Change timestamp parameter from int to time_t to avoid truncation.
Found by Coverity Scan (CID 1563226 and 1563222)
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This command makes unplanned GR more reliable by manipulating the
sending of Grace-LSAs and Hello packets for a certain amount of time,
increasing the chance that the neighboring routers are aware of
the ongoing graceful restart before resuming normal OSPF operation.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In practical terms, unplanned GR refers to the act of recovering
from a software crash without affecting the forwarding plane.
Unplanned GR and Planned GR work virtually the same, except for the
following difference: on planned GR, the router sends the Grace-LSAs
*before* restarting, whereas in unplanned GR the router sends the
Grace-LSAs immediately *after* restarting.
For unplanned GR to work, ospf6d was modified to send a
ZEBRA_CLIENT_GR_CAPABILITIES message to zebra as soon as GR is
enabled. This causes zebra to freeze the OSPF routes in the RIB as
soon as the ospf6d daemon dies, for as long as the configured grace
period (the defaults is 120 seconds). Similarly, ospf6d now stores in
non-volatile memory that GR is enabled as soon as GR is configured.
Those two things are no longer done during the GR preparation phase,
which only happens for planned GRs.
Unplanned GR will only take effect when the daemon is killed
abruptly (e.g. SIGSEGV, SIGKILL), otherwise all OSPF routes will be
uninstalled while ospf6d is exiting. Once ospf6d starts, it will
check whether GR is enabled and enter in the GR mode if necessary,
sending Grace-LSAs out all operational interfaces.
One disadvantage of unplanned GR is that the neighboring routers
might time out their corresponding adjacencies if ospf6d takes too
long to come back up. This is especially the case when short dead
intervals are used (or BFD). For this and other reasons, planned
GR should be preferred whenever possible.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Effectively a massive search and replace of
`struct thread` to `struct event`. Using the
term `thread` gives people the thought that
this event system is a pthread when it is not
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Upon exiting the GR mode, force reorigination of intra-area-prefix-LSAs
on all attached areas. This is to ensure all configured areas will have
an associated intra-area-prefix-LSA at the end of the GR procedures,
even if the area doesn't have any full adjacency.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This commit fixes a bug where self-originated NSSA/AS-External LSAs
would age out about one hour after exiting from the GR mode. The
reason is because received self-originated LSAs aren't registered
for periodic refreshing, so that needs to be done manually. Fix
this by explicitly reoriginating all NSSA/AS-External LSAs while
exiting from the GR mode.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
RFC 5340 says that Link-LSAs should not be originated for virtual
links. Add a check to prevent that from happening while exiting
from the GR mode.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Rather than running selected source files through the preprocessor and a
bunch of perl regex'ing to get the list of all DEFUNs, use the data
collected in frr.xref.
This not only eliminates issues we've been having with preprocessor
failures due to nonexistent header files, but is also much faster.
Where extract.pl would take 5s, this now finishes in 0.2s. And since
this is a non-parallelizable build step towards the end of the build
(dependent on a lot of other things being done already), the speedup is
actually noticeable.
Also files containing CLI no longer need to be listed in `vtysh_scan`
since the .xref data covers everything. `#ifndef VTYSH_EXTRACT_PL`
checks are equally obsolete.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
a) Remove setting of thread pointer to NULL after
thread invocation, this is already done.
b) Use thread_is_scheduled()
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Some CI VMs are using really old versions of json-c (pre 2013 [1])
that expect filenames to be passed as "char *" instead of "const char *".
Add some explicit casts to fix the resulting compiler errors on those
VMs (passing "char *" when the API expects "const char *" is fine).
Hopefully this commit should be reverted once the CI is updated to use
newer versions of json-c.
[1] https://github.com/json-c/json-c/commit/20e4708c
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
RFC 5187 specifies the Graceful Restart enhancement to the OSPFv3
routing protocol. This commit implements support for the GR
restarting mode.
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ipv6
ospf` EXEC-level command needs to be issued before restarting the
ospf6d daemon (there's no specific requirement on how the daemon
should be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospf6d is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
