Core & protocols
----------------
- Wrap datapath globals into net_aligned_data, to avoid false sharing.
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container).
- Add SO_INQ and SCM_INQ support to AF_UNIX.
- Add SIOCINQ support to AF_VSOCK.
- Add TCP_MAXSEG sockopt to MPTCP.
- Add IPv6 force_forwarding sysctl to enable forwarding per interface.
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB.
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users.
- Convert TCP send queue handling from tasklet to BH workque.
- Improve BPF iteration over TCP sockets to see each socket exactly once.
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code.
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel NAPI
thread when threaded NAPI gets disabled. Previously thread would stick
around until ifdown due to tricky synchronization.
- Allow multicast routing to take effect on locally-generated packets.
- Add output interface argument for End.X in segment routing.
- MCTP: add support for gateway routing, improve bind() handling.
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink.
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed.
- Support NUD_PERMANENT for proxy neighbor entries.
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM.
- Add sequence numbers to netconsole messages. Unregister netconsole's
console when all net targets are removed. Code refactoring.
Add a number of selftests.
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup.
- Support inspecting ref_tracker state via DebugFS.
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links.
- Allow providing upcall pid for the 'execute' command in openvswitch.
- Remove DCCP support from Netfilter's conntrack.
- Disallow multiple packet duplications in the queuing layer.
- Prevent use of deprecated iptables code on PREEMPT_RT.
Driver API
----------
- Support RSS and hashing configuration over ethtool Netlink.
- Add dedicated ethtool callbacks for getting and setting hashing fields.
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc.
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs.
- Support traffic classes in devlink rate API for bandwidth management.
- Remove rtnl_lock dependency from UDP tunnel port configuration.
Device drivers
--------------
- Add a new Broadcom driver for 800G Ethernet (bnge).
- Add a standalone driver for Microchip ZL3073x DPLL.
- Remove IBM's NETIUCV device driver.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is used
by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lqbe
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
Export irq_domain_free_irqs_top(), making it usable for drivers compiled as
modules.
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
irqdomain.c's kernel-doc exists, but is not plugged into Documentation/
yet.
Before plugging it in, fix it first: irq_domain_get_irq_data() and
irq_domain_set_info() were documented twice. Identically, by both
definitions for CONFIG_IRQ_DOMAIN_HIERARCHY and !CONFIG_IRQ_DOMAIN_HIERARCHY.
Therefore, switch the second kernel-doc into an ordinary comment -- change
"/**" to simple "/*". This avoids sphinx's: WARNING: Duplicate C
declaration
Next, in commit b7b377332b ("irqdomain: Fix the kernel-doc and plug it
into Documentation"), irqdomain.h's (header) kernel-doc was added into
core-api/genericirq.rst. But given the amount of irqdomain functions and
structures, move all these to core-api/irq/irq-domain.rst now.
Finally, add these newly fixed irqdomain.c's (source) docs there as
well.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-58-jirislaby@kernel.org
Most irq_domain_add_*() functions are unused now, so drop them. The
remaining ones are moved to the deprecated section and will be removed
during the merge window after the patches in various trees have been
merged.
Note: The Chinese docs are touched but unfinished. I cannot parse those.
[ tglx: Remove the leftover in irq-domain.rst and handle merge logistics ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-41-jirislaby@kernel.org
There is no reason to export the function as an extra symbol. It is
simple enough and is just a wrapper to already exported functions.
Therefore, switch the exported function to an inline.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-13-jirislaby@kernel.org
All uses of of_node_to_fwnode() in non-irqdomain code were changed to
"officially" defined of_fwnode_handle(). Therefore, the former can be
dropped along with the last uses in the irqdomain code.
Due to merge logistics the inline cannot be dropped immediately. Move it to
a deprecated section, which will be removed during the merge window.
[ tglx: Handle merge logistics ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-12-jirislaby@kernel.org
Add new function *_twothreecell() to extend support to parse three-cell
interrupts which encoded as <instance hwirq irqflag>, the translate
function will retrieve irq number and flag from last two cells.
This API will be used in gpio irq driver which need to work with
two or three cells cases.
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250326-04-gpio-irq-threecell-v3-1-aab006ab0e00@gentoo.org
Naming interrupt domains host is confusing at best and the irqdomain code
uses both domain and host inconsistently.
Therefore rename irq_get_default_host() to irq_get_default_domain().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-4-jirislaby@kernel.org
Naming interrupt domains host is confusing at best and the irqdomain code
uses both domain and host inconsistently.
Therefore rename irq_set_default_host() to irq_set_default_domain().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-3-jirislaby@kernel.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Cache the result of this function in a local variable in
order not to rely on CSE (common subexpression elimination). Prepare
for changing 'nr_irqs' from an exported global variable into a variable
with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-22-bvanassche@acm.org
The unification of irq_domain_create_legacy() missed the fact that
interrupts must be associated even when the Linux interrupt number provided
in the first_irq argument is 0.
This breaks all call sites of irq_domain_create_legacy() which supply 0 as
the first_irq argument.
Enforce the association for legacy domains in __irq_domain_instantiate() to
cure this.
[ tglx: Massaged it slightly. ]
Fixes: 70114e7f75 ("irqdomain: Simplify simple and legacy domain creation")
Reported-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/all/c3379142-10bc-4f14-b8ac-a46927aeac38@gmail.com
When the domain suffix is not supplied alloc_fwnode_name() unconditionally
adds a separator.
Fix the format strings to get rid of the stray '-' separator.
Fixes: 1e7c052925 ("irqdomain: Allow giving name suffix for domain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240812193101.1266625-3-andriy.shevchenko@linux.intel.com
The code uses if (bus_token) and if (bus_token == DOMAIN_BUS_ANY).
Since bus_token is an enum, the latter is more robust against changes.
Convert all !bus_token checks to explicitely check for DOMAIN_BUS_ANY.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240812193101.1266625-2-andriy.shevchenko@linux.intel.com
Devices can provide multiple interrupt lines. One reason for this is that
a device has multiple subfunctions, each providing its own interrupt line.
Another reason is that a device can be designed to be used (also) on a
system where some of the interrupts can be routed to another processor.
A line often further acts as a demultiplex for specific interrupts
and has it's respective set of interrupt (status, mask, ack, ...)
registers.
Regmap supports the handling of these registers and demultiplexing
interrupts, but the interrupt domain code ends up assigning the same name
for the per interrupt line domains. This causes a naming collision in the
debugFS code and leads to confusion, as /proc/interrupts shows two separate
interrupts with the same domain name and hardware interrupt number.
Instead of adding a workaround in regmap or driver code, allow giving a
name suffix for the domain name when the domain is created.
Add a name_suffix field in the irq_domain_info structure and make
irq_domain_instantiate() use this suffix if it is given when a domain is
created.
[ tglx: Adopt it to the cleanup patch and fixup the invalid NULL return ]
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/871q2yvk5x.ffs@tglx
irq_domain_set_name() is truly unreadable gunk. Clean it up before adding
more.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/all/874j7uvkbm.ffs@tglx
irq_domain_create_simple() and irq_domain_create_legacy() use
__irq_domain_instantiate(), but have extra handling of allocating interrupt
descriptors and associating interrupts in them. Some of that is duplicated.
There are also call sites which have conditonals to invoke different
interrupt domain creator functions, where one of them is usually
irq_domain_create_legacy(). Alternatively they associate the interrupts for
the legacy case after creating the domain.
Moving the extra logic of irq_domain_create_simple()/legacy() into
__irq_domain_instantiate() allows to consolidate that.
Introduce hwirq_base and virq_base members in the irq_domain_info
structure, which allows to transport the required information and add the
conditional interrupt descriptor allocation and interrupt association into
__irq_domain_instantiate().
This reduces irq_domain_create_legacy() and irq_domain_create_simple() to
trivial wrappers which fill in the info structure and allows call sites
which must support the legacy case along with more modern mechanism to
select the domain type via the parameters of the info struct.
[ tglx: Massaged change log ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/32d07bd79eb2b5416e24da9e9e8fe5955423dcf9.1723120028.git.mazziesaccount@gmail.com
This simplifies the handling of platform MSI and wire to MSI controllers
and removes about 500 lines of legacy code.
Aside of that it paves the way for ARM/ARM64 to utilize the dynamic
allocation of PCI/MSI interrupts and to support the upcoming non
standard IMS (Interrupt Message Store) mechanism on PCIe devices
-----BEGIN PGP SIGNATURE-----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=2adH
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2024-07-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI interrupt updates from Thomas Gleixner:
"Switch ARM/ARM64 over to the modern per device MSI domains.
This simplifies the handling of platform MSI and wire to MSI
controllers and removes about 500 lines of legacy code.
Aside of that it paves the way for ARM/ARM64 to utilize the dynamic
allocation of PCI/MSI interrupts and to support the upcoming non
standard IMS (Interrupt Message Store) mechanism on PCIe devices"
* tag 'irq-msi-2024-07-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip/gic-v3-its: Correctly fish out the DID for platform MSI
irqchip/gic-v3-its: Correctly honor the RID remapping
genirq/msi: Move msi_device_data to core
genirq/msi: Remove platform MSI leftovers
irqchip/irq-mvebu-icu: Remove platform MSI leftovers
irqchip/irq-mvebu-sei: Switch to MSI parent
irqchip/mvebu-odmi: Switch to parent MSI
irqchip/mvebu-gicp: Switch to MSI parent
irqchip/irq-mvebu-icu: Prepare for real per device MSI
irqchip/imx-mu-msi: Switch to MSI parent
irqchip/gic-v2m: Switch to device MSI
irqchip/gic_v3_mbi: Switch over to parent domain
genirq/msi: Remove platform_msi_create_device_domain()
irqchip/mbigen: Remove platform_msi_create_device_domain() fallback
irqchip/gic-v3-its: Switch platform MSI to MSI parent
irqchip/irq-msi-lib: Prepare for DOMAIN_BUS_WIRED_TO_MSI
irqchip/mbigen: Prepare for real per device MSI
irqchip/irq-msi-lib: Prepare for DEVICE MSI to replace platform MSI
irqchip/gic-v3-its: Provide MSI parent for PCI/MSI[-X]
irqchip/irq-msi-lib: Prepare for PCI MSI/MSIX
...
Modify the comment formatting in irq_find_matching_fwspec function to
enhance code readability and maintain consistency.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Shivamurthy Shastri <shivamurthy.shastri@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614102403.13610-2-shivamurthy.shastri@linutronix.de
Domain creation functions use __irq_domain_add(). With the introduction
of irq_domain_instantiate(), __irq_domain_add() becomes obsolete.
In order to fully remove __irq_domain_add(), convert domain
creation function to irq_domain_instantiate()
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-19-herve.codina@bootlin.com
The current API functions create an irq_domain and also publish this
newly created to domain. Once an irq_domain is published, consumers can
request IRQ in order to use them.
Some interrupt controller drivers have to perform some more operations
with the created irq_domain in order to have it ready to be used.
For instance:
- Allocate generic irq chips with irq_alloc_domain_generic_chips()
- Retrieve the generic irq chips with irq_get_domain_generic_chip()
- Initialize retrieved chips: set register base address and offsets,
set several hooks such as irq_mask, irq_unmask, ...
With the newly introduced irq_domain_alloc_generic_chips(), an interrupt
controller driver can use the irq_domain_chip_generic_info structure and
set the init() hook to perform its generic chips initialization.
In order to avoid a window where the domain is published but not yet
ready to be used, handle the generic chip creation (i.e the
irq_domain_alloc_generic_chips() call) before the domain is published.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-16-herve.codina@bootlin.com
The current API does not allow additional initialization before the
domain is published. This can lead to a race condition between consumers
and supplier as a domain can be available for consumers before being
fully ready.
Introduce the init() hook to allow additional initialization before
plublishing the domain. Also introduce the exit() hook to revert
operations done in init() on domain removal.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-13-herve.codina@bootlin.com
irq_domain_update_bus_token() is the only way to set the domain bus
token. This is sub-optimal as irq_domain_update_bus_token() can be called
only once the domain is created and needs to revert some operations, change
the domain name and redo the operations.
In order to avoid this revert/change/redo sequence, take the domain bus
into account token during the domain creation.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-12-herve.codina@bootlin.com
__irq_domain_create() can fail for several reasons. When it fails it
returns a NULL pointer and so filters out the exact failure reason.
The only user of __irq_domain_create() is irq_domain_instantiate() which
can return a PTR_ERR value. On __irq_domain_create() failure, it uses an
arbitrary error code.
Rather than using this arbitrary error value, make __irq_domain_create()
return is own error code and use that one.
[ tglx: Remove the pointless ERR_CAST. domain is a valid return pointer ]
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-11-herve.codina@bootlin.com
irq_domain_instantiate() handles all needs to be used in
irq_domain_create_hierarchy()
Avoid code duplication and use directly irq_domain_instantiate() for
hierarchy domain creation.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-10-herve.codina@bootlin.com
To use irq_domain_instantiate() from irq_domain_create_hierarchy(),
irq_domain_instantiate() needs to handle the domain hierarchy parent.
Add the required functionality.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-9-herve.codina@bootlin.com
In order to use irq_domain_instantiate() from several places such as
irq_domain_create_hierarchy(), irq_domain_instantiate() needs to handle
additional domain flags.
Add the required infrastructure.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-8-herve.codina@bootlin.com
The existing __irq_domain_create() use a bunch of parameters to create
an irq domain.
With the introduction of irq_domain_info structure, these parameters are
available in the information structure itself.
Using directly this information structure allows future flexibility to
add other parameters in a simple way without the need to change the
__irq_domain_create() prototype.
Convert __irq_domain_create() to use the information structure.
[ tglx: Fixup struct initializer ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-7-herve.codina@bootlin.com
The interrupt domain name computation and setting is directly done in
__irq_domain_create(). This leads to a quite long __irq_domain_create()
function.
In order to simplify __irq_domain_create() and isolate the domain name
computation and setting, move the related operations to a dedicated
function.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-6-herve.codina@bootlin.com
The existing irq_domain_add_*() functions used to instantiate an IRQ
domain are wrappers built on top of __irq_domain_add() and describe the
domain properties using a bunch of parameters.
Adding more parameters and wrappers to hide new parameters in the
existing code lead to more and more code without any relevant value and
without any flexibility.
Introduce irq_domain_instantiate() where the interrupt domain properties
are given using a irq_domain_info structure instead of the bunch of
parameters to allow flexibility and easy evolution.
irq_domain_instantiate() performs the same operation as the one done by
__irq_domain_add(). For compatibility reason with existing code, keep
__irq_domain_add() but convert it to irq_domain_instantiate().
[ tglx: Fixed up struct initializer coding style ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-3-herve.codina@bootlin.com
In preparation of the introduction of the irq domain instantiation,
introduce irq_domain_free() to avoid code duplication on later
modifications.
This new function is an extraction of the current operations performed
to free the irq domain. No functional change intended.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240614173232.1184015-2-herve.codina@bootlin.com
fwnode_handle_get(fwnode) is called when a domain is created with fwnode
passed as a function parameter. fwnode_handle_put(domain->fwnode) is called
when the domain is destroyed but during the creation a path exists that
does not set domain->fwnode.
If this path is taken, the fwnode get will never be put.
To avoid the unbalanced get and put, set domain->fwnode unconditionally.
Fixes: d59f6617ee ("genirq: Allow fwnode to carry name information only")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240614173232.1184015-4-herve.codina@bootlin.com
During compilation, several warning of the following form were raised:
Function parameter or struct member 'x' not described in 'yyy'
Add the missing function parameter descriptions.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240527161450.326615-10-herve.codina@bootlin.com
Improve the readability of irqdomain debugging information in debugfs by
printing the flags field of domain files as human-readable strings instead
of a raw bitmask, which aligned with the existing style used for irqchip
flags in the irq debug files.
Before:
#cat :cpus:cpu@0:interrupt-controller
name: :cpus:cpu@0:interrupt-controller
size: 0
mapped: 2
flags: 0x00000003
After:
#cat :cpus:cpu@0:interrupt-controller
name: :cpus:cpu@0:interrupt-controller
size: 0
mapped: 3
flags: 0x00000003
IRQ_DOMAIN_FLAG_HIERARCHY
IRQ_DOMAIN_NAME_ALLOCATED
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240529091628.3666379-1-ruanjinjie@huawei.com
It's a bit hard to read the logic since the virq is used before checking it
for 0. Rearrange the code to make it better to understand.
This, in particular, should clearly answer the question whether the caller
needs to perform this check or not, and there are plenty of places for both
variants, confirming a confusion.
Fun fact that the new code is shorter:
Function old new delta
irq_dispose_mapping 278 271 -7
Total: Before=11625, After=11618, chg -0.06%
when compiled by GCC on Debian for x86_64.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240405190105.3932034-1-andriy.shevchenko@linux.intel.com
Users of the IRQCHIP_PLATFORM_DRIVER_{BEGIN,END} helpers rely on a fwspec
containing only the fwnode (and crucially a number of parameters set to 0)
together with a DOMAIN_BUS_ANY token to check whether a parent irqchip has
probed and registered a domain.
Since de1ff306dc ("genirq/irqdomain: Remove the param count restriction
from select()"), ops->select() is called unconditionally, meaning that
irqchips implementing select() now need to handle ANY as a match.
Instead of adding more esoteric checks to the individual drivers, add that
condition to irq_find_matching_fwspec(), and let it handle the corner case,
as per the comment in the function.
This restores the functionality of the above helpers.
Fixes: de1ff306dc ("genirq/irqdomain: Remove the param count restriction from select()")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20240220114731.1898534-1-maz@kernel.org
Link: https://lore.kernel.org/r/20240219-gic-fix-child-domain-v1-1-09f8fd2d9a8f@linaro.org
Reroute interrupt allocation in irq_create_fwspec_mapping() if the domain
is a MSI device domain. This is required to convert the support for wire
to MSI bridges to per device MSI domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-13-apatel@ventanamicro.com
Now that the GIC-v3 callback can handle invocation with a fwspec parameter
count of 0 lift the restriction in the core code and invoke select()
unconditionally when the domain provides it.
Preparatory change for per device MSI domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-3-apatel@ventanamicro.com
irq_domain_debugfs_init() is defined in irqdomain.c, but the
declaration is in a header that is not included here:
kernel/irq/irqdomain.c:1965:13: error: no previous prototype for 'irq_domain_debugfs_init' [-Werror=missing-prototypes]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230516200432.554240-1-arnd@kernel.org
- Prevent possible NULL pointer derefences in irq_data_get_affinity_mask()
and irq_domain_create_hierarchy().
- Take the per device MSI lock before invoking code which relies
on it being hold.
- Make sure that MSI descriptors are unreferenced before freeing
them. This was overlooked when the platform MSI code was converted to
use core infrastructure and results in a fals positive warning.
- Remove dead code in the MSI subsystem.
- Clarify the documentation for pci_msix_free_irq().
- More kobj_type constification.
-----BEGIN PGP SIGNATURE-----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=jWot
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"A set of updates for the interrupt susbsystem:
- Prevent possible NULL pointer derefences in
irq_data_get_affinity_mask() and irq_domain_create_hierarchy()
- Take the per device MSI lock before invoking code which relies on
it being hold
- Make sure that MSI descriptors are unreferenced before freeing
them. This was overlooked when the platform MSI code was converted
to use core infrastructure and results in a fals positive warning
- Remove dead code in the MSI subsystem
- Clarify the documentation for pci_msix_free_irq()
- More kobj_type constification"
* tag 'irq-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, platform-msi: Ensure that MSI descriptors are unreferenced
genirq/msi: Drop dead domain name assignment
irqdomain: Add missing NULL pointer check in irq_domain_create_hierarchy()
genirq/irqdesc: Make kobj_type structures constant
PCI/MSI: Clarify usage of pci_msix_free_irq()
genirq/msi: Take the per-device MSI lock before validating the control structure
genirq/ipi: Fix NULL pointer deref in irq_data_get_affinity_mask()
Some polishing and small fixes for iommufd:
- Remove IOMMU_CAP_INTR_REMAP, instead rely on the interrupt subsystem
- Use GFP_KERNEL_ACCOUNT inside the iommu_domains
- Support VFIO_NOIOMMU mode with iommufd
- Various typos
- A list corruption bug if HWPTs are used for attach
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCY/TgzQAKCRCFwuHvBreF
Ya3AAP4/WxTJIbDvtTyH3Fae3NxTdO8j8gsUvU1vrRYG83zdnAEAxd1yii7GEO8D
crkeq9D4FUiPAkFnJ64Exw2FHb060Qg=
=RABK
-----END PGP SIGNATURE-----
Merge tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd
Pull iommufd updates from Jason Gunthorpe:
"Some polishing and small fixes for iommufd:
- Remove IOMMU_CAP_INTR_REMAP, instead rely on the interrupt
subsystem
- Use GFP_KERNEL_ACCOUNT inside the iommu_domains
- Support VFIO_NOIOMMU mode with iommufd
- Various typos
- A list corruption bug if HWPTs are used for attach"
* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
iommufd: Do not add the same hwpt to the ioas->hwpt_list twice
iommufd: Make sure to zero vfio_iommu_type1_info before copying to user
vfio: Support VFIO_NOIOMMU with iommufd
iommufd: Add three missing structures in ucmd_buffer
selftests: iommu: Fix test_cmd_destroy_access() call in user_copy
iommu: Remove IOMMU_CAP_INTR_REMAP
irq/s390: Add arch_is_isolated_msi() for s390
iommu/x86: Replace IOMMU_CAP_INTR_REMAP with IRQ_DOMAIN_FLAG_ISOLATED_MSI
genirq/msi: Rename IRQ_DOMAIN_MSI_REMAP to IRQ_DOMAIN_ISOLATED_MSI
genirq/irqdomain: Remove unused irq_domain_check_msi_remap() code
iommufd: Convert to msi_device_has_isolated_msi()
vfio/type1: Convert to iommu_group_has_isolated_msi()
iommu: Add iommu_group_has_isolated_msi()
genirq/msi: Add msi_device_has_isolated_msi()
The recent switch to per-domain locking caused a NULL dereference in
irq_domain_create_hierarchy(), as Xen code is calling
msi_create_irq_domain() with a NULL parent pointer.
Fix that by testing parent to be set before dereferencing it. For a
non-existing parent the irqdomain's root will stay to point to
itself.
Fixes: 9dbb8e3452 ("irqdomain: Switch to per-domain locking")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230223083800.31347-1-jgross@suse.com
Core:
- Move the interrupt affinity spreading mechanism into lib/group_cpus
so it can be used for similar spreading requirements, e.g. in the
block multi-queue code.
This also contains a first usecase in the block multi-queue code which
Jens asked to take along with the librarization.
- Improve irqdomain locking to close a number race conditions which
can be observed with massive parallel device driver probing.
- Enforce and document the semantics of disable_irq() which cannot be
invoked safely from non-sleepable context.
- Move the IPI multiplexing code from the Apple AIC driver into the
core. so it can be reused by RISCV.
Drivers:
- Plug OF node refcounting leaks in various drivers.
- Correctly mark level triggered interrupts in the Broadcom L2 drivers.
- The usual small fixes and improvements.
- No new drivers for the record!
-----BEGIN PGP SIGNATURE-----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=+pu3
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Move the interrupt affinity spreading mechanism into lib/group_cpus
so it can be used for similar spreading requirements, e.g. in the
block multi-queue code
This also contains a first usecase in the block multi-queue code
which Jens asked to take along with the librarization
- Improve irqdomain locking to close a number race conditions which
can be observed with massive parallel device driver probing
- Enforce and document the semantics of disable_irq() which cannot be
invoked safely from non-sleepable context
- Move the IPI multiplexing code from the Apple AIC driver into the
core, so it can be reused by RISCV
Drivers:
- Plug OF node refcounting leaks in various drivers
- Correctly mark level triggered interrupts in the Broadcom L2
drivers
- The usual small fixes and improvements
- No new drivers for the record!"
* tag 'irq-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interrupts
irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interrupts
irqdomain: Switch to per-domain locking
irqchip/mvebu-odmi: Use irq_domain_create_hierarchy()
irqchip/loongson-pch-msi: Use irq_domain_create_hierarchy()
irqchip/gic-v3-mbi: Use irq_domain_create_hierarchy()
irqchip/gic-v3-its: Use irq_domain_create_hierarchy()
irqchip/gic-v2m: Use irq_domain_create_hierarchy()
irqchip/alpine-msi: Use irq_domain_add_hierarchy()
x86/uv: Use irq_domain_create_hierarchy()
x86/ioapic: Use irq_domain_create_hierarchy()
irqdomain: Clean up irq_domain_push/pop_irq()
irqdomain: Drop leftover brackets
irqdomain: Drop dead domain-name assignment
irqdomain: Drop revmap mutex
irqdomain: Fix domain registration race
irqdomain: Fix mapping-creation race
irqdomain: Refactor __irq_domain_alloc_irqs()
irqdomain: Look for existing mapping only once
irqdomain: Drop bogus fwspec-mapping error handling
...
The IRQ domain structures are currently protected by the global
irq_domain_mutex. Switch to using more fine-grained per-domain locking,
which can speed up parallel probing by reducing lock contention.
On a recent arm64 laptop, the total time spent waiting for the locks
during boot drops from 160 to 40 ms on average, while the maximum
aggregate wait time drops from 550 to 90 ms over ten runs for example.
Note that the domain lock of the root domain (innermost domain) must be
used for hierarchical domains. For non-hierarchical domains (as for root
domains), the new root pointer is set to the domain itself so that
&domain->root->mutex always points to the right lock.
Also note that hierarchical domains should be constructed using
irq_domain_create_hierarchy() (or irq_domain_add_hierarchy()) to avoid
having racing allocations access a not fully initialised domain. As a
safeguard, the lockdep assertion in irq_domain_set_mapping() will catch
any offenders that also fail to set the root domain pointer.
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230213104302.17307-21-johan+linaro@kernel.org
