We need one struct eigrp_interface per ifp structure
not a ifp->info structure with a ei per connected.
Some minor code cleanup as well with macros and
their weird usage.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The EIGRP interface handling code created 2 levels
of interface information, the ei( created per *connected*
address?????) and the ifp->info pointer.
Start the combination of pushing these together and
cleaning up the weirdness that is these two data
structures.
This commit probably breaks eigrp's handling of
interfaces.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
maxage_lsa using prefix structure to store in route_table.
The lsa pointer is 4-8 bytes depending on arch, but prefix member field
would be 1 byte. Use ptr field of prefix structure to store lsa pointer.
Also memset to initialize to avoid crash on ARM platform as same LSA is
referenced from multiple times during shutdown of ospf.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
The zebra_ptm_finish() code was being called before the
client_list deletion. The client_list deletion is
attempting to call the ptm daemon and shut down the connection.
We should not be doing this *after* we shut down memory associated
with it as that we were writing into memory in random spots
in this case.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The adata pointer was not properly being set to
0 before being used. In addition notice malloc
failure and hard exit. If we have no memory on
startup something terrible has gone wrong and
we were going to crash shortly here anyways.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
While vertizes should be strictly ordered on insertion, deletion
will of course encouter equality.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Current cleanup is for unset values or variables that are not used anymore.
Regarding ospfd/ospf_vty.c: argv_find()
we'll never get it NULL, so get coststr = argv[idx]->arg;
If we are configuring a peer in multiple address families
and assigning the peer group valid configuration. If you
delay the non-automatically address family activation you
will not copy the peer group data into that peer.
Suppose we enter this:
router bgp 65001
bgp router-id 6.0.0.17
neighbor ISL peer-group
neighbor ISL advertisement-interval 0
neighbor ISL timers connect 5
neighbor ISL timers 3 10
address-family ipv4 unicast
neighbor ISL allowas-in 1
neighbor swp31s0 interface
neighbor swp31s0 peer-group ISL
address-family ipv6 unicast
neighbor ISL allowas-in 1
We've assigned allowas-in to the ISL peer group. Now suppose
we have a peer start connection to swp31s0. We startup and
auto copy the v4 peer group information onto the peer. We
do not copy the v6 peer group information because it has
not started yet.
Now at a later time if we enter:
address-family ipv6 unicast
neighbor ISL activate
We start the swp31s0 peer in v6, but we are not copying the
peer group data into the v6 swp31s0 peer data structure. As
such we are not respecting the v6 peer group config.
This Change modifies and renames the non_peergroup_activate_af
function to peer_activate_af. We also call the function
peer_group2peer_config_copy_af if the peer is part of a peer
group.
The static function peer_group2peer_config_copy_af I have moved
to higher up so we don't have to add a static function declaration
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The word Multiplier has been abbreviated to 'Mul' in
the output. This apparently is causing people
angst. Write word out.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Turn on '-g3 and -O0' for compilation. Additionally
document the --enable-dev-build flag in our documentation.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Preexisting code to detect commands targeted at wrong instance didn't
work because a command applied to a disconnected vtysh_client counted as
a successful run overriding wrong instance error message
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When displaying the mroute table, add ability to fill
in all the missing data that for human eyes can be assumed.
This will allow people using grep over the command
can get more information.
sharpd@robot ~> sudo vtysh -c "show ip mroute fill"
Source Group Proto Input Output TTL Uptime
* 229.1.1.1 STATIC dum0 enp3s0 1 00:11:07 Default-IP-Routing-Table
* 229.1.1.1 STATIC dum0 virbr0 1 00:01:47 Default-IP-Routing-Table
sharpd@robot ~>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
when warning about daemons that are not running, make sure to handle the
multi instance case
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
