When a route imported from l3vpn is analysed, the nexthop from default
VRF is looked up against a valid MPLS path. Generally, this is done on
backbones with a MPLS signalisation transport layer like LDP. Generally,
the BGP connection is multiple hops away. That scenario is already
working.
There is case where it is possible to run L3VPN over GRE interfaces, and
where there is no LSP path over that GRE interface: GRE is just here to
tunnel MPLS traffic. On that case, the nexthop given in the path does not
have MPLS path, but should be authorized to convey MPLS traffic provided
that the user permits it via a configuration command.
That commit introduces a new command that can be activated in route-map:
> set l3vpn next-hop encapsulation gre
That command authorizes the nexthop tracking engine to accept paths that
o have a GRE interface as output, independently of the presence of an LSP
path or not.
A configuration example is given below. When bgp incoming vpnv4 updates
are received, the nexthop of NLRI is 192.168.0.2. Based on nexthop
tracking service from zebra, BGP knows that the output interface to reach
192.168.0.2 is r1-gre0. Because that interface is not MPLS based, but is
a GRE tunnel, then the update will be using that nexthop to be installed.
interface r1-gre0
ip address 192.168.0.1/24
exit
router bgp 65500
bgp router-id 1.1.1.1
neighbor 192.168.0.2 remote-as 65500
!
address-family ipv4 unicast
no neighbor 192.168.0.2 activate
exit-address-family
!
address-family ipv4 vpn
neighbor 192.168.0.2 activate
neighbor 192.168.0.2 route-map rmap in
exit-address-family
exit
!
router bgp 65500 vrf vrf1
bgp router-id 1.1.1.1
no bgp network import-check
!
address-family ipv4 unicast
network 10.201.0.0/24
redistribute connected
label vpn export 101
rd vpn export 444:1
rt vpn both 52:100
export vpn
import vpn
exit-address-family
exit
!
route-map rmap permit 1
set l3vpn next-hop encapsulation gre
exit
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
For IPv4 matching, we have "match ip next-hop address A.B.C.D".
For IPv6 matching, we have "match ipv6 next-hop X:X::X:X".
To have consistency, let's add "address" keyword to IPv6 commands.
Old commands are preserved as hidden for backward compatibility.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
```
exit1-debian-9(config-route-map)# match ip route-source prefix-list ?
<cr>
PREFIXLIST_NAME IP prefix-list name
p1 p2
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
To ensure this, add a const modifier to functions' arguments. Would be
great do this initially and avoid this large code change, but better
late than never.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
There's no more difference between number-named and word-named access-lists.
This commit removes separate arguments for number-named ACLs from CLI.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
There is a possibility that the same line can be matched as a command in
some node and its parent node. In this case, when reading the config,
this line is always executed as a command of the child node.
For example, with the following config:
```
router ospf
network 193.168.0.0/16 area 0
!
mpls ldp
discovery hello interval 111
!
```
Line `mpls ldp` is processed as command `mpls ldp-sync` inside the
`router ospf` node. This leads to a complete loss of `mpls ldp` node
configuration.
To eliminate this issue and all possible similar issues, let's print an
explicit "exit" at the end of every node config.
This commit also changes indentation for a couple of existing exit
commands so that all existing commands are on the same level as their
corresponding node-entering commands.
Fixes#9206.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Will be handy to filter BGP prefixes by using BGP community alias
instead of numerical community values.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
- Add following set clause for route-maps
"set evpn gateway-ip <ipv4|ipv6 >A.B.C.D|X:X::X:X"
- When this route-map is applied as outboubd policy in BGP, it will set the
gateway-ip in BGP attribute For EVPN type-5 routes.
Example configuration:
route-map RMAP-EVPN_GWIP permit 5
set evpn gateway-ip ipv4 50.0.2.12
set evpn gateway-ip ipv6 50:0:2::12
router bgp 101
bgp router-id 10.100.0.1
neighbor 10.0.1.2 remote-as 102
!
address-family l2vpn evpn
neighbor 10.0.1.2 activate
neighbor 10.0.1.2 route-map RMAP-EVPN_GWIP out
advertise-all-vni
exit-address-family
Signed-off-by: Ameya Dharkar <adharkar@vmware.com>
Currently we have a "route-map optimization" command which is entered
from inside the route-map entry but actually applies to the whole
route-map. In addition, this command is not shown in the running-config
and not stored to the startup-config during "write".
Let's add a new command on the config node level to control this setting
and show it in the running-config to make possible to save it during
"write".
The old command is saved for the backward compatibility but hidden and
marked as deprecated.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This commit introduces the changes to the library route-map
north-bound callback implementation in order to align it to
the modified yang definitions.
Signed-off-by: NaveenThanikachalam <nthanikachal@vmware.com>
Signed-off-by: Sarita Patra <saritap@vmware.com>
Changed negating set metric route-map command to be usable in
conjunction with the affirming command.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
The "set metric" command wasn't processing metric additions and
subtractions (using + and -) correctly. Fix those problems.
Also, remove the "+metric" and "-metric" options since they don't
work and don't make any sense (they could be interpreted as unitary
increments/decrements but that was never supported).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When using the default CLI mode, the northbound layer needs to create
a separate transaction to process each YANG-modeled command since
they are supposed to be applied immediately (there's no candidate
configuration nor the "commit" command like in the transactional
CLI). The problem is that configuration transactions have an overhead
associated to them, in big part because of the use of some heavy
libyang functions like `lyd_validate()` and `lyd_diff()`. As of
now this overhead is substantial and doesn't scale well when large
numbers of transactions need to be performed in sequence.
As an example, loading 50k prefix-lists using a single transaction
takes about 2 seconds on a modern CPU. Loading the same 50k
prefix-lists using 50k transactions can take more than an hour
to complete (which is unacceptable by any standard). To fix this
problem, some heavy optimization work needs to be done on libyang and
on the FRR northbound itself too (e.g. perform partial configuration
diffs whenever possible). This, however, should be a long term
effort since these optimizations shouldn't be trivial to implement
and we're far from having the performance numbers we need.
In the meanwhile, this commit introduces a simple but efficient
workaround to alleviate the issue. In short, a new back-off timer
was introduced in the CLI to monitor and detect when too many
YANG-modeled commands are being received at the same time. When
a certain threshold is reached (100 YANG-modeled commands within
one second), the northbound starts to group all subsequent commands
into a single large transaction, which allows them to be processed
much faster (e.g. seconds and not hours). It's essentially a
protection mechanism that creates dynamically-sized transactions
when necessary to prevent performance issues from happening. This
mechanism is enabled both when parsing configuration files and when
reading commands from a terminal.
The downside of this optimization is that, if several YANG-modeled
commands are grouped into the same transaction and at least one of
them fails, the whole transaction is rejected. This is undesirable
since users don't expect transactional behavior when that's not
enabled explicitly. To minimize this issue, the CLI will log all
commands that were rejected whenever that happens, to make the
user aware of what happened and have enough information to fix
the problem. Commands that fail due to parsing errors or CLI-level
validations in general are rejected separately.
Again, this proposed workaround is intended to be temporary. The
goal is to provided a quick fix to issues like #6658 while we work
on better long-term solutions.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
DEFPY_YANG will allow the CLI to identify which commands are
YANG-modeled or not before executing them. This is going to be
useful for the upcoming configuration back-off timer work that
needs to commit pending configuration changes before executing a
command that isn't YANG-modeled.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Merge the cisco style access list with zebra's logic so we can mix both
types of rules while keeping the commands.
With this the cisco style limitation of having 'destination-*' only for
specific number ranges no longer exist for users of YANG/northbound (the
CLI still has this limitation).
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
And again for the name. Why on earth would we centralize this, just so
people can forget to update it?
Signed-off-by: David Lamparter <equinox@diac24.net>
Same as before, instead of shoving this into a big central list we can
just put the parent node in cmd_node.
Signed-off-by: David Lamparter <equinox@diac24.net>
There is really no reason to not put this in the cmd_node.
And while we're add it, rename from pointless ".func" to ".config_write".
[v2: fix forgotten ldpd config_write]
Signed-off-by: David Lamparter <equinox@diac24.net>
The only nodes that have this as 0 don't have a "->func" anyway, so the
entire thing is really just pointless.
Signed-off-by: David Lamparter <equinox@diac24.net>
Adapt the zebra route map code to use the transaction CLI output (e.g.
the CLI show callbacks) instead of the fallback compatibility.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
vtysh should handle going back up one level to try the command, there is
no need to be able to recurse inside route-map.
This also fixes a problem with northbound hitting the XPath queue limit
of 8 nodes.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Allow old CLI users to still print their configuration without migrating
to northbound.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
