The usage of bgp_vrf does not need to be tested
at this point since it's already been derefed in all
paths to this point.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
A route-map applied on incoming BGP updates is not able
to replace an unwanted as segments by another one.
unwanted as segment are based on an AS path access-list.
The below configuration illustrates the case:
router bgp 65001
address-family ipv4 unicast
neighbor 192.168.1.2 route-map rule_2 in
exit-address-family
bgp as-path access-list RULE permit ^65
route-map rule_2 permit 10
set as-path replace as-path-access-list RULE 6000
```
BGP routing table entry for 10.10.10.10/32, version 13
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
192.168.10.65
65000 1 2 3 123
192.168.10.65 from 192.168.10.65 (10.10.10.11)
Origin IGP, metric 0, valid, external, best (First path received)
```
After:
```
do show ip bgp 10.10.10.10/32
BGP routing table entry for 10.10.10.10/32, version 15
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
192.168.10.65
6000 1 2 3 123
192.168.10.65 from 192.168.10.65 (10.10.10.11)
Origin IGP, metric 0, valid, external, best (First path
received)
```
Signed-off-by: Francois Dumontet <francois.dumontet@6wind.com>
Add this logic inside bgp_capability_send() instead of repeating the whole
logic before calling bgp_capability_send().
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When setting local-role for the neighbor, force sending ROLE capability via
dynamic capability if it's enabled.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
vtysh is not supposed to show empty interface node in running config,
however the corresponding check is broken and empty nodes are shown.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
isis_snmp.test_isis_snmp/r1/ldpd.log:2023/08/04 12:49:54 LDP: [SHWNK-NWT5S][EC 100663304] No such command on config line 8: agentx
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
babel_topo1.test_babel_topo1/r3/babeld.log:2023/08/04 12:46:55 BABELD: [SHWNK-NWT5S][EC 100663304] No such command on config line 17: redistirbute ipv6 connected
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
./config_timing.test_config_timing/r1/zebra.log:2023/08/04 12:34:29 ZEBRA: [SHWNK-NWT5S][EC 100663304] No such command on config line 7: exit-route-map
./config_timing.test_config_timing/r1/zebra.log:2023/08/04 12:34:29 ZEBRA: [SHWNK-NWT5S][EC 100663304] No such command on config line 10: exit-route-map
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
./bfd_ospf_topo1.test_bfd_ospf_topo1/rt3/ospfd.log:2023/08/04 12:46:58 OSPF: [SHWNK-NWT5S][EC 100663304] No such command on config line 28: passive interface lo
./bfd_ospf_topo1.test_bfd_ospf_topo1/rt5/ospfd.log:2023/08/04 12:46:59 OSPF: [SHWNK-NWT5S][EC 100663304] No such command on config line 27: passive interface lo
./bfd_ospf_topo1.test_bfd_ospf_topo1/rt1/ospfd.log:2023/08/04 12:46:56 OSPF: [SHWNK-NWT5S][EC 100663304] No such command on config line 30: passive interface lo
./bfd_ospf_topo1.test_bfd_ospf_topo1/rt4/ospfd.log:2023/08/04 12:47:00 OSPF: [SHWNK-NWT5S][EC 100663304] No such command on config line 27: passive interface lo
./bfd_ospf_topo1.test_bfd_ospf_topo1/rt2/ospfd.log:2023/08/04 12:46:57 OSPF: [SHWNK-NWT5S][EC 100663304] No such command on config line 28: passive interface lo
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The test was reading in the bgp config for the isis config and
clearly the test is working without this. So let's remove
from the test the usage of isisd
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When displaying the configuration, the order of nexthop-vrf is wrong,
because the default VRF is not displayed, but still compared as the word
"default". Therefore it is placed in the middle of the list instead of
always being the first one.
Before the fix:
```
ip route 1.1.1.0/24 2.2.2.2 nexthop-vrf ccc
ip route 1.1.1.0/24 2.2.2.2
ip route 1.1.1.0/24 2.2.2.2 nexthop-vrf eee
```
After the fix:
```
ip route 1.1.1.0/24 2.2.2.2
ip route 1.1.1.0/24 2.2.2.2 nexthop-vrf ccc
ip route 1.1.1.0/24 2.2.2.2 nexthop-vrf eee
```
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add SRv6 Capabilities Sub-TLV to the Router Capabilities TLV in the LSPs
generated with the `lsp_build()` function.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
Add Codepoints for SRv6 Capabilities Sub-TLV, SRH Max SL MSD,
SRH Max End Pop MSD, SRH Max H.encaps MSD, SRH Max End D MSD
as per RFC 9352.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
Add Maximum SRv6 SID Depths (MSDs) parameters as per RFC 9352 section #4
to the per-area IS-IS SRv6 Data Base. Currently the MSD values are
hardcoded.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
`isis_srv6_area_term()` cleans up SRv6 information for a specific
IS-IS area. This commit adds a new function `isis_srv6_term()` that will
be used to perform global SRv6 cleanup.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
`isis_srv6_area_init()` initializes SRv6 information for a specific
IS-IS area. This commit adds a new function `isis_srv6_init()` that will
be used to perform global SRv6 initialization.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
When SRv6 is initialized on a given IS-IS area, set the administrative
enabled status to the default value defined by the YANG model.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
Add a boolean flag to indicate whether SRv6 is administratively enabled
on a given IS-IS area or not.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
Call `isis_srv6_area_term()` to cleanup the per-area SRv6 information
when an IS-IS area is terminated.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
Call `isis_srv6_area_init()` to initialize the per-area SRv6 DB when an
IS-IS area is created.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
