Before the fix:
2019/11/14 19:52:21 BGP: peer 192.168.2.5 deleted from subgroup s4peer
cnt 0 - missing space after s4 before peer
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
The bug:
As part of displaying advertised routes to a peer, in the outer loop, we
iterate through all prefixes in the evpn table. In the inner loop,
we iterate through adj_out of each prefix.
If a prefix which is present in the evpn table is not advertised to a peer,
its corresponding attr == NULL. Checking for this condition is the fix.
Signed-off-by: Lakshman Krishnamoorthy <lkrishnamoor@vmware.com>
PR 5118 introduce additional (prepend) keywords
like 'ip' to Route Distinguisher output which
breaks existing evpn route show commands parsing.
Restore to original behavior.
Testing Done:
vtysh -c 'show bgp l2vpn evpn route'
Before fix:
Route Distinguisher: ip 27.0.0.15:44
Post fix:
Route Distinguisher: 27.0.0.15:44
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Recently had a case where I was attempting to debug a nexthop tracking
issue across multiple bgp vrf's and since the setup vrf's in it with
overlapping address ranges, it became real fun real fast to track
vrf data associated. Add a bit of code to allow us to figure out
what vrf we are in when we print out debug messages.
Look through the rest of the code and find debugs where we are
not using bgp->name_pretty and switch it over.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Prevent IPv6 Link-local address being forward to IBGP peer,
which are not directly connected.
R1----IPV6-unnumbered-EBGP-------R2-----IPV6-IBGP-----R3
Configure route-map to set preferred global address on and apply
route-map-IN on R2 for R1-R2 session. Now check on R3's BGP and
RIB table has route nexthop as R1 link-local address, which is
not correct.
As of now we clear link-local address info from mp_nexthop_global,
only if mp_nexthop_global is populated with link-local address.
We should do it even if route-map is configured boz forwarding
link-local address from one link scope to another is violation of
the standards.
Signed-off-by: Biswajit Sadhu sadhub@vmware.com
This commit make bgpd to skip and ignore unsupported
sub-type of PREFIX_SID. (especially new defined sub-type)
Current bgpd can't parase unsupported sub-type of PREFIX_SID.
PREFIX_SID is drafted on draft-ietf-idr-bgp-prefix-sid-27.
There are already new sub-type drafted on
draft-dawra-idr-srv6-vpn-05. (Type5,6 is new defined.)
This commit fix the problem reported as #5277 on GitBub.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
The sender side AS path loop detection code was implemented since the
import of Quagga code, however it was always disabled by a `ifdef`
guard.
Lets allow the user to decide whether or not to enable this feature on
run-time.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Scenarios where this code change is required:
1. BFD is un-configured from BGP at remote end.
Neighbour BFD sends ADMIN_DOWN state, but BFD on local side will send
DOWN to BGP, resulting in BGP session DOWN.
Removing BFD session administratively shouldn't bring DOWN BGP session
at local or remote.
2. BFD is un-configured from BGP or shutdown locally.
BFD will send state DOWN to BGP resulting in BGP session DOWN.
(This is akin to saying do not use BFD for BGP)
Removing BFD session administratively shouldn't bring DOWN BGP session at
local or remote.
Signed-off-by: Sayed Mohd Saquib sayed.saquib@broadcom.com
Since we don't set a value from the return of bgp_path_info_mpath_next
it is impossible for this function to do anything as such the if statement
is dead code as well.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem reported with error messages appearing in the log
complaining about invalid afi/safi combinations. Determined
that the error messages were recently added in the function
that turns afi and safi values to strings. Unfortunately,
the function is called from places using FOREACH_AFI_SAFI,
which spins thru every afi and safi number including some
that are not legal together (ipv4 evpn and l2vpn multicast
for example.) This fix removes these error messages since
it is not necessarily an error to call it with invalid
combinations.
Ticket: CM-26883
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Coverity has found a path where the attr.aspath may be NULL.
assert that the aspath is non-null so we can make this go away.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We make the assumption that ->attr is not NULL throughout
the code base. We are totally inconsistent about application
of this though.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add -s X or --socket_size X to the bgp cli to allow
the end user to specify the outgoing bgp tcp kernel
socket buffer size.
It is recommended that this option is only used on
large scale operations.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In bgp_create_evpn_bgp_path_info we create a bgp_path_info
that should be returned since we need it later.
Found by Coverity Scan.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When using soft reconfiguration inbound we are storing packet
data on the side for replaying when necessary. The problem here
is that we are just grabbing the first bgp_path_info and using
that as the base. What happens when we have soft-reconfig turned
on with multiple bgp_path_info's for a path? This was introduced
in commit 8692c50652, yes back
in 2012! I would argue, though, that it was just broken
in a different way before this.
Choose the correct bgp_path_info that corresponds to the peer
we received the data from for rethinking.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
