Cairo 1.10 will sometimes generate trapezoids like this, so we can't
consider them invalid. Fixes bug 45009, reported by Michael Biebl.
This reverts commit 2437ae80e5.
When a trapezoid has a top/bottom that is above/below the left/right
edges, degenerate trapezoids become possible. For example the edge
could be very short and close to horizontal. If the bottom edge is far
below the bottom point of such a short edge, the result is that the
lower right corner of the trapezoid will be extremely far to the left.
This kind of trapezoid causes overflows in the rasterization code, so
change pixman_trapezoid_valid() to reject them.
In the macros for the PDF blend modes, two comp1_t variables are
multiplied together and then used as if the result were a
comp4_t. When comp1_t is a uint8_t, this is fine because they are
promoted to int, and the product of two uint8_ts fits in an
int. However, when comp1_t is uint16, the product does not necessarily
fit in an int, so casts are necessary.
Fix for bug 43906, reported by Siarhei Siamashka.
The upcoming optimization which is going to be able to replace BILINEAR filter
with NEAREST where appropriate needs to analyze the transformation matrix
and not to make any mistakes.
The changes to affine-test include:
1. Higher chance of using the same scale factor for x and y axes. This can help
to stress some special cases (for example the case when both x and y scale
factors are integer). The same applies to x/y translation.
2. Introduced a small chance for "corrupting" transformation matrix by flipping
random bits. This supposedly can help to identify the cases when some of the
fast paths or other code logic is wrongly activated due to insufficient checks.
The boxes used region_contains_test() sometimes overflow causing
*** BUG ***
In pixman_region32_union_rect: Invalid rectangle passed
Set a breakpoint on '_pixman_log_error' to debug
messages to be printed when pixman is compiled with DEBUG. Fix this by
dividing the x, y, w, h coordinates by 4 to prevent overflows.
On win32 the tests are built but they are not run automatically by the
build system.
A minimal 'check' target (depending on the tests being built) can
simply run them and log to the console their success/failure.
The win32 build system does not generate config.h and correctly runs
the compiler without defining HAVE_CONFIG_H. Nevertheless some files
include config.h without checking for its availability, breaking the
build from a clean directory:
test\utils.h(2) : fatal error C1083: Cannot open include file:
'config.h': No such file or directory
...
The win32 build system repeatedly defines some basic variables
(notably program names and flags) and C sources compilation rules.
They can be factored out to a common Makefile, to be included in every
other Makefile.win32.
Makefile.am and Makefile.win32 should not duplicate content, as this
leads to breaking the build when they are not kept in sync.
This can be avoided by listing sources, headers and common build
variables/rules in a Makefile.sources file.
In order to further simplify the test makefiles, the utility functions
are now in a static library, which gets linked to all the tests and
benchmarks.
Adding scaling-helpers-test to the testsuite on win32 makes MSVC
complain about int64_t being used as an expression:
scaling-helpers-test.c(27) : error C2275: 'int64_t' : illegal use of
this type as an expression
When debugging it is often very useful to be able to save an image as
a png file. This commit adds a function "write_png()" that does that.
If libpng is not available, then the function becomes a noop.
This test generates random regions and checks whether random boxes and
points are contained within them. The results are combined and a CRC32
value is computed and compared to a known-correct one.
The lcg_rand() function only returns 15 random bits, so lcg_rand_u32()
would always have 0 in bit 31 and bit 15. Fix that by calling
lcg_rand() three times, to generate 15, 15, and 2 random bits
respectively.
V2: Use the 10/11 most significant bits from the 3 lcg results and mix
them with the low ones from the adjacent one, as suggested by Andrea
Canciani.
Move the eight most common formats to the top of the list of image
formats and make create_random_image() much more likely to select one
of those eight formats.
This should help catch more bugs in SIMD optimized operations.
Previously, this function would do coordinate calculations in such a
way that (x_dst, y_dst) would only affect the alignment of the source
image, but not of the traps, which would always be considered to be in
absolute destination coordinates. This is unlike the
pixman_image_composite() function which also registers the mask to the
destination.
This patch makes it so that traps are also offset by (x_dst, y_dst).
Also add a comment explaining how this function is supposed to
operate, and update tri-test.c and composite-trap-test.c to deal with
the new semantics.
When run in PIXMAN_RANDOMIZE_TESTS mode, this test would go into an
infinite loop because the loop started at 'seed' but the stop
condition was still N_TESTS.
This patch makes so that composite and stress-test will start from a
random seed if the PIXMAN_RANDOMIZE_TESTS environment variable is
set. Running the test suite in this mode is useful to get more test
coverage.
Also, in stress-test.c make it so that setting the initial seed causes
threads to be turned off. This makes it much easier to see when
something fails.
Individual correctness check for the new bilinear scaling related
supplementary function. This test program uses a bit wider range
of input arguments, not covered by other tests.
MSVC does not notice non-returning functions (abort() / assert(0))
and warns about paths which end with them in non-void functions:
c:\cygwin\home\ranma42\code\fdo\pixman\test\fetch-test.c(114) :
warning C4715: 'reader' : not all control paths return a value
c:\cygwin\home\ranma42\code\fdo\pixman\test\stress-test.c(133) :
warning C4715: 'real_reader' : not all control paths return a value
c:\cygwin\home\ranma42\code\fdo\pixman\test\composite.c(431) :
warning C4715: 'calc_op' : not all control paths return a value
These warnings can be silenced by adding a return after the
termination call.
The Microsoft C compiler cannot handle subobject initialization and
Win32 does not provide snprintf.
Work around these limitations by using normal struct initialization
and using sprintf (a manual check shows that the buffer size is
sufficient).
This separates the test suite from the random gtk+ using test
programs. "demos" is somewhat misleading because the programs there
are not particularly exciting (with the possible exception of
composite-test which shows off all the compositing operators).
The next few commits will speed this up quite a bit.
Current output:
---
reference memcpy speed = 2217.5MB/s (554.4MP/s for 32bpp fills)
---
over_x888_8_0565 = L1: 54.67 L2: 54.01 M: 52.33 ( 18.88%) HT: 37.19 VT: 35.54 R: 29.40 RT: 13.63 ( 162Kops/s)
Green Hills Software MULTI compiler was producing a number
of warnings due to incorrect uses of int instead of the correct
corresponding pixman_*_t type.
radial-test is a port of the radial-gradient test from the cairo test
suite. It has been modified so that some pixels have 0 in both the a
and b coefficients of the quadratic equation solved by the rasterizer,
to expose a division by zero in the original implementation.
This option can be used for building fully static binaries of the test
programs so that they can be easily run using qemu-user. With binfmt-misc
configured, 'make check' works fine for crosscompiled pixman builds.
