The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The frame checksum (FCS) is currently handled in gsm_queue() after
reception of a frame. However, this breaks layering. A workaround with
'received_fcs' was implemented so far.
Furthermore, frames are handled as such even if no end flag was received.
Move FCS calculation from gsm_queue() to gsm0_receive() and gsm1_receive().
Also delay gsm_queue() call there until a full frame was received to fix
both points.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.8.2 states that both sides will revert to
the non-multiplexed mode via a close-down message (CLD). The usual program
flow is as following:
- start multiplex mode by sending AT+CMUX to the mobile
- establish the control channel (DLCI 0)
- establish user channels (DLCI >0)
- terminate user channels
- send close-down message (CLD)
- revert to AT protocol (i.e. leave multiplexed mode)
The AT protocol is out of scope of the n_gsm driver. However,
gsm_disconnect() sends CLD if gsm_config() detects that the requested
parameters require the mux protocol to restart. The next immediate action
is to start the mux protocol by opening DLCI 0 again. Any responder side
which handles CLD commands correctly forces us to fail at this point
because AT+CMUX needs to be sent to the mobile to start the mux again.
Therefore, remove the CLD command in this phase and keep both sides in
multiplexed mode.
Remove the gsm_disconnect() function as it become unnecessary and merge the
remaining parts into gsm_cleanup_mux() to handle the termination order and
locking correctly.
Fixes: 71e0779153 ("tty: n_gsm: do not send/receive in ldisc close path")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, only the initiator resets the mux protocol if the user requests
new parameters that are incompatible to those of the current connection.
The responder also needs to reset the multiplexer if the new parameter set
requires this. Otherwise, we end up with an inconsistent parameter set
between initiator and responder.
Revert the old behavior to inform the peer upon an incompatible parameter
set change from the user on the responder side by re-establishing the mux
protocol in such case.
Fixes: 509067bbd2 ("tty: n_gsm: Delete gsm_disconnect when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation the user may open a virtual tty which then
could fail to establish the underlying DLCI. The function gsmtty_open()
gets stuck in tty_port_block_til_ready() while waiting for a carrier rise.
This happens if the remote side fails to acknowledge the link establishment
request in time or completely. At some point gsm_dlci_close() is called
to abort the link establishment attempt. The function tries to inform the
associated virtual tty by performing a hangup. But the blocking loop within
tty_port_block_til_ready() is not informed about this event.
The patch proposed here fixes this by resetting the initialization state of
the virtual tty to ensure the loop exits and triggering it to make
tty_port_block_til_ready() return.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function gsm_process_modem() exists to handle modem status bits of
incoming frames. This includes incoming MSC (modem status command) frames
and convergence layer type 2 data frames. The function, however, was only
designed to handle MSC frames as it expects the command length. Within
gsm_dlci_data() it is wrongly assumed that this is the same as the data
frame length. This is only true if the data frame contains only 1 byte of
payload.
This patch names the length parameter of gsm_process_modem() in a generic
manner to reflect its association. It also corrects all calls to the
function to handle the variable number of modem status octets correctly in
both cases.
Fixes: 7263287af9 ("tty: n_gsm: Fixed logic to decode break signal from modem status")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty flow control is handled via gsmtty_throttle() and gsmtty_unthrottle().
Both functions propagate the outgoing hardware flow control state to the
remote side via MSC (modem status command) frames. The local state is taken
from the RTS (ready to send) flag of the tty. However, RTS gets mapped to
DTR (data terminal ready), which is wrong.
This patch corrects this by mapping RTS to RTS.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The here fixed commit made the tty hangup asynchronous to avoid a circular
locking warning. I could not reproduce this warning. Furthermore, due to
the asynchronous hangup the function call now gets queued up while the
underlying tty is being freed. Depending on the timing this results in a
NULL pointer access in the global work queue scheduler. To be precise in
process_one_work(). Therefore, the previous commit made the issue worse
which it tried to fix.
This patch fixes this by falling back to the old behavior which uses a
blocking tty hangup call before freeing up the associated tty.
Fixes: 7030082a74 ("tty: n_gsm: avoid recursive locking with async port hangup")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.1.2 describes the encoding of the
C/R (command/response) bit. Table 1 shows that the actual encoding of the
C/R bit is inverted if the associated frame is sent by the responder.
The referenced commit fixed here further broke the internal meaning of this
bit in the outgoing path by always setting the C/R bit regardless of the
frame type.
This patch fixes both by setting the C/R bit always consistently for
command (1) and response (0) frames and inverting it later for the
responder where necessary. The meaning of this bit in the debug output
is being preserved and shows the bit as if it was encoded by the initiator.
This reflects only the frame type rather than the encoded combination of
communication side and frame type.
Fixes: cc0f42122a ("tty: n_gsm: Modify CR,PF bit when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patches, noone needs 'file' parameter in neither
ioctl hook from tty_ldisc_ops. So remove 'file' from both of them.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> [NFC]
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122094529.24171-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have gsmld_output() ignore the return value from device
write. This means we will lose packets if device write returns 0 or
an error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210930060624.46523-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two lines need to be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211004104343.GF25015@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch, there are no users of 'file' in
n_tty_ioctl_helper. So remove it also from there.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As requester,because n_gsm has no uevent report for application,the
application can't know dlci connect or disconnect.
The application will control every dlcl dev by uevent,when application
receive gsmtty0 dev remove uevent,it will close mux function,and change to
normal mode.
Example:
Before modify:
gsmld receive DLC0 DISC,no event report to application
gsmld receive DLC1 SABM,no event report to application
gsmld receive DLC1 DISC,no event report to application
After modify:
Receive DLC0 DISC,report "/devices/virtual/tty/gsmtty0" remove uevent
Receive DLC1 SABM,report "/devices/virtual/tty/gsmtty1" add uevent
Receive DLC1 DISC,report "/devices/virtual/tty/gsmtty1" remove uevent
Signed-off-by: Zhenguo Zhao <Zhenguo.Zhao1@unisoc.com>
Link: https://lore.kernel.org/r/1629461872-26965-7-git-send-email-zhenguo6858@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When n_gsm config "initiator=0",when gsmld config ,as requester ,it
doesn't need to send CLD frame data or SABM frame.
Example,when tty dev receive "AT+CMUX=0",it will change ldisc
n_tty to n_gsm,during config requester,gsmld output "7e 01 ef c3 aa 7e",
initiator maybe not want to receive the frame data.
[ 154.666457] c1 Q> 0) R: UIH(F)
[ 154.669514] c1 C3
[ 154.671519] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
[ 155.014874] c1 Q> 0) R: UIH(F)
[ 155.018000] c1 C3
[ 155.020046] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
[ 155.364425] c1 Q> 0) R: UIH(F)
[ 155.367546] c1 C3
[ 155.369597] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
Signed-off-by: Zhenguo Zhao <Zhenguo.Zhao1@unisoc.com>
Link: https://lore.kernel.org/r/1629461872-26965-5-git-send-email-zhenguo6858@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68e (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/n_gsm.c:525: warning: expecting prototype for gsm_stuff_packet(). Prototype was for gsm_stuff_frame() instead
drivers/tty/n_gsm.c:1608: warning: expecting prototype for gsm_dlci_control(). Prototype was for gsm_dlci_command() instead
drivers/tty/n_gsm.c:2561: warning: Function parameter or member 'cookie' not described in 'gsmld_read'
drivers/tty/n_gsm.c:2561: warning: Function parameter or member 'offset' not described in 'gsmld_read'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210520121906.3468725-11-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_unregister_ldisc now returns 0 = success. No need to check the
return value. In fact, the users only warned if an error occured and
didn't do anything useful anyway -- the ldisc module was unloaded in any
case.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make tty_unregister_ldisc symmetric to tty_register_ldisc by accepting
struct tty_ldisc_ops as a parameter instead of ldisc number. This avoids
checking of the ldisc number bounds in tty_unregister_ldisc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the classic failpath handling using gotos in gsm_init. That way,
tty_unregister_ldisc needs not be repeated on two places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210505091928.22010-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to pass the ldisc number to tty_register_ldisc
separately. Just set it in the already defined tty_ldisc_ops in all the
ldiscs.
This simplifies tty_register_ldisc a bit too (no need to set the num
member there).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Link: https://lore.kernel.org/r/20210505091928.22010-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Char pointer (cp) passed to tty_ldisc_ops::receive_buf{,2} is const.
There is no reason for flag pointer (fp) not to be too. So switch it in
the definition and all uses.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a lot of tty-core-only functions that are listed in
include/linux/tty.h. Move them to drivers/tty/tty.h so that no one else
can accidentally call them or think that they are public functions.
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20210408125134.3016837-14-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Link: https://lore.kernel.org/r/1617710163-48158-1-git-send-email-huangguobin4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty line disciplines don't expect tty_operations::write_room to
return negative values. Fix the five drivers which violate this.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-44-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty line disciplines don't expect tty_operations::chars_in_buffer to
return negative values. Fix the two drivers which violate this.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-43-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dp, f, and i are only duplicates of gsmld_receive_buf's parameters. Use
the parameters directly (cp, fp, and count) and delete these local
variables.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-41-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, it is never checked. Second, use of it as a debugging aid is
at least questionable. With the current tools, I don't think anyone used
this kind of thing for debugging purposes for years.
On the top of that, e.g. serdev does not set this field of tty_ldisc_ops
at all.
So get rid of this legacy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes both the "splice/sendfile to a tty" and "splice/sendfile from a
tty" regression from 5.10.
* 'tty-splice' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
tty: implement write_iter
The tty line discipline .read() function was passed the final user
pointer destination as an argument, which doesn't match the 'write()'
function, and makes it very inconvenient to do a splice method for
ttys.
This is a conversion to use a kernel buffer instead.
NOTE! It does this by passing the tty line discipline ->read() function
an additional "cookie" to fill in, and an offset into the cookie data.
The line discipline can fill in the cookie data with its own private
information, and then the reader will repeat the read until either the
cookie is cleared or it runs out of data.
The only real user of this is N_HDLC, which can use this to handle big
packets, even if the kernel buffer is smaller than the whole packet.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/n_gsm.c:85: warning: Function parameter or member 'ref' not described in 'gsm_mux_net'
drivers/tty/n_gsm.c:85: warning: Function parameter or member 'dlci' not described in 'gsm_mux_net'
drivers/tty/n_gsm.c:664: warning: Function parameter or member 'dlci' not described in 'gsm_data_kick'
drivers/tty/n_gsm.c:1015: warning: Function parameter or member 'clen' not described in 'gsm_process_modem'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-19-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm->output and ->error are set only to gsmld_output and gsm_error,
respectively. Call these functions directly and remove error and output
function pointers from struct gsm_mux completely.
Note: we need a forward declaration of gsmld_output now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085655.12071-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the length is zero then the print_hex_dump_bytes won't output
anything, so testing the length before the call is unnecessary.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-2-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both gsm_dlci->constipated and gsm_mux->constipated are used as bools,
so treat them as such.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219084949.28074-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both gsm_dlci->dead and gsm_mux->dead are used as bools, so treat them
as such.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219084949.28074-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_mux->state is clearly an enumeration. So introduce one and use it
-- compiler now checks if valid values are assigned to the field.
Note that a compiler warns about unhandled cases in switch. Add default
cases with a pr_debug (which is not printed by default).
The values of the states are preserved thanks to the nature of enum.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219084949.28074-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_dlci->mode is clearly an enumeration. So introduce one and use it
-- compiler now checks if valid values are assigned to the field.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219084949.28074-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_dlci->state is clearly an enumeration. So introduce one and use it
-- compiler now checks if valid values are assigned to the field.
Note that a compiler warns about unhandled cases in switch. Add default
cases with a pr_debug (which is not printed by default).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219084949.28074-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_dlci->fifo always points to gsm_dlci->_fifo. So drop the pointer and
rename _fifo to fifo. And update all the users (add & to them).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219084949.28074-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200212193523.GA28826@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guessing the first tty for a gsm0710 multiplexed serial device is not
currently possible, which makes it racy to use with multiple modems.
Add a way to map the physical serial tty to its related mux devices
using an ioctl.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20190812211243.98686-1-martin@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it obvious how the gsm mux number relates to the virtual tty lines
by using helper functions instead of shifting 6 bits.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20190710192656.60381-3-martin@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/tty/n_gsm.c: In function ‘gsm_dlci_data’:
drivers/tty/n_gsm.c:1582:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (tty) {
^
drivers/tty/n_gsm.c:1587:2: note: here
case 1:
^~~~
drivers/tty/n_gsm.c: In function ‘gsm1_receive’:
CC [M] drivers/scsi/snic/snic_disc.o
CC [M] drivers/net/wireless/realtek/rtlwifi/pci.o
CC drivers/usb/early/xhci-dbc.o
drivers/tty/n_gsm.c:1981:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
gsm->fcs = INIT_FCS;
^
drivers/tty/n_gsm.c:1983:2: note: here
case GSM_ADDRESS: /* Address continuation */
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to prepare for adding serdev driver support, let's constify
the use of u8 and unsigned char for n_gsm.
Note that gsm_control_modem() gsm_control_rls() read the data for tty
control characters and then call gsm_control_reply() that allocates a
new reply and copies the data.
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For supporting serdev drivers, we need to be able to configure n_gsm
from drivers. Let's prepare for that by adding copy_config() and
gsm_config() helper functions by moving the code around a bit.
Let's also unify the comments to keep checkpatch happy while at it.
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First of all, make it return int. Returning long when native method
had never allowed that is ridiculous and inconvenient.
More importantly, change the caller; if ldisc ->compat_ioctl() is NULL
or returns -ENOIOCTLCMD, tty_compat_ioctl() will try to feed cmd and
compat_ptr(arg) to ldisc's native ->ioctl().
That simplifies ->compat_ioctl() instances quite a bit - they only
need to deal with ioctls that are neither generic tty ones (those
would get shunted off to tty_ioctl()) nor simple compat pointer ones.
Note that something like TCFLSH won't reach ->compat_ioctl(),
even if ldisc ->ioctl() does handle it - it will be recognized
earlier and passed to tty_ioctl() (and ultimately - ldisc ->ioctl()).
For many ldiscs it means that NULL ->compat_ioctl() does the
right thing. Those where it won't serve (see e.g. n_r3964.c) are
also easily dealt with - we need to handle the numeric-argument
ioctls (calling the native instance) and, if such would exist,
the ioctls that need layout conversion, etc.
All in-tree ldiscs dealt with.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on droid 4 with control channel in ADM mode, there is no response
to Modem Status Command (MSC). Currently gsmtty_modem_update() expects to
have data in dlci->modem_rx unless debug & 2 is set. This means that on
droid 4, things only work if debug & 2 is set.
Let's fix the issue by ignoring empty dlci->modem_rx for ADM mode. In
the AMD mode, CMD_MSC will never respond and gsm_process_modem() won't
get called to set dlci->modem_rx.
And according to ts_127010v140000p.pdf, MSC is only relevant if basic
option is chosen, so let's test for that too.
Fixes: ea3d8465ab ("tty: n_gsm: Allow ADM response in addition to UA for control dlci")
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ea3d8465ab ("tty: n_gsm: Allow ADM response in addition to UA for
control dlci") added support for DLCI to stay in Asynchronous Disconnected
Mode (ADM). But we still get long delays waiting for commands to other
DLCI to complete:
--> 5) C: SABM(P)
Q> 0) C: UIH(F)
Q> 0) C: UIH(F)
Q> 0) C: UIH(F)
...
This happens because gsm_control_send() sets cretries timer to T2 that is
by default set to 34. This will cause resend for T2 times for the control
frame. In ADM mode, we will never get a response so the control frame, so
retries are just delaying all the commands.
Let's fix the issue by setting DLCI_MODE_ADM flag after detecting the ADM
mode for the control DLCI. Then we can use that in gsm_control_send() to
set retries to 1. This means the control frame will be sent once allowing
the other end at an opportunity to switch from ADM to ABM mode.
Note that retries will be decremented in gsm_control_retransmit() so
we don't want to set it to 0 here.
Fixes: ea3d8465ab ("tty: n_gsm: Allow ADM response in addition to UA for control dlci")
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big tty/serial driver update for 4.16-rc1.
The usual number of various serial driver fixes and updates to try to
get them to work with crazy hardware configurations (seriously, how many
different ways are hardware engineers going to come up with to hook up a
simple UART?)
There is also some serdev bugfixes and updates, as well as a smattering
of other small fixes in here.
All have been in the linux-next tree for a while, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLyuw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylItQCgncAzYeOJ9IXY/wEnmIJS7sPzeMkAnimmYddW
Z5d3SAbe9drdGs6BOr5e
=h8ad
-----END PGP SIGNATURE-----
Merge tag 'tty-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/staging driver updates from Greg KH:
"Here is the big tty/serial driver update for 4.16-rc1.
The usual number of various serial driver fixes and updates to try to
get them to work with crazy hardware configurations (seriously, how
many different ways are hardware engineers going to come up with to
hook up a simple UART?)
There is also some serdev bugfixes and updates, as well as a
smattering of other small fixes in here.
All have been in the linux-next tree for a while, with no reported
issues"
* tag 'tty-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: exar: Relocate sleep wake-up handling
tty: fix data race between tty_init_dev and flush of buf
serial: imx: fix endless loop during suspend
serial: core: mark port as initialized after successful IRQ change
serdev: only match serdev devices
serdev: do not generate modaliases for controllers
serial: mxs-auart: don't use GPIOF_* with gpiod_get_direction
serial: 8250_dw: Revert "Improve clock rate setting"
MAINTAINERS: Add myself as designated reviewer for 8250_dw
gpio: serial: max310x: Support open-drain configuration for GPIOs
serdev: Fix serdev_uevent failure on ACPI enumerated serdev-controllers
serial: 8250_ingenic: Parse earlycon options
serial: 8250_ingenic: Add support for the JZ4770 SoC
serial: core: Make uart_parse_options take const char* argument
serial: 8250_of: fix return code when probe function fails to get reset
serial: imx: Only wakeup via RTSDEN bit if the system has RTS/CTS
serial: 8250_uniphier: fix error return code in uniphier_uart_probe()
tty: n_gsm: Allow ADM response in addition to UA for control dlci
tty: omap-serial: Fix initial on-boot RTS GPIO level
tty: serial: jsm: Add one check against NULL pointer dereference
...
Some devices have the control dlci stay in ADM mode instead of the UA
mode. This can seen at least on droid 4 when trying to open the ts
27.010 mux port. Enabling n_gsm debug mode shows the control dlci
always respond with DM to SABM instead of UA:
# modprobe n_gsm debug=0xff
# ldattach -d GSM0710 /dev/ttyS0 &
gsmld_output: 00000000: f9 03 3f 01 1c f9
--> 0) C: SABM(P)
gsmld_receive: 00000000: f9 03 1f 01 36 f9
<-- 0) C: DM(P)
...
$ minicom -D /dev/gsmtty1
minicom: cannot open /dev/gsmtty1: No error information
$ strace minicom -D /dev/gsmtty1
...
open("/dev/gsmtty1", O_RDWR|O_NOCTTY|O_NONBLOCK|O_LARGEFILE) = -1 EL2HLT
Note that this is different issue from other n_gsm -EL2HLT issues such
as timeouts when the control dlci does not respond at all.
The ADM mode seems to be a quite common according to "RF Wireless World"
article "GSM Issue-UE sends SABM and gets a DM response instead of
UA response":
This issue is most commonly observed in GSM networks where in UE sends
SABM and expects network to send UA response but it ends up receiving
DM response from the network. SABM stands for Set asynchronous balanced
mode, UA stands for Unnumbered Acknowledge and DA stands for
Disconnected Mode.
An RLP entity can be in one of two modes:
- Asynchronous Balanced Mode (ABM)
- Asynchronous Disconnected Mode (ADM)
Currently Linux kernel closes the control dlci after several retries
in gsm_dlci_t1() on DM. This causes n_gsm /dev/gsmtty ports to produce
error code -EL2HLT when trying to open them as the closing of control
dlci has already set gsm->dead.
Let's fix the issue by allowing control dlci stay in ADM mode after the
retries so the /dev/gsmtty ports can be opened and used. It seems that
it might take several attempts to get any response from the control
dlci, so it's best to allow ADM mode only after the SABM retries are
done.
Note that for droid 4 additional patches are needed to mux the ttyS0
pins and to toggle RTS gpio_149 to wake up the mdm6600 modem are also
needed to use n_gsm. And the mdm6600 modem needs to be powered on.
Cc: linux-serial@vger.kernel.org
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: Jiri Prchal <jiri.prchal@aksignal.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer gsm is assigned a value that is never read, hence it is
redundant and can be removed. Cleans up clang warning:
drivers/tty/n_gsm.c:2979:2: warning: Value stored to 'gsm' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use this driver with 32 bit userspace applications on 64 bit
kernels a compat_ioctl is needed.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gsm_cleanup_mux() is called in the line discipline close path which
is called at tty_release() time. At this stage the tty is no longer
operational enough to send any frames. Sending close frames is
therefore not possible and waiting for their answers always times
out.
This patch removes sending close messages and waiting for their answers
from the tty_release path.
This patch makes explicit what previously implicitly had been the case
already: We are not able to tell the modem that we are about to close
the multiplexer on our side. This means the modem will stay in
multiplexer mode and re-establishing the multiplexer later fails. The
only way for userspace to work around this is to manually send a close
frame in N_TTY mode after closing the mux.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a private copy of struct net_device_stats in struct
gsm_mux_net, use stats from struct net_device. Also remove
the now unnecessary .ndo_get_stats function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: Maya Erez <qca_merez@qca.qualcomm.com>
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Stanislav Yakovlev <stas.yakovlev@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
[<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
[<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
[<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
[<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
[<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...
But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.
Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expressions of the form "tty->termios.c_*flag & FLAG"
are more clearly expressed with the termios flags macros,
I_FLAG(), C_FLAG(), O_FLAG(), and L_FLAG().
Convert treewide.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chars_in_buffer() line discipline method serves no functional
purpose, other than as a (dubious) debugging aid for mostly bit-rotting
drivers. Despite being documented as an optional method, every caller
is unconditionally executed (although conditionally compiled).
Furthermore, direct tty->ldisc access without an ldisc ref is unsafe.
Lastly, N_TTY's chars_in_buffer() has warned of removal since 3.12.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In little endian cases, macro htons unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_htons and htons expand directly to the same expression.
So, replace __constant_htons with htons with the goal of getting
rid of the definition of __constant_htons completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_htons(x)
+ htons(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when gsmtty_remove put dlci, it will cause memory leak if dlci->port's refcount is zero.
So we do the cleanup work in .cleanup callback instead.
dlci will be last put in two call chains.
1) gsmld_close -> gsm_cleanup_mux -> gsm_dlci_release -> dlci_put
2) gsmld_remove -> dlci_put
so there is a race. the memory leak depends on the race.
In call chain 2. we hit the memory leak. below comment tells.
release_tty -> tty_driver_remove_tty -> gsmtty_remove -> dlci_put -> tty_port_destructor (WARN_ON(port->itty) and return directly)
|
tty->port->itty = NULL;
|
tty_kref_put ---> release_one_tty -> gsmtty_cleanup (added by our patch)
So our patch fix the memory leak by doing the cleanup work after tty core did.
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Fixes: dfabf7ffa3
Cc: stable <stable@vger.kernel.org> # 3.14+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_name no longer uses the buf parameter, so remove it along with all
the 64 byte stack buffers that used to be passed in.
Mostly generated by the coccinelle script
@depends on patch@
identifier buf;
constant C;
expression tty;
@@
- char buf[C];
<+...
- tty_name(tty, buf)
+ tty_name(tty)
...+>
allmodconfig compiles, so I'm fairly confident the stack buffers
weren't used for other purposes as well.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The result of netdev_priv is already implicitly cast to the type of the
left side of the assignment.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
@@
x =
- (T *)
netdev_priv(...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch fixes following sparse warning:
n_gsm.c:2827:22: warning: symbol 'tty_ldisc_packet' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
If gsmld_attach_gsm fails, the gsm is not used anymore.
tty core will not call gsmld_close to do the cleanup work.
tty core just restore to the tty old ldisc.
That always causes memory leak.
Signed-off-by: xinhui.pan <xinhuiX.pan@intel.com>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just a simple cleanup of init_timer with setting the fields manually.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm->num is the index of gsm_mux[], it's invalid before calling gsm_activate_mux.
Signed-off-by: xinhui.pan <xinhuiX.pan@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3GPP TS 07.10 states in section 5.4.6.3.7:
"The length byte contains the value 2 or 3 ... depending on the break
signal." The break byte is optional and if it is sent, the length is
3. In fact the driver was not able to work with modems that send this
break byte in their modem status control message. If the modem just
sends the break byte if it is really set, then weird things might
happen.
The code for deconding the modem status to the internal linux
presentation in gsm_process_modem has already a big comment about
this 2 or 3 byte length thing and it is already able to decode the
brk, but the code calling the gsm_process_modem function in
gsm_control_modem does not encode it and hand it over the right way.
This patch fixes this.
Without this fix if the modem sends the brk byte in it's modem status
control message the driver will hang when opening a muxed channel.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marks the functions gsm_cleanup_mux(), gsm_activate_mux(),
gsm_free_mux(), gsm_alloc_mux() and gsm_change_mtu() as static in
n_gsm.c because they are not used outside this file.
Also, drop the EXPORT_SYMBOL_GPL for the above mentioned functions
because nothing else in the kernel calls them.
This eliminates the following warnings in n_gsm.c:
drivers/tty/n_gsm.c:2022:6: warning: no previous prototype for ‘gsm_cleanup_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2076:5: warning: no previous prototype for ‘gsm_activate_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2120:6: warning: no previous prototype for ‘gsm_free_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2156:17: warning: no previous prototype for ‘gsm_alloc_mux’ [-Wmissing-prototypes]
drivers/tty/n_gsm.c:2714:5: warning: no previous prototype for ‘gsm_change_mtu’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyA has ld associated to n_gsm, when ttyA is closing, it triggers
to release gsmttyB's ld data dlci[B], then race would happen if gsmttyB
is opening in parallel.
(Note: This patch set differs from previous set in that it uses mutex
instead of spin lock to avoid race, so that it avoids sleeping in automic
context)
Here are race cases we found recently in test:
CASE #1
====================================================================
releasing dlci[B] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(gsmttyB), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[B]) -----
| |
gsm_dlci_free(dlci[B]) -----
| |
----- gsmtty_open(gsmttyB)
gsmtty_open()
{
struct gsm_dlci *dlci = tty->driver_data; => here it uses dlci[B]
...
}
In gsmtty_open(gsmttyA), it uses dlci[B] which was release, so hit a panic.
=====================================================================
CASE #2
=====================================================================
releasing dlci[0] race with gsmtty_install(gsmttyB), then panic
in gsmtty_open(), as below:
tty_release(ttyA) tty_open(gsmttyB)
| |
----- gsmtty_install(gsmttyB)
| |
----- gsm_dlci_alloc(gsmttyB) => alloc dlci[B]
| |
----- gsmtty_open(gsmttyB) fail
| |
----- tty_release(gsmttyB)
| |
----- gsmtty_close(gsmttyB)
| |
----- gsmtty_detach_dlci(dlci[B])
| |
----- dlci_put(dlci[B])
| |
tty_ldisc_release(ttyA) -----
| |
gsm_dlci_release(dlci[0]) -----
| |
gsm_dlci_free(dlci[0]) -----
| |
----- dlci_put(dlci[0])
In gsmtty_detach_dlci(dlci[B]), it tries to use dlci[0] which was released,
then hit panic.
=====================================================================
IMHO, n_gsm tty operations would refer released ldisc, as long as
gsm_dlci_release() has chance to release ldisc data when some gsmtty operations
are ongoing..
This patch is try to avoid it by:
1) in n_gsm driver, use a global gsm mutex lock to avoid gsm_dlci_release() run in
parallel with gsmtty_install();
2) Increase dlci's ref count in gsmtty_install() instead of in gsmtty_open(), the
purpose is to prevent gsm_dlci_release() releasing dlci after gsmtty_install()
allocats dlci but before gsmtty_open increases dlci's ref count;
3) Decrease dlci's ref count in gsmtty_remove(), a tty framework API, this is the
opposite process of step 2).
Signed-off-by: Chao Bi <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most line disciplines already handle the undocumented NULL flag
ptr in their .receive_buf method; however, several don't.
Document the NULL flag ptr, and correct handling in the
N_MOUSE, N_GSM0710 and N_R394 line disciplines.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specifically:
n_gsm.c:810: ERROR: space required before the open parenthesis '('
n_gsm.c:830: WARNING: line over 80 characters
n_gsm.c:971: ERROR: trailing whitespace
n_gsm.c:984: ERROR: code indent should use tabs where possible
n_gsm.c:984: WARNING: please, no space before tabs
n_gsm.c:984: WARNING: please, no spaces at the start of a line
n_gsm.c:1141: WARNING: space prohibited before semicolon
n_gsm.c:1743: ERROR: space required before the open brace '{'
n_gsm.c:1744: WARNING: line over 80 characters
n_gsm.c:1745: ERROR: code indent should use tabs where possible
n_gsm.c:1746: ERROR: code indent should use tabs where possible
n_gsm.c:2908: WARNING: line over 80 characters
n_gsm.c:2912: ERROR: trailing whitespace
Signed-off-by: Aldo Iljazi <neonsync1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move HUPCL handling to port shutdown so that DTR is dropped also on hang
up (tty_port_close is a noop for hung-up ports).
Also do not try to drop DTR for uninitialised ports where it has never
been raised (e.g. after a failed open).
Note that this is also the current behaviour of serial-core.
Nine drivers currently call tty_port_close_start directly (rather than
through tty_port_close) and seven of them lower DTR as part of their
close (if the port has been initialised). Fixup the remaining two
drivers so that it continues to be lowered also on normal (non-HUP)
close. [ Note that most of those other seven drivers did not expect DTR
to have been dropped by tty_port_close_start in the first place. ]
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes a deadlock when the multiplexer is closed while there
are still client side ports open.
When the multiplexer is closed and there are active tty's it tries to
close them with tty_vhangup. This has a problem though, because
tty_vhangup needs the tty_lock. This patch changes it to unlock the
tty_lock before attempting the hangup and relocks afterwards. The
additional call to tty_port_tty_set is needed because otherwise the
port stays active because of the reference counter.
This change also exposed another problem that other code paths don't
expect that the multiplexer could have been closed. This patch also adds
checks for these cases in the gsmtty_ class of function that could be
called.
The documentation explicitly states that "first close all virtual ports
before closing the physical port" but we've found this to not always
reality in our field situations. The GPRS / UTMS modem sometimes crashes
and needs a power cycle in that case which means cleanly shutting down
everything is not always possible. This change makes it much more robust
for our situation where at least the system is recoverable with this patch
and doesn't hang in a deadlock situation inside the kernel.
The patch is against the long term support kernel (3.4.27) and should
apply cleanly to more recent branches. Tested with a Telit GE864-QUADV2
and Telit HE910 modem.
Signed-off-by: Dirkjan Bussink <dirkjan.bussink@nedap.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f96f7f7f39, at the
request of Jin.
Cc: xiaojin <jin.xiao@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the call to gsm->output should be in the tx_lock,
that could avoid potential race from MUX level. But
we have no tx_lock in gsm_send.
This patch is to add tx_lock in gsm_send.
Signed-off-by: xiaojin <jin.xiao@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
Here it is enough to switch to refcounting in tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the trace we print the wrong values for N(R) on an I frame.
Correct the mask.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uplink (TX) network data will go through gsm_dlci_data_output_framed
there is a bug where if memory allocation fails, the skb which
has already been pulled off the list will be lost.
In addition TX skbs were being processed in LIFO order
Fixed the memory leak, and changed to FIFO order processing
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Showjumping <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are supposed to use the dev_* versions of the kfree_skb
interfaces. In a couple of cases we were called with IRQs
disabled as well which kfree_skb() does not expect.
Replaced kfree_skb calls w/ dev_kfree_skb and dev_kfree_skb_any
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Grooming <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_data_kick was recently modified to allow messages on the
tx queue bound for DLCI0 to flow even during FCOFF conditions.
Unfortunately we introduced a bug discovered by code inspection
where subsequent list traversers can access freed memory if
the DLCI0 messages were not all at the head of the list.
Replaced singly linked tx list w/ a list_head and used
provided interfaces for traversing and deleting members.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were some locking holes in the management of the MUX's
message queue for 2 code paths:
1) gsmld_write_wakeup
2) receipt of CMD_FCON flow-control message
In both cases gsm_data_kick is called w/o locking so it can collide
with other other instances of gsm_data_kick (pulling messages tx_tail)
or potentially other instances of __gsm_data_queu (adding messages to tx_head)
Changed to take the tx_lock in these 2 cases
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The design of uplink flow control in the mux driver is
that for constipated channels data will backup into the
per-channel fifos, and any messages that make it to the
outbound message queue will still go out.
Code was added to also stop messages that were in the outbound
queue but this requires filtering through all the messages on the
queue for stopped dlcis and changes some of the mux logic unneccessarily.
The message fiiltering was removed to be in line w/ the original design
as the message filtering does not provide any solution.
Extra debug messages used during investigation were also removed.
Signed-off-by: samix.lebsir <samix.lebsir@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Dressage <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Correcting handling of FCon/FCoff in order to respect 27.010 spec
- Consider FCon/off will overide all dlci flow control except for
dlci0 as we must be able to send control frames.
- Dlci constipated handling according to FC, RTC and RTR values.
- Modifying gsm_dlci_data_kick and gsm_dlci_data_sweep according
to dlci constipated value
Signed-off-by: Frederic Berat <fredericx.berat@intel.com>
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_dlci_data_kick will not call any output function if tx_bytes > THRESH_LO
furthermore it will call the output function only once if tx_bytes == 0
If the size of the IP writes are on the order of THRESH_LO
we can get into a situation where skbs accumulate on the outbound list
being starved for events to call the output function.
gsm_dlci_data_kick now calls the sweep function when tx_bytes==0
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Hay and Water <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3GPP27.010 5.8.1, it defined:
The TE multiplexer initiates the establishment of the multiplexer control channel by sending a SABM frame on DLCI 0 using the procedures of clause 5.4.1.
Once the multiplexer channel is established other DLCs may be established using the procedures of clause 5.4.1.
This patch implement 5.8.1 in MUX level, it make sure DLC0 is the first channel to be setup.
[or for those not familiar with the specification: it was possible to try
and open a data connection while the control channel was not yet fully
open, which is a spec violation and confuses some modems]
Signed-off-by: xiaojin <jin.xiao@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
[tweaked the order we check things and error code]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: The Horsebox <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to link a port to a tty in install. And since dlci is
allocated even in open, we need to create gsmtty_install, allocate
dlci there and create also the link.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alek Du reported that the code erroneously applies time to jiffies
conversions twice to the t1 and t2 values. In normal use on a modem link
this cases no visible problem but on a slower link it will break as with
HZ=1000 as is typical we are running t1/t2 ten times too fast.
Alek's original patch removed the conversion from the timer setting but we
in fact have to be more careful as the contents of t1/t2 are visible via
the device API and we thus need to correct the constants.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
n_gsm use a simple approach: every writing to fifo correspond exactly one
reading from fifo. There are no problem in this approach until we read
less bytes then we write. As result fifo may owerflow. This leads to packet
loss and very slow responce.
For example, this happens with ping packets (about 96 byte each) and default
gsm->mtu = 64. As result we get 50 sec ping timeout and 20% packet loss.
Fix the problem by reading and sending all data from the fifo
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in adaption=2 case we should put 1 or 2 byte with modem status bits
at the beginning of a buffer pointed by "dp". n_gsm use 1 byte case,
so it allocate a buffer of len + 1 size. As result we should:
* put 1 byte of modem status bits
* increase data pointer
* put "len" bytes of data
but actually we have:
* increase first byte with the value of modem status bits
* decrease "len"
* put orig_len - 1 bytes of data starting from the buffer beggining
This is evidently wrong.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A DISC on DLCI 0 should close down the mux but Michael Lauer reports this
is not the case for some modems. Send a CLD as well.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Michael Lauer
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (26 commits)
amba pl011: workaround for uart registers lockup
n_gsm: fix the wrong FCS handling
pch_uart: add missing comment about OKI ML7223
pch_uart: Add MSI support
tty: fix "IRQ45: nobody cared"
PTI feature to allow user to name and mark masterchannel request.
0 for o PTI Makefile bug.
tty: serial: samsung.c remove legacy PM code.
SERIAL: SC26xx: Fix link error.
serial: mrst_max3110: initialize waitqueue earlier
mrst_max3110: Change max missing message priority.
tty: s5pv210: Add delay loop on fifo reset function for UART
tty/serial: Fix XSCALE serial ports, e.g. ce4100
serial: bfin_5xx: fix off-by-one with resource size
drivers/tty: use printk_ratelimited() instead of printk_ratelimit()
tty: n_gsm: Added refcount usage to gsm_mux and gsm_dlci structs
tty: n_gsm: Add raw-ip support
tty: n_gsm: expose gsmtty device nodes at ldisc open time
pch_phub: Fix register miss-setting issue
serial: 8250, increase PASS_LIMIT
...
FCS could be GSM0_SOF, so will break state machine...
[This byte isn't quoted in any way so a SOF here doesn't imply an error
occurred.]
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org> [3.0]
[Trivial but best backported once its in 3.1rc I think]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The gsm_mux is created/destroyed when ldisc is
opened/closed but clients of the MUX channel devices (gsmttyN)
may access this structure as long as the TTYs are open.
For the open, the ldisc open is guaranteed to preceed the TTY open,
but the close has no such guaranteed ordering. As a result,
the gsm_mux can be freed in the ldisc close before being accessed
by one of the TTY clients. This can happen if the ldisc is removed
while there are open, active MUX channels.
A similar situation exists for DLCI-0, it is basically a resource
shared by MUX and DLCI , and should not be freed while they can
be accessed
To avoid this, gsm_mux and dlcis now have a reference counter
ldisc open takes a reference on the mux and all the dlcis
gsmtty_open takes a reference on the mux, dlci0 and its specific
dlci. Dropping the last reference initiates the actual free.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the ability to open a network data connection over a mux
virtual tty channel. This is for modems that support data connections
with raw IP frames instead of PPP. On high speed data connections this
eliminates a significant amount of PPP overhead. To use this interface,
the application must first tell the modem to open a network connection on
a virtual tty. Once that has been accomplished, the app will issue an
IOCTL on that virtual tty to create the network interface. The IOCTL will
return the index of the interface created.
The two IOCTL commands are:
ioctl( fd, GSMIOC_ENABLE_NET );
ioctl( fd, GSMIOC_DISABLE_NET );
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
