen RPF( since we can only pick one )
and the interface goes down. As such we will choose to use
swp53.
The problem was that the pim_rpf_update call is made
it will change the rpf interface to 53, but not tell
the calling function that the RPF_CHANGED because
it is only looking at the rpf_addr(the nexthop)
to see if it is changed and if we are in an unnumbered
dual ecmp to the same box it was not detecting and
notifying.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
