Adding header files changes where structure to hold
received graceful restart info from client is defined.
Also there are changes for show commands where exisiting
commands are extended.
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Soman K S <somanks@vmware.com>
Signed-off-by: Santosh P K <sapk@vmware.com>
For Graceful restart clients have to send GR capabilities
library functions are added to encode capabilities and
also for zebra to decode client capabilities.
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Soman K S <somanks@vmware.com>
Signed-off-by: Santosh P K <sapk@vmware.com>
Add a config that disables use of kernel-level nexthop ids.
Currently, zebra always uses nexthop ids if the kernel supports
them.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Two of the evpn show commands with json option has memory leak.
1) show bgp l2vpn evpn route vni all json
2) show bgp l2vpn evpn route esi json
Before fix:
----------
Executed 'show bgp l2vpn evpn route vni all json' multiple times
used ordinary blocks continue to increase.
Note at the time of show command capture there were 22 evpn routes
in vni evpn route table.
Memory statistics for bgpd:
System allocator statistics:
Total heap allocated: 9152 KiB
Holding block headers: 0 bytes
Used small blocks: 0 bytes
Used ordinary blocks: 7300 KiB
Free small blocks: 1760 bytes
Free ordinary blocks: 1852 KiB
Ordinary blocks: 880
Small blocks: 51
Holding blocks: 0
Ticket:CM-27920
Reviewed By:
Testing Done:
After fix:
---------
Executed 'show bgp l2vpn evpn route vni all json' multiple times
Used ordinary blocks remains low.
Memory statistics for bgpd:
System allocator statistics:
Total heap allocated: 8356 KiB
Holding block headers: 0 bytes
Used small blocks: 0 bytes
Used ordinary blocks: 6492 KiB
Free small blocks: 1840 bytes
Free ordinary blocks: 1864 KiB
Ordinary blocks: 939
Small blocks: 52
Holding blocks: 0
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Found memory leak in json output of evpn's route
commands.
After executing 'show bgp l2vpn evpn route type prefix json'
and 'show bgp l2vpn evpn route type macip json' few times
(6 times) with more than 600 routes in total seeing
memory footprint for bgpd continue to grow.
Memory statistics for bgpd:
System allocator statistics:
Total heap allocated: 12 MiB
Holding block headers: 0 bytes
Used small blocks: 0 bytes
Used ordinary blocks: 8390 KiB
Free small blocks: 1760 bytes
Free ordinary blocks: 3762 KiB
Ordinary blocks: 1161
Small blocks: 51
Holding blocks: 0
Ticket:CM-27920
Testing Done:
After fix:
excute few times,
'show bgp l2vpn evpn route type prefix json'
and 'show bgp l2vpn evpn route type macip json'
commands where used ordinary blocks (uordblks) is
in steady state.
Memory statistics for bgpd:
System allocator statistics:
Total heap allocated: 9968 KiB
Holding block headers: 0 bytes
Used small blocks: 0 bytes
Used ordinary blocks: 6486 KiB
Free small blocks: 1984 bytes
Free ordinary blocks: 3482 KiB
Ordinary blocks: 1110
Small blocks: 54
Holding blocks: 0
Memory statistics for bgpd:
System allocator statistics:
Total heap allocated: 10100 KiB
Holding block headers: 0 bytes
Used small blocks: 0 bytes
Used ordinary blocks: 6488 KiB
Free small blocks: 1984 bytes
Free ordinary blocks: 3612 KiB
Ordinary blocks: 1113
Small blocks: 54
Holding blocks: 0
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Add a 'copy' cli that reads a file into the current running
config. Add an entry about the new cli to the user doc.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
This change list contains the documentation of BGP Greacful Restart
feature and all the commnads to enable/disable the feature
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
* While the Deferral timer is running, signal route update pending
(ZEBRA_CLIENT_ROUTE_UPDATE_PENDING) from BGPD to Zebra.
* After expiry of the Deferral timer, the deferred routes are processed.
When the deferred route_list becomes empty, End-of-Rib is send to the
peer and route processing complete message (ZEBRA_CLIENT_ROUTE_UPDATE_COMPLETE)
is sent to Zebra. So that Zebra would delete any stale routes still
present in the rib.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
* Added CLI commands to update rib-stale-time, running in
Cmd : "bgp gaceful-restart rib-stale-time (1-3000)".
Cmd : "no bgp gaceful-restart rib-stale-time".
* Integrating the hooks function for signalling from BGPD
to ZEBRA to ZEBRA to enable or disable GR feature in ZEBRA
depending on bgp per peer gr configuration.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
*Adding helper caller hooks function for signalling from BGPD
to ZEBRA to enable or disable GR feature in ZEBRA depending
on bgp per peer gr configuration.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
*Adding helper function for signalling from BGPD to ZEBRA to
enable or disable GR feature in ZEBRA depending on bgp per
peer gr configuration.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
These changes are for Zebra lib in order to supportGraceful Restart
feature. These changes are addedtemporarily, until Zebra Graceful
Restart lib Pr is merged.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
Signed-off-by: Soman K S <somanks@vmware.com>
Data Structures, function declaration and Macros forSignalling
from BGPD to ZEBRA to enable or disable GR feature in ZEBRA
depending on bgp per peer gr configuration.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
*After a restarting router comes up and the bgp session is
successfully established with the peer. If the restarting
router doesn’t have any route to send, it send EOR to
the peer immediately before receiving updates from its peers.
*Instead the restarting router should send EOR, if the
selection deferral timer is not running OR count of eor received
and eor required are matches then send EOR.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
BGP disable EOR sending is a useful command for testing various
scenarios of BGP graceful restart.
* Added the hidden CLI command : bgp graceful-restart disable-eor
* The CLI will not be displayed in "show running-config" and will not
be stored in configuration file.
* When enabled, EOR will not be sent to peer
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
Signed-off-by: Soman K S <somanks@vmware.com>
When the peer router's gr mode had changed from helper/restart
to disable. The local bgp gr router should reset the peer
router's restart-time stored.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
bgp tcp connection.
When the BGP peer is configured between two bgp routes both routers would create
peer structure , when they receive each other’s open message. In this event both
speakers, open duplicate TCP sessions and send OPEN messages on each socket
simultaneously, the BGP Identifier is used to resolve which socket should be closed.
If BGP GR is enabled the old tcp session is dumped and the new session is retained.
So while this transfer of connection is happening, if all the bgp gr config
is not migrated to the new connection, the new bgp gr mode will never get applied.
Fix Summary:
1. Replicate GR configuration from the old session to the new session in bgp_accept().
2. Replicate GR configuration from stub to full-fledged peer in bgp_establish().
3. Disable all NSF flags, clear stale routes (if present), stop restart & stale timers
(if they are running) when the bgp GR mode is changed to “Disabled”.
4. Disable R-bit in cap, if it is not set the received open message.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
BGP GR Neighbor mode is showing the default string as “NotRecieved”,
as the bgp gr neighbour capability was not processed,
since the local mode is “Disable”.
However now it would be changed to “NotApplicable”.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
& GR is enabled.
When GR with deferral is enabled and connected routes are
distributed then in one race condition route node gets added
in to both deferred queue and work queue. If deferred queue
gets processed first then it ends up delete only flag while
leaving the entry in the work queue as it is. When a new update
comes for the same route node next time from peer then it hits
assert. Assert check is added to ensure we don’t add to work queue
again while it is already present.
So, check before adding in to deferred queue if it is already present
in work queue and bail if so.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
* Changing GR mode on a router needs a session reset from the
SAME router to negotiate new GR capability.
* The present GR implementation needs a session reset after every
new BGP GR mode change.
* When BGP session reset happens due to sending or receiving BGP
notification after changing BGP GR mode, there is no need of
explicit session reset.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
* BGP GR Neighbour mode in show command would show as
“NotApplicable”, when local mode is “Disable”. As the bgp
gr neighbour capability was not processed, since the local mode
is “Disable”.
* Minor changes in show Selection Deferral Time.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
* Selection Deferral Timer for Graceful Restart.
* Added selection deferral timer handling function.
* Route marking as selection defer when update message is received.
* Staggered processing of routes which are pending best selection.
* Fix for multi-path test case.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
and DS.
* Added config commands and data structures for deferral timer
configuration and processing.
Cmd : bgp graceful-restart select-defer-time (0-3600)
Cmd : no bgp graceful-restart select-defertime (0-3600)
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
Signed-off-by: Soman K S <somanks@vmware.com>
* Added new show command to show the graceful restart
information for each neighbor.
Cmd: show bgp [<ipv4|ipv6>] neighbors [<A.B.C.D|X:X::X:X|WORD>] graceful-restart
* Changes to show neighbors commands for displaying
graceful restart information.
Cmd :show [ip] bgp [<view|vrf> VIEWVRFNAME] [<ipv4|ipv6>] neighbors [<A.B.C.D|X:X::X:X|
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
* Changes to the capability sending function to advertise
graceful restart capability in the bgp OPEN message.
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
* Added FSM for peer and global configuration for graceful restart
* Added debug option BGP_GRACEFUL_RESTART for logs specific to
graceful restart processing
Signed-off-by: Biswajit Sadhu <sadhub@vmware.com>
Recent commit: 0eb97b860d
Broke onlink behavior and as a result ospf unnumbered failed
to work. This commit adds a small test to create 2 ospf routers,
connect them through ospf unlinked behavior and then ensure
that the routes are installed into the kernel as expected.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
commit: 0eb97b860d
Removed this chunk of code in zebra:
- if (ifp)
- if (connected_is_unnumbered(ifp))
- SET_FLAG(nexthop->flags, NEXTHOP_FLAG_ONLINK);
Effectively if we had a NEXTHOP_TYPE_IPV4_IFINDEX we would
auto set the onlink flag. This commit dropped it for some reason.
Add it back in an intelligent manner.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
