There are cases where the table identifier is set on a bgp entry, mainly
due to route-map, and associate fib entry needs to be removed.
This change encompasses also the route-map reconfiguration that leads to
removing the previous entry, whereas bgp update had been triggered (
this happens when software inbound reconfiguration is handled).
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
this table identifier can be used for policy routing. incoming entries
are locally exported to that local table identifier.
note that so that the user applies the new table identifier to all
entries, the user should flush local tables first.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The bgp pointer may not be actually found. The debug
message that was using it could get the same value
another way. Convert over
Fixes Coverity Scan Issue:
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
For all the places we have a zclient->interface_up convert
them to use the interface ifp_up callback instead.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Switch the zclient->interface_add functionality to have everyone
use the interface create callback in lib/if.c
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Start the conversion to allow zapi interface callbacks to be
controlled like vrf creation/destruction/change callbacks.
This will allow us to consolidate control into the interface.c
instead of having each daemon read the stream and react accordingly.
This will hopefully reduce a bunch of cut-n-paste stuff
Create 4 new callback functions that will be controlled by
lib/if.c
create -> A upper level protocol receives an interface creation event
The ifp is brand spanking newly created in the system.
up -> A upper level protocol receives a interface up event
This means the interface is up and ready to go.
down -> A upper level protocol receives a interface down
destroy -> A upper level protocol receives a destroy event
This means to delete the pointers associated with it.
At this point this is just boilerplate setup for future commits.
There is no new functionality.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
in addition to support for tcpflags, it is possible to filter on any
protocol. the filtering can then be based with iptables.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Field vrf_id is replaced by the pointer of the struct vrf *.
For that all other code referencing to (interface)->vrf_id is replaced.
This work should not change the behaviour.
It is just a continuation work toward having an interface API handling
vrf pointer only.
some new generic functions are created in vrf:
vrf_to_id, vrf_to_name,
a zebra function is also created:
zvrf_info_lookup
an ospf function is also created:
ospf_lookup_by_vrf
it is to be noted that now that interface has a vrf pointer, some more
optimisations could be thought through all the rest of the code. as
example, many structure store the vrf_id. those structures could get
the exact vrf structure if inherited from an interface vrf context.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
vrf_id parameter is replaced with struct vrf * parameter. It is
needed to create vrf structure before entering in the fuction.
an error is generated in case the vrf parameter is missing.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
the vrf_id parameter is replaced by struct vrf * parameter.
this impacts most of the daemons that look for an interface based on the
name and the vrf identifier.
Also, it fixes 2 lookup calls in zebra and sharpd, where the vrf_id was
ignored until now.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Set the bgp default nexthop value of IPv6 to the local ipv6 addr of the
tcp connection like IPv4. Fixed the problem of route with empty nexthop
advertised to the peer when zebra is not running.
* bgp_zebra.c: (bgp_zebra_nexthop_set) Set IPv6 bgp default nexthop value.
Signed-off-by: Faicker Mo <faicker.mo@ucloud.cn>
vrf_id parameter is added to the api of bfd_client_sendmsg().
this permits being registered to bfd from a separate vrf.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This macro:
- Marks ZAPI callbacks for readability
- Standardizes argument names
- Makes it simple to add ZAPI arguments in the future
- Ensures proper types
- Looks better
- Shortens function declarations
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
If PIM-SM if used for BUM flooding the multicast group address can be
configured per-vxlan-device. BGP receives this config from zebra via
the L2 VNI add/update.
Sample output -
root@TORS1:~# vtysh -c "show bgp l2vpn evpn vni 1000" |grep Mcast
Mcast group: 239.1.1.100
root@TORS1:~#
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
force allocation of entries in order to save memory and then save memory
for people that do not use flowspec.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
bgp entries in bgp_extra_path structure will be allocated as lists, only
when needed, that is to say when bgp fs entries will be received and
installed on the underlying system.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This replaces manual checks of the flag with a wrapper macro to convey
the meaning "is evpn enabled on this vrf?"
Signed-off-by: Tuetuopay <tuetuopay@me.com>
Sponsored-by: Scaleway
This makes the instance bearing the advertise-all-vni config option
register to zebra as the EVPN one, forwarding it the option.
Signed-off-by: Tuetuopay <tuetuopay@me.com>
Sponsored-by: Scaleway
Found that previous fix for this issue caused collatoral damage and
reverted that fix. This fix clears the vrf_bitmaps when the vrf is
disabled/deleted and then re-applies the redist config when the vrf
is re-enabled.
Ticket: CM-24231
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
In the case of EVPN symmetric routing, the tenant VRF is associated with
a VNI that is used for routing and commonly referred to as the L3 VNI or
VRF VNI. Corresponding to this VNI is a VLAN and its associated L3 (IP)
interface (SVI). Overlay next hops (i.e., next hops for routes in the
tenant VRF) are reachable over this interface. Howver, in the model that
is supported in the implementation and commonly deployed, there is no
explicit Overlay IP address associated with the next hop in the tenant
VRF; the underlay IP is used if (since) the forwarding plane requires
a next hop IP. Therefore, the next hop has to be explicit flagged as
onlink to cause any next hop reachability checks in the forwarding plane
to be skipped.
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement
section 4.4 provides additional description of the above constructs.
Use existing mechanism to specify the nexthops as onlink when installing
these routes from bgpd to zebra and get rid of a special flag that was
introduced for EVPN-sourced routes. Also, use the onlink flag during next
hop validation in zebra and eliminate other special checks.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
In the case of EVPN symmetric routing, the tenant VRF is associated with
a VNI that is used for routing and commonly referred to as the L3 VNI or
VRF VNI. Corresponding to this VNI is a VLAN and its associated L3 (IP)
interface (SVI). Overlay next hops (i.e., next hops for routes in the
tenant VRF) are reachable over this interface.
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement
section 4.4 provides additional description of the above constructs.
Use the L3 interface exchanged between zebra and bgp in route install.
This patch in conjunction with the earlier one helps to eliminate some
special code in zebra to derive the next hop's interface.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
In the case of EVPN symmetric routing, the tenant VRF is associated with
a VNI that is used for routing and commonly referred to as the L3 VNI or
VRF VNI. Corresponding to this VNI is a VLAN and its associated L3 (IP)
interface (SVI). Overlay next hops (i.e., next hops for routes in the
tenant VRF) are reachable over this interface.
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement
section 4.4 provides additional description of the above constructs.
The implementation currently derives this L3 interface for EVPN tenant
routes using special code that looks at route flags. This patch
exchanges the L3 interface between zebra and bgpd as part of the L3-VNI
exchange in order to eliminate some this special code.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
A few code paths weren't handling the vpnv6 nexthop lenghts as
expected, which was leading to problems like imported vpnv6 routes
not being marked as valid when they should. Fix this.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Made changes and updated the routemap applied counter in the following flows.
1.Increment when route map attached to a list.
2.Decrement when route map removed / modified from a list.
3.Increment/decrement when route map create/delete callback triggered.
4.Besides ,This counter need not be updated when a route map is got updated.
i.e changing/adding a match value to the existing routemap.
In BGP , same update api called for all three add/delete/update operation .
But this counter have to be updated only for routemap addition.
Addressed this specific change by identifying the routemap operation based
on routemap pointer.
Signed-off-by: RajeshGirada <rgirada@vmware.com>
the list of iprules is displayed in the 'show bgp ipv4 flowspec detail'
The list of iprules is displayed, only if it is installed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
two kind of rules are being set from bgp flowspec: ipset based rules,
and ip rule rules. default route rules may have a lower priority than
the other rules ( that do not support default rules). so, if an ipset
rule without fwmark is being requested, then priority is arbitrarily set
to 1. the other case, priority is set to 0.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
because ip rule creation is used to not only handle traffic marked by
fwmark; but also for conveying traffic with from/to rules, a check of
the creation must be done in the linked list of ip rules.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
now, ip rule can be created from two differnt ways; however a single
zebra API has been defined. so make it consistent by adding a parameter
to the bgp zebra layer. the function will handle the rest.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When an inactive-neigh delete is rxed bgp will not have a local path to
remove (and re-run path selection). Instead it simply re-installs the
current best remote path if any.
Ticket: CM-23018
Testing Done: evpn-min
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Duplicate address detection configuration clis
under bgp l2vpn evpn config mode.
- Enabled/Disable (global knob) for feature.
- Configure cli for duplicate detection action
freeze and freze until time (auto-recovery).
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
The bgp_info data is stored as a void pointer in `struct bgp_node`.
Abstract retrieval of this data and setting of this data
into functions so that in the future we can move around
what is stored in bgp_node.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
It's been a year since we added the new optional parameters
to instantiation. Let's switch over to the new name.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If we attempt to register nexthops before we have the zebra
connection, they will not be installed. After we have noticed
that we are up, re-install them.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow some debug notification when we are unable to talk
to zebra due to the connection not being there yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the '[no] flood <disable|head-end-replication>' command
to the l2vpn evpn afi/safi sub commands for bgp. This command
when entered as 'flood disable' will turn off type 3 route
generation for the transmittal of the type 3 route necessary
for BUM replication on the remote VTEP. Additionally it will
turn off the BUM handling via the new zebra command,
ZEBRA_VXLAN_FLOOD_CONTROL.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the modification of whether or not we will allow
BUM flooding on the vxlan bridge. To do this allow
the upper level protocol to specify via the ZEBRA_VXLAN_FLOOD_CONTROL
zapi message.
If flooding is disabled then BUM traffic will not be forwarded
to other VTEP's.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Do a straight conversion of `struct bgp_info` to `struct bgp_path_info`.
This commit will setup the rename of variables as well.
This is being done because `struct bgp_info` is not descriptive
of what this data actually is. It is path information for routes
that we keep to build the actual routes nexthops plus some extra
information.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In bgp if we have not configured bgp we were ignoring
interface based callbacks. Leading to states where
we may not be processing interface information.
Leading to states where we do not actually keep
ifp data. As an example:
Suppose vrf A and vrf B. A has interface swp1.
At the same time we only have a `router bgp 9 vrf B`
When we received the callback for moving swp1
from vrf A to vrf B we were not processing the
move at all and BGP would not consider the interface
part of vrf B at all.
This commit makes bgp pay attention to interface
events irrelevant if bgp is using that vrf. This
is now consistent with how the lib/if* expects
to work and the rest of the daemons in FRR.
Signed-off-by: Donald Sharp <sharpd@cumulsnetworks.com>
Corrections so that the BGP daemon can work with the label manager properly
through a label-manager proxy. Details:
- Correction so the BGP daemon behind a proxy label manager gets the range
correctly (-I added to the BGP daemon, to set the daemon instance id)
- For the BGP case, added an asynchronous label manager connect command so
the labels get recycled in case of a BGP daemon reconnection. With this,
BGPd and LDPd would behave similarly.
Signed-off-by: F. Aragon <paco@voltanet.io>
When using `no bgp fast-external-failover` and a interface moves
from one vrf into another we would not fully process the change.
Fix this code path.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The peer->nexthop.ifp pointer must be set when parsing the
attributes in bgp_mp_reach_parse, notice this
and fail gracefully.
Rework bgp_nexthop_set to remove the HAVE_CUMULUS and to
fail the nexthop_set when we have a zebra connection and
no ifp pointer, as that not havinga zebra connection and
no ifp pointer is legal.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Added parameter in bgp_redistribute_set() to indicate change
in redistribute option
* If there is change, call bgp_redistribute_unreg() to withdraw routes
Signed-off-by: kssoman <somanks@vmware.com>
Implement procedures similar to what is specified in
https://tools.ietf.org/html/draft-malhotra-bess-evpn-irb-extended-mobility
in order to support extended mobility scenarios in EVPN. These are scenarios
where a host/VM move results in a different (MAC,IP) binding from earlier.
For example, a host with an address assignment (IP1, MAC1) moves behind a
different PE (VTEP) and has an address assignment of (IP1, MAC2) or a host
with an address assignment (IP5, MAC5) has a different assignment of (IP6,
MAC5) after the move. Note that while these are described as "move" scenarios,
they also cover the situation when a VM is shut down and a new VM is spun up
at a different location that reuses the IP address or MAC address of the
earlier instance, but not both. Yet another scenario is a MAC change for an
attached host/VM i.e., when the MAC of an attached host changes from MAC1 to
MAC2. This is necessary because there may already be a non-zero sequence
number associated with MAC2. Also, even though (IP, MAC1) is withdrawn before
(IP, MAC2) is advertised, they may propagate through the network differently.
The procedures continue to rely on the MAC mobility extended community
specified in RFC 7432 and already supported by the implementation, but
augment it with a inheritance mechanism that understands the relationship
of the host MACIP (ARP/neighbor table entry) to the underlying MAC (MAC
forwarding database entry). In FRR, this relationship is understood by the
zebra component which doubles as the "host mobility manager", so the MAC
mobility sequence numbers are determined through interaction between bgpd
and zebra.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Because one flowspec entry can create 1-N bgp pbr entries, the list is
now updated and visible. Also, because the bgp_extra structure is used,
this list is flushed when the bgp_extra structure is deleted.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This commit removes various parts of the bgpd implementation code which
are unused/useless, e.g. unused functions, unused variable
initializations, unused structs, ...
Signed-off-by: Pascal Mathis <mail@pascalmathis.com>
The flowspec fragment attribute is taken into account to be pushed in
BGP policy routing entries. Valid values are enumerate list of 1, 2, 4,
or 8 values. no combined value is supported yet.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The rearrangement of where the decision point of
filling in the aggregate information, must have allowed
SA to find a path of code where we may use ifindex uninitialized.
While I don't think this is possible to happen, make this issue
go away.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The aggregate-address command is not creating the null0
route. This got lost somewhere in the last year or so.
Add this ability back for BGP route installs into
zebra.
We need this aggregate route installed into the rib
because we are drawing this traffic to us irrelevant
of the number of routes we do have for that prefix.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Sometimes at startup, BGP Flowspec may be allocated a routing table
identifier not in the range of the predefined table range.
This issue is due to the fact that BGP peering goes up, while the BGP
did not yet retrieve the Table Range allocator.
The fix is done so that BGP PBR entries are not installed while
routing table identifier range is not obtained. Once the routing table
identifier is obtained, parse the FS entries and check that all selected
entries are installed, and if not, install it.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
By default, some debug traces were displayed. Those pbr traces are
hidden with 'debug bgp zebra' command.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
policy routing is configurable via address-family ipv4 flowspec
subfamily node. This is then possible to restrict flowspec operation
through the BGP instance, to a single or some interfaces, but not all.
Two commands available:
[no] local-install [IFNAME]
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Once PBR rules installed, an information is printed in the main
show bgp ipv4 flowspec detail information.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Those 3 fields are read and written between zebra and bgpd.
This permits extending the ipset_entry structure.
Combinatories will be possible:
- filtering with one of the src/dst port.
- filtering with one of the range src/ range dst port
usage of src or dst is exclusive in a FS entry.
- filtering a port or a port range based on either src or dst port.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When rule add transaction is sent from bgpd to zebra, the reference
context must not be incremented while the confirmation message of
install has not been sent back; unless if the transaction failed to be
sent.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The debugging message in charge of showing if the route is added or
witdrawn is changed accordingly to reflect this status.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
