RFC 3623 specifies the Graceful Restart enhancement to the OSPF
routing protocol. This PR implements support for the restarting mode,
whereas the helper mode was implemented by #6811.
This work is based on #6782, which implemented the pre-restart part
and settled the foundations for the post-restart part (behavioral
changes, GR exit conditions, and on-exit actions).
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ospf`
EXEC-level command needs to be issued before restarting the ospfd
daemon (there's no specific requirement on how the daemon should
be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospfd is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
domainname is a merge conflict: it is duplicated, so delete it.
bgp content is a compille warning and wrongly display, so fix it.
Signed-off-by: anlancs <anlan_cs@tom.com>
Adding the "clear ipv6 ospf6 command" . It resets
the ospfv3 datastructures and clears the database
as well as route tables. It resets the neighborship
by restarting the interface state machine.
If the user wants to change the router-id, this
command updates the router-id to the latest static
router-id and starts the neighbor formation with
the new router-id.
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
`log-filter WORD` was giving me a serious headache since it also matches
`log WORD` due to the way the CLI token handling works. This meant that
a mistyped `log something` command would silently be interpreted as a
filter string, causing me serious headscratching and WTFs until I
figured what was going on.
Remove this UX pitfall so noone else falls into it. (Since the command
was never saved to config, renaming it shouldn't cause trouble.)
[Also I apparently forgot to update the docs when I transferred this
over to the new zlog bits...]
TODO for a rainy day: since we collect all the CLI commands anyway, we
should warn somewhere for "2nd level ambiguous" commands like this.
Signed-off-by: David Lamparter <equinox@diac24.net>
These names are saved in current vtysh's memory, can't and needn't be saved into
configure file by watchfrr's 'vtysh -w`.
Signed-off-by: anlancs <anlan_cs@tom.com>
Add a terse option to show bgp summary to shorten output.
Do not show the following information about the BGP
instances: the number of RIB entries, the table version and the used memory.
The "terse" option can be used in combination with the "remote-as", "neighbor",
"failed" and "established" filters, and with the "wide" option as well.
Before patch:
ubuntu# show bgp summary remote-as 123456
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
% No matching neighbor
Total number of neighbors 5
After patch:
ubuntu# show bgp summary remote-as 123456 terse
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 1
% No matching neighbor
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
similarly to what was done for IS-IS in commit 01d43141, combine
the SRGB and SRLB commands for OSPF-SR, so that we can replace
overlapping ranges in one sweep change.
Also allow the range configuration to be stored before SR is enabled.
There is no reason why we should not - in fact that constraint meant
that we were always requesting the default label ranges regardless
of what we actually wanted to use.
Finally, update the topotests now that we do not need to refresh
the SRGB/SRLB/MSD after disabling SR. Note that the prefix-sid still
needs to be re-added.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
Modify VRF/view display in show bgp summary:
- to be more concise
- to display on which VRF/view no neighbor was found
Before patch:
ubuntu# show bgp vrf all summary
Instance default:
IPv4 Unicast Summary:
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary:
Instance private:
IPv4 Unicast Summary:
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found
% No BGP neighbors found
After patch:
ubuntu# show bgp vrf all summary
IPv4 Unicast Summary (VRF default):
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary (VRF default):
(...)
IPv4 Unicast Summary (VRF private):
(...)
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found in VRF default
% No BGP neighbors found in VRF private
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
"ip nht resolve-via-default" is currently placed in "Link Parameters
Commands" section. Add a separate section and missing IPv6 counterpart.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
