Problem reported that if a bgp neighbor had a bfd timer change
made in frr.conf and systemctl reload frr performed, the neighbor
with the timer changed bounced. If the change is made in vtysh
by just adding the new timer values, no peer bounce occurs. This
fix skips the delete part of the delete/add process in frr-reload
so the peers stay up.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
RFC 5881 Section 4 tells us that the BFD source port must be between
49152 and 65535 inclusive.
Spotted by Lucian Cristian.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Solve issue #4032
- Change MPLS-TE from global to per Area
- Add new mpls_te_area structure to area in replacement of global variable
isisMPLS_TE
- Move mpls-te from global to instance in frr-isisd.yang
- Change code in isis_te.c, isis_northbound.c, isis_cli.c, isis_pdu.c,
isis_lsp.c and isis_zebra.c accordingly
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
The alias/description of an interface in linux was being
used to override the internal description. As such let's
fix the display to keep track of both if we have it.
Config in FRR:
!
interface docker0
description another combination
!
interface enp3s0
description BAMBOOZLE ME WILL YOU
!
Config in linux:
sharpd@robot ~/f/zebra> ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
alias This is the loopback you cabbage
2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 74:d0:2b:9c:16:eb brd ff:ff:ff:ff:ff:ff
alias HI HI HI
Now the 'show int descr' command:
robot# show int description
Interface Status Protocol Description
docker0 up down another combination
enp3s0 up up BAMBOOZLE ME WILL YOU
HI HI HI
lo up up This is the loopback you cabbage
Fixes: #4191
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ralph has kindly granted us GPLv2+ license to use this documentation,
and requests that we keep a reference to his name. Add these facts to
the documentation.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
So when we remove a ifchannel from the system we should check to
see if we still care about the S,G having it in the OIL still
due to inheritance rules. The deletion does not necessarily
mean it should not be in the OIL for the S,G.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Prevent IPv6 routes received via a ibgp session with one of its own interface
ip as nexthop from getting installed in the BGP table.
Implemented IPV6 HASH table, where we need to add any ipv6 address as they
gets configured and delete them from the HASH table as the ipv6 addresses
get unconfigured. The above hash table is used to verify if any route learned
via BGP has nexthop which is equal to one of its its connected ipv6 interface.
Signed-off-by: Biswajit Sadhu sadhub@vmware.com
the json code has not been updated since a variety of new flags have
been added to the code base. Add those flags in so we can tell
what is going on sometimes.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The PIM-EVPN doc was not rendering very well on the
website. So Update documentation to allow it to render
better.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the ability to select on a S or G for a `show ip mroute`
command.
show ip mroute 225.1.1.111
show ip mroute 4.5.6.7 225.1.1.111
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Always when creating a new S,G state look at all possible ifchannels
to decide what the mroute should be.
The bug that this is fixing is this:
Suppose two incoming `*,G` joins on swp1, and swp2.
Now suppose that one of those ifchannel `*,G` sends a `*,G S,G RPT Prune`.
We were creating the S,G upstream state as we should but we were
only looking at the S,G ifchannel to decide the S,G mroute we would
be creating. As such what we need to do is to look over the associated
*,G ifchannels and allow us to associate correct oil needed.
Ticket: CM-24732
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Reflow to 80 columns
* Improve markup
* Add --apiserver option to example ospfd invocations
* Add note on requirement of this option to use api server
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Start using the dataplane for interface-address programming,
on netlink platforms. Other platforms just stubbed at this
point.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Fixup in response to Jafar's review comments.
This is actually old code moved in from pimd to lib. But the fixup does
make sense.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
