A test run should really fail if it cannot find the test data, rather
then reporting success (thus masking that it never ran). Fix the test to
find it data (probably broken with the port to meson) and make it fail
if it cannot find its data.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Rather then always assuming open() fails because of permission denied,
generate the GError code from the errno and add the related strerror to
the message. And ofcourse output the error message in debugging rather
then just ignoring it.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
The type of Dell dock gets used in the device GUID, so make that
mandatory for device enumeration to succeed. Only relying on the
synapticsmst plugin to be cold plugged after the dell plugin isn't
enough to ensure this.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
When hitting a failure during enumerating make sure remote control mode
is disabled again.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
4a036018 broke the callback progress by putting the wrong device type in.
23:34:11:0715 GLib-GObject invalid cast from 'SynapticsMSTDevice' to 'FuDevice'
23:34:11:0715 Fu fu_device_set_progress: assertion 'FU_IS_DEVICE (device)' failed
b6f79556 caused the device ID strings to change, which synaptics
MST plugin was relying upon.
Update to use metadata instead to communicate this information.
Switching to build in -werror in 4016c839a8
was not working properly. Adjust the CI builds to use --werror instead.
Also while doing this, enable -werror in clang builds.
This makes more sense; we're updating the device, not the plugin itself.
This also means we don't need to funnel everything through callbacks like
GFileProgressCallback and we can also update the state without adding an
explicit callback to each derived device type.
This allows us to show the devices in a GUI with a nice icon. Some of the icon
mappings are not perfect and I'll be asking the GNOME designers for some
additions to the icon specification.
Custom vendor icons can also be specified, and /usr/share/fwupd/icons would be
a good place to put them. If vendor icons are used they should show a physical
device with the branding, rather than just the vendor logo.
This is to help break the dependence on the Dell plugin during
initalization.
NOTE: there are corner cases that this plugin will no longer
detect Dell systems now, but these are expected to be rare.
Over the months the original meaning of ALLOW_OFFLINE and ALLOW_ONLINE have be
lost, and there is now a confusing mixture of uses in the source tree. With this
commit we make it clear the UPDATABLE flag is used to specify when the device is
updatable (e.g. from the desktop live session, or from the systemd offline
updates mode, or both) and the NEEDS_REBOOT flag lets us know when the update
is actually going to be done.
For instance, a UEFI UpdateCapsule can be *scheduled* from either the desktop
or from the update mode (but the latter would be a bit weird), but does require
a reboot. Some devices might only be updatable outside the live session, for
instance a hard drive update or a GPU update -- there's just too much going on
with a live session and we want to tightly control what's running during the
firmware flash.
This also means we don't have to "retry" the update when scheduling an update
that really can be scheduled whenever, but just requires a reboot to apply.
Automake and autoconf are impossible to fully understand and Meson now provides
everything we need for a much smaller, faster, and more understandable build.
See http://mesonbuild.com/ for more information.
This significantly speeds up the test suite.
They can't really be easily represented anyways in the test suite
since the devnode would have to change so much between steps.
Although the same payload is used for all 3 MST hubs in TB16 or WD15
it's possible this may change one day. Create separate GUID's for
all 3 different combinations by encoding the chip ID into the GUID
string.
Although WD15 and TB16 share a same payload today, this may not
be the case some day in the future. Use the fu-dell-common method
to determine the dock in use to build the GUID.
There was a lot of confusion about when remote control was turned
on or off leading to dsyfunctional cascade support.
This has been confirmed to work for querying and flashing both
VMM3320s in a Rugged Latitude 5414 + dock.
The synapticsmst-common.c file had some global state so that cascade devices
could use the device fd. This made the control flow error prone, and it meant
that the fd could be leaked trivially on any error path.
Moving the fd ownership to the device is the logical place for the control, and
means we can create "connections" to access the main device and the cascade
devices.
This fixes the warnings detected by Coverity.
