It is possible that the if_lookup_by_index() call will return
a NULL value and calling zclient_send_interface_radv_req. Just
test that we have a valid interface pointer.
Found by Coverity
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Modify the import-check command to require the underlying prefix
to exist in the rib. General consensus is that this is the correct
behavior.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem reported that in many circumstances, RAs created in the
process of bringing up numbered IPv6 peers with extended-nexthop
capability enabled (for ipv4 over ipv6) were not stopped on the
interface when those peers were deleted. Found several circumstances
where this occurred and fix them in this patch.
Ticket: CM-26875
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
These are easy to get subtly wrong, and doing so can cause
nondeterministic failures when racing in parallel builds.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Issue:
Configuring default-originate when static default route is previously
advertised results in withdrawal of the route.
Fix :
Delete the adj-out entry for the previously advertised static
default route without sending explicit withdraw message.
Signed-off-by: kssoman <somanks@gmail.com>
the nlri flowspec above 240 bytes size was not handled.
Over 240 bytes, the length is 2 bytes length, and a calculation must be
done to obtain the real length. This commit handles it appropriately.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
- Fix 1 byte overflow when showing GR info in bgpd
- Use PATH_MAX for path buffers
- Use unsigned specifiers for uint16_t's in zebra pbr
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Replace sprintf with snprintf where straightforward to do so.
- sprintf's into local scope buffers of known size are replaced with the
equivalent snprintf call
- snprintf's into local scope buffers of known size that use the buffer
size expression now use sizeof(buffer)
- sprintf(buf + strlen(buf), ...) replaced with snprintf() into temp
buffer followed by strlcat
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When we receive an UPDATE with MP_NEXTHOP len as 32 bytes, we shouldn't
check if the global (1st) nexthop is unspecified.
Peering between bird and FRRouting we receive from Bird something like:
```
rcvd UPDATE w/ attr: , origin i, mp_nexthop ::(fe80::a00:27ff:fe09:f8a3)
```
The link-local (2nd) nexthop is valid and validated later in the code.
Before it was marked:
```
IPv6 unicast -- DENIED due to: martian or self next-hop;
```
After it's a valid prefix:
```
spine1-debian-9# show bgp
BGP table version is 0, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 65002
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
2a02:4780::/64 fe80::a00:27ff:fe09:f8a3
0 65001 i
Displayed 1 routes and 1 total paths
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Replace all `random()` calls with a function called `frr_weak_random()`
and make it clear that it is only supposed to be used for weak random
applications.
Use the annotation described by the Coverity Scan documentation to
ignore `random()` call warnings.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
In real world sometimes happens that bgp_nexthop_cache is NULL. Avoid
segfaulting when using `show [ip] bgp ...` CLI commands.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Rather than doing a f*gly hack for the RPKI code, let's do an on-exit
hook in cmd_node. Also allows replacing some special-casing in the vty
code.
Signed-off-by: David Lamparter <equinox@diac24.net>
And again for the name. Why on earth would we centralize this, just so
people can forget to update it?
Signed-off-by: David Lamparter <equinox@diac24.net>
Same as before, instead of shoving this into a big central list we can
just put the parent node in cmd_node.
Signed-off-by: David Lamparter <equinox@diac24.net>
There is really no reason to not put this in the cmd_node.
And while we're add it, rename from pointless ".func" to ".config_write".
[v2: fix forgotten ldpd config_write]
Signed-off-by: David Lamparter <equinox@diac24.net>
The only nodes that have this as 0 don't have a "->func" anyway, so the
entire thing is really just pointless.
Signed-off-by: David Lamparter <equinox@diac24.net>
The problem is when using kinda such topologies:
(192.168.1.1/32) r1 <-- eBGP --> r2 <-- iBGP --> r3
Looking at r3's nexthop for 192.168.1.1/32 we have it as r2, but really
it MUST be r1.
Checking if the nexthop is connected solves the problem even for cases
when route-reflectors are used.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
This fixes unnecessary whitespaces and makes capitalization
match for route type help strings.
Signed-off-by: Trey Aspelund <taspelund@cumulusnetworks.com>
Some competitive vendors like Cisco, Bird, OpenBGPD,
Nokia already have this by default enabled.
The list is here: https://github.com/bgp/RFC8212
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
