When certain events occur (connected route changes e.g.)
zebra examines LSPs to see if they might have been affected. For
LSPs with backup nhlfes, skip this immediate processing and
wait for the owning protocol daemon to react.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
This commit introduces the implementation for the north-bound
callbacks for the zebra-specific route-map match and set clauses.
Signed-off-by: NaveenThanikachalam <nthanikachal@vmware.com>
Signed-off-by: Sarita Patra <saritap@vmware.com>
This is to fix the crash reproduced by the following steps:
* ip link add red type vrf table 1
Creates VRF.
* vtysh -c "conf" -c "vrf red"
Creates VRF NB node and marks VRF as configured.
* ip route 1.1.1.0/24 2.2.2.2 vrf red
* no ip route 1.1.1.0/24 2.2.2.2 vrf red
(or similar l3vni set/unset in zebra)
Marks VRF as NOT configured.
* ip link del red
VRF is deleted, because it is marked as not configured, but NB node
stays.
Subsequent attempt to configure something in the VRF leads to a crash
because of the stale pointer in NB layer.
Fixes#8357.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
EVPN nexthops are installed as remote neighs by zebra. This was earlier
done only via VRF IPvX uni routes imported from EVPN routes.
With EVPN-MH these VRF routes now reference a L3NHG which is setup based
on the EAD and doesn't include the RMAC. To workaround that BGP now
consolidates and maintains EVPN nexthops which are then sent to zebra.
zebra sets up these nexthops as L3-VNI nh entries using a dummy type-1
route as reference.
Ticket: CM-31398
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
This one also needed a bit of shuffling around, but MTYPE_RE is the only
one left used across file boundaries now.
Signed-off-by: David Lamparter <equinox@diac24.net>
Back when I put this together in 2015, ISO C11 was still reasonably new
and we couldn't require it just yet. Without ISO C11, there is no
"good" way (only bad hacks) to require a semicolon after a macro that
ends with a function definition. And if you added one anyway, you'd get
"spurious semicolon" warnings on some compilers...
With C11, `_Static_assert()` at the end of a macro will make it so that
the semicolon is properly required, consumed, and not warned about.
Consistently requiring semicolons after "file-level" macros matches
Linux kernel coding style and helps some editors against mis-syntax'ing
these macros.
Signed-off-by: David Lamparter <equinox@diac24.net>
The point of the `-std=gnu99` was to override a `-std=c99` that may be
coming in from net-snmp. However, we want C11, not C99.
Signed-off-by: David Lamparter <equinox@diac24.net>
Add a control and api for the use of backup nexthops in
recursive resolution. With 'no', we won't try to use installed
backup nexthops when resolving a recursive route.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Zebra routing tables are not controlled by the user and can not be
created/deleted manually. Current NB create/destroy callbacks are
incorrectly implemented because instead of creating/deleting the RIB
they are only checking for it's existence. YANG model should reflect
the real situation.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
There are places in the code where function nb_running_get_entry is used
with abort_if_not_found set to true during the config validation stage.
This is incorrect because when used in transactional CLI, the running
entry won't be set until the apply stage, and such usage leads to crash.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
like it has been done for iptable contexts, a zebra dplane context is
created for each ipset/ipset entry event. The zebra_dplane_ctx job is
then enqueued and processed by separate thread. Like it has been done
for zebra_pbr_iptable context, the ipset and ipset entry contexts are
encapsulated into an union of structures in zebra_dplane_ctx.
There is a specificity in that when storing ipset_entry structure, there
was a backpointer pointer to the ipset structure that is necessary
to get some complementary information before calling the hook. The
proposal is to use an ipset_entry_info structure next to the ipset_entry,
in the zebra_dplane context. That information is used for ipset_entry
processing. The ipset name and the ipset type are the only fields
necessary.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The iptable processing was not handled in remote dataplane, and was
directly processed by the thread in charge of zapi calls. Now that call
can be handled in the zebra_dplane separate thread. once a
zebra_dplane_ctx is allocated for iptable handling, the hook call is
performed later. Subsequently, a return code may be triggered to zclient
interface if any problem occurs when calling the hook call.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This was caused because of uninitialized netlint attrs in the bond-member
netlink parse API.
PS: It was caught by the upstream topotests on ARM8 (passed everywhere
else).
Signed-off-by: Anuradha Karuppiah <anuradhak@nvidia.com>
This is needed as kernel currently doesn't allow a mac replace if the dst
changes from a L2NHG to a single-VTEP and viceversa.
Ticket: CM-31561
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When a ES-bond is in bypass state MACs learnt on it are linked to the
access port instead of the ES. When LACP converges on the bond it moves
out of bypass and the MACs previously learnt on it are flushed to force
a re-learn on new traffic.
Ticket: CM-31326
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When an ES-bond comes out of bypass FRR needs to flush the local MACs learnt
while the bond was in bypass. To do that efficiently local MACs are linked
to the dest-access port. This only happens if the access-port is in
LACP-bypass or if it is non-ES.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Feature overview:
=================
A 802.3ad bond can be setup to allow lacp-bypass. This is done to enable
servers to pxe boot without a LACP license i.e. allows the bond to go oper
up (with a single link) without LACP converging.
If an ES-bond is oper-up in an "LACP-bypass" state MH treats it as a non-ES
bond. This involves the following special handling -
1. If the bond is in a bypass-state the associated ES is placed in a
bypass state.
2. If an ES is in a bypass state -
a. DF election is disabled (i.e. assumed DF)
b. SPH filter is not installed.
3. MACs learnt via the host bond are advertised with a zero ESI.
When the ES moves out of "bypass" the MACs are moved from a zero-ESI to
the correct non-zero id. This is treated as a local station move.
Implementation:
===============
When (a) an ES is detached from a hostbond or (b) an ES-bond goes into
LACP bypass zebra deletes all the local macs (with that ES as destination)
in the kernel and its local db. BGP re-sends any imported MAC-IP routes
that may exist with this ES destination as remote routes i.e. zebra can
end up programming a MAC that was perviously local as remote pointing
to a VTEP-ECMP group.
When an ES is attached to a hostbond or an ES-bond goes
LACP-up (out of bypss) zebra again deletes all the local macs in the
kernel and its local db. At this point BGP resends any imported MAC-IP
routes that may exist with this ES destination as sync routes i.e.
zebra can end up programming a MAC that was perviously remote
as local pointing to an access port.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
VNI configuration is done without NB layer in default VRF. It leads to
the following problems:
```
vtysh -c "conf" -c "vni 1"
vtysh -c "conf" -c "vrf default" -c "no vni"
```
Second command does nothing, because the NB node is not created by the
first command.
```
vtysh -c "conf" -c "vrf default" -c "vni 1"
vtysh -c "conf" -c "no vni 1"
```
Second command doesn't delete the NB node created by the first command.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This is causing problems with VM move i.e. transition from remote
neigh to local neigh. This transition involves changing the NUD_STATE
NUD_NOARP to NUD_STALE. And the weak override flag prevents changing
the state from connected (REACHABLE, NOARP, PERMANENT) to STALE.
PS: Weak-override was originally used to prevent race conditions where
FRR can end up making a REACHABLE neigh STALE. We may need to revisit
and address that case at a later point.
Ticket: CM-30273
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Start reorg of zebra nexthop-resolution so that we can use the
resolution logic for nexthop-groups as well as routes. Change
the signature of the core nexthop_active() api so that it does
not require a route-entry or route-node. Move some of the logic
around so that nexthop-specific logic is in nexthop_active(),
while route-oriented logic is in nexthop_active_check().
Signed-off-by: Mark Stapp <mjs@voltanet.io>
For MH the SVI MAC is advertised to prevent flooding of ARP replies.
But because of a bug the SVI MAC was being added to the zebra database
but not sent to bgpd for advertising.
Ticket: CM-33329
Signed-off-by: Anuradha Karuppiah <anuradhak@nvidia.com>
As a part of FRR shutdown interfaces are force flushed (in an arbitary
order). Interfaces are already down at that point i.e. resources like
SVI-MAC have already been released. Attempting to clean it up again
as a part of the force-flush was resulting in access of freed up memory -
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
==26457== Thread 1:
==26457== Invalid read of size 8
==26457== at 0x1AE6B0: zebra_evpn_acc_bd_svi_set (zebra_evpn_mh.c:606)
==26457== by 0x1B1460: zebra_evpn_if_cleanup (zebra_evpn_mh.c:1040)
==26457== by 0x13CA69: if_zebra_delete_hook (interface.c:244)
==26457== by 0x48A0E34: hook_call_if_del (if.c:59)
==26457== by 0x48A0E34: if_delete_retain (if.c:290)
==26457== by 0x48A2F94: if_delete (if.c:313)
==26457== by 0x48A3169: if_terminate (if.c:1217)
==26457== by 0x48E0024: vrf_delete (vrf.c:254)
==26457== by 0x48E0024: vrf_delete (vrf.c:225)
==26457== by 0x48E02FE: vrf_terminate (vrf.c:551)
==26457== by 0x1442E1: sigint (main.c:203)
==26457== by 0x1442E1: sigint (main.c:141)
==26457== by 0x48CF862: quagga_sigevent_process (sigevent.c:103)
==26457== by 0x48DD324: thread_fetch (thread.c:1404)
==26457== by 0x48A926A: frr_run (libfrr.c:1122)
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
(gdb) bt
(gdb) fr 5
1037 zebra/zebra_evpn_mh.c: No such file or directory.
(gdb) p zif->ifp->name
$2 = "vlan131", '\000' <repeats 12 times>
(gdb) p zif->link->info
$5 = (void *) 0x1
(gdb) p/x zif->ifp->flags
$7 = 0x1002
(gdb)
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Ticket: CM-32435
Signed-off-by: Anuradha Karuppiah <anuradhak@nvidia.com>
zebra crash is seen while cleaning up evpn interface
during shutdown event.
evpn interface clean up is called from vrf_delete callback
(gdb) frame 4
(is_up=false, br_zif=0x0, vlan_zif=0x557f31fb36f0) at zebra/zebra_evpn_mh.c:614
614 zebra/zebra_evpn_mh.c: No such file or directory.
(gdb) p tmp_br_zif
$1 = (struct zebra_if *) 0x0
(gdb) p vlan_zif->link
$2 = (struct interface *) 0x557f31fb2d40
(gdb) p vlan_zif->link->info
$3 = (void *) 0x0
(gdb) p zebra_if->ifp->name
No symbol "zebra_if" in current context.
(gdb) p vlan_zif->ifp->name
$4 = "peerlink-3.4094\000\000\000\000"
Ticket:CM-32435
Reviewed By:CCR-10957
Testing Done:
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Added support for advertising SVI MAC if EVPN-MH is enabled.
In the case of EVPN MH arp replies from an attached server can be sent to
the ES-peer. To prevent flooding of the reply the SVI MAC needs to be
advertised by default.
Note:
advertise-svi-ip could have been used as an alternate way to advertise
SVI MAC. However that config cannot be turned on if SVI IPs are
re-used (which is done to avoid wasting IP addresses in a subnet).
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
SVI IP is being advertised unconditionally i.e. even if disabled (and
that is the default config). This can be problematic when the SVI address
is re-used across racks.
Added the user config condition in all the relevant places where the
SVI advertisement is triggered.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When looking up the conversion from kernel protocol to
internal protocol family make sure we use the correct
AF_INET( what the kernel uses ) instead of AFI_IP (which
is what FRR uses ).
Routes from OSPF will show up from the kernel as OSPF6 instead of
OSPF. Which will cause mayhem
Ticket: CM-33306
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
