When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.
Fixes: fec9095bde "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() itself on
failure, so there is no need for the driver to also do this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 code to get the "peripheral" / "host" / "otg" IRQ first tries
platform_get_irq_byname() and then falls back to the IRQ at index 0 if
the platform_get_irq_byname().
In this case we do not want platform_get_irq_byname() to print an error
on failure, so switch to platform_get_irq_byname_optional() instead which
does not print an error.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205037
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing our host system using Microsoft's usb stack against our
gadget for various BESL values, we found an issue with their usb stack
when the recommended baseline BESL value is 0 (125us) or when the deep
BESL is 1 or less. The Windows host will issue a usb reset immediately
after it receives the extended BOS descriptor and the enumeration will
fail after a few attempts.
To keep compatibility with Microsoft's host usb stack, let's workaround
this issue by using the recommended baseline BESL of 1 (or 150us)
and clamp the deep BESL value within 2 to 15.
This was tested against Windows 10 build 18956.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating with LPM signals, the controller asserts the deep
low-power signal (utmi_l1_suspend_n) to the phy when the BESL value of
the LPM token is equal to or greater than DCTL.HIRD_Thres[3:0] (and
with DCTL.HIRD_Thres[4] set). Otherwise, the shallow low-power signal
(utmi_sleep_n) is asserted. Set the recommended deep BESL equal to the
controller's DCTL.HIRD_Thres[3:0] setting, and set the baseline BESL
to 0 for the shallow low-power signal. This maximizes the opportunity
for L1 residency and optimizes power savings.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->hird_threshold field should store "snps,hird_threshold" property
only and not a combination of multiple properties. Remove the value of
"snps,is-utmi-l1-suspend" property from the field dwc->hird_threshold.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts
commit 6a4290cc28 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.
Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.
Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.
Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.
Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.
This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The macro name DWC3_DCTL_LPM_ERRATA is uninformative and does not do
masking. Remove DWC3_DCTL_LPM_ERRATA_MASK and rename
DWC3_DCTL_LPM_ERRATA to DWC3_DCTL_NYET_THRES with proper masking.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All DWC3 controllers are LPM capable. Report that in the
usb_gadget.lpm_capable for the gadget driver to properly output the
bcdUSB value in the descriptor.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_gadget_suspend() is called under dwc->lock spinlock. In such context
calling synchronize_irq() is not allowed. Move the problematic call out
of the protected block to fix the following kernel BUG during system
suspend:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:112
in_atomic(): 1, irqs_disabled(): 128, pid: 1601, name: rtcwake
6 locks held by rtcwake/1601:
#0: f70ac2a2 (sb_writers#7){.+.+}, at: vfs_write+0x130/0x16c
#1: b5fe1270 (&of->mutex){+.+.}, at: kernfs_fop_write+0xc0/0x1e4
#2: 7e597705 (kn->count#60){.+.+}, at: kernfs_fop_write+0xc8/0x1e4
#3: 8b3527d0 (system_transition_mutex){+.+.}, at: pm_suspend+0xc4/0xc04
#4: fc7f1c42 (&dev->mutex){....}, at: __device_suspend+0xd8/0x74c
#5: 4b36507e (&(&dwc->lock)->rlock){....}, at: dwc3_gadget_suspend+0x24/0x3c
irq event stamp: 11252
hardirqs last enabled at (11251): [<c09c54a4>] _raw_spin_unlock_irqrestore+0x6c/0x74
hardirqs last disabled at (11252): [<c09c4d44>] _raw_spin_lock_irqsave+0x1c/0x5c
softirqs last enabled at (9744): [<c0102564>] __do_softirq+0x3a4/0x66c
softirqs last disabled at (9737): [<c0128528>] irq_exit+0x140/0x168
Preemption disabled at:
[<00000000>] (null)
CPU: 7 PID: 1601 Comm: rtcwake Not tainted
5.0.0-rc3-next-20190122-00039-ga3f4ee4f8a52 #5252
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c01110f0>] (unwind_backtrace) from [<c010d120>] (show_stack+0x10/0x14)
[<c010d120>] (show_stack) from [<c09a4d04>] (dump_stack+0x90/0xc8)
[<c09a4d04>] (dump_stack) from [<c014c700>] (___might_sleep+0x22c/0x2c8)
[<c014c700>] (___might_sleep) from [<c0189d68>] (synchronize_irq+0x28/0x84)
[<c0189d68>] (synchronize_irq) from [<c05cbbf8>] (dwc3_gadget_suspend+0x34/0x3c)
[<c05cbbf8>] (dwc3_gadget_suspend) from [<c05bd020>] (dwc3_suspend_common+0x154/0x410)
[<c05bd020>] (dwc3_suspend_common) from [<c05bd34c>] (dwc3_suspend+0x14/0x2c)
[<c05bd34c>] (dwc3_suspend) from [<c051c730>] (platform_pm_suspend+0x2c/0x54)
[<c051c730>] (platform_pm_suspend) from [<c05285d4>] (dpm_run_callback+0xa4/0x3dc)
[<c05285d4>] (dpm_run_callback) from [<c0528a40>] (__device_suspend+0x134/0x74c)
[<c0528a40>] (__device_suspend) from [<c052c508>] (dpm_suspend+0x174/0x588)
[<c052c508>] (dpm_suspend) from [<c0182134>] (suspend_devices_and_enter+0xc0/0xe74)
[<c0182134>] (suspend_devices_and_enter) from [<c0183658>] (pm_suspend+0x770/0xc04)
[<c0183658>] (pm_suspend) from [<c0180ddc>] (state_store+0x6c/0xcc)
[<c0180ddc>] (state_store) from [<c09a9a70>] (kobj_attr_store+0x14/0x20)
[<c09a9a70>] (kobj_attr_store) from [<c02d6800>] (sysfs_kf_write+0x4c/0x50)
[<c02d6800>] (sysfs_kf_write) from [<c02d594c>] (kernfs_fop_write+0xfc/0x1e4)
[<c02d594c>] (kernfs_fop_write) from [<c02593d8>] (__vfs_write+0x2c/0x160)
[<c02593d8>] (__vfs_write) from [<c0259694>] (vfs_write+0xa4/0x16c)
[<c0259694>] (vfs_write) from [<c0259870>] (ksys_write+0x40/0x8c)
[<c0259870>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed55ffa8 to 0xed55fff0)
...
Fixes: 01c10880d2 ("usb: dwc3: gadget: synchronize_irq dwc irq in suspend")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
-----BEGIN PGP SIGNATURE-----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=4fTL
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
Currently req->num_trbs is not reset after the TRBs are skipped and
processed from the cancelled list. The gadget driver may reuse the
request with an invalid req->num_trbs, and DWC3 will incorrectly skip
trbs. To fix this, simply reset req->num_trbs to 0 after skipping
through all of them.
Fixes: c3acd59014 ("usb: dwc3: gadget: use num_trbs when skipping TRBs on ->dequeue()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we're disabling the endpoint anyway, we don't worry about
getting endpoint command completion interrupt.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we modified the code to fix a race condition, it's clear that
DWC3_EP_END_TRANSFER_PENDING is unnecessary, considering that
DWC3_EP_TRANSFER_STARTED will remain set until End Transfer completes.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a rare race condition that may happen during a Disconnect
Interrupt if we have a started request that happens to be
dequeued *after* completion of End Transfer command. If that happens,
that request will be left waiting for completion of an End Transfer
command that will never happen.
If End Transfer command has already completed before, we are safe to
giveback the request straight away.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have a proper flag for testing that we have a valid transfer in
flight, let's use that instead.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We must wait until End Transfer completes in order to clear
DWC3_EP_TRANSFER_STARTED, otherwise we may confuse the driver.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For OUT endpoints, zero-length transfers require MaxPacketSize buffer as
per the DWC_usb3 programming guide 3.30a section 4.2.3.3.
This patch fixes this by explicitly checking zero length
transfer to correctly pad up to MaxPacketSize.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have req->status, we don't need this extra flag
anymore. It's safe to remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Queueing the same request twice can introduce hard-to-debug
problems. At least one function driver - Android's f_mtp.c - is known
to cause this problem.
While that function is out-of-tree, this is a problem that's easy
enough to avoid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch starts tracking dwc3_request status. A following patch will
build on top of this to prevent a request from being queued twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On v3.10a in dual-role mode, if port is in device mode
and gadget driver isn't loaded, the OTG event interrupts don't
come through.
It seems that if the core is configured to be OTG2.0 only,
then we can't leave the DCFG.DEVSPD at Super-speed (default)
if we expect OTG to work properly. It must be set to High-speed.
Fix this issue by configuring DCFG.DEVSPD to the supported
maximum speed at gadget init. Device tree still needs to provide
correct supported maximum speed for this to work.
This issue wasn't present on v2.40a but is seen on v3.10a.
It doesn't cause any side effects on v2.40a.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently the link_state is uninitialized and the default value is 0(U0)
before the first time we start the udc, and after we start the udc then
stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with
an undefined link_state:
WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
OUT endpoint requests may somtimes have this flag set when
preparing to be submitted to HW indicating that there is an
additional TRB chained to the request for alignment purposes.
If that request is removed before the controller can execute the
transfer (e.g. ep_dequeue/ep_disable), the request will not go
through the dwc3_gadget_ep_cleanup_completed_request() handler
and will not have its needs_extra_trb flag cleared when
dwc3_gadget_giveback() is called. This same request could be
later requeued for a new transfer that does not require an
extra TRB and if it is successfully completed, the cleanup
and TRB reclamation will incorrectly process the additional TRB
which belongs to the next request, and incorrectly advances the
TRB dequeue pointer, thereby messing up calculation of the next
requeust's actual/remaining count when it completes.
The right thing to do here is to ensure that the flag is cleared
before it is given back to the function driver. A good place
to do that is in dwc3_gadget_del_and_unmap_request().
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We see dwc3 endpoint stopped by unwanted irq during
suspend resume test, which is caused dwc3 ep can't be started
with error "No Resource".
Here, add synchronize_irq before suspend to sync the
pending IRQ handlers complete.
Signed-off-by: Bo He <bo.he@intel.com>
Signed-off-by: Yu Wang <yu.y.wang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
-----BEGIN PGP SIGNATURE-----
iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlwQ7sQdHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQbioA//fSpx5SV7undE1skG
lgjx7Uv2lqnU1kJxhTtyH54tZVhGMmaz4mDVJ3bRk4xotdh3BGQ7nRuui9PDGZmC
81bSjRBVvHXG0xtQQ1AjNc6vTf5h2MVRAZ4U2dp7pkNOgkoWQSakyH3Tz4Brhpfh
UWHLaVYrCb2R68b1pmQbJ6ckSkOu9Wt1yj3SJxvSOkRdbSgb9+khTNZJyyWuGort
zw6pcK33AuLwfOuz7qk8Wihqwi6BOgSrCGU8UfspBRfGhZrw3DSTnS3wYZjdR0QF
2/jwoBwt59i2hpFsMHmMYGU+307oVQ6Y9b/PXpnj4KqIG2CROB8eirDFkToxe4hC
Udy06IA70HUTBKzFmK1gCKZCZW3t2sB+zHtoVHJ8EARlFHWdLxLp83hA9p2Llfon
41iKnkf9CTiO2koEEzuOUOQW+KctIawryiUi4m+C5ZhJBKNk4GvIpXAg1JC9QX9E
GyqEICkg1dvc3GG5HYjPU7xq8mEdcHVOrHoiUci4zo9hMh6nHt7dboNeXQ13LNU9
joEqLvKEhUsm0J7cKWYOpxlHmNWGWNgqRas4Mot9zLUP7yYrxqLT5b2hD3PcjPl4
Jl+rbm4/2YMztWAnCU85EEPwVgJx9k7uyAEtXtQaWUValsVsWUWI1/F//IjYeLZI
AUx1euoarbCp6mXIoHLsOHV02uc=
=n8VS
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB changes for v4.21
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
usb: dwc2: Fix disable all EP's on disconnect
usb: dwc3: gadget: Disable CSP for stream OUT ep
usb: dwc2: disable power_down on Amlogic devices
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
usb: dwc3: trace: add missing break statement to make compiler happy
usb: dwc3: gadget: Report isoc transfer frame number
usb: gadget: Introduce frame_number to usb_request
usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
usb: renesas_usbhs: Remove dummy runtime PM callbacks
usb: dwc2: host: use hrtimer for NAK retries
usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
usb: mtu3: enable SETUPENDISR interrupt
usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
usb: mtu3: enable hardware remote wakeup from L1 automatically
usb: mtu3: remove QMU checksum
usb/mtu3: power down device ip at setup
usb: dwc2: Disable power down feature on Samsung SoCs
usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
...
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement the new frame_number API to report the isochronous interval
frame number. This patch checks and reports the interval in which the
isoc transfer was transmitted or received via the Isoc-First TRB SOF
number field.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Availability of TRB's is calculated using dwc3_calc_trbs_left(), which
determines total available TRB's based on the HWO bit set in a TRB.
In the present code, __dwc3_prepare_one_trb() is called with a TRB which
needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls
dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit
if the total available TRBs are zero. Since the present working TRB (which
is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have
the HWO bit set before calling dwc3_calc_trbs_left(), there are chances
that dwc3_calc_trbs_left() wrongly calculates this present working TRB
as free(since the HWO bit is not yet set) and returns the total available
TRBs as greater than zero (including the present working TRB). This could
be a problem.
This patch corrects the above mentioned problem in __dwc3_prepare_one_trb()
by increementing the dep->trb_enqueue at the last (after preparing the TRB)
instead of increementing at the start and setting the IOC bit only if the
total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are
increementing the dep->trb_enqueue at the last, the present working TRB is
also considered as available by dwc3_calc_trbs_left() and non zero value is
returned . So, according to the modified logic, when the total available
TRBs is equal to 1 that means the total available TRBs in the pool are 0.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stream capable endpoints require stream id to be given
when issuing START TRANSFER. While issuing no-op trb the
stream id is not yet known, so don't issue no-op trb's on
stream capable endpoints.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For stream capable endpoints, stream id related information
needs to be updated into DEPCMD while issuing START TRANSFER.
This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget driver may take an unbounded amount of time to queue requests
after XferNotReady. This is important for isochronous endpoints which
need to be started for a specific (micro-)frame.
If we fail to start a transfer for isochronous endpoint, let's try
queueing to a future interval and see if that helps. We will stop trying
if we fail a start transfer for 5 intervals in the future.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Running out of requests on isochronous endpoints is part of normal
operation. We don't really need to know about it every time it
happens.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sometimes, errors happen when kicking transfers from
__dwc3_gadget_start_isoc(). In those cases, we need to pass along the
error so gadget driver can make informed decisions.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have a list of cancelled requests, we can skip over TRBs
when END_TRANSFER command completes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Whenever we have a request in flight, we can move it to the cancelled
list and later simply iterate over that list and skip over any TRBs we
find.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Extract the logic for skipping over TRBs to its own function. This
makes the code slightly more readable and makes it easier to move this
call to its final resting place as a following patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we track how many TRBs a request uses, it's easier to skip
over them in case of a call to usb_ep_dequeue(). Let's do so and
simplify the code a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both flags are used for the same purpose in dwc3: appending an extra
TRB at the end to deal with controller requirements. By combining both
flags into one, we make it clear that the situation is the same and
that they should be treated equally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.
In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.
Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.
Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:
if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit ffb80fc672.
Turns out that commit is wrong. Host controllers are allowed to use
Clear Feature HALT as means to sync data toggle between host and
periperal.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current check for the last extra TRB for zero and unaligned transfers
does not account for isoc OUT. The last TRB of the Buffer Descriptor for
isoc OUT transfers will be retired with HWO=0. As a result, we won't
return early. The req->remaining will be updated to include the BUFSIZ
count of the extra TRB, and the actual number of transferred bytes
calculation will be wrong.
To fix this, check whether it's a short or zero packet and the last TRB
chain bit to return early.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
endpoint->maxpacket is not updated after setting the
usb_set_maxpacket_limit() on endpoint enable. The MaxPacketSize can be
different than the endpoint->maxpacket_limit.
DWC3 has been consistently using MaxPacketSize from the endpoint's
descriptor, so let's keep it consistent and use the MaxPacketSize from
the endpoint's descriptor instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following sparse warning:
drivers/usb/dwc3/gadget.c:169:6: warning:
symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We dont' need to touch req->direction or req->epnum from
ep_queue(). It's enough that we initialize both fields from
alloc_request() and just keep them for the entire lifetime of the
request.
No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of *always* calling dwc3_gadget_ep_get_transfer_index() after
sending a Start Transfer command, we can call it once from
dwc3_send_gadget_ep_cmd() itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning resource index number just to assign it to a
field inside 'dep' which was passed as argument, we can assing
dep->resource_index from inside dwc3_gadget_ep_get_transfer_index()
itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we have many started requests and one of them in the middle is
completed with Missed Isoc, let's not End Transfer as that would
result in us loosing (possibly) many more intervals.
Instead, let's allow the controller to go through its list of started
requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoid a prototype when the function can be defined earlier. No
functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of having a prototype for a function that's defined a few
lines down, let's just move definition to the place where prototype
was.
No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In a few places, the argument is completely unnecessary. On places
where it's needed, we can get it from dep->dwc.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Those two arguments refer to a single bitfield in the register. In
order to simplify the code, we can combine them into a single argument
and expect caller to pass the correct action argument at all times.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will only have event status of IOC when IOC bit is set in
TRB. There's no need to check both bits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that only OUT endpoints can trigger SHORT. We also know that
count MUST be > 0 whenever SHORT triggers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We are trying to kick transfers on Isochronous endpoints in a more
controlled manner now. And this ended up rendering this piece of code
unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having one big loop, let's split it down into two smaller
handlers: one for linear buffers and one for scatterlist.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After all the previous changes, it's now a lot clearer how isoc
transfers should be managed. We don't need to try to End Transfers
from ep_queue since that's already done by cleanup_requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now, this part of the code is duplicated and brings no extra value to
the driver. Let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we get an event with status set to Missed Isoc, this means we
have missed an isochronous interval and should issue End Transfer
command and wait for the following XferNotReady.
Let's do that early, rather than late.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By now, it has the same semantics as DWC3_EP_TRANSFER_STARTED, but
that has a much more descriptive name.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will need an up-to-date frame_number from XferInProgress too when
future patches improve our handling of Isoc endpoints.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The core requires the extra two bits of information for properly
scheduling Isochronous transfers. This means that we can't rely on
__dwc3_gadget_get_frame(). Let's always cache uFrame number from
XferNotReady instead.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Endpoint handlers need to know about endpoints, not dwc. If they
really need access to dwc (e.g. for printing error messages) we have a
reference to it tucked inside the endpoint.
This patch has no functional changes, it's simply moving things around.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We *KNOW* which events we enable for which endpoint types and
we *KNOW* when they'll trigger. The endpoint type checks are
pointless.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch simply renames two functions to more descriptive names so
that it's easier to understand what they're doing.
Cleanup only, no functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of constantly calling kick transfer everything some event
shows up, let's just rely on the fact that we send Update Transfer
every time a new request is queued.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we're making sure we don't have XferComplete events, we can
rename this function to what it actually handles:
dwc3_gadget_endpoint_transfer_in_progress()
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferComplete is enabled only for the default control pipe, let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't use XferNotReady for anything other than Default Control
Pipe, which is handled in ep0.c, and Isochronous endpoints. Let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Interrupt endpoints behave much like Bulk endpoints with the exception
that they are periodic. We can pre-issue Start Transfer exactly as we
do for Bulk endpoints.
While at that, remove one trailing blank line which is unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The present code correctly fetches the req which were previously not
queued from the started_list but fails to continue queuing from the sg
where it previously stopped queuing (because of the unavailable TRB's).
This patch correct's the code to continue queuing from the correct sg
present in the sglist.
For example, consider 5 sgs in req. Because of limited TRB's among the
5 sgs only 3 got queued. This patch corrects the code to start queuing
from correct sg i.e 4th sg when the TRBs are available.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The code logic in dwc3_prepare_one_trb() incorrectly uses the address
and length fields present in req packet for mapping TRB's instead of
using the address and length fields of scattergather lists. This patch
correct's the code to use sg->address and sg->length when scattergather
lists are present.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:
spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
free_ep_req(hidg->in_ep, hidg->req);
goto try_again;
}
[...]
status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
[...]
=> usb_gadget_giveback_request
=>
f_hidg_req_complete
=>
spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire
Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.
It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
Reported-by: Tuba Yavuz <tuba@ece.ufl.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC_usb3 speed can only be set up to SuperSpeed. Limit the setting to
SuperSpeed only should the value be higher. Otherwise, the controller
will read an invalid speed value and set the device to an incorrect
speed.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 controller has a different UsbRxPktCnt bit fields from
GRXTHRCFG register. Check for DWC_usb31 IP revision to read the
appropriate value.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 controller has different GTXFIFOSIZE bit field for TXFDEF.
Check for DWC_usb31 IP revision to read the appropriate bit fields.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the following test we get stuck by sleeping forever in _dwc3_set_mode()
after which dual-role switching doesn't work.
On dra7-evm's dual-role port,
- Load g_zero gadget driver and enumerate to host
- suspend to mem
- disconnect USB cable to host and connect otg cable with Pen drive in it.
- resume system
- we sleep indefinitely in _dwc3_set_mode due to.
dwc3_gadget_exit()->usb_del_gadget_udc()->udc_stop()->
dwc3_gadget_stop()->wait_event_lock_irq()
To fix this instead of waiting indefinitely with wait_event_lock_irq()
we use wait_event_interruptible_lock_irq_timeout() and print
and error message if there was a timeout.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.
The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.
Cc: stable@vger.kernel.org
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlpTWGYdHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQYDsw/4jOBzuVM2A28oCDzd
H9RCagGp4dXpdvLRpueE+L16AA/5MrAI1H1Tdp063Xr+CmlPeMf98JRI5tfBpfn5
8bE6yTojMfvb7vL82kjrnKwKh59IvKVLlFftPBIGJp1uKl5KwWUWMWRcvnpVJHdY
SlZ0U79Pje7RBuq0BkBQ9Lm47pPm5sMqzCyyte4wZbR+6GkAA5W0PBuRes0JLBHo
gUb9h5ns5afrxEdvzUXKpVpd++oP/ZLoZ++jYJ10Z5qSC8+y0DiwRxq7OdOSil+c
BEMKe7I46tGzDFZ2wuMQByHWqCXp7o+9VSf5BYxyP1L58qH1N7M7GyH0Oe+r5xAi
tjFrnL0C8Ax+ouaXLBfmFzv/52BjEqGoqtscWZ4XyVqq98NC1bP5b+qVmIkzXkdv
P7T2lOFZX0ILDX7QXIQbXv71UA/m3bwi3IG0eNX5Rik5xQjDVHnLDpuj87wW1wSH
aUg7sHpggn6GdOICHw9Zry3Z07u3Rab8ThuH0Z4oBI2+3EGhbXTHDjpKYwFYCWEw
nI+9XloOdEkOE6P3S2VO1cQ7YkJ+r4/YRDRvPq3XfLETfxPHwIjqiVeSQWaBA2U8
Om4f/1Oe83jtpfl1T7zL2z08TVPDNMOpE2j4FThA682Pa15emqymRXGDgDmFVizO
boMiMHcP8Wp0MMegK/3RL4syrg==
=uwh/
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.16 merge window
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.
This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.
If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.
[1] Device mode enumeration trace showing PHY Erratic Error.
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For isochronous endpoints with ep->mult less than 3, PCM1 value of
trb->size in set incorrectly.
For ep->mult = 2, this is set to 0/-1 and for ep->mult = 1, this is
set to -2. This is because the initial mult is set to ep->mult - 1
instead of 2.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all the information we need sits in struct dwc3_ep, we can
start taking only a pointer to struct dwc3_ep as an argument. This
allows us to clean the code up a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is more possibility for sharing code if we just realise that now
__dwc3_gadget_kic_transfer() knows to break out early if there are no
TRBs left.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will let us call __dwc3_gadget_kick_transfer()
unconditionally. No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The PIDs for Isochronous data transfers are incorrect
for high bandwidth IN endpoints when the request length
is less than EP wMaxPacketSize.
As per spec correct PIDs for ISOC data transfers are:
1) For request length <= maxpacket
- DATA0,
2) For maxpacket < length <= (2 * maxpacket)
- DATA1, DATA0
3) For (2 * maxpacket) < length <= (3 * maxpacket)
- DATA2, DATA1, DATA0.
But driver always sets PCM fields based on wMaxPacketSize
due to which DATA2 happens even for small requests.
Fix this by setting the PCM field of trb->size depending
on request length rather than fixing it to the value
depending on wMaxPacketSize.
Ideally it shouldn't give any issues as dwc3 will send
0-length packet for next IN token if host sends (even
after receiving a short packet). Windows seems to ignore
this but with MacOS frame loss observed when using f_uvc.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A recent optimization was made so that a request put on the
pending_list wouldn't get mapped for DMA until just before
preparing a TRB for it. However, this poses a problem in case
the request is dequeued or the endpoint is disabled before the
mapping is done as that would lead to dwc3_gadget_giveback()
unconditionally calling usb_gadget_unmap_request_for_dev() with
an invalid request->dma handle. Depending on the platform's DMA
implementation the unmap operation could result in a panic.
Since we know a successful mapping is a prerequisite for getting
a TRB, the unmap can be conditionally called only when req->trb
is non-NULL.
Fixes: cdb55b39fa ("usb: dwc3: gadget: lazily map requests for DMA")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
-----BEGIN PGP SIGNATURE-----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=v6a5
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
The commit 47d3946ea2
usb: dwc3: refactor gadget endpoint count calculation
refactored dwc3_gadget_init_endpoints() and in particular changed in or
out endpoint numbering to be through. It's not always convenient and
makes code a slightly harder to read.
Introduce a new temporary variable to make it easier to understand what
is going on inside the function.
While doing that, rename local variables as follows:
u8 num -> u8 total
int num -> int kbytes
Replace implicit direction check via epnum with explicit use of
direction variable.
While here, replace %d to %u when compounding endpoint name since we are
using unsigned type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use this method to make sure we don't try to connect on speeds not
supported by the gadget driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
%p will leak kernel pointers, so let's not expose the information on
dmesg and instead use %pK. %pK will only show the actual addresses if
explicitly enabled under /proc/sys/kernel/kptr_restrict.
Cc: <stable@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some functions might want to have very, very long request queues. We
can't make any assumptions about how many requests we *are* able to
map, so instead of mapping requests early, let's map them late. This
way, functions can queue as many requests as they'd like but we won't
take DMA resources until they are needed.
Also, we can now stop processing requests when we run out of DMA
resources but still keep requests in the queue for late processing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need a big fat warning with stack dump at all. Running out of
TRBs is a normal condition and we will have more TRBs available as
soon as some transfers complete.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc3 driver can overwite its previous events if its top-half IRQ
handler (TH) gets invoked again before processing the events in the
cache. We see this as a hang in the file transfer and the host will
attempt to reset the device. TH gets the event count and deasserts the
interrupt line by writing DWC3_GEVNTSIZ_INTMASK to DWC3_GEVNTSIZ. If
there's a new event coming between reading the event count and interrupt
deassertion, dwc3 will lose previous pending events. More generally, we
will see 0 event count, which should not affect anything.
This shouldn't be possible in the current dwc3 implementation. However,
through testing and reading the PCIe trace, the TH occasionally still
gets invoked one more time after HW interrupt deassertion. (With PCIe
legacy interrupts, TH is called repeatedly as long as the interrupt line
is asserted). We suspect that there is a small detection delay in the
SW.
To avoid this issue, Check DWC3_EVENT_PENDING flag to determine if the
events are processed in the bottom-half IRQ handler. If not, return
IRQ_HANDLED and don't process new event.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
caused a small change in the way ISO transfer is handled in the case
when XferInProgress event happens on Isoc EP with an active transfer.
This caused a performance degradation of 50%. e.g. using g_webcam on DUT
and luvcview on host the video frame rate dropped from 16fps to 8fps
@high-speed.
Make the ISO transfer handling equivalent to that prior to that commit
to get back the original ISO performance numbers.
Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's much simpler to just add one extra TRB chained to previous TRB to
handle ZLP. This helps us reduce pointless allocations and simplifies
the code a little bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for all other endpoint types, let's rely on a chained
TRB pointing to ep0_bounce_addr in order to align transfer size. This
will make the code simpler.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we pass TRB's own address on bpl/bph fields, we can get our SETUP
packet as immediate data on the TRB itself, without having to allocate
extra memory for it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget wants to set the starting microframe for the first ISOC TRB
to 4 microframes in the future, but it does so by multiplying the
dep->interval. This only works if dep->interval = 1. For other intervals
it will put it 4 *intervals* in the future which may be way too much.
Fix so that it always adds just one interval or at least 4 microframes.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A previous patch in the series reduces the number of callsites of
dwc3_gadget_init_hw_endpoints from two to one. This patch removes the
redundant step of wrappering one function in the other, which can be done
by adding a parameter to dwc3_gadget_init_endpoints and moving the
linked-list initialization of dwc->gadet.ep_list.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- DWC_USB3_NUM indicates the number of Device mode single directional
endpoints, including OUT and IN endpoint 0.
- DWC_USB3_NUM_IN_EPS indicates the maximum number of Device mode IN
endpoints active at any time, including control endpoint 0.
It's possible to configure RTL such that DWC_USB3_NUM_EPS is equal to
DWC_USB3_NUM_IN_EPS.
dwc3-core calculates the number of OUT endpoints as DWC_USB3_NUM minus
DWC_USB3_NUM_IN_EPS. If RTL has been configured with DWC_USB3_NUM_IN_EPS
equal to DWC_USB3_NUM then dwc3-core will calculate the number of OUT
endpoints as zero.
For example a from dwc3_core_num_eps() shows:
[ 1.565000] /usb0@f01d0000: found 8 IN and 0 OUT endpoints
This patch refactors the endpoint calculation down to one variable
dwc->num_eps taking care to maintain the current mapping of endpoints for
fixed FPGA configurations as described in Table 4-7 of version 2.60a of the
DWC USB3 databook.
The endpoint mapping will then be EP-OUT, EP-IN etc, up to DWC_USB3_NUM.
If DWC_USB3_NUM is odd then OUT will take the extra endpoint.
Suggested-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case of bounced ep0 requests, we must delay DMA operation until
after ->complete() otherwise we might overwrite contents of req->buf.
This caused problems with RNDIS gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sometimes, we might get a completion for a TRB which is left with HWO
bit. Even in these cases, we should increment req->remaining to
properly report total transferred size. I noticed this while debuggin
a separate problem seen with MSC tests from USBCV. Sometimes we would
erroneously report a completion for a 512-byte transfer when, in
reality, we transferred 0 bytes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On TI platforms (dra7, am437x), the DWC3_DSTS_DEVCTRLHLT bit is not set
after the device controller is stopped via DWC3_DCTL_RUN_STOP.
If we don't disconnect and stop the gadget, it stops working after a
system resume with the trace below.
There is no point in preventing gadget disconnect and gadget stop during
system suspend/resume as we're going to suspend in any case, whether
DEVCTRLHLT timed out or not.
[ 141.727480] ------------[ cut here ]------------
[ 141.732349] WARNING: CPU: 1 PID: 2135 at drivers/usb/dwc3/gadget.c:2384 dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3]
[ 141.744299] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 evdev udc_core m25p80 usb_common spi_nor snd_soc_davinci_mcasp snd_soc_simple_card snd_soc_edma snd_soc_tlv3e
[ 141.792163] CPU: 1 PID: 2135 Comm: irq/456-dwc3 Not tainted 4.10.0-rc8 #1138
[ 141.799547] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 141.805940] [<c01101b4>] (unwind_backtrace) from [<c010c31c>] (show_stack+0x10/0x14)
[ 141.814066] [<c010c31c>] (show_stack) from [<c04a0918>] (dump_stack+0xac/0xe0)
[ 141.821648] [<c04a0918>] (dump_stack) from [<c013708c>] (__warn+0xd8/0x104)
[ 141.828955] [<c013708c>] (__warn) from [<c0137164>] (warn_slowpath_null+0x20/0x28)
[ 141.836902] [<c0137164>] (warn_slowpath_null) from [<bf27784c>] (dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3])
[ 141.848329] [<bf27784c>] (dwc3_stop_active_transfer.constprop.4 [dwc3]) from [<bf27ab14>] (__dwc3_gadget_ep_disable+0x64/0x528 [dwc3])
[ 141.861034] [<bf27ab14>] (__dwc3_gadget_ep_disable [dwc3]) from [<bf27c27c>] (dwc3_gadget_ep_disable+0x3c/0xc8 [dwc3])
[ 141.872280] [<bf27c27c>] (dwc3_gadget_ep_disable [dwc3]) from [<bf23b428>] (usb_ep_disable+0x11c/0x18c [udc_core])
[ 141.883160] [<bf23b428>] (usb_ep_disable [udc_core]) from [<bf342774>] (disable_ep+0x18/0x54 [usb_f_ss_lb])
[ 141.893408] [<bf342774>] (disable_ep [usb_f_ss_lb]) from [<bf3437b0>] (disable_endpoints+0x18/0x50 [usb_f_ss_lb])
[ 141.904168] [<bf3437b0>] (disable_endpoints [usb_f_ss_lb]) from [<bf343814>] (disable_source_sink+0x2c/0x34 [usb_f_ss_lb])
[ 141.915771] [<bf343814>] (disable_source_sink [usb_f_ss_lb]) from [<bf329a9c>] (reset_config+0x48/0x7c [libcomposite])
[ 141.927012] [<bf329a9c>] (reset_config [libcomposite]) from [<bf329afc>] (composite_disconnect+0x2c/0x54 [libcomposite])
[ 141.938444] [<bf329afc>] (composite_disconnect [libcomposite]) from [<bf23d7dc>] (usb_gadget_udc_reset+0x10/0x34 [udc_core])
[ 141.950237] [<bf23d7dc>] (usb_gadget_udc_reset [udc_core]) from [<bf276d70>] (dwc3_gadget_reset_interrupt+0x64/0x698 [dwc3])
[ 141.962022] [<bf276d70>] (dwc3_gadget_reset_interrupt [dwc3]) from [<bf27952c>] (dwc3_thread_interrupt+0x618/0x1a3c [dwc3])
[ 141.973723] [<bf27952c>] (dwc3_thread_interrupt [dwc3]) from [<c01a7ce8>] (irq_thread_fn+0x1c/0x54)
[ 141.983215] [<c01a7ce8>] (irq_thread_fn) from [<c01a7fbc>] (irq_thread+0x120/0x1f0)
[ 141.991247] [<c01a7fbc>] (irq_thread) from [<c015ba14>] (kthread+0xf8/0x138)
[ 141.998641] [<c015ba14>] (kthread) from [<c01078f0>] (ret_from_fork+0x14/0x24)
[ 142.006213] ---[ end trace b4ecfe9f175b9a9c ]---
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If request was already started, this means we had to
stop the transfer. With that we also need to ignore
all TRBs used by the request, however TRBs can only
be modified after completion of END_TRANSFER
command. So what we have to do here is wait for
END_TRANSFER completion and only after that jump
over TRBs by clearing HWO and incrementing dequeue
pointer.
Note that we have 2 possible types of transfers
here:
i) Linear buffer request
ii) SG-list based request
SG-list based requests will have r->num_pending_sgs
set to a valid number (> 0). Linear requests,
normally use a single TRB.
For each of these two cases, if r->unaligned flag is
set, one extra TRB has been used to align transfer
size to wMaxPacketSize.
All of these cases need to be taken into
consideration so we don't mess up our TRB ring
pointers.
Tested-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of assuming all IN endpoints support 1024
bytes, let's read the actual value from HW and pass
that to gadget API.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
At least macOS seems to be sending
ClearFeature(ENDPOINT_HALT) to endpoints which
aren't Halted. This makes DWC3's CLEARSTALL command
time out which causes several issues for the driver.
Instead, let's just return 0 and bail out early.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of passing quirk_ep_out_aligned_size, we can use one extra TRB
to align transfer to wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allocate a coherent buffer of 1024 bytes (size of a single superspeed
bulk packet) to serve as bounce buffer for an extra TRB needed to align
transfers to wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This new internal function will be used to solve a minor issue with dwc3
which exists in regards to short packets with OUT endpoints. Currently
we're asking gadget driver to *always* send us aligned requests; however
if we have enough TRBs we can easily append one extra TRB chained to the
previous and keep a throw away 1024 byte buffer around for that.
The actual fix will come in a separate patch, this is merely in
preparation for such fix.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We are already passing struct dwc3_request * to dwc3_prepare_one_trb(),
because of that there's no need to extract dma address and length in the
caller. We can let dwc3_prepare_one_trb() itself handle that part.
This simplifies the prototype of the function by removing two arguments.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DCFG.DEVSPD == 0x3 is not valid and we need to set
DCFG.DEVSPD to 0x1 for full speed mode. Same goes for
DSTS.CONNECTSPD.
Old databooks had 0x3 for full speed in 48MHz mode for
USB1.1 transceivers which was never supported. Newer databooks
don't mention 0x3 at all.
Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case EP disabled pass only EPCPLT command
to be handled. In other case we could hit
Bug like below.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP:
[<ffffffff81673428>] dwc3_thread_interrupt+0x11c8/0x1790
while dep->endpoint.desc is NULL.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.
Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.
Fixes: 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced")
Cc: <stable@vger.kernel.org>
Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement interrupt moderation which allows the interrupt rate to be
throttled. To enable this feature the dwc->imod_interval must be set to
1 or greater. This value specifies the minimum inter-interrupt interval,
in 250 ns increments. A value of 0 disables interrupt moderation.
This applies for DWC_usb3 version 3.00a and higher and for DWC_usb31
version 1.20a and higher.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that all the infrastructure is in place, we can
clear events in the top-half handler in order to
bring IRQ line low ASAP.
This is also a necessary step in order to implement
workaround for known erratum in follow-up patches.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's start copying events from evt->buf to
evt->cache and use evt->cache for processing events.
A follow-up patch will be added to clear events in
the top-half handler in order to bring IRQ line low
as soon as possible.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of always accessing the macro directly,
let's rely on evt->length which is the actual length
of current event buffer. While unlikely, we could
change event buffer's size at any time.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The register programming code in dwc2_updated_ram_clk_sel() will never
be executed. And in fact the entire function can be removed as there is
no way to override the default value of GCTL.RAMCLKSEL. Remove the
function and add a comment explaining where GCTL.RAMCLKSEL should be
programmed if needed in the future.
This fixes dead code warnings in coverity.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The __dwc3_gadget_endpoint_enable() function has access to the endpoint
descriptors via the usb_ep. So we don't need to pass them in as
arguments. The descriptors should be set by the caller prior to calling
usb_ep_enable().
Signed-off-by: John Youn <johnyoun@synopsys.com>
[felipe.balbi@linux.intel.com : minor improvements]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Seems last time we hit few issues where
we get trb_left = 0, mainly because of
HWO bit still set in previous TRB.
Add warn on once to catch/fix such
problems much faster.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After we kick_transfer we should clean
DWC3_EP_PENDING_REQUEST endpoint flag.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use pre-increment and set -ETIMEDOUT correctly.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case STARTTRANSFER will fail, clean TRB.
Seems HW in such case don't clean HWO bit.
So, without this cleanup prev_trb still have
HWO bit set.
In my case (without patch), after first START failed:
- dep->enqueue == 1
- dep->dequeue == 1
- prev_trb still have HWO set
- left_trb() == 0
No way to send more data.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we will fail to STARTTRANSFER we should
also decrement queued_requests.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a simple trace_printk() wrapper,
let's add an actual tracepoint and print further
details about the endpoint being operated upon.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we get a half-way processed request, we should
make sure to try to prepare further TRBs for it or
for any possibly queued up request held in our
pending_list. This will make sure our controller is
kept busy for as long as possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Say we have three requests prepared to the HW (reqA,
reqB, and reqC). All of them are composed of
SG-lists with several entries and they all requests
interrupt only on last TRBs of the SG-list.
When we get interrupt for reqA, it could be that
reqB is already half-way transferred and some of its
TRBs will have HWO already cleared.
It's okay to free up TRBs without HWO bit set, but
we need to guarantee we don't giveback a request
that's half-way transferred as that will confuse
gadget drivers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In cases where we're given an SG-list which is
longer than the amount of currently available TRBs,
we will be left with the same request on
started_list and we should prioritize that request
over possible new requests on pending_list. That's
a way to guarantee requests complete in order.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will give us a simpler way of figuring out how
many bytes were left in each TRB. It's useful for
cases where we queue only part of an SG-list due to
amount of available TRBs at the time of kicking the
transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If XferNotReady comes before usb_ep_queue() we will
set our PENDING request flag and wait for a
request. However, originally, we were assuming
usb_ep_queue() would always happen before our first
XferNotReady and that causes a corner case where we
could try to issue ENDTRANSFER command before
STARTTRANSFER.
Let's fix that by tracking endpoints which have been
started.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of just delaying for 100us, we should
actually wait for End Transfer Command Complete
interrupt before moving on. Note that this should
only be done if we're dealing with one of the core
revisions that actually require the interrupt before
moving on.
[ felipe.balbi@linux.intel.com: minor improvements ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we change the USB function with configfs dynamically, we possibly
met this situation: one core is doing the control transfer, another core
is trying to unregister the USB gadget from userspace, we must wait for
completing this control tranfer, or it will hang the controller to set
the DEVCTRLHLT flag.
[ felipe.balbi@linux.intel.com: several fixes to the patch
- call complete() before starting following SETUP transfer
- add a macro for ep0_in_setup's timeout
- change commit subject slightly
- break lines at 72 characters (git adds an 8-character tab)
- avoid changes to dwc3_gadget_run_stop() ]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That function is unnecessarily called from
dwc3_gadget_reset_interrupt(). Gadget drivers (and
thus, functions) are required to dequeue all pending
requests when they get notified about a USB Bus
Reset.
Trying to make sure there are no pending requests
only serves the purpose of working around possibly
bad gadgets.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should never kill the machine just because some
USB endpoint type is wrong. WARN about it and move
on.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't need to know about short packets unless
gadget driver told us it's not ok to see them on the
bus. In the normal situation we can continue
processing the list of requests if we get a Short
packet.
Also, note that we're making sure ISP is only set
for OUT endpoints, where that setting is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit is only valid for OUT endpoints. Synopsys
databook is unclear if HW ignores CSP for IN
endpoints (chances are, it does) but to avoid
problems, let's make sure to set CSP only when valid
to do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can offset the latency of a full Start Transfer
command - where we _must_ poll for its completion -
to usb_ep_enable() time. This means that once
requests start showing up from the gadget driver, we
can rely on No Response Update Transfer command -
where we don't need to poll for completion.
This patch, starts implementing this method for Bulk
endpoints, even though, technically, we could extend
it to all other endpoints in future commits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With this extra piece of information, it will be
easier to find mismatches between driver and HW.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removing some trace prints which were made redundant
when we started decoding events and TRBs completely
within their respective trace points.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link State Change events are only needed for
debugging and to apply certain workarounds on known
errata. Let's save a few cycles by disabling these
events completely on working revisions of the core.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There might be situations where a Start Transfer
command might fail, if that ever happens, instead of
simply removing the request from our list, we should
give the request back to the gadget driver,
otherwise we might eventually starve it from requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No Response Update Transfer is a special type of
Update Transfer command which can be used whenever
we're not relying on XferNotReady to prepare
transfers. With this, we don't need to wait for
CMDACT to be cleared and issue further commands to
the endpoint straight away.
Let's start using this version to skip the long-ish
wait.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The cmd argument we pass to
dwc3_send_gadget_ep_cmd() could contain extra
arguments embedded. When checking for StartTransfer
command, we need to make sure to match only lower 4
bits which contain the actual command and ignore the
rest.
Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of High-Speed, High-Bandwidth endpoints, we
need to tell DWC3 that we have more than one packet
per interval. We do that by setting PCM1 field of
Isochronous-First TRB.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In commit 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support"), the
size of the memory allocated with 'dma_alloc_coherent()' has been modified
but the corresponding calls to 'dma_free_coherent()' have not been updated
accordingly.
This has been spotted with coccinelle, using the following script:
////////////////////
@r@
expression x0, x1, y0, y1, z0, z1, t0, t1, ret;
@@
* ret = dma_alloc_coherent(x0, y0, z0, t0);
...
* dma_free_coherent(x1, y1, ret, t1);
@script:python@
y0 << r.y0;
y1 << r.y1;
@@
if y1.find(y0) == -1:
print "WARNING: sizes look different: '%s' vs '%s'" % (y0, y1)
////////////////////
Fixes: 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We cannot pre-start isochronous endpoints because we
rely on the micro-frame number passed via
XferNotReady command for proper Isochronous
scheduling.
Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some requests could be accounted for multiple
times. Let's fix that so each and every requests is
accounted for only once.
Cc: <stable@vger.kernel.org> # v4.8
Fixes: 55a0237f8f ("usb: dwc3: gadget: use allocated/queued reqs for LST bit")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
-----BEGIN PGP SIGNATURE-----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=vTFa
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
Commit 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear
Stall EP command") sets ClearPendIN bit for all IN endpoints of
v2.60a+ cores. This causes ClearStall command fails on 2.60+ cores
operating in HighSpeed mode.
In page 539 of 2.60a specification:
"When issuing Clear Stall command for IN endpoints in SuperSpeed
mode, the software must set the "ClearPendIN" bit to '1' to
clear any pending IN transcations, so that the device does not
expect any ACK TP from the host for the data sent earlier."
It's obvious that we only need to apply this rule to those IN
endpoints that currently operating in SuperSpeed mode.
Fixes: 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleaning up the loop in dwc3_cleanup_done_reqs() introduced a
gcc warning if built with "-Wmaybe-uninitialized":
drivers/usb/dwc3/gadget.c: In function 'dwc3_endpoint_transfer_complete':
drivers/usb/dwc3/gadget.c:2015:9: 'trb' may be used uninitialized in this function [-Wmaybe-uninitialized]
I believe it is a false positive and we always have a valid 'trb'
pointer at the end of the function, but neither I nor the compiler
are able to prove that.
This works around the warning by computing a flag earlier in the function
when it's guaranteed to be valid, which tells the compiler that it's
safe and makes it easier to understand to me.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 31162af447 ("usb: dwc3: gadget: avoid while (1) loop on completion")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 6f8245b4e3 ("usb: dwc3: gadget: always decrement
by 1").
We can't always decrement this value.
We should decrement only if the calculation of free slots results in a
LINK TRB being among one of the free slots (dequeue < enqueue).
Otherwise, if the LINK TRB is not among the free slots then it should
not be decremented.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].
This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().
This makes the code easier to follow while making
sure that we will *always* break out of the loop.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.
While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.
This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
__dwc3_gadget_wakeup() is called while holding a spinlock, then depends on
jiffies in order to timeout while polling the USB core for a link state
update. In the case the wakeup failed, the timeout will never happen and
will also cause the cpu to stall until rcu_preempt kicks in.
This switches to a "decrement variable and wait" timeout scheme.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:
The LST bit should be set to 0 (isochronous
transfers normally continue until the
endpoint is removed entirely, at which time
an End Transfer command is used to stop the
transfer).
This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Cc: <stable@vger.kernel.org>
Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It had changed to be suspend event for BIT6 in DEVT register from
version 2.30a and above. Thus this patch introduces one suspend
event handler to handle the suspend event.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.
Following are the interrupt names
Peripheral Interrupt - peripheral
HOST Interrupt - host
Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.
As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be crash to stop gadget when the dwc3 device had been into suspend
state, thus we need to check if the dwc3 device had been into suspend state
when UDC try to stop gadget.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Because of recent changes to transfer handling on
DWC3, we will not get XferComplete unless we
completely fill up our TRB ring. This means that we
might get a Reset or Disconnect without getting a
XferComplete first.
In order to correctly release our allocated Transfer
Resource, we must issue ENDTRANSFER command whenever
dep->resource_index is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
it's clear now that when is_on=true, we must loop
until DWC3_DSTS_DEVCTRLHLT clears; while when
is_on=false we must loop until DWC3_DSTS_DEVCTRLHLT
gets set.
Instead of adding actual if() statements, we can
rely on XOR operation to evaluate to true only when
the above conditions apply. Then, we can move the
break condition back to the while() statement
together with our timeout check and the resulting
code is very compact and simpler to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of looping forever and forcing a return if
timeout reaches zero, we can just use timeout and
loop's break condition directly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
testing shows that udelay() is unnecessary as
controller reaches Halted state almost
instantenously as can be seen by our timeout
variable never actually decrementing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'modify' is what the current action is called. Let's
rename it so it matches databook. While at that,
also make sure to add support 'init' action too.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now we can try to issue Update Transfer every time
gadget driver queues a new request. This will make
sure we keep controller's queue busy for as long as
possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's only set LST bit when we run out of space in
our TRB ring. For all other cases, we keep LST bit
unset which will prevent constant allocation and
deallocation of endpoint transfer resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of relying on empty list of queued requests,
let's rely on the fact that we have a TRB being
processed right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will be using this information to change how we
figure out when we need LST bit. For now, just
update our counters.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to SNPS databook, we need to pass transfer
resource on update transfer command, let's do it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when passing strings to trace, we don't need the
trailing newline character. Trace already appends a
newline character automatically.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Correct the use of the DWC3_DSTS_XXX_SPEED and DWC3_DCFG_XXX_SPEED
macros. The wrong set of macros were being used in a few places.
This is only a cosmetic change as the values for both sets are
identical.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
From sparse:
warning: cast truncates bits from constant value (100 becomes 0)
The DWC3_TRB_NUM constant is too big for u8. Do the calculation a
slightly different way that should still be optimized out for the case
where DWC3_TRB_NUM == 256.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the trb->enqueue == trb->dequeue, then it could be full or empty.
This could also happen at TRB index 0, so modify the check to handle
that condition. At index 0, the previous TRB is the one just before the
link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The TRBs left calculation didn't account for the link TRB taking up one
spot.
If the trb_dequeue < trb_enqueue, then the result includes the link
TRB slot so it must be adjusted.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current calculation takes dep->trb_dequeue - dep->trb_enqueue to
find the TRB space left.
If you enqueue 1, that results in:
(u8) 0 - (u8) 1 = 0xff = 255 TRBs left.
This is correct if DWC3_TRB_NUM == 256.
If DWC3_TRB_NUM is less than 256 (but still a power of 2) you need to
mod the result by DWC3_TRB_NUM.
For example the same calculation with DWC3_TRB_NUM = 8, results in:
255 % 6 = 7 TRBs left.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If trbs_left == 0, we don't have any space left in the TRB ring so don't
prepare anything.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Clears out all the TRBs in the ring to clean up any stale data that
might be in them from the previous time the endpoint was enabled.
Also removed the existing clear of the LINK trb since the entire ring is
cleard just before.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the skipping of the link TRBS built-in to the increment operation.
This simplifies the code wherever we increment the trb index and ensures
that we never end up pointing to a link trb.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cleans up the sparse warning:
warning: dubious: x | !y
Since we do want a bitwise OR here, don't use a logical (true/false)
value. Probably is not a real issue but it cleans up the warning.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's have a
single trace output for the command and its
status. This will improve trace readability
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for endpoint commands, let's use a
single return point for generic commands as
well. This aids readability.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing command's status with a separate
trace printout, let's print it within a single call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having infinite loop and always checking
timeout value as a break condition, we can just
decrement timeout inside while's condition.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I really thought this would be useful, but as it
turns out, it creates more problems than fixes. The
amount of times we had to fix this because some
other commit shuffled things around and ended up
regressing this tiny little string manupulation...
Might as well remove it, since it has a negligible
added benefit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will allow us to process several endpoints at a
time by making sure that we lock only shared
resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this patch implements the most basic pm_runtime
support for dwc3. Whenever USB cable is dettached,
then we will allow core to runtime_suspend.
Runtime suspending will involve completely tearing
down event buffers and require a full soft-reset of
the IP.
Note that a further optimization could be
implemented once we decide to support hibernation,
which is to allow runtime_suspend with cable
connected when bus is in U3. That's subject to a
separate patch, however.
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when we call dwc3_gadget_giveback(), we end up
releasing our controller's lock. Another thread
could get scheduled and disable the endpoint,
subsequently setting dep->endpoint.desc to NULL.
In that case, we would end up dereferencing a NULL
pointer which would result in a Kernel Oops. Let's
avoid the problem by simply returning early if we
have a NULL descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit f3af36511e ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.
Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.
Fixes: f3af36511e ("usb: dwc3: gadget: always enable IOC
on bulk/interrupt transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.
Fixes: 2b0f11df84 ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
by holding gadget's IRQ number in dwc->irq_gadget,
it'll be simpler to free_irq() and disable the IRQ
in case an IRQ fires while we are runtime suspended.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By adding a pointer to endpoint registers' base
address, we can avoid using our controller-wide
struct dwc3 pointer for everything. At some point
this will allow us to have per-endpoint locks which
will, in turn, let us queue requests to separate
endpoints in parallel.
Because of this change our debugfs interface and io
accessors need to be changed accordingly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In all call sites of dwc3_send_gadget_ep_cmd() we
already had a valid dep pointer, so instead of
passing dwc and dep->number, which would be used to
fetch the same pointer we already had, just pass dep
directly.
In other words, we're changing:
struct dwc3_ep *dep = dwc[dep->number];
to just passing struct dwc3_ep *dep as argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of using burst size to configure NUMP, we
should be using RxFIFO Size instead. DWC3 is smart
enough to know that it shouldn't burst in case burst
size is 0.
Reported-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To aid code readability, we're gonna split
__dwc3_gadget_kick_transfer() into its constituent
parts: scatter gather and linear buffers.
That way, it's easier to follow the code and focus
debug effort when one or the other fails.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning -EINVAL when someone calls
__dwc3_gadget_wakeup() in speeds > highspeed, let's
return 0. There are no problems for the driver for
calling it in superspeed as we cleanly just return.
This avoids an annoying WARN_ONCE() always
triggering during superspeed enumeration with LPM
enabled.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we send an endpoint command, we want that to
complete as soon as possible, so let's remove the
unnecessary udelay(1) call.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
sg_is_last() and list_is_last() will encode the
required information for the driver to make
decisions WRT CHN and LST bits.
While at that, also replace '1' with 'true' for
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
as it turns out, we don't need the extra 'start_new'
argument as that can be inferred from DWC3_EP_BUSY
flag.
Because of that, we can simplify
__dwc3_gadget_kick_transfer() by quite a bit, even
allowing us to prepare more TRBs unconditionally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we're updating transfers, we can also prepare as
many TRBs as we can fit in the ring. Let's start
doing that.
This patch 'solves' a limitation of how many TRBs we
can prepare when we're getting close the end of the
ring. Instead driver to prepare only up to end of
the ring, we check if we have space to wrap around
the ring properly.
Note that this only happens when our enqueue and
dequeue pointers are equal (which is the case for
bulk endpoints after an XferComplete event).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of trying hard to stay connected to the
host, it's best (and far easier) to disconnect from
the host already.
Anything relying on KEEP_CONNECT will just have that
ignored, but we don't have proper hibernation
implementation yet, so there are no regressions.
In any case, hibernation is only useful for runtime
PM, not system sleep.
While at that, also remove dwc3.dcfg which has been
rendered unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be re-using it for suspend/resume, so
instead of duplicating code, let's just re-factor
the functions so they can be re-used.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As of core revision 2.60a the recommended programming model is to set
the ClearPendIN bit when issuing a Clear Stall EP command for IN
endpoints. This is to prevent an issue where some (non-compliant) hosts
may not send ACK TPs for pending IN transfers due to a mishandled error
condition. Synopsys STAR 9000614252.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
Now that we calculate DCFG.NUMP, we can disable
dwc3's automatic calculation so we maximize our
chances of very high throughtput through the use of
bursts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NumP field of DCFG register is used on NumP field of
ACK TP header and it tells the host how many packets
an endpoint can receive before waiting for
synchronization.
Documentation says it should be set to anything
<=bMaxBurst. Interestingly, however, this setting is
not per-endpoint how it should be (different
endpoints could have different burst sizes), but
things seem to work okay right now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.
It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget controller might not be always active during system
suspend/resume as gadget driver might not have yet been loaded or
might have been unloaded prior to system suspend.
Check if we're active and only then perform
necessary actions during suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
request_list and req_queued were, well, weird naming
choices.
Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.
While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).
We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).
Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.
This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We were exitting the function before actually
renaming anything. While at that, also always leave
control endpoint un-renamed.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's a requirement that we release controller's lock
while calling gadget API function pointers. This
patch just fixes that long standing bug.
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check that dwc->maximum_speed is set to a valid value. Also add an error
when we use it later if we encounter an invalid value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable SuperSpeedPlus by programming the DCFG.speed and after
enumerating, set gadget->speed appropriately.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update various places where the speed is checked so that it takes into
account SuperSpeedPlus properly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch is needed in order to pass one test case
defined in the OTG Automated Compliance Test specification.
Specification location:
http://www.usb.org/developers/onthego/otgeh_compliance_plan_1_2.pdf
This test case uses PET Tool, and PET Tool is one USB hardware
equipment provided by MQP Electronics.
Test case id is 6.8.3 B-UUT Bypass Capacitance.
We must set this otg flag in order to be able to return OTG
descriptor during enumeration, otherwise this test case with
failed with below error: "Get OTG descriptor request stalled".
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the request->length is zero, a ZLP should already be sent due to that
and another ZLP is not needed to terminate the transfer.
Fixes: 04c03d10e5 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.
Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It just ocurred to me that dwc3 already gives a
really hint of when a setup packet is pending and
that's the SETUP_PENDING TRB Status for EP0 IRQs.
Fix setup_packet_pending initialization based on
that. While at that, also make sure the comment in
gadget.c matches what code is doing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In dwc3_cleanup_done_reqs() we expect that all
iterations of our while (1) loop will find a valid
struct dwc3_request *. In case we don't, we're
dumping a WARN_ON_ONCE() splat so that people report
the failure.
This patch is a simple cleanup converting:
if (!req) {
WARN_ON_ONCE(1);
return 1;
}
to:
if (WARN_ON_ONCE(!req))
return 1;
which is a little easier to read.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
By moving our sanity checks our internal function
__dwc3_gadget_ep_queue() we can simplify the
externally visible API while also making sure that
callers of __dwc3_gadget_ep_queue() also make use of
the same checks.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Because interrupt endpoints usually transmit such
small amounts of data, it seems pointless to prestart
transfers and try to get speed improvements. This
patch also sorts out a problem with CDC ECM function
where its notification endpoint gets stuck in busy
state and we continuously issue Update Transfer
commands.
Fixes: 8a1a9c9e45 ("usb: dwc3: gadget: start transfer on XFER_COMPLETE")
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 8f2c9544ab.
As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out
fine, but after a bit of data has been transferred it just stops
flowing.
Note that I do get a bunch of these "NOHZ: local_softirq_pending 08"
when booting the machine, but I'm not really sure if they're related
to this problem.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 70f3a9caa1.
That commit was causing a lockdep splat with g_ether and that
was interfering with proper functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We *know* our threads executes with our IRQs
disabled. We really don't need to use the _irqsave()
variant of spin_lock().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of limiting __dwc3_gadget_kick_transfer() to
Xfer Complete, we can try to issue Update Transfer
command from Xfer In Progress too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we get a Xfer Not Ready event with reason
"Transfer Active" it means endpoint is still
transferring data and we can use that to issue
update transfer for this particular endpoint
in case we have pending requests in our queue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if by the time we get to XFER_COMPLETE we have
pending requests to be processed, instead of waiting
for a following XFER_NOT_READY, let's start the request
right away and, maybe, save the time of a few NAKs
due to lack of started transfers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We shouldn't return -EBUSY, that's used only internally
when the core still has transfers in flight on a given
endpoint.
Also, combine the error reporting so that we don't have
to duplicate it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
