1. Since board ID in synapticsmst.quirk is different based upon how
the board ID is read, don't whitelist it in `write_firmware`
2. Allow using `--force` with `fwupdmgr` or `fwupdtool` to override
board ID check.
3. Allow using custom flag `ignore-board-id` to ignore board IDs.
This will be the default for EVB boards and can be used in the event
of a factory mistake as well.
4. Move the EVB board IDs into their own synapticsmst_evb.quirk.
This file will not be installed by default (So EVB boards are only
functional when manually installed).
This flag is intended for devices that the restart procedure will
be performed as part of a transactional update by an external
controller.
None of the currently supported devices need this flag.
Panamera is a newer MST chip with a different flash layout and
multiple MCU running and accessing SPI/EEPROM simultaneously.
The firmware update process has to be run separately for each
SPI/EEPROM region.
Signed-off-by: Ryan Chang <ryan.chang@synaptics.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
- Split up `synapticsmst_device_write_firmware` to smaller more manageable
chunks
- Use `FuDeviceLocker` to ensure that device is in a known state after
update is complete (both in success or failure scenarios)
- Retry the write process up to 10 times in case of DPCD update failures
- Wait for flash clear to settle before writing to EEPROM/SPI
As seen by recent testing this is not working every time.
Since e6cda81f we're now building GUIDs that represent all the possibilities
for shared parts so it's not important to set dock type.
If the dock information is available then show that in the device name
and restrict the GUIDs created.
If it's not available, then just create GUIDs for all known docks
Rather then always assuming open() fails because of permission denied,
generate the GError code from the errno and add the related strerror to
the message. And ofcourse output the error message in debugging rather
then just ignoring it.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
The type of Dell dock gets used in the device GUID, so make that
mandatory for device enumeration to succeed. Only relying on the
synapticsmst plugin to be cold plugged after the dell plugin isn't
enough to ensure this.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
When hitting a failure during enumerating make sure remote control mode
is disabled again.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
This significantly speeds up the test suite.
They can't really be easily represented anyways in the test suite
since the devnode would have to change so much between steps.
Although the same payload is used for all 3 MST hubs in TB16 or WD15
it's possible this may change one day. Create separate GUID's for
all 3 different combinations by encoding the chip ID into the GUID
string.
Although WD15 and TB16 share a same payload today, this may not
be the case some day in the future. Use the fu-dell-common method
to determine the dock in use to build the GUID.
There was a lot of confusion about when remote control was turned
on or off leading to dsyfunctional cascade support.
This has been confirmed to work for querying and flashing both
VMM3320s in a Rugged Latitude 5414 + dock.
The synapticsmst-common.c file had some global state so that cascade devices
could use the device fd. This made the control flow error prone, and it meant
that the fd could be leaked trivially on any error path.
Moving the fd ownership to the device is the logical place for the control, and
means we can create "connections" to access the main device and the cascade
devices.
This fixes the warnings detected by Coverity.
