There is no need to check for failure of a ALLOC call
as that any failure to do so will result in a assert
happening. So we can safely remove all of this code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
show evpn mac vni all
show evpn mac vni x
does not display local svi and anycast mac into count.
Ticket:CM-20456
Testing Done:
Before:
TOR1# show evpn mac vni 1008
Number of MACs (local and remote) known for this VNI: 4
MAC Type Intf/Remote VTEP VLAN
44:38:39:00:6b:4c local vlan1008 1008
00:02:00:00:00:04 local hostbond5 1008
00:02:00:00:00:02 local hostbond4 1008
00:00:5e:00:01:01 local vlan1008-v0 1008
00:02:00:00:00:0c remote 27.0.0.15
00:02:00:00:00:0a remote 27.0.0.15
dell-s6000-07#
After:
TOR1# show evpn mac vni 1008
Number of MACs (local and remote) known for this VNI: 6
MAC Type Intf/Remote VTEP VLAN
44:38:39:00:6b:4c local vlan1008 1008
00:02:00:00:00:04 local hostbond5 1008
00:02:00:00:00:02 local hostbond4 1008
00:00:5e:00:01:01 local vlan1008-v0 1008
00:02:00:00:00:0c remote 27.0.0.15
00:02:00:00:00:0a remote 27.0.0.15
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
EVPN ND ext community support NA flag R-bit, to have proxy ND.
Set R-bit in EVPN NA if a given router is default gateway or there is a
local
router attached, which can be determine based on local neighbor entry.
Implement BGP ext community attribute to generate and parse R-bit and
pass along zebra to program neigh entry in kernel.
Upon receiving MAC/IP update with community type 0x06 and sub_type 0x08,
pass the R-bit to zebra to program neigh entry.
Set NTF_ROUTER in neigh entry and inform kernel to do proxy NA for EVPN.
Ref:
https://tools.ietf.org/html/draft-ietf-bess-evpn-na-flags-01
Ticket:CM-21712, CM-21711
Reviewed By:
Testing Done:
Configure Local vni enabled L3 Gateway, which would act as router,
checked
show evpn arp-cache vni x ip <ip of svi> on originated and remote VTEPs.
"Router" flag is set.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
SVI interface ip/hw address is advertised by the GW VTEP (say TORC11) with
the default-GW community. And the rxing VTEP (say TORC21) installs the GW
MAC as a dynamic FDB entry. The problem with this is a rogue packet from a
server with the GW MAC as source can cause a station move resulting in
TORC21 hijacking the GW MAC address and blackholing all inter rack traffic.
Fix is to make the GW MAC "sticky" pinning it to the GW VTEP (TORC11). This
commit does it by installing the FDB entry as static if the MACIP route is
received with the default-GW community (mimics handling of
mac-mobility-with-sticky community)
Sample output with from TORC12 with TORC11 setup as gateway -
root@TORC21:~# net show evpn mac vni 1004 mac 00:00:5e:00:01:01
MAC: 00:00:5e:00:01:01
Remote VTEP: 36.0.0.11 Remote-gateway Mac
Neighbors:
45.0.4.1
fe80::200:5eff:fe00:101
2001:fee1:0:4::1
root@TORC21:~# bridge fdb show |grep 00:00:5e:00:01:01|grep 1004
00:00:5e:00:01:01 dev vx-1004 vlan 1004 master bridge static
00:00:5e:00:01:01 dev vx-1004 dst 36.0.0.11 self static
root@TORC21:~#
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Ticket: CM-21508
New version of clang are detecting function parameters that we should
not be casting as such. Fix these issues.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we have a host prefix, actually free the alloced memory
associated with it when we free it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Add centralized thread scheduling dispatchers for client threads and
the main thread
* Rename everything in zserv.c to stop using a combination of:
- zebra_server_*
- zebra_*
- zserv_*
Everything in zserv.c now begins with zserv_*.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The neighbor host_list is expensive as well. Modify
the code to take advantage of a rb_tree as well.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We are going to modify more host_list's to host_rb's
so let's rename some functions to take advantage of
what is there.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The host_list when we attempt to use it at scale, ends
up spending a non-trivial amount of time finding and
sorting entries for the host list. Convert to a rb tree.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We have a command to enable symmetric routing only for type-5 routes.
This command is provided under vrf <> option in zebra as follows:
vrf <VRF>
vni <VNI> [prefix-routes-only]
We need the corresponding no version of the command as well as follows:
vrf <VRF>
no vni <VNI> [prefix-routes-only]
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
For ipv6 host, the next hop is conevrted to ipv6 mapped address.
However, the remote rmac should still be programmed with the ipv4 address.
This is how the entries will look in the kernel for ipv6 hosts routing.
vrf routing table:
ipv6 -> ipv6_mapped remote vtep on l3vni SVI
neigh table:
ipv6_mapped remote vtep -> remote RMAC
bridge fdb:
remote rmac -> ipv4 vtep tunnel
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Ensure that when EVPN routes are installed into zebra, the router MAC
is passed per next hop and appropriately handled. This is required for
proper multipath operation.
Ticket: CM-18999
Reviewed By:
Testing Done: Verified failed scenario, other manual tests
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
EVPN owns the remote neigh entries which are programed in the kernel.
This entries should not age out and the only way to delete should be
from EVPN. We should program these entries with NUD_NOARP instead of
NUD_REACHABLE to avoid aging of this macs.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
There can be a race condition between kernel and frr as follows.
Frr sends remote neigh notification.
At the (almost) same time kernel might send a notification saying
neigh is local.
After processing this notifications, the state in frr is local while
state in kernel is remote. This causes kernel and frr to be out of sync.
This problem will be avoided if FRR acts on the kernel notifications for
remote neighbors. When FRR sees a remote neighbor notification for a
neighbor which it thinks is local, FRR will change the neigh state to remote.
Ticket: CM-19923/CM-18830
Review: CCR-7222
Testing: Manual
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
[zebra/zebra_vxlan.c:5779] -> [zebra/zebra_vxlan.c:5778]:
(warning) Either the condition 'if(svi_if_zif&&svi_if_link)'
is redundant or there is possible null pointer dereference: svi_if_zif.
Signed-off-by: Ilya Shipitsin <chipitsine@gmail.com>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Nobody uses it, but it's got the same definition. Move the parser
function into zclient.c and use it.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Group send and receive functions together, change handlers to take a
message instead of looking at ->ibuf and ->obuf, allow zebra to read
multiple packets off the wire at a time.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
A lot of the handler functions that are called directly from the ZAPI
input processing code take different argument sets where they don't need
to. These functions are called from only one place and all have the same
fundamental information available to them to do their work. There is no
need to specialize what information is passed to them; it is cleaner and
easier to understand when they all accept the same base set of
information and extract what they need inline.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
All of the ZAPI message handlers return an integer that means different
things to each of them, but nobody ever reads these integers, so this is
technical debt that we can just eliminate outright.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Asymmetric routing is an ideal choice when all VLANs are cfged on all leafs.
It simplifies the routing configuration and
eliminates potential need for advertising subnet routes.
However, we need to reach the Internet or global destinations
or to do subnet-based routing between PODs or DCs.
This requires EVPN type-5 routes but those routes require L3 VNI configuration.
This task is to support EVPN type-5 routes for prefix-based routing in
conjunction with asymmetric routing within the POD/DC.
It is done by providing an option to use the L3 VNI only for prefix routes,
so that type-2 routes (host routes) will only use the L2 VNI.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
is_vni_l3 was removed as a part of PR1700. However, it seems to be used in master.
Causing the breakage. Made the changes to not use the API anymore.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
removed an additional field 'local-tunnel-ip' from l2vnis o/p
Ticket: CM-19670
Review: CCR-7167
Testing: Verified that the output is proper
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Currently, while processing kernel messages related to VNIs
we first check if VNI is L3 - this is a hash lookup
later, we do the lookup again to find the L3-VNI.
This is non-optimal.
Made changed to make sure we only do the lookup once.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Refine the notion of what FRR considers as "configured" VRF. It is no longer
based on user just typing "vrf FOO" but when something is actually configured
against that VRF. Right now, in zebra, the only configuration against a VRF
are static IP routes and EVPN L3 VNI. Whenever a configuration is removed,
check and clear the "configured" flag if there is no other configuration for
this VRF. When user attempts to configure a static route and the VRF doesn't
exist, a VRF is created; the VRF is only active when also defined in the
kernel.
Updates: 8b73ea7bd479030418ca06eef59d0648d913b620
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-10139, CM-18553
Reviewed By: CCR-7019
Testing Done:
1. Manual testing for L3 VNI and static routes - FRR restart, networking
restart etc.
2. 'vrf' smoke
<DETAILED DESCRIPTION (REPLACE)>
