initially, that command was dumping only tables from default vrfs.
the change here consists in dumping all the tables from all the vrfs.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
the table identifier is made visible. this permits to easily know which
table identifier is dumped, or which table that entry belongs to, when
one calls 'show ip route all' command.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
this vty command explores the routing tables available, and dumps the
routing entries. there is no need to pass a table identifier, since all
configured tables are dumped.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Ashish Pant <ashish12pant@gmail.com>
frr-reolad.py invocation sends info message to stderror channel
Redirected stderror from frr-reload.py to stdout
Fixed verify_convergence when more than one link is present
Signed-off-by: Ashish Pant <ashish12pant@gmail.com>
Creates logdir everytime in start_topology, removed stop_topoloy.
Using tgen.stop_topology in test case now.
Signed-off-by: Ashish Pant <ashish12pant@gmail.com>
Example JSON and test cases for 3 types being added:
1. Single link between routers
2. Multiple linke between routers.
3. BGP session over loopback interface
Signed-off-by: Ashish Pant <ashish12pant@gmail.com>
Adds mulitple test scenarios for prefix-lists in bgp. Verfication
API for prefix-lits
Also adds description for bgp-basic test suite
Signed-off-by: Ashish Pant <ashish12pant@gmail.com>
Adding verify and config apis for bgp timer testcase
Adding verify and config apis for changing ASN to 4 bytes
Signed-off-by: Ashish Pant <ashish12pant@gmail.com>
Adding mulitple methods to form BGP configuration and other
helper methods.
If "bgp" is given in JSON the configuration will be created
Signed-off-by: Ashish Pant <ashish12pant@gmail.com>
Adds method to load configuration on the router. Save configuration
for resetting.
Adds method for configuring interfaces ip address on router.
Adds logdir and other pytest.ini option
Some code to cleanup bgp routemap.c a bit.
Addint to this, if a bgp flowspec entry contains a destination IP address,
then the ip address is compared against the prefix-list referenced into
the route-map used.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Donald Sharp <sharpd@cumulunetworks.com>
when multiple action rules are analysed in the BGP flowspec entry, if at
least the traffic-rate set to 0 is seen, then immediately create a rule
with drop rule. Previously this was not the case in case a forwarding
rule was seen.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
in addition to support for tcpflags, it is possible to filter on any
protocol. the filtering can then be based with iptables.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
pytest intends to deprecate users not having python 2 on the system.
in order to make topotest work, just use an older pytest version.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
zvni setup in zebra is controlled via bgpd i.e. advertise_all_vni
from bgpd triggers this setup. As a part of zvni creation we may need
to setup BUM mcast SG entries which are propagated to pimd for MDT setup.
Now pimd may not be present at the time of zvni creation or may restart
post zvni creation so we need a mechanism to replay (on pimd startup) and
to cleanup (on pimd stop). This is addressed via zebra_vxlan_sg_replay and
zebra_evpn_pim_cfg_clean_up.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
The callback itself might want to reschedule the resolver, so it is
useful to clear out the callback field before making the call instead of
after.
Signed-off-by: David Lamparter <equinox@diac24.net>
Unlike MRT dumps, BMP also provides packets sent by the router. Add
another hook for that.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The MRT dump code is already hooked in at the right places to write out
packets; the BMP code needs exactly the same access so let's make this
a hook.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Both of these hooks are necessary for proper operation of extensions
that need to latch on to a particular instance.
- without the delete hook, it's impossible to get rid of stale
references, leading to crashes with invalid instance pointers.
- the config-write hook is necessary because per-instance config needs
to be written inside the "router bgp" block to have the appropriate
context; adding a separate config node can't do that.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
BMP uses this to get notified about any changes to prefixes, at which
point it schedules its own processing to happen later.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
