this flag can be used when one routing daemon wants to force his route
to be injected prioritary with other routes, including selected routes.
for that, do not forget to update the new_selected pointer in the zebra
nexthop tracking algorithm.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The handlers for a couple of the main LSP-oriented zapi
messages explicitly limited themselves to a single out-label.
Allow multiple labels if the sender ... sends them.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
We made the decision to explicitly trust kernel and system routes
of every other type with 058c16b7e2.
So, we should trust directly connected routes the same way, assuming
the interface exists.
Old Behavior:
K 2.2.2.1/32 [0/0] is directly connected, unknown inactive, 00:00:39
New Behavior:
K>* 2.2.2.1/32 [0/0] is directly connected, test1, 00:00:03
As a bonus, this fixes the issues we were seeing with not removing
directly connected routes of certain interface types when
those interfaces go down/are deleted.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
It's been a year search and destroy.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Embed nexthop-group, which is just a pointer, in the zebra
nexthop-hash-entry object, rather than mallocing one.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
When a client connects to zebra with GR capabilities and
then restarts, it might disconnect again even before hello is
sent leading zebra cores.
GR should be supported only for dynamic neighbor who are capable
of restarting.
Signed-off-by: Santosh P K <sapk@vmware.com>
Somewhat gnarly code flow here that might be leaking memory - can't tell
if it's a test artifact or not, but in any case this reduces the
situations in which we need to alloc a block.
And we don't need to check XCALLOC for success...
And we don't need to null check before XFREE...
Or set XFREE'd pointers to NULL...
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Add in a few missing stub route-advert functions; these are
needed to build frr with v6 route adverts disabled.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
As part of checksum calculation for a received packet we were
comparing the checksum returned from in_cksum. Typically
when we calculate the checksum the value stored in the checksum
must be all 0's. Store the received checksum and then set
the checksum to 0 and then compare.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In several places we would send debug messages for failure situations
that really should be errors.
Signed-off-by: Donald Sharpd <sharpd@cumulusnetworks.com>
Using SO_BROADCAST, in the linux kernel, requires a uint32_t to be passed
in for all SOL_SOCKET calls. Modify code to use it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Use the zapi_nexthop struct with the mpls_labels
zapi messages instead of the special-purpose (and
more limited) nexthop struct that was being used.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
RFC 4861 states that ipv6 RA messages sent out an interface should
contain all global ipv6 addresses on that interface. This fix adds
that capability. To override the default flags and timer settings
for a particular prefix, the existing "ipv6 nd prefix ..." command
should be used via vtysh under the appropriate interface.
Ticket: CM-20363
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Today vtysh can show the ip/ip6 routes through several commands:
- show_route_cmd
- show_route_detail_cmd
- show_route_summary_cmd
- show_route_table_cmd
- show_route_table_vrf_cmd
- show_route_all_table_vrf_cmd
Each command has its own set of filter rules:
- show_route_cmd can filter by vrf, protocol, tag, ... but not by table
- show_route_table_cmd always filter by table
- show_route_table_vrf_cmd always filter by table and can filter by vrf
too
- show_route_all_table_vrf_cmd show all route in any table for a vrf (or
all)
To reduce the number of commands and provide a possibility to filter by
any key add possibility for the show_route_cmd to filter by table with a
specific value or all to get route in all tables.
Then the show_route_table_cmd, show_route_table_vrf_cmd and
show_route_all_table_vrf_cmd functions can be removed as they are covered
by the generic show_route_cmd function.
It is to be noted that when zebra is started by default, it is possible
to execute show ip route command with both vrf and table parameters,
whereas before the command was not displayed. This is due to the fact
that this combination is only permitted when zebra is launched with vrf
network namespace mode. There, if zebra is configured with vrf-lite
backend, then a vty error message informs the user that the combination
of both table and vrf is not possible.
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
The existing behavior is when a remote VTEP is deleted,
its associatedneighbor (arp) and MAC entries are removed from
zebra database and do not wait for explicit type-2 route
withdraw from originating VTEP.
Remote type-2 route delete checks if VTEP is present before
removing the entry.
The behavior works fine when all evpn routes points to the
same nexthop as the VTEP IP.
In MLAG topology with advertise-pip, self type-2 and type-5 routes
are advertised with individual VTEP IP as nexthop ip for the route.
When a new VNI is created, it is assigned individual IP as tunnel-ip
then it transition to anycast IP (of the MLAG). During the transition,
type-3 route (VTEP delete) withdraw is sent for the individual IP.
The remote VTEP delete should not trigger to remove evpn routes pointing
to VTEP IP. Instead the route will be removed via explicit withdraw.
Ticket:CM-27752
Reviewed By:CCR-9722
Testing Done:
In evpn with MLAG deployment with advertise-pip and advertise-svi-ip
enabled, validated remote vtep delete does not remove self type-2 routes
from zebra DB. Upon explicit type-2 withdraw routes are removed.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
