Most systems' PCIe outbound map windows have non-zero physical addresses,
but the possibility of encountering zero increased after following commit
("PCI: dwc: Use parent_bus_offset").
'ep->outbound_addr[n]', representing 'parent_bus_address', might be 0 on
some hardware, which trims high address bits through bus fabric before
sending to the PCIe controller.
Replace the iteration logic with 'for_each_set_bit()' to ensure only
allocated map windows are iterated when determining the ATU index from a
given address.
Link: https://lore.kernel.org/r/20250315201548.858189-12-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Endpoint
┌───────────────────────────────────────────────┐
│ pcie-ep@5f010000 │
│ ┌────────────────┐│
│ │ Endpoint ││
│ │ PCIe ││
│ │ Controller ││
│ bus@5f000000 │ ┌────────►
│ ┌──────────┐ │ │ ││dynamically
│ │ │ Outbound Transfer │ ││allocated
│┌─────┐ │ Bus ┼─────►│ ATU ───────┘ ││PCI Addr
││ │ │ Fabric │Bus │ ││
││ CPU ├───►│ │Addr │ ││
││ │CPU │ │0x8000_0000 ││
│└─────┘Addr└──────────┘ │ ││
│ 0x7000_0000 └────────────────┘│
└───────────────────────────────────────────────┘
bus@5f000000 {
compatible = "simple-bus";
ranges = <0x80000000 0x0 0x70000000 0x10000000>;
pcie-ep@5f010000 {
reg = <0x80000000 0x10000000>;
reg-names ="addr_space";
...
};
...
};
In the diagram above, CPU writes data to outbound window address
0x7000_0000, and the bus fabric maps it to 0x8000_0000. The ATU uses
bus address 0x8000_0000 as input address and maps to some PCI address
dynamically allocated by a PCI device driver on the host side.
The pcie-ep@5f010000 'reg[addr_space]' is the parent bus address, which is
the input of PCIe controller, including the ATU.
Set parent_bus_offset, the offset from the CPU address to the PCIe
controller input address using dw_pcie_init_parent_bus_offset(). The
parent_bus_offset is not used yet, so no functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20250315201548.858189-11-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move devm_pci_epc_create() to the beginning of dw_pcie_ep_init().
devm_pci_epc_create() is generic code that doesn't depend on any DWC
resource, so moving it earlier keeps all the subsequent devicetree-related
code together.
Link: https://lore.kernel.org/r/20250315201548.858189-9-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
The 'ranges' property of a PCI controller's parent can indicate address
translation information. Most system use 1:1 map between CPU physical and
PCI controller input addresses.
But some hardware, like i.MX8QXP, doesn't use 1:1 map. See below diagram:
┌─────────┐ ┌────────────┐
┌─────┐ │ │ IA: 0x8ff8_0000 │ │
│ CPU ├───►│ ┌────►├─────────────────┐ │ PCI │
└─────┘ │ │ │ IA: 0x8ff0_0000 │ │ │
CPU Addr │ │ ┌─►├─────────────┐ │ │ Controller │
0x7ff8_0000─┼───┘ │ │ │ │ │ │
│ │ │ │ │ │ │ PCI Addr
0x7ff0_0000─┼──────┘ │ │ └──► IOSpace ─┼────────────►
│ │ │ │ │ 0
0x7000_0000─┼────────►├─────────┐ │ │ │
└─────────┘ │ └──────► CfgSpace ─┼────────────►
Bus Fabric │ │ │ 0
│ │ │
└──────────► MemSpace ─┼────────────►
IA: 0x8000_0000 │ │ 0x8000_0000
└────────────┘
bus@5f000000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x80000000 0x0 0x70000000 0x10000000>;
pcie@5f010000 {
compatible = "fsl,imx8q-pcie";
reg = <0x5f010000 0x10000>, <0x8ff00000 0x80000>;
reg-names = "dbi", "config";
...
};
};
Intermediate address (IA) here means the PCIe controller input address.
The pcie@5f010000 'reg[config]' address is the parent bus (PCIe controller
input) address of CfgSpace.
The ATU in MemSpace is not explicitly described via devicetree, so we
assume the offset from CPU address to intermediate MemSpace address is the
same as that for CfgSpace.
We could use bus@5f000000 'ranges' for the same purpose.
Set parent_bus_offset using dw_pcie_init_parent_bus_offset(). The
parent_bus_offset is not used yet, so no functional change intended.
Link: https://lore.kernel.org/r/20250315201548.858189-8-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dw_pcie_parent_bus_offset() looks up the parent bus address of a PCI
controller 'reg' property in devicetree. If implemented, .cpu_addr_fixup()
is a hard-coded way to get the parent bus address corresponding to a CPU
physical address.
Add debug code to compare the address from .cpu_addr_fixup() with the
address from devicetree. If they match, warn that .cpu_addr_fixup() is
redundant and should be removed; if they differ, warn that something is
wrong with the devicetree.
If .cpu_addr_fixup() is not implemented, the parent bus address should be
identical to the CPU physical address because we previously ignored the
parent bus address from devicetree. If the devicetree has a different
parent bus address, warn about it being broken.
[bhelgaas: split debug to separate patch for easier future revert, commit
log]
Link: https://lore.kernel.org/r/20250315201548.858189-7-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[bhelgaas: squash Ioana Ciornei <ioana.ciornei@nxp.com> fix for NULL
pointer deref when driver doesn't supply dw_pcie_ops, e.g., layerscape-pcie
https://lore.kernel.org/r/20250319134339.3114817-1-ioana.ciornei@nxp.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Return the offset from CPU physical address to the parent bus address of
the specified element of the devicetree 'reg' property.
[bhelgaas: cpu_phy_addr -> cpu_phys_addr, return offset, split
.cpu_addr_fixup() checking and debug to separate patch]
Link: https://lore.kernel.org/r/20250315201548.858189-6-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Update the CPM5 check to include CPM5_HOST1 variant. Previously, only
CPM5 was considered when mapping the "cpm_csr" register.
With this change, CPM5_HOST1 is also supported, ensuring proper
resource mapping for this variant.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250317124136.1317723-1-thippeswamy.havalige@amd.com
Don't populate the const read-only arrays "data" and "regs" on the
stack at run time, instead make them static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
[kwilczynski: commit log, wrap overly long line to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250317143456.477901-1-colin.i.king@gmail.com
Add support for AMD MDB (Multimedia DMA Bridge) IP core as Root Port.
The Versal2 devices include MDB Module. The integrated block for MDB
along with the integrated bridge can function as PCIe Root Port
controller at Gen5 32-GT/s operation per lane.
Bridge supports error and INTx interrupts and are handled using platform
specific interrupt line in Versal2.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250228093351.923615-4-thippeswamy.havalige@amd.com
[bhelgaas: only present on ARM64-based SoCs; squash Kconfig dependency on
ARM64 from Geert Uytterhoeven <geert+renesas@glider.be>:
https://lore.kernel.org/r/eaef1dea7edcf146aa377d5e5c5c85a76ff56bae.1742306383.git.geert+renesas@glider.be]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log, code comments and error messages clean-up,
drop redundant "depends on PCI" from Kconfig, expose the error code
as part of error messages where appropriatie, change "depends on"
expression to match existing style from other drivers]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-3-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
The access to the PCI config space via pci_ops::read and pci_ops::write is
a low-level hardware access. The functions can be accessed with disabled
interrupts even on PREEMPT_RT. The pci_lock is a raw_spinlock_t for this
purpose.
A spinlock_t becomes a sleeping lock on PREEMPT_RT, so it cannot be
acquired with disabled interrupts. The vmd_dev::cfg_lock is accessed in
the same context as the pci_lock.
Make vmd_dev::cfg_lock a raw_spinlock_t type so it can be used with
interrupts disabled.
This was reported as:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
Call Trace:
rt_spin_lock+0x4e/0x130
vmd_pci_read+0x8d/0x100 [vmd]
pci_user_read_config_byte+0x6f/0xe0
pci_read_config+0xfe/0x290
sysfs_kf_bin_read+0x68/0x90
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Tested-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Acked-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
[bigeasy: reword commit message]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/r/20250218080830.ufw3IgyX@linutronix.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: add back report info from
https://lore.kernel.org/lkml/20241218115951.83062-1-ryotkkr98@gmail.com/]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move devm_pci_alloc_host_bridge() to the beginning of dw_pcie_host_init().
devm_pci_alloc_host_bridge() is generic code that doesn't depend on any DWC
resource, so moving it earlier keeps all the subsequent devicetree-related
code together.
[bhelgaas: reorder earlier in series]
Link: https://lore.kernel.org/r/20250315201548.858189-4-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename 'cpu_addr' to 'parent_bus_addr' in the DesignWare ATU configuration.
The ATU translates parent bus addresses to PCI addresses, which are often
the same as CPU addresses but can differ in systems where the bus fabric
translates addresses before passing them to the PCIe controller. This
renaming clarifies the purpose and avoids confusion.
Link: https://lore.kernel.org/r/20250315201548.858189-3-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The msg_res region translates writes into PCIe Message TLPs. Previously we
mapped this region using atu.cpu_addr, the input address programmed into
the ATU.
"cpu_addr" is a misnomer because when a bus fabric translates addresses
between the CPU and the ATU, the ATU input address is different from the
CPU address. A future patch will rename "cpu_addr" and correct the value
to be the ATU input address instead of the CPU physical address.
Map the msg_res region before writing to it using the msg_res resource
start, a CPU physical address.
Link: https://lore.kernel.org/r/20250315201548.858189-2-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use devm_clk_bulk_get_all() helper to simplify clock handle code.
No functional changes intended.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log, refactor to use dev_err_probe()]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250226025628.1681206-1-hongxing.zhu@nxp.com
Instead of testing the controller register address to distinguish
controller 1 from controller 0 on i.MX8MQ platforms, use the PCI domain
number, which comes from the devicetree 'linux,pci-domain' property.
All relevant devicetrees should already supply 'linux,pci-domain', which
was added by c0b70f05c8 ("arm64: dts: imx8mq: use_dt_domains for pci
node").
Instead of being set directly in imx_pcie_probe(), pci->dbi_base will be
set by the DWC core in dw_pcie_get_resources().
No functional changes intended.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250226024256.1678103-3-hongxing.zhu@nxp.com
When running the RK3588 in Endpoint mode, with an Intel host with IOMMU
enabled, the host side prints:
DMAR: VT-d detected Invalidation Time-out Error: SID 0
When running the RK3588 in Endpoint mode, with an AMD host with IOMMU
enabled, the host side prints:
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01a0]
Rockchip has confirmed that the ATS support for RK3588 only works when
running the PCIe controller in Root Complex (RC) mode, see:
https://lore.kernel.org/linux-pci/93cdce39-1ae6-4939-a3fc-db10be7564e5@rock-chips.com
Usually, to handle these issues, we add a quirk for the PCI vendor and
device ID in drivers/pci/quirks.c with quirk_no_ats(). That is because
we cannot usually modify the capabilities on the EP side. In this case,
we can modify the capabilities on the EP side.
Thus, hide the broken ATS capability on RK3588 when running in EP mode.
That way, we don't need any quirk on the host side, and we see no errors
on the host side, and we can run pci_endpoint_test successfully, with
the IOMMU enabled on the host side.
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: commit log, tidy up code comments and error message]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250310094826.842681-6-cassel@kernel.org
Add dw_pcie_ep_hide_ext_capability() which can be used by an endpoint
controller driver to hide a capability.
This can be useful to hide a capability that is buggy, such that the
host side does not try to enable the buggy capability.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250310094826.842681-5-cassel@kernel.org
If the bitmap or memory allocations fail, then dw_pcie_ep_init_registers()
will incorrectly return a success.
Return -ENOMEM instead.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/36dcb6fc-f292-4dd5-bd45-a8c6f9dc3df7@stanley.mountain
Convert the code to use the new guard(msi_descs_lock).
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250313130321.758905320@linutronix.de
The Versal Net ACAP (Adaptive Compute Acceleration Platform) devices
incorporate the Coherency and PCIe Gen5 Module, specifically the
Next-Generation Compact Module (CPM5NC).
The integrated CPM5NC block, along with the built-in bridge, can function
as a PCIe Root Port and supports the PCIe Gen5 protocol with data transfer
rates of up to 32 GT/s, and is capable of supporting up to a x16 lane-width
configuration.
Bridge errors are managed using a specific interrupt line designed for
CPM5N. The INTx interrupt support is not available.
Currently in this commit platform specific bridge errors support is not
added.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: commit log, squashed patch to fix an if-statement condition
to ensure that xilinx_cpm_pcie_init_port() does not run on the CPM5NC_HOST
variant from https://lore.kernel.org/linux-pci/20250311072402.1049990-1-thippeswamy.havalige@amd.com]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250224155025.782179-4-thippeswamy.havalige@amd.com
The IRQ domain allocated for the PCIe controller is not freed if
resource_list_first_type() returns NULL, leading to a resource leak.
This fix ensures properly cleaning up the allocated IRQ domain in
the error path.
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: added missing Fixes: tag, refactored to use one of the goto labels]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250224155025.782179-2-thippeswamy.havalige@amd.com
Remove the superfluous function dw_pcie_ep_find_ext_capability(),
as it is virtually identical to dw_pcie_find_ext_capability().
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221202646.395252-3-cassel@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Looking at section "11.4.4.29 USP_PCIE_RESBAR Registers Summary" in the
Technical Reference Manual (TRM) for RK3588, we can see that none of the
BARs are Fixed BARs, but actually Resizable BARs.
I couldn't find any reference in the TRM for RK3568, but looking at the
downstream PCIe endpoint driver, both RK3568 and RK3588 are treated as
the same, so the BARs on RK3568 must also be Resizable BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-16-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The support for a specific iATU alignment was added in
commit 2a9a801620 ("PCI: endpoint: Add support to specify alignment for
buffers allocated to BARs").
This commit specifically mentions both that the alignment by each DWC
based EP driver should match CX_ATU_MIN_REGION_SIZE, and that AM65x
specifically has a 64 KB alignment.
This also matches the CX_ATU_MIN_REGION_SIZE value specified in the
section "12.2.2.4.7 PCIe Subsystem Address Translation" of the Technical
Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
This higher value, 1 MB, was obviously an ugly hack used to be able to
handle Resizable BARs which have a minimum size of 1 MB.
Now when we actually have support for Resizable BARs, let's configure the
iATU alignment requirement to the actual requirement.
(BARs described as Resizable will still get aligned to 1 MB.)
Cc: stable+noautosel@kernel.org # Depends on PCI endpoint Resizable BARs series
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-15-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Looking at section "12.2.2.4.15 PCIe Subsystem BAR Configuration" in the
following Technical Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
We can see that BAR2 and BAR5 are not Fixed BARs, but actually Resizable
BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-14-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The DWC databook specifies three different BARn_SIZING_SCHEME_N as:
- Fixed Mask (0)
- Programmable Mask (1)
- Resizable BAR (2)
Each of these sizing schemes have different instructions for how to
initialize the BAR.
The DWC driver currently does not support resizable BARs.
Instead, in order to somewhat support resizable BARs, the DWC EP driver
currently has an ugly hack that force sets a resizable BAR to 1 MB, if
such a BAR is detected.
Additionally, this hack only works if the DWC glue driver also has lied
in their EPC features, and claimed that the resizable BAR is a 1 MB fixed
size BAR.
This is unintuitive (as you somehow need to know that you need to lie in
your EPC features), but other than that it is overly restrictive, since a
resizable BAR is capable of supporting sizes different than 1 MB.
Add proper support for resizable BARs in the DWC EP driver.
Note that the pci_epc_set_bar() API takes a struct pci_epf_bar which tells
the EPC driver how it wants to configure the BAR.
struct pci_epf_bar only has a single size struct member.
This means that an EPC driver will only be able to set a single supported
size. This is perfectly fine, as we do not need the complexity of allowing
a host to change the size of the BAR. If someone ever wants to support
resizing a resizable BAR, the pci_epc_set_bar() API can be extended in the
future.
With these changes, we allow an EPF driver to configure the size of
Resizable BARs, rather than forcing them to a 1 MB size.
This means that an EPC driver does not need to lie in EPC features, and an
EPF driver will be able to set an arbitrary size (not be forced to a 1 MB
size), just like BAR_PROGRAMMABLE.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-13-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move dw_pcie_ep_find_ext_capability() so that it is located next to
dw_pcie_ep_find_capability().
Additionally, a follow-up commit requires this to be defined earlier
in order to avoid a forward declaration.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-12-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add PCIe Root Port controller support for the Agilex family of chips.
The Agilex PCIe Hard IP has three variants that are mostly software
compatible, except for a couple register offsets. The P-Tile variant
supports Gen3/Gen4 1x16. The F-Tile variant supports Gen3/Gen4 4x4,
4x8, and 4x16. The R-Tile variant improves on the F-Tile variant by
adding Gen5 support.
To simplify the implementation of pci_ops read/write functions,
ep_{read/write}_cfg() callbacks were added to struct altera_pci_ops
to easily distinguish between hardware variants.
Signed-off-by: D M, Sharath Kumar <sharath.kumar.d.m@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221170452.875419-3-matthew.gerlach@linux.intel.com
[kwilczynski: tidy code comments]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-7-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-6-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-5-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-4-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function.
Thus, convert the code to use dev_err_probe() to make code simpler.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240831040413.126417-3-zhangzekun11@huawei.com
[kwilczynski: commit log, return -ETIMEDOUT from hi3660_pcie_phy_start()
rather than -EINVAL for when the PIPE clock fails to become stable,
drop redundant dev->of_node NULL check]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move PCI_VENDOR_ID_ROCKCHIP from pci_endpoint_test.c to pci_ids.h and
reuse it in pcie-rockchip-host.c.
Link: https://lore.kernel.org/r/20250218092120.2322784-2-cassel@kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add the debugfs property to provide a view of the current link's LTSSM
status from the Root Port device.
Signed-off-by: Hans Zhang <18255117159@163.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Niklas Cassel <cassel@kernel.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250223141848.231232-1-18255117159@163.com
[kwilczynski: commit log, refactor dw_ltssm_sts_string() to avoid
compilation errors on platforms that do not set CONFIG_PCIE_DW_HOST]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Statistical Counter interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-6-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
squashed patch that checks if the event counter is supported from
https://lore.kernel.org/linux-pci/20250225171239.19574-3-manivannan.sadhasivam@linaro.org]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Error Injection interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-5-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
change debugfs property name from "duplicate_dllp" to "duplicate_tlp"]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Silicon Debug interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-4-shradha.t@samsung.com
[kwilczynski: commit log, tidy up Kconfig and drop "default y", tidy up
code comments, squashed patch that fixes a NULL pointer dereference when
debugfs is already unavailable during clean-up from
https://lore.kernel.org/linux-pci/20250225171239.19574-2-manivannan.sadhasivam@linaro.org,
refactor dwc_pcie_debugfs_init() to not return errors, squashed patch that
changes how lack of the RAS DES capability is handled from
https://lore.kernel.org/linux-pci/20250304151814.6xu7cbpwpqrvcad5@thinkpad]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Fix the following inconsistent indentation warning:
drivers/pci/controller/pcie-mediatek-gen3.c:922 mtk_pcie_parse_port() warn: inconsistent indenting
Found using Smatch. No functional changes intended.
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20250305070022.4668-1-hanchunchao@inspur.com
[kwilczynski: commit log, refactor if-statement around num_lanes to
make it more readable, wrap overly long lines to fit 80 colums]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-2-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Make the cast to the irq_hw_number_t type for the parameter passed to
irq_domain_set_info() function explicit.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-9-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The hardware has been updated with two changes to the MDIO packet
format.
The CMD field used to be 12 bits and now is only 1 bit. This change
is backwards compatible because the field's starting bit position is
unchanged, and the only commands we've used have values 0 and 1.
The PORT field's width has been changed from 4 bits to 5 bits. When
written, the new bit is not contiguous with the other four. However,
this change is backwards compatible because the driver never used
anything other than 0 for the port field's value.
Thus, update the existing code to handle new changes to the hardware
in a backwards-compatible manner.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-8-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The constants EXT_CFG_DATA and EXT_CFG_INDEX vary by SoC, where one of
the map_bus methods used these constants, and the other used a different
set of constants.
Thankfully, there was no problem because the SoCs that used the latter
map_bus method all had the same register constants.
Thus, remove redundant constants and adjust the code to use the correct
constants accordingly.
While at it, update the value of EXT_CFG_DATA to use the 4k-page based
configuration space access system, which is what the second map_bus
method was already using.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-7-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The platform supports enabling and disabling regulators only on
ports below the Root Complex.
Thus, we need to verify this both when adding and removing the bus,
otherwise regulators may be disabled prematurely when a bus further
down the topology is removed.
Fixes: 9e6be018b2 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-6-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
If the regulator_bulk_get() returns an error and no regulators
are created, we need to set their number to zero.
If we don't do this and the PCIe link up fails, a call to the
regulator_bulk_free() will result in a kernel panic.
While at it, print the error value, as we cannot return an error
upwards as the kernel will WARN() on an error from add_bus().
Fixes: 9e6be018b2 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-5-james.quinlan@broadcom.com
[kwilczynski: commit log, use comma in the message to match style with
other similar messages]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When setting the LNKCAP and LNKCTL2 register fields, it was assumed
that the field started at the LSB of the register.
Although the masks do indeed start at the LSB, and this will probably
not change, it is prudent to use a method that makes no assumption
about the mask's placement in the register.
Thus, use the u{16,32}p_replace_bits() helpers since they are already
wildly used in this driver.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-4-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The driver has been mistakenly writing to a read-only (RO)
configuration space register (PCI_EXP_LNKCAP) to change the
PCIe link capability.
Although harmless in this case, the proper write destination
is an internal register that is reflected by PCI_EXP_LNKCAP.
Thus, fix the brcm_pcie_set_gen() function to correctly update
the link capability.
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-3-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When the user elects to limit the PCIe generation via the appropriate
devicetree property, apply the settings before the PCIe link up, not
after.
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-2-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add a bare minimum amount of changes in order to support PCIe Root
Complex hardware IP found on RPi5. The PCIe controller on BCM2712
is based on BCM7712 and as such it inherits register offsets, PERST#
assertion, bridge_reset ops, and inbound windows count.
Although, the implementation for BCM2712 needs a workaround related to
the control of the bridge_reset where turning off of the Root Port must
not shutdown the bridge_reset and this must be avoided. To implement
this workaround a quirks field is introduced in pcie_cfg_data struct.
The controller also needs adjustment of PHY PLL setup to use a 54MHz
input refclk. The default input reference clock for the PHY PLL is
100Mhz, except for some devices where it is 54Mhz like BCM2712C1 and
BCM2712D0.
To implement those adjustments introduce a new .post_setup op in
pcie_cfg_data and call it at the end of brcm_pcie_setup function.
The BCM2712 .post_setup callback implements the required MDIO writes
that switch the PLL refclk and also change PHY PM clock period.
Without this RPi5 PCIex1 is unable to enumerate endpoint devices on
the expansion connector.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-8-svarbanov@suse.de
[commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Per the Cadence's "PCIe Controller IP for AX14" user guide, Version
1.04, Section 9.1.7.1, "AXI Subordinate to PCIe Address Translation
Registers", Table 9.4, the bit 16 of the AXI Subordinate Address
(axi_s_awaddr) when set corresponds to MSG with data, and when not set,
to MSG without data.
However, the driver is currently doing the opposite and due to this,
the INTx is never received on the host.
So, fix the driver to reflect the documentation and also make INTx work.
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Hans Zhang <hans.zhang@cixtech.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214165724.184599-1-18255117159@163.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The new dw_pcie_find_vsec_capability() helper will be used within
different DWC APIs to find the VSEC capabilities like PTM, RAS, etc.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-3-shradha.t@samsung.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Configure PBus base address and address mask to allow the hw
to detect if a given address is accessible on PCIe controller.
Fixes: f6ab898356 ("PCI: mediatek-gen3: Add Airoha EN7581 support")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20250225-en7581-pcie-pbus-csr-v4-2-24324382424a@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The BCM2712 memory map can support up to 64GB of system memory, thus
expand the inbound window size in calculation helper function.
The change is safe for the currently supported SoCs that have smaller
inbound window sizes.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-7-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Instead of copying fields from the pcie_cfg_data structure to
brcm_pcie, reference it directly.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelil <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-6-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Then the brcmstb PCIe driver and MIP MSI-X interrupt controller
drivers are built as modules there could be a race in probing.
To avoid this, add a softdep to MIP driver to guarantee that
MIP driver will be load first.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-5-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Calling cpumask_next_wrap_old() with starting CPU == nr_cpu_ids
is effectively the same as request to find first CPU, starting
from a given one and wrapping around if needed.
cpumask_next_wrap() is a proper replacement for that.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
The next patch aligns implementation of cpumask_next_wrap() with the
find_next_bit_wrap(), and it changes function signature.
To make the transition smooth, this patch deprecates current
implementation by adding an _old suffix. The following patches switch
current users to the new implementation one by one.
No functional changes were intended.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Enable PCIe Endpoint mode support for the Qualcomm SAR2130P platform.
This is needed, as it is not possible to use a compatible fallback on
any other platform since SAR2130P uses slightly different set of clocks.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250221-sar2130p-pci-v3-6-61a0fdfb75b4@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580 ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
On all Qcom endpoint SoCs, BAR0/BAR2 are 64bit BARs by default and
software cannot change the type.
So, mark the those BARs as 64bit BARs and also mark the successive
BAR1/BAR3 as RESERVED BARs so that the EPF drivers cannot use them.
Cc: stable+noautosel@kernel.org # depends on patch introducing only_64bit flag
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241231130224.38206-3-manivannan.sadhasivam@linaro.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Remove a leftover assert for mac_reset line in mtk_pcie_en7581_power_up().
This is not harmful since EN7581 does not requires mac_reset and
mac_reset is not defined in EN7581 device tree.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250201-pcie-en7581-remove-mac_reset-v2-1-a06786cdc683@kernel.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The VF driver controls an endpoint attached to the PCI HyperV
controller. An invalidation sent by the PF driver in the host
would be delivered *to* the endpoint driver by the controller
driver.
Thus, correct the wording within the comment.
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20250207190716.89995-1-eahariha@linux.microsoft.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
-----BEGIN PGP SIGNATURE-----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=O62O
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Batch sizing of multiple BARs while memory decoding is disabled
instead of disabling/enabling decoding for each BAR individually;
this optimizes virtualized environments where toggling decoding
enable is expensive (Alex Williamson)
- Add host bridge .enable_device() and .disable_device() hooks for
bridges that need to configure things like Requester ID to StreamID
mapping when enabling devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and
.disable_device() hooks so drivers that use pci_host_common_probe()
instead of their own .probe() have a way to set the
.enable_device() callbacks (Marc Zyngier)
- Drop 'No bus range found' message so we don't complain when DTs
don't specify the default 'bus-range = <0x00 0xff>' (Bjorn Helgaas)
- Rename the drivers/pci/of_property.c struct of_pci_range to
of_pci_range_entry to avoid confusion with the global of_pci_range
in include/linux/of_address.h (Bjorn Helgaas)
Driver binding:
- Update resource request API documentation to encourage callers to
supply a driver name when requesting resources (Philipp Stanner)
- Export pci_intx_unmanaged() and pcim_intx() (always managed) so
callers of pci_intx() (which is sometimes managed) can explicitly
choose the one they need (Philipp Stanner)
- Convert drivers from pci_intx() to always-managed pcim_intx() or
never-managed pci_intx_unmanaged(): amd_sfh, ata (ahci, ata_piix,
pata_rdc, sata_sil24, sata_sis, sata_uli, sata_vsc), bnx2x, bna,
ntb, qtnfmac, rtsx, tifm_7xx1, vfio, xen-pciback (Philipp Stanner)
- Remove pci_intx_unmanaged() since pci_intx() is now always
unmanaged and pcim_intx() is always managed (Philipp Stanner)
Error handling:
- Unexport pcie_read_tlp_log() to encourage drivers to use PCI core
logging rather than building their own (Ilpo Järvinen)
- Move TLP Log handling to its own file (Ilpo Järvinen)
- Store number of supported End-End TLP Prefixes always so we can
read the correct number of DWORDs from the TLP Prefix Log (Ilpo
Järvinen)
- Read TLP Prefixes in addition to the Header Log in
pcie_read_tlp_log() (Ilpo Järvinen)
- Add pcie_print_tlp_log() to consolidate printing of TLP Header and
Prefix Log (Ilpo Järvinen)
- Quirk the Intel Raptor Lake-P PIO log size to accommodate vendor
BIOSes that don't configure it correctly (Takashi Iwai)
ASPM:
- Save parent L1 PM Substates config so when we restore it along with
an endpoint's config, the parent info isn't junk (Jian-Hong Pan)
Power management:
- Avoid D3 for Root Ports on TUXEDO Sirius Gen1 with old BIOS because
the system can't wake up from suspend (Werner Sembach)
Endpoint framework:
- Destroy the EPC device in devm_pci_epc_destroy(), which previously
didn't call devres_release() (Zijun Hu)
- Finish virtual EP removal in pci_epf_remove_vepf(), which
previously caused a subsequent pci_epf_add_vepf() to fail with
-EBUSY (Zijun Hu)
- Write BAR_MASK before iATU registers in pci_epc_set_bar() so we
don't depend on the BAR_MASK reset value being larger than the
requested BAR size (Niklas Cassel)
- Prevent changing BAR size/flags in pci_epc_set_bar() to prevent
reads from bypassing the iATU if we reduced the BAR size (Niklas
Cassel)
- Verify address alignment when programming iATU so we don't attempt
to write bits that are read-only because of the BAR size, which
could lead to directing accesses to the wrong address (Niklas
Cassel)
- Implement artpec6 pci_epc_features so we can rely on all drivers
supporting it so we can use it in EPC core code (Niklas Cassel)
- Check for BARs of fixed size to prevent endpoint drivers from
trying to change their size (Niklas Cassel)
- Verify that requested BAR size is a power of two when endpoint
driver sets the BAR (Niklas Cassel)
Endpoint framework tests:
- Clear pci-epf-test dma_chan_rx, not dma_chan_tx, after freeing
dma_chan_rx (Mohamed Khalfella)
- Correct the DMA MEMCPY test so it doesn't fail if the Endpoint
supports both DMA_PRIVATE and DMA_MEMCPY (Manivannan Sadhasivam)
- Add pci-epf-test and pci_endpoint_test support for capabilities
(Niklas Cassel)
- Add Endpoint test for consecutive BARs (Niklas Cassel)
- Remove redundant comparison from Endpoint BAR test because a > 1MB
BAR can always be exactly covered by iterating with a 1MB buffer
(Hans Zhang)
- Move and convert PCI Endpoint tests from tools/pci to Kselftests
(Manivannan Sadhasivam)
Apple PCIe controller driver:
- Convert StreamID mapping configuration from a bus notifier to the
.enable_device() and .disable_device() callbacks (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Add Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank
Li)
- Add DT binding for optional i.MX95 Refclk and driver support to
enable it if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint
mode (Frank Li)
- Rely on dbi2 and iATU base addresses from DT via
dw_pcie_get_resources() instead of hardcoding them (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX,
IMX7D, IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since
imx7d_pcie_enable_ref_clk() does the same thing (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead
of syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
Marvell MVEBU PCIe controller driver:
- Add MODULE_DEVICE_TABLE() to enable module autoloading (Liao Chen)
MediaTek PCIe Gen3 controller driver:
- Use clk_bulk_prepare_enable() instead of separate
clk_bulk_prepare() and clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the
*_power_up() callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before
PHY reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo
Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is
a non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and
suspend/resume to avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
Microchip PolarFlare PCIe controller driver:
- Set up the inbound address translation based on whether the
platform allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default
and must specify 'dma-noncoherent' if needed (Conor Dooley)
Mobiveil PCIe controller driver:
- Convert mobiveil-pcie.txt to YAML and update 'interrupt-names'
and 'reg-names' (Frank Li)
Qualcomm PCIe controller driver:
- Add DT SM8550 and SM8650 optional 'global' interrupt for link
events (Neil Armstrong)
- Add DT 'compatible' strings for IPQ5424 PCIe controller (Manikanta
Mylavarapu)
- If 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
Renesas R-Car PCIe controller driver:
- Avoid passing stack buffer as resource name (King Dix)
Rockchip PCIe controller driver:
- Simplify clock and reset handling by using bulk interfaces (Anand
Moon)
- Pass typed rockchip_pcie (not void) pointer to
rockchip_pcie_disable_clocks() (Anand Moon)
- Return -ENOMEM, not success, when pci_epc_mem_alloc_addr() fails
(Dan Carpenter)
Rockchip DesignWare PCIe controller driver:
- Use dll_link_up IRQ to detect Link Up and enumerate devices so
users don't have to manually rescan (Niklas Cassel)
- Tell DWC core not to wait for link up since the 'sys' interrupt is
required and detects Link Up events (Niklas Cassel)
Synopsys DesignWare PCIe controller driver:
- Don't wait for link up in DWC core if driver can detect Link Up
event (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya
chundru)
- Always stop link in dw_pcie_suspend_noirq(), which is required at
least for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending
PME_TURN_OFF message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program
an internal Address Translation Unit (iATU) (Frank Li)
TI DRA7xx PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Xilinx Versal CPM5
(Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Add Microchip PCI100X device IDs (Rakesh Babu Saladi)
Miscellaneous:
- Move reset related sysfs code from pci.c to pci-sysfs.c where other
similar code lives (Ilpo Järvinen)
- Simplify reset_method_store() memory management by using __free()
instead of explicit kfree() cleanup (Ilpo Järvinen)
- Constify struct bin_attribute for sysfs, VPD, P2PDMA, and the IBM
ACPI hotplug driver (Thomas Weißschuh)
- Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT (Dongdong
Zhang)
- Correct documentation of the 'config_acs=' kernel parameter
(Akihiko Odaki)"
* tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (111 commits)
PCI: Batch BAR sizing operations
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
Documentation: Fix pci=config_acs= example
PCI: Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT
PCI: Don't include 'pm_wakeup.h' directly
selftests: pci_endpoint: Migrate to Kselftest framework
selftests: Move PCI Endpoint tests from tools/pci to Kselftests
misc: pci_endpoint_test: Fix IOCTL return value
dt-bindings: PCI: qcom: Document the IPQ5424 PCIe controller
dt-bindings: PCI: qcom,pcie-sm8550: Document 'global' interrupt
dt-bindings: PCI: mobiveil: Convert mobiveil-pcie.txt to YAML
PCI: switchtec: Add Microchip PCI100X device IDs
misc: pci_endpoint_test: Remove redundant 'remainder' test
misc: pci_endpoint_test: Add consecutive BAR test
misc: pci_endpoint_test: Add support for capabilities
PCI: endpoint: pci-epf-test: Add support for capabilities
PCI: endpoint: pci-epf-test: Fix check for DMA MEMCPY test
PCI: endpoint: pci-epf-test: Set dma_chan_rx pointer to NULL on error
PCI: dwc: Simplify config resource lookup
...
- Add DT binding and driver support for Xilinx Versal CPM5 (Thippeswamy
Havalige)
* pci/controller/xilinx-cpm:
PCI: xilinx-cpm: Add support for Versal CPM5 Root Port Controller 1
dt-bindings: PCI: xilinx-cpm: Add compatible string for CPM5 host1
- Set up the inbound address translation based on whether the platform
allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default and
must specify 'dma-noncoherent' if needed (Conor Dooley)
* pci/controller/microchip:
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
- Use clk_bulk_prepare_enable() instead of separate clk_bulk_prepare() and
clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the *_power_up()
callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before PHY
reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is a
non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and suspend/resume to
avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
* pci/controller/mediatek:
PCI: mediatek-gen3: Enable async probe by default
PCI: mediatek-gen3: Avoid PCIe resetting via PERST# for Airoha EN7581 SoC
PCI: mediatek-gen3: Rely on msleep() in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset delay in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Add comment about initialization order in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset/assert callbacks in .power_up()
PCI: mediatek-gen3: Rely on clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up()
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
* pci/controller/layerscape:
PCI: layerscape: Use syscon_regmap_lookup_by_phandle_args
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank Li)
- Add DT binding for optional i.MX95 Refclk and driver support to enable it
if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint mode
(Frank Li)
- Rely on dbi2 and iATU base addresses from DT via dw_pcie_get_resources()
instead of hardcoding them in imx6 (Richard Zhu)
- Skip controller_id computation for i.MX7D since it only has one
controller (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX, IMX7D,
IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since imx7d_pcie_enable_ref_clk()
does the same thing (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Clean up comments and whitespace
PCI: imx6: Remove surplus imx7d_pcie_init_phy() function
PCI: imx6: Add missing reference clock disable logic
PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()
PCI: imx6: Skip controller_id generation logic for i.MX7D
PCI: imx6: Fetch dbi2 and iATU base addesses from DT
PCI: imx6: Configure PHY based on Root Complex or Endpoint mode
PCI: imx6: Add Refclk for i.MX95 PCIe
dt-bindings: PCI: fsl,imx6q-pcie: Add Refclk for i.MX95 RC
PCI: imx6: Add i.MX8Q PCIe Endpoint (EP) support
dt-bindings: PCI: fsl,imx6q-pcie-ep: Add compatible string fsl,imx8q-pcie-ep
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
- Fix potential string truncation in dw_pcie_edma_irq_verify() (Niklas
Cassel)
- Don't wait for link up in DWC core if driver can detect Link Up event
(Krishna chaitanya chundru)
- If qcom 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya chundru)
- Use dw-rockchip dll_link_up IRQ to detect Link Up and enumerate devices
so users don't have to manually rescan (Niklas Cassel)
- In dw-rockchip, the 'sys' interrupt is required and detects Link Up
events, so tell DWC core not to wait for link up (Niklas Cassel)
- Always stop link in dw_pcie_suspend_noirq(), which is required at least
for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending PME_TURN_OFF
message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add stubs for dw_pcie_suspend_noirq() dw_pcie_resume_noirq() when
CONFIG_PCIE_DW_HOST is not defined so drivers don't need #ifdefs (Bjorn
Helgaas)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add imx6 suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program an
internal Address Translation Unit (iATU) (Frank Li)
* pci/controller/dwc:
PCI: dwc: Simplify config resource lookup
of: address: Add parent_bus_addr to struct of_pci_range
PCI: imx6: Add i.MX8MQ, i.MX8Q and i.MX95 PM support
PCI: imx6: Use DWC common suspend resume method
PCI: dwc: Add dw_pcie_suspend_noirq(), dw_pcie_resume_noirq() stubs for !CONFIG_PCIE_DW_HOST
PCI: dwc: Remove LTSSM state test in dw_pcie_suspend_noirq()
PCI: dwc: Always stop link in the dw_pcie_suspend_noirq
PCI: dw-rockchip: Don't wait for link since we can detect Link Up
PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ
PCI: qcom: Update ICC and OPP values after Link Up event
PCI: qcom: Don't wait for link if we can detect Link Up
PCI: dwc: Don't wait for link up if driver can detect Link Up event
PCI: dwc: Fix potential truncation in dw_pcie_edma_irq_verify()
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
* pci/controller/dra7xx:
PCI: dra7xx: Use syscon_regmap_lookup_by_phandle_args
- Add host bridge .enable_device() and .disable_device() hooks for bridges
that need to configure things like Requester ID to StreamID mapping when
enabling devices (Frank Li)
- Add imx6 Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and .disable_device()
hooks so drivers that use pci_host_common_probe() instead of their own
.probe() have a way to set the .enable_device() callbacks (Marc Zyngier)
- Convert pcie-apple StreamID mapping configuration from a bus notifier to
the .enable_device() and .disable_device() callbacks (Marc Zyngier)
* pci/controller/iommu-map:
PCI: apple: Convert to {en,dis}able_device() callbacks
PCI: host-generic: Allow {en,dis}able_device() to be provided via pci_ecam_ops
PCI: imx6: Add IOMMU and ITS MSI support for i.MX95
PCI: Add enable_device() and disable_device() callbacks for bridges
drivers, per usual, and then a handful of drivers for other SoCs. Then the
usual pile of cleanups is fairly small data fixes or converting DT bindings to
YAML so they can be validated. No changes to the core framework besides an OF
node refcount bump that never got decremented.
New Drivers:
- 5L35023 variant of Versa 3 clock generator
- Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750 global,
tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh and MSM8937 and
MSM8940 RPM.
- Qualcomm Pongo and Taycan Alpha PLLs
- Qualcomm IPQ5424 NoC-related interconnect clks
- Renesas RZ/G3E (R9A09G047) SoC clk driver
- SAMA7D65 SoC clk driver
- Samsung Exynos990 SoC clk driver
-----BEGIN PGP SIGNATURE-----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=wK9g
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"A pretty quiet cycle this time around. We have a bunch of new Qualcomm
clk drivers, per usual, and then a handful of drivers for other SoCs.
Then the usual pile of cleanups is fairly small data fixes or
converting DT bindings to YAML so they can be validated.
No changes to the core framework besides an OF node refcount bump that
never got decremented.
New Drivers:
- 5L35023 variant of Versa 3 clock generator
- Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750
global, tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh
and MSM8937 and MSM8940 RPM.
- Qualcomm Pongo and Taycan Alpha PLLs
- Qualcomm IPQ5424 NoC-related interconnect clks
- Renesas RZ/G3E (R9A09G047) SoC clk driver
- SAMA7D65 SoC clk driver
- Samsung Exynos990 SoC clk driver"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (159 commits)
clk: analogbits: Fix incorrect calculation of vco rate delta
clk: bcm: rpi: Add disp clock
clk: bcm: rpi: Create helper to retrieve private data
clk: bcm: rpi: Enable minimize for all firmware clocks
clk: bcm: rpi: Allow cpufreq driver to also adjust gpu clocks
clk: bcm: rpi: Add ISP to exported clocks
clk: stm32f4: support spread spectrum clock generation
clk: stm32f4: use FIELD helpers to access the PLLCFGR fields
dt-bindings: clock: st,stm32-rcc: support spread spectrum clocking
dt-bindings: clock: convert stm32 rcc bindings to json-schema
clk: Use str_enable_disable-like helpers
clk: clk-loongson2: Fix the number count of clk provider
clk: clk-loongson2: Switch to use devm_clk_hw_register_fixed_rate_parent_data()
clk: starfive: Make _clk_get become a common helper function
clk: en7523: Add clock for eMMC for EN7581
dt-bindings: clock: add ID for eMMC for EN7581
dt-bindings: clock: drop NUM_CLOCKS define for EN7581
clk: en7523: Rework clock handling for different clock numbers
clk: thead: Fix cpu2vp_clk for TH1520 AP_SUBSYS clocks
clk: thead: Add CLK_IGNORE_UNUSED to fix TH1520 boot
...
On Microchip PolarFire SoC the PCIe Root Port can be behind one of three
general purpose Fabric Interface Controller (FIC) buses that encapsulates
an AXI-S bus. Depending on which FIC(s) the Root Port is connected through
to CPU space, and what address translation is done by that FIC, the Root
Port driver's inbound address translation may vary.
For all current supported designs and all future expected designs, inbound
address translation done by a FIC on PolarFire SoC varies depending on
whether PolarFire SoC is operating in coherent DMA mode or noncoherent DMA
mode.
The setup of the outbound address translation tables in the Root Port
driver only needs to handle these two cases.
Setup the inbound address translation tables to one of two address
translations, depending on whether the Root Port is being used with
coherent DMA or noncoherent DMA.
Link: https://lore.kernel.org/r/20241011140043.1250030-3-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[bhelgaas: adapt for ac7f53b7e7 ("PCI: microchip: Add support for using
either Root Port 1 or 2")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
If platform_get_resource_byname("config") fails, return error immediately
and unindent the normal path. No functional change intended.
Link: https://lore.kernel.org/r/20250117235119.712043-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Call common DWC suspend/resume function. Use DWC common iATU method to
send out PME_TURN_OFF message.
In old DWC implementations, PCIE_ATU_INHIBIT_PAYLOAD in iATU Ctrl2 register
is reserved, so the generic DWC implementation of sending the PME_Turn_Off
message using a dummy MMIO write cannot be used. Use the previous method to
kick off PME_TURN_OFF message for these platforms.
The System Reset Control (SRC) interface is used to toggle 'turnoff_reset'
to send PME_TURN_OFF and since the DWC implementation is used, it is not
needed now.
Replace the imx_pcie_stop_link() and imx_pcie_host_exit() by
dw_pcie_suspend_noirq() in imx_pcie_suspend_noirq().
Since dw_pcie_suspend_noirq() already does these, see below call stack:
dw_pcie_suspend_noirq()
dw_pcie_stop_link()
imx_pcie_stop_link()
pci->pp.ops->deinit()
imx_pcie_host_exit()
Replace the imx_pcie_host_init(), dw_pcie_setup_rc() and
imx_pcie_start_link() by dw_pcie_resume_noirq() in imx_pcie_resume_noirq().
Since dw_pcie_resume_noirq() already does these, see below call stack:
dw_pcie_resume_noirq()
pci->pp.ops->init()
imx_pcie_host_init()
dw_pcie_setup_rc()
dw_pcie_start_link()
imx_pcie_start_link(;
Link: https://lore.kernel.org/r/20241126075702.4099164-9-hongxing.zhu@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pcie-designware.h declared dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq() unconditionally, even though they were only
implemented when CONFIG_PCIE_DW_HOST was defined.
Add no-op stubs for them when CONFIG_PCIE_DW_HOST is not defined so
drivers that support both Root Complex and Endpoint modes don't need
Link: https://lore.kernel.org/r/20250117213810.GA656803@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's safe to send PME_TURN_OFF message regardless of whether the link is up
or down, so don't test the LTSSM state before sending the PME_TURN_OFF
message.
Only print an error message when the LTSSM is not in DETECT or POLL. There
shouldn't be an error when no Endpoint is connected at all.
Link: https://lore.kernel.org/r/20241210081557.163555-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
On the i.MX8QM, PCIe link can't be re-established again in
dw_pcie_resume_noirq(), if the LTSSM_EN bit is not cleared
properly in dw_pcie_suspend_noirq().
So, add dw_pcie_stop_link() to dw_pcie_suspend_noirq() to fix
this issue and to align the suspend/resume functions since there
is dw_pcie_start_link() in dw_pcie_resume_noirq() already.
Fixes: 4774faf854 ("PCI: dwc: Implement generic suspend/resume functionality")
Link: https://lore.kernel.org/r/20241210081557.163555-2-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Root Complex specific device tree binding for pcie-dw-rockchip has the
'sys' interrupt marked as required.
The driver requests the 'sys' IRQ unconditionally, and errors out if not
provided.
Thus, we can unconditionally set 'use_linkup_irq', so dw_pcie_host_init()
doesn't wait for the link to come up.
This will skip the wait for link up (since the bus will be enumerated once
the link up IRQ is triggered), which reduces the bootup time.
Link: https://lore.kernel.org/r/20250113-rockchip-no-wait-v1-1-25417f37b92f@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Most boards using the pcie-dw-rockchip PCIe controller lack standard
hotplug support.
Thus, when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. This can be avoided by using the
'dll_link_up' interrupt in the combined system interrupt 'sys'.
Once the 'dll_link_up' IRQ is received, the bus underneath the host bridge
is scanned to enumerate PCIe endpoint devices.
This implements the same functionality that was implemented in the DWC
based pcie-qcom driver in 4581403f67 ("PCI: qcom: Enumerate endpoints
based on Link up event in 'global_irq' interrupt").
The Root Complex specific device tree binding for pcie-dw-rockchip already
has the 'sys' interrupt marked as required, so there is no need to update
the device tree binding. This also means that we can request the 'sys' IRQ
unconditionally.
Link: https://lore.kernel.org/r/20241127145041.3531400-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, squash Pei Xiao's redundant dev_err() fix from
https://lore.kernel.org/r/327718207d3cd72847c079ff9d56eb246744c182.1736126067.git.xiaopei01@kylinos.cn,
squash Niklas's #define change from https://lore.kernel.org/r/20250103095812.2408364-2-cassel@kernel.org]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in
'global_irq' interrupt") added the Link Up-based enumeration support, but
did not update the ICC/OPP vote once link is up. Before that, the update
happened during probe and the endpoints may or may not be enumerated at
that time, so the ICC/OPP vote was not guaranteed to be accurate.
With Link Up-based enumeration support, the driver can request the accurate
vote based on the PCIe link.
Call qcom_pcie_icc_opp_update() in qcom_pcie_global_irq_thread() after
enumerating the endpoints.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-3-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If we have a 'global' IRQ for Link Up events, we need not wait for the
link to be up during PCI initialization, which reduces startup time.
Check for 'global' IRQ, and if present, set 'use_linkup_irq',
so dw_pcie_host_init() doesn't wait for the link to come up.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-2-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If the driver can detect the Link Up event and enumerate downstream devices
at that time, we need not wait here.
Skip waiting for link to come up if the driver supports 'use_linkup_irq'.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-1-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comment, update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Increase the size of the string buffer to avoid potential truncation in
dw_pcie_edma_irq_verify().
This fixes the following build warning when compiling with W=1:
drivers/pci/controller/dwc/pcie-designware.c: In function ‘dw_pcie_edma_detect’:
drivers/pci/controller/dwc/pcie-designware.c:989:50: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 3 [-Wformat-truncation=]
989 | snprintf(name, sizeof(name), "dma%d", pci->edma.nr_irqs);
| ^~
Link: https://lore.kernel.org/r/20250104002119.2681246-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-1-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-2-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
This function essentially duplicates imx7d_pcie_enable_ref_clk(). So remove
it.
Link: https://lore.kernel.org/r/20241126075702.4099164-8-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Ensure the *_enable_ref_clk() function is symmetric by addressing missing
disable parts on some platforms.
Fixes: d0a75c791f ("PCI: imx6: Factor out ref clock disable to match enable")
Link: https://lore.kernel.org/r/20241126075702.4099164-7-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Since the apps_reset is asserted in imx_pcie_assert_core_reset(), it should
be deasserted in imx_pcie_deassert_core_reset().
Fixes: 9b3fe6796d ("PCI: imx6: Add code to support i.MX7D")
Link: https://lore.kernel.org/r/20241126075702.4099164-6-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
The i.MX7D only has one PCIe controller, so controller_id should always be
0. The previous code is incorrect although yielding the correct result.
Fix by removing "IMX7D" from the switch case branch.
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Link: https://lore.kernel.org/r/20241126075702.4099164-5-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Since dw_pcie_get_resources() gets the dbi2 and iATU base addresses from
DT, remove the code from the imx6 driver that does the same.
Upstream DTSes have not enabled Endpoint function. So nothing is broken for
old upstream DTBs.
Link: https://lore.kernel.org/r/20241126075702.4099164-4-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Pass PHY_MODE_PCIE_EP if the PCI controller operates in Endpoint (EP) mode,
and fix the Root Complex (RC) mode being hardcoded using a drvdata mode
check.
Fixes: 8026f2d8e8 ("PCI: imx6: Call common PHY API to set mode, speed, and submode")
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-6-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Add "ref" clock to enable Refclk. To avoid breaking DT backwards
compatibility, the i.MX95 "ref" clock is optional. Use
devm_clk_get_optional() to fetch i.MX95 PCIe optional clocks in driver.
If using external clock, "ref" clock should point to external reference.
If using internal clock, CREF_EN in LAST_TO_REG controls reference output,
implemented in drivers/clk/imx/clk-imx95-blk-ctl.c.
Link: https://lore.kernel.org/r/20241126075702.4099164-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Add support for the i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe
Endpoint (EP). On the i.MX8Q platforms, the PCI bus addresses differ
from the CPU addresses. However, the DesignWare (DWC) driver already
handles this in the common code.
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-7-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Now that the core host-bridge infrastructure is able to give us a callback
on each device being added or removed, convert the bus-notifier hack to it.
Link: https://lore.kernel.org/r/20241204150145.800408-3-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In order to let host controller drivers using the host-generic
infrastructure use the {en,dis}able_device() callbacks that can be used to
configure sideband RID mapping hardware, provide these two callbacks as
part of the pci_ecam_ops structure.
Link: https://lore.kernel.org/r/20241204150145.800408-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
For the i.MX95, the configuration of a LUT is necessary to convert PCIe
Requester IDs (RIDs) to StreamIDs, which are used by both IOMMU and ITS.
This involves checking msi-map and iommu-map device tree properties to
ensure consistent mapping of Requester IDs to the same StreamIDs.
Subsequently, LUT-related registers are configured. If a msi-map isn't
detected, the platform relies on DWC built-in controller for MSIs that
do not need StreamIDs.
Implement PCI bus callback function to handle enable_device() and
disable_device() operations, setting up the LUT whenever a new PCI
device is enabled.
Known limitations:
- If iommu-map exists in the device tree but the IOMMU controller is
disabled, StreamIDs are programmed into the LUT. However, if a RID
is out of range of the iommu-map, enabling the PCI device would
result in a failure, although the PCI device can work without the
IOMMU.
- If msi-map exists in the device tree but the MSI controller is
disabled, MSIs will not work. The DWC driver skips initializing the
built-in MSI controller, falling back to legacy PCI INTx only.
Link: https://lore.kernel.org/r/20250114-imx95_lut-v9-2-39f58dbed03a@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: fix uninitialized "sid" in imx_pcie_enable_device()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Instead of marking individual interrupts as safe to be migrated in
arbitrary contexts, mark the interrupt chips, which require the interrupt
to be moved in actual interrupt context, with the new IRQCHIP_MOVE_DEFERRED
flag. This makes more sense because this is a per interrupt chip property
and not restricted to individual interrupts.
That flips the logic from the historical opt-out to a opt-in model. This is
simpler to handle for other architectures, which default to unrestricted
affinity setting. It also allows to cleanup the redundant core logic
significantly.
All interrupt chips, which belong to a top-level domain sitting directly on
top of the x86 vector domain are marked accordingly, unless the related
setup code marks the interrupts with IRQ_MOVE_PCNTXT, i.e. XEN.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/all/20241210103335.563277044@linutronix.de
Refactor rockchip_pcie_disable_clocks() to accept a struct rockchip_pcie
pointer instead of a void pointer thus improving type safety and code
readability by explicitly specifying the expected data type.
Link: https://lore.kernel.org/r/20241202151150.7393-4-linux.amoon@gmail.com
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the driver acquires and asserts/deasserts the resets
individually thereby making the driver complex to read.
This can be simplified by using the reset_control_bulk() APIs.
Use devm_reset_control_bulk_get_exclusive() API to acquire all the resets
and use reset_control_bulk_{assert/deassert}() APIs to assert/deassert them
in bulk.
Following the recommendations in 'Rockchip RK3399 TRM v1.3 Part2':
1. Split the reset controls into two groups as per section '17.5.8.1.1
PCIe as Root Complex'.
2. Deassert the 'Pipe, MGMT Sticky, MGMT, Core' resets in groups as per
section '17.5.8.1.1 PCIe as Root Complex'. This is accomplished using
the reset_control_bulk APIs.
Link: https://lore.kernel.org/r/20241202151150.7393-3-linux.amoon@gmail.com
Co-developed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: squash error handling fix from https://lore.kernel.org/r/7da6ac56-af55-4436-9597-6af24df8122c@stanley.mountain]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Link: https://lore.kernel.org/r/20240903132311.961646-1-liaochen4@huawei.com
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Currently, the driver acquires clocks and prepare/enable/disable/unprepare
the clocks individually thereby making the driver complex to read.
The driver can be simplified by using the clk_bulk*() APIs.
Use:
- devm_clk_bulk_get_all() API to acquire all the clocks
- clk_bulk_prepare_enable() to prepare/enable clocks
- clk_bulk_disable_unprepare() APIs to disable/unprepare them in bulk
Link: https://lore.kernel.org/r/20241202151150.7393-2-linux.amoon@gmail.com
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
[bhelgaas: squash error handling fix from https://lore.kernel.org/r/20250106153041.55267-1-linux.amoon@gmail.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When compiling the Rockchip endpoint driver with -W=1, the following
warnings can be seen in the output:
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_irq' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_asserted' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_up' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_training' not described in 'rockchip_pcie_ep'
Fix these warnings by adding the missing field descriptions in
struct rockchip_pcie_ep kernel-doc comment.
Fixes: a7137cbf6b ("PCI: rockchip-ep: Handle PERST# signal in EP mode")
Fixes: bd6e61df4b ("PCI: rockchip-ep: Improve link training")
Link: https://lore.kernel.org/r/20241216133404.540736-1-dlemoal@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region()
macro to request a needed resource. A string variable that lives on the
stack is then used to store a dynamically computed resource name, which
is then passed on as one of the macro arguments. This can lead to
undefined behavior.
Depending on the current contents of the memory, the manifestations of
errors may vary. One possible output may be as follows:
$ cat /proc/iomem
30000000-37ffffff :
38000000-3fffffff :
Sometimes, garbage may appear after the colon.
In very rare cases, if no NULL-terminator is found in memory, the system
might crash because the string iterator will overrun which can lead to
access of unmapped memory above the stack.
Thus, fix this by replacing outbound_name with the name of the previously
requested resource. With the changes applied, the output will be as
follows:
$ cat /proc/iomem
30000000-37ffffff : memory2
38000000-3fffffff : memory3
Fixes: 2a6d0d63d9 ("PCI: rcar: Add endpoint mode support")
Link: https://lore.kernel.org/r/tencent_DBDCC19D60F361119E76919ADAB25EC13C06@qq.com
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: King Dix <kingdix10@qq.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mediatek-gen3 driver can run its probe routine fairly slow on some
hardware, which adds to the total time it takes for the system start up.
Thus, turn on async mode for the probe to avoid blocking the rest of the
system.
Link: https://lore.kernel.org/r/20241220145205.1.Ibf2563896c3b1fc133bb46d3fc96ad0041763922@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PERST# signal causing
occasional PCIe link down issues. In order to overcome the problem,
PERST# signal is not asserted/released during device probe or
suspend/resume phase and the PCIe block is reset using
en7523_reset_assert() and en7581_pci_enable().
Introduce flags field in the mtk_gen3_pcie_pdata struct in order to
specify per-SoC capabilities.
Link: https://lore.kernel.org/r/20250109-pcie-en7581-rst-fix-v4-1-4a45c89fb143@kernel.org
Tested-by: Hui Ma <hui.ma@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Since mtk_pcie_en7581_power_up() runs in non-atomic context, rely on
msleep() routine instead of mdelay().
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-5-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PCIE_PE_RSTB signal
causing occasional PCIe link down issues. In order to overcome the
problem, PCIe block is reset using REG_PCI_CONTROL (0x88) and
REG_RESET_CONTROL (0x834) registers available in the clock module
running clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up().
In order to make the code more readable, move the wait for the time
needed to complete the PCIe reset from en7581_pci_enable() to
mtk_pcie_en7581_power_up().
Reduce reset timeout from 250ms to the standard PCIE_T_PVPERL_MS value
(100ms) since it has no impact on the driver behavior.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-4-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Add a comment in mtk_pcie_en7581_power_up() to clarify, unlike the other
MediaTek Gen3 controllers, the Airoha EN7581 requires PHY initialization
and power-on before PHY reset deassert.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-3-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
In order to make the code more readable, the reset_control_bulk_assert()
function for PHY reset lines is moved to make it pair with
reset_control_bulk_deassert() in mtk_pcie_power_up() and
mtk_pcie_en7581_power_up(). The same change is done for
reset_control_assert() used to assert MAC reset line.
Introduce PCIE_MTK_RESET_TIME_US macro for the time needed to
complete PCIe reset on MediaTek controller.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-2-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Replace clk_bulk_prepare() and clk_bulk_enable() with
clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up() routine.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-1-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The helper devm_clk_bulk_get_all_enable() missed to return the number of
clocks stored in the clk_bulk_data table referenced by the clks
argument and, therefore, will be dropped.
Use the newly introduced devm_clk_bulk_get_all_enabled() variant
instead, which is consistent with devm_clk_bulk_get_all() in terms of
the returned value:
> 0 if one or more clocks have been stored
= 0 if there are no clocks
< 0 if an error occurred
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20241217-clk_bulk_ena_fix-v5-2-aafbbb245155@collabora.com
Acked-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the Xilinx Versal CPM5 Root Port Controller 1. The key
difference between Controller 0 and Controller 1 lies in the
platform-specific error interrupt bits, which are located at different
register offsets.
To handle these differences, updated variant structure to hold the
following platform-specific details:
- Interrupt status register offset (ir_status)
- Interrupt enable register offset (ir_enable)
- Miscellaneous interrupt values (ir_misc_value)
The driver differentiates between Controller 0 and Controller 1 using the
compatible string in the device tree. This ensures that the appropriate
register offsets are used for each controller, allowing for correct
handling of platform-specific interrupts and initialization.
Link: https://lore.kernel.org/r/20240922061318.2653503-3-thippesw@amd.com
Signed-off-by: Thippeswamy Havalige <thippesw@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
All non-DWC EPC drivers implement (struct pci_epc *)->ops->get_features().
All DWC EPC drivers implement (struct dw_pcie_ep *)->ops->get_features(),
except for pcie-artpec6.c.
epc_features has been required in pci-epf-test.c since commit 6613bc2301
("PCI: endpoint: Fix NULL pointer dereference for ->get_features()").
A follow-up commit will make further use of epc_features in EPC core code.
Implement epc_features in the only EPC driver where it is currently not
implemented.
Link: https://lore.kernel.org/r/20241213143301.4158431-12-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
dw_pcie_prog_ep_inbound_atu() is used to program an inbound iATU in
"BAR Match Mode".
A memory address returned by e.g. kmalloc() is guaranteed to have natural
alignment (aligned to the size of the allocation). It is however not
guaranteed that pci_epc_set_bar() (and thus dw_pcie_prog_ep_inbound_atu())
is supplied an address that has natural alignment. (An EPF driver can send
in an arbitrary physical address to pci_epc_set_bar().)
The DWC Databook description for the LWR_TARGET_RW and LWR_TARGET_HW fields
in the IATU_LWR_TARGET_ADDR_OFF_INBOUND_i registers state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
Add a check to ensure that the physical address programmed in the iATU is
aligned to the size of the BAR (BAR_MASK+1), as without this, we can get
hard to debug errors, as we could write to bits that are read-only (without
getting a write error), which could cause the iATU to end up redirecting to
a physical address that is different from the address that we intended.
Link: https://lore.kernel.org/r/20241213143301.4158431-11-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In commit 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
* pci/controller/vmd:
PCI: vmd: Add DID 8086:B06F and 8086:B60B for Intel client SKUs
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
* pci/controller/tegra194:
PCI: tegra194: Move controller cleanups to pex_ep_event_pex_rst_deassert()
- Fix address translation unit programming (Damien Le Moal)
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint .align
value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead of
searching for it, and verify that the address was mapped (Damien Le Moal)
- When mapping an endpoint window, verify that the address hasn't been
mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which fixes
intermittent page faults in memcpy_toio() and memcpy_fromio() (Damien Le
Moal)
- Rename rockchip_pcie_parse_ep_dt() to rockchip_pcie_ep_get_resources()
for consistency with similar DT interfaces (Damien Le Moal)
- Factor out memory allocations to tidy rockchip_pcie_ep_probe() (Damien Le
Moal)
- Factor out MSI-X quirk to tidy rockchip_pcie_ep_probe() (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and only in
the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and controller
configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it (Damien Le
Moal)
- Add a handler for PERST# signal so we can detect host resets and start
link training when exiting reset (Damien Le Moal)
* pci/controller/rockchip:
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
- Enable MSI interrupts if 'global' IRQ is supported, since a previous
commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP v5.80a
and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the qcom,pcie-sm8450.yaml
DT binding to qcom,pcie-common.yaml, where it can be used by other Qcom
platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the link
comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned to
support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the 'iommu-map'
DT property and doesn't need BDF-to-SID translation (Qiang Yu)
* pci/controller/qcom:
PCI: qcom: Disable ASPM L0s for X1E80100
PCI: qcom: Remove BDF2SID mapping config for SC8280X family SoC
dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt
dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml
PCI: qcom: Add support for IPQ9574
dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller
PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert()
PCI: qcom: Enable MSI interrupts together with Link up if 'Global IRQ' is supported
- Add DT and driver support for using either of the two PolarFire Root
Ports (Conor Dooley)
* pci/controller/microchip:
PCI: microchip: Add support for using either Root Port 1 or 2
dt-bindings: PCI: microchip,pcie-host: Add reg for Root Port 2
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
* pci/controller/mediatek:
PCI: mediatek-gen3: Remove unneeded semicolon
PCI: mediatek-gen3: Add support for restricting link width
PCI: mediatek-gen3: Add support for setting max-link-speed limit
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root Complex
mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we can do
(Kishon Vijay Abraham I)
* pci/controller/keystone:
PCI: keystone: Add link up check to ks_pcie_other_map_bus()
PCI: keystone: Set mode as Root Complex for "ti,keystone-pcie" compatible
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100 us),
before deasserting PERST# to ensure power and refclk are stable
(Siddharth Vadapalli)
* pci/controller/j721e:
PCI: j721e: Deassert PERST# after a delay of PCIE_T_PVPERL_MS milliseconds
PCI: j721e: Add PCIe support for J722S SoC
- Fix suspend/resume support on i.MX6QDL, which has a hardware erratum that
prevents use of L2 (Stefan Eichenberger)
* pci/controller/imx6:
PCI: imx6: Fix suspend/resume support on i.MX6QDL
- Clear outbound address on unmap so dw_pcie_find_index() won't match an
ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when testing
for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Fix advertised resizable BAR size regression
PCI: dwc: Use of_property_present() for non-boolean properties
PCI: dwc: endpoint: Clear outbound address on unmap
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
* pci/controller/cadence:
PCI: cadence: Lower severity of message when phy-names property is absent in DTS
- Add pci_epc_function_is_valid() to avoid repeating common validation
checks (Damien Le Moal)
- Skip attempts to allocate from endpoint controller memory window if the
requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to handle
controller-specific size and alignment constraints, and add test cases to
the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can observe
DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent (Niklas
Cassel)
- Remove superfluous 'return' from pci_epf_test_clean_dma_chan() (Wang
Jiang)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks 'mmio' DT
property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid use-after-free
(Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when removing
the secondary controller associated with an NTB (Zijun Hu)
- Fix pci_epc_map map_size kerneldoc (Rick Wertenbroek)
* pci/endpoint:
PCI: endpoint: Fix pci_epc_map map_size kerneldoc string
PCI: endpoint: Clear secondary (not primary) EPC in pci_epc_remove_epf()
PCI: endpoint: Fix PCI domain ID release in pci_epc_destroy()
PCI: endpoint: epf-mhi: Avoid NULL dereference if DT lacks 'mmio'
PCI: endpoint: Remove surplus return statement from pci_epf_test_clean_dma_chan()
PCI: dwc: ep: Use align addr function for dw_pcie_ep_raise_{msi,msix}_irq()
PCI: endpoint: test: Synchronously cancel command handler work
PCI: dwc: endpoint: Implement the pci_epc_ops::align_addr() operation
PCI: endpoint: test: Use pci_epc_mem_map/unmap()
PCI: endpoint: Update documentation
PCI: endpoint: Introduce pci_epc_mem_map()/unmap()
PCI: endpoint: Improve pci_epc_mem_alloc_addr()
PCI: endpoint: Introduce pci_epc_function_is_valid()
- Add resource_set_size() to set resource size when start has already been
set (Ilpo Järvinen)
- Add resource_set_range() helper to set both resource start and size (Ilpo
Järvinen)
- Use IS_ALIGNED() and resource_size() in quirk_s3_64M() instead of
open-coding them (Ilpo Järvinen)
- Add ALIGN_DOWN_IF_NONZERO() to avoid code duplication when distributing
resources across devices (Ilpo Järvinen)
- Improve pdev_sort_resources() warning message to be more specific (Ilpo
Järvinen)
* pci/resource:
PCI: Improve pdev_sort_resources() warning message
PCI: Add ALIGN_DOWN_IF_NONZERO() helper
PCI: Use align and resource helpers, and SZ_* in quirk_s3_64M()
PCI: Use resource_set_{range,size}() helpers
resource: Add resource set range and size helpers
- Convert driver .remove_new() callbacks to .remove() again to finish the
conversion from returning 'int' to being 'void' (Sergio Paracuellos)
* pci/driver-remove:
PCI: acpiphp_ampere_altra: Switch back to struct platform_driver::remove()
PCI: controller: Switch back to struct platform_driver::remove()
Currently, the Rockchip PCIe endpoint controller driver does not handle
the PERST# signal, which prevents detecting when link training should
actually be started or if the host resets the device. This however can
be supported using the controller reset_gpios property set as an input
GPIO for endpoint mode.
Modify the Rockchip PCI endpoint controller driver to get the reset_gpio
and its associated interrupt which is serviced using a threaded IRQ with
the function rockchip_pcie_ep_perst_irq_thread() as handler.
This handler function notifies a link down event corresponding to the RC
side asserting the PERST# signal using pci_epc_linkdown() when the gpio
is high. Once the gpio value goes down, corresponding to the RC
de-asserting the PERST# signal, link training is started. The polarity
of the gpio interrupt trigger is changed from high to low after the RC
asserted PERST#, and conversely changed from low to high after the RC
de-asserts PERST#.
Also, given that the host mode controller and the endpoint mode
controller use two different property names for the same PERST# signal
(ep_gpios property and reset_gpios property respectively), for clarity,
rename the ep_gpio field of struct rockchip_pcie to perst_gpio.
Link: https://lore.kernel.org/r/20241017015849.190271-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: make log messages consistent, add missing include]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip RK3399 TRM V1.3 Part2, Section 17.5.8.1.2, step 7,
describes the endpoint mode link training process clearly and states
that:
Insure link training completion and success by observing link_st field
in PCIe Client BASIC_STATUS1 register change to 2'b11. If both side
support PCIe Gen2 speed, re-train can be Initiated by asserting the
Retrain Link field in Link Control and Status Register. The software
should insure the BASIC_STATUS0[negotiated_speed] changes to "1", that
indicates re-train to Gen2 successfully.
This procedure is very similar to what is done for the root-port mode
in rockchip_pcie_host_init_port().
Implement this link training procedure for the endpoint mode as well.
Given that the RK3399 SoC does not have an interrupt signaling link
status changes, training is implemented as a delayed work which is
rescheduled until the link training completes or the endpoint controller
is stopped. The link training work is first scheduled in
rockchip_pcie_ep_start() when the endpoint function is started. Link
training completion is signaled to the function using pci_epc_linkup().
Accordingly, the linkup_notifier field of the Rockchip pci_epc_features
structure is changed to true.
Link: https://lore.kernel.org/r/20241017015849.190271-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: update log messages to make them consistent]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define the EPC operation ->stop() for the Rockchip endpoint driver with
the function rockchip_pcie_ep_stop(). This function disables link
training and the controller configuration, as the reverse to what
the start operation defined with rockchip_pcie_ep_start() does.
Link: https://lore.kernel.org/r/20241017015849.190271-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function rockchip_pcie_init_port() enables link training for a
controller configured in EP mode. Enabling link training is again done
in rockchip_pcie_ep_probe() after that function executed
rockchip_pcie_init_port(). Enabling link training only needs to be done
once, and doing so at the probe stage before the controller is actually
started by the user serves no purpose.
Refactor this by removing the link training enablement from both
rockchip_pcie_init_port() and rockchip_pcie_ep_probe() and moving it to
the endpoint start operation defined with rockchip_pcie_ep_start().
Enabling the controller configuration using the PCIE_CLIENT_CONF_ENABLE
bit in the same PCIE_CLIENT_CONFIG register is also moved to
rockchip_pcie_ep_start() and both the controller configuration and link
training enable bits are set with a single call to
rockchip_pcie_write().
Link: https://lore.kernel.org/r/20241017015849.190271-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the code in rockchip_pcie_ep_probe() to hide the MSI-X capability
to its own function, rockchip_pcie_ep_hide_broken_msix_cap().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Introduce the function rockchip_pcie_ep_init_ob_mem() allocate the
outbound memory regions and memory needed for IRQ handling.
These changes tidy up rockchip_pcie_ep_probe().
No functional change.
Link: https://lore.kernel.org/r/20241017015849.190271-9-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To be consistent with the usual "get_resources" naming of driver
functions that acquire controller resources like clocks, PHY etc,
rename the function rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The call to rockchip_pcie_prog_ep_ob_atu() used to map the PCI address
of MSI data to the memory window allocated on probe for IRQs is done
in rockchip_pcie_ep_send_msi_irq() assuming a fixed alignment to a
256B boundary of the PCI address. This is not correct as the alignment
constraint for the RK3399 PCI mapping depends on the number of bits of
address changing in the mapped region. This leads to an unstable system
which sometimes work and sometimes does not (crashing on paging faults
when memcpy_toio() or memcpy_fromio() are used).
Similar to regular data mapping, the MSI data mapping must thus be
handled according to the information provided by
rockchip_pcie_ep_align_addr(). Modify rockchip_pcie_ep_send_msi_irq()
to use rockchip_pcie_ep_align_addr() to correctly program entry 0 of
the ATU for sending MSI IRQs.
Link: https://lore.kernel.org/r/20241017015849.190271-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits from the CPU address space used for the
mapping. For a PCI mapping of size bytes starting from pci_addr, the
number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1], up to 20 bits, that is,
up to 1MB mappings.
This means that when preparing a PCI address mapping, an endpoint
function driver must use an offset into the allocated controller
memory region that is equal to the mask of the starting PCI address
over rockchip_pcie_ep_ob_atu_num_bits() bits. This offset also
determines the maximum size of the mapping given the starting PCI
address and the fixed 1MB controller memory window size.
Implement the ->align_addr() endpoint controller operation to allow the
mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/r/20241017015849.190271-6-dlemoal@kernel.org
Co-developed-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: change local variable name for address offset]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a check to verify that the outbound region to be used for mapping an
address is not already in use.
Link: https://lore.kernel.org/r/20241017015849.190271-5-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to loop over all regions to find the memory window used
to map an address. We can use rockchip_ob_region() to determine the
region index, together with a check that the address passed as argument
is the address used to create the mapping. Furthermore, the
ob_region_map bitmap should also be checked to ensure that we are not
attempting to unmap an address that is not mapped.
Link: https://lore.kernel.org/r/20241017015849.190271-4-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce the macro ROCKCHIP_PCIE_AT_SIZE_ALIGN to initialize the .align
field of the controller epc_features structure to 256. This is defined
as a shift using the macro ROCKCHIP_PCIE_AT_MIN_NUM_BITS (to avoid
using the "magic" value 8 directly).
Link: https://lore.kernel.org/r/20241017015849.190271-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Link: https://lore.kernel.org/r/20241104190714.275977-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use the dw_pcie_ep_align_addr() function to calculate the alignment in
dw_pcie_ep_raise_{msi,msix}_irq() instead of open coding the same.
Link: https://lore.kernel.org/r/20241017132052.4014605-6-cassel@kernel.org
Link: https://lore.kernel.org/r/20241104205144.409236-2-cassel@kernel.org
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: squashed patch that fixes memory map sizes]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A PCI controller device, e.g., StarFive, is parent to PCI host bridge
device. We must enable runtime PM of the controller before enabling runtime
PM of the host bridge, which will happen in pci_host_probe(), to avoid this
warning:
pcie-starfive 940000000.pcie: Enabling runtime PM for inactive device with active children
Fix this issue by enabling StarFive controller device's runtime PM before
calling pci_host_probe() in plda_pcie_host_init().
Link: https://lore.kernel.org/r/20241111-runtime_pm-v7-1-9c164eefcd87@quicinc.com
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Remove a surplus semicolon and fix the following warning:
./drivers/pci/controller/pcie-mediatek-gen3.c:414:2-3: Unneeded semicolon
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11789
Link: https://lore.kernel.org/r/20241111010935.20208-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The "phy-names" property is optional, so the message indicating its
absence during the probe should be of "info" severity rather than
"error" severity.
Link: https://lore.kernel.org/r/20241018113045.2050295-1-bwawrzyn@cisco.com
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
[kwilczynski: update log messages wording, commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
K2G forwards the error triggered by a link-down state (e.g., no connected
endpoint device) on the system bus for PCI configuration transactions;
these errors are reported as an SError at system level, which is fatal and
hangs the system.
So, apply fix similar to how it was done in the DesignWare Core driver
commit 15b2390634 ("PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()").
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Link: https://lore.kernel.org/r/20240524105714.191642-3-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
commit 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x
Platforms") introduced configuring "enum dw_pcie_device_mode" as part of
device data ("struct ks_pcie_of_data"). However it failed to set the
mode for "ti,keystone-pcie" compatible.
Since the mode defaults to "DW_PCIE_UNKNOWN_TYPE", the following error
message is displayed for the v3.65a controller:
"INVALID device type 0"
Despite the driver probing successfully, the controller may not be
functional in the Root Complex mode of operation.
So, set the mode as Root Complex for "ti,keystone-pcie" compatible to
fix this.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Link: https://lore.kernel.org/r/20240524105714.191642-2-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
The PCI host controller on PolarFire SoC has multiple Root Port instances,
each with their own bridge and ctrl address spaces. The original binding
has an "apb" register region, and it is expected to be set to the base
address of the Root Complex register space. Some defines in the Linux
driver were used to compute the addresses of the bridge and ctrl address
ranges corresponding to Root Port instance 1. Some customers want to use
Root Port instance 2 however, which requires changing the defines in the
driver, which is clearly not a portable solution.
The binding has been changed from a single register region to a pair,
corresponding to the bridge and ctrl regions respectively, so modify the
driver to read these regions directly from the devicetree rather than
compute them from the base address of the abp region.
To maintain backwards compatibility with the existing binding, the driver
retains code to handle the "abp" reg and computes the base address of the
bridge and ctrl regions using the defines if it is present. reg-names has
always been a required property, so this is safe to do.
Link: https://lore.kernel.org/r/20241107-surrender-brisket-287d563a5de1@spud
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[bhelgaas: Capitalize PCIe spec terms]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The remapped PCIe Root Port and the child device have PM L1 Substates
capability, but they are disabled originally.
Here is a failed example on ASUS B1400CEAE:
Capabilities: [900 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+
PortCommonModeRestoreTime=32us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=101376ns
L1SubCtl2: T_PwrOn=50us
Enable PCI-PM L1 PM Substates for devices below VMD while they are in D0
(see PCIe r6.0, sec 5.5.4).
Link: https://lore.kernel.org/r/20241001083438.10070-4-jhp@endlessos.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Add support for this VMD device which supports the bus restriction mode.
The feature that turns off vector 0 for MSI-X remapping is also enabled.
Link: https://lore.kernel.org/r/20241011175657.249948-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.ntel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The suspend/resume functionality is currently broken on the i.MX6QDL
platform, as documented in the NXP errata (ERR005723):
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
This patch addresses the issue by sharing most of the suspend/resume
sequences used by other i.MX devices, while avoiding modifications to
critical registers that disrupt the PCIe functionality. It targets the
same problem as the following downstream commit:
4e92355e1f
Unlike the downstream commit, this patch also resets the connected PCIe
device if possible. Without this reset, certain drivers, such as ath10k
or iwlwifi, will crash on resume. The device reset is also done by the
driver on other i.MX platforms, making this patch consistent with
existing practices.
Upon resuming, the kernel will hang and display an error. Here's an
example of the error encountered with the ath10k driver:
ath10k_pci 0000:01:00.0: Unable to change power state from D3hot to D0, device inaccessible
Unhandled fault: imprecise external abort (0x1406) at 0x0106f944
Without this patch, suspend/resume will fail on i.MX6QDL devices if a
PCIe device is connected.
Link: https://lore.kernel.org/r/20241030103250.83640-1-eichest@gmail.com
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: stable@vger.kernel.org
Add support for restricting the port's link width by specifying
the num-lanes devicetree property in the PCIe node.
The setting is done in the GEN_SETTINGS register (in the driver
named as PCIE_SETTING_REG), where each set bit in [11:8] activates
a set of lanes (from bits 11 to 8 respectively, x16/x8/x4/x2).
Link: https://lore.kernel.org/r/20241104114935.172908-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function dw_pcie_prog_outbound_atu() used to program outbound ATU
entries for mapping RC PCI addresses to local CPU addresses does not
allow PCI addresses that are not aligned to the value of region_align
of struct dw_pcie. This value is determined from the iATU hardware
registers during probing of the iATU (done by dw_pcie_iatu_detect()).
This value is thus valid for all DWC PCIe controllers, and valid
regardless of the hardware configuration used when synthesizing the
DWC PCIe controller.
Implement the ->align_addr() endpoint controller operation to allow
this mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/linux-pci/20241012113246.95634-7-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241015090712.112674-1-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241017132052.4014605-5-cassel@kernel.org
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[mani: squashed the patch that changed phy_addr_t to u64]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: squashed patch that updated the pci_size variable]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for respecting the max-link-speed devicetree property,
forcing a maximum speed (Gen) for a PCI-Express port.
Since the MediaTek PCIe Gen3 controllers also expose the maximum
supported link speed in the PCIE_BASE_CFG register, if property
max-link-speed is specified in devicetree, validate it against the
controller capabilities and proceed setting the limitations only
if the wanted Gen is lower than the maximum one that is supported
by the controller itself (otherwise it makes no sense!).
Link: https://lore.kernel.org/r/20241104114935.172908-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[kwilczynski: change dev_dbg() to dev_info() and update message wording]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the cfg_1_9_0 which is being used for X1E80100 doesn't disable
ASPM L0s. However, hardware team recommends to disable L0s as the PHY init
sequence is not tuned support L0s. Hence reuse cfg_sc8280xp for X1E80100.
Note that the config_sid() callback is not present in cfg_sc8280xp, don't
concern about this because config_sid() callback is originally a no-op
for X1E80100.
Fixes: 6d0c39324c ("PCI: qcom: Add X1E80100 PCIe support")
Link: https://lore.kernel.org/r/20241101030902.579789-5-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9
The SC8280XP PCIe devicetree nodes do not specify an 'iommu-map' so
the config_sid() callback is effectively a no-op.
Hence introduce a new ops struct, namely ops_1_21_0 which is same as
ops_1_9_0 except that it doesn't have config_sid() callback to clean
it up.
Link: https://lore.kernel.org/r/20241101030902.579789-4-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
According to Section 2.2 of the PCI Express Card Electromechanical
Specification (Revision 5.1), in order to ensure that the power and the
reference clock are stable, PERST# has to be deasserted after a delay of
100 milliseconds (TPVPERL).
Currently, it is being assumed that the power is already stable, which
is not necessarily true.
Hence, change the delay to PCIE_T_PVPERL_MS to guarantee that power and
reference clock are stable.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Fixes: f96b697137 ("PCI: j721e: Use T_PERST_CLK_US macro")
Link: https://lore.kernel.org/r/20241104074420.1862932-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add the new IPQ9574 platform which is based on the Qcom IP rev. 1.27.0
and Synopsys IP rev. 5.80a.
The platform itself has four PCIe Gen3 controllers: two single-lane and
two dual-lane, all are based on Synopsys IP rev. 5.70a. As such, reuse
all the members of 'ops_2_9_0'.
Link: https://lore.kernel.org/r/20240801054803.3015572-5-quic_srichara@quicinc.com
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
TI's J722S SoC has one instance of PCIe namely PCIe0 which is a Gen3
single lane PCIe controller. Add support for the "ti,j722s-pcie-host"
compatible specific to J722S SoC.
Link: https://lore.kernel.org/r/20240524092349.158443-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of pex_ep_event_pex_rst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the tegra194 endpoint SoCs supported as of now depend on the refclk
from the host for keeping the controller operational. Due to this
limitation, any access to the hardware registers in the absence of refclk
will result in a whole endpoint crash. Unfortunately, most of the
controller cleanups require accessing the hardware registers (like eDMA
cleanup performed in dw_pcie_ep_cleanup(), etc...). So these cleanup
functions can cause the crash in the endpoint SoC once host asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host.
Thus, fix this crash by moving the controller cleanups to the start of
the pex_ep_event_pex_rst_deassert() function. This function is called
whenever the host has deasserted PERST# and it is guaranteed that the
refclk would be active at this point. So at the start of this function
(after enabling resources) the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-2-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of qcom_pcie_perst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the Qcom endpoint SoCs supported as of now depend on the refclk from
the host for keeping the controller operational. Due to this limitation,
any access to the hardware registers in the absence of refclk will result
in a whole endpoint crash. Unfortunately, most of the controller cleanups
require accessing the hardware registers (like eDMA cleanup performed in
dw_pcie_ep_cleanup(), powering down MHI EPF etc...). So these cleanup
functions are currently causing the crash in the endpoint SoC once host
asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host (as I was told by the Qcom engineers).
Thus, fix this crash by moving the controller cleanups to the start of
the qcom_pcie_perst_deassert() function. qcom_pcie_perst_deassert() is
called whenever the host has deasserted PERST# and it is guaranteed that
the refclk would be active at this point. So at the start of this function
(after enabling resources), the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-1-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently, if 'Global IRQ' is supported by the platform, only the Link up
interrupt is enabled in the PARF_INT_ALL_MASK register. This masks MSIs
on some platforms. The MSI bits in PARF_INT_ALL_MASK register are enabled
by default in the hardware, but commit 4581403f67 ("PCI: qcom: Enumerate
endpoints based on Link up event in 'global_irq' interrupt") disabled them
and enabled only the Link up interrupt. While MSI continued to work on the
SM8450 platform that was used to test the offending commit, on other
platforms like SM8250, X1E80100, MSIs are getting masked. And they require
enabling the MSI interrupt bits in the register to unmask (enable) the
MSIs.
Even though the MSI interrupt enable bits in PARF_INT_ALL_MASK are
described as 'diagnostic' interrupts in the internal documentation,
disabling them masks MSI on these platforms. Due to this, MSIs were not
reported to be received these platforms while supporting 'Global IRQ'.
So, enable the MSI interrupts along with the Link up interrupt in the
PARF_INT_ALL_MASK register if 'Global IRQ' is supported. This ensures that
the MSIs continue to work and also the driver is able to catch the Link
up interrupt for enumerating endpoint devices.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Closes: https://lore.kernel.org/linux-pci/9a692c98-eb0a-4d86-b642-ea655981ff53@kernel.org/
Link: https://lore.kernel.org/r/20241007051255.4378-1-manivannan.sadhasivam@linaro.org
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SL7
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Qiang Yu <quic_qianyu@quicinc.com>
Clear the address mapped (outbound_addr array) in dw_pcie_ep_unmap_addr(),
to ensure that dw_pcie_find_index() does not match an ATU index that was
already unmapped.
This is in addition to clearing the ATU index bit in ob_window_map.
Link: https://lore.kernel.org/linux-pci/20241004141000.5080-1-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Convert open-coded resource size calculations to use
resource_set_{range,size}() helpers.
While at it, use SZ_* for size parameter where appropriate which makes the
intent of code more obvious.
Also, cast sizes to resource_size_t, not u64.
Link: https://lore.kernel.org/r/20240614100606.15830-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove() return
void") .remove() is (again) the right callback to implement for platform
drivers.
Convert all PCI controller drivers to use .remove(), with the eventual goal
to drop struct platform_driver::remove_new(). As .remove() and .remove_new()
have the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Link: https://lore.kernel.org/r/20240923065706.728769-1-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[bhelgaas: add pcie-xilinx-nwl.c and tidy whitespace per Uwe Kleine-König:
https://lore.kernel.org/r/tdxrmmqyzcufupnwkdbg7lwgadizm7v3lxjirykijbml7x54ze@upbdzycdsilm]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=L3s9
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
- Fix off-by-one error in INTx IRQ handler that caused INTx interrupts to
be lost or delivered as the wrong interrupt (Sean Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT binding
and xilinx-dma-pl driver (Thippeswamy Havalige)
* pci/controller/xilinx:
PCI: xilinx-xdma: Add Xilinx QDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx QDMA PCIe Root Port Bridge
arm64: zynqmp: Add PCIe phys property for ZCU102
PCI: xilinx-nwl: Add PHY support
dt-bindings: pci: xilinx-nwl: Add phys property
PCI: xilinx-nwl: Clean up clock on probe failure/removal
PCI: xilinx-nwl: Rate-limit misc interrupt messages
PCI: xilinx-nwl: Fix register misspelling
PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
- Add DT "ti,syscon-acspcie-proxy-ctrl" and driver support to enable the
ACSPCIE module to drive Refclk for the Endpoint (Siddharth Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link setup
can be done separately during resume (Thomas Richard)
- Use dev_err_probe() to simplify j721e probe (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between Refclk
becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
* pci/controller/j721e:
PCI: j721e: Add suspend and resume support
PCI: j721e: Use T_PERST_CLK_US macro
PCI: Add T_PERST_CLK_US macro
PCI: j721e: Add reset GPIO to struct j721e_pcie
PCI: j721e: Use dev_err_probe() in the probe() function
PCI: cadence: Set cdns_pcie_host_init() global
PCI: cadence: Extract link setup sequence from cdns_pcie_host_setup()
PCI: j721e: Enable ACSPCIE Refclk if "ti,syscon-acspcie-proxy-ctrl" exists
dt-bindings: PCI: ti,j721e-pci-host: Add ACSPCIE proxy control property
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler
is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe (Siddharth
Vadapalli)
* pci/controller/dra7xx:
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
- Change DT binding maintainer to Jim Quinlan (Jim Quinlan)
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Refactor .probe() error handling (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add SoC-specific HARD_DEBUG, INTR2_CPU_BASE register offsets (Jim
Quinlan)
- Drop unused RGR1_SW_INIT_1_INIT_MASK, RGR1_SW_INIT_1_INIT_SHIFT offsets
(Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller doesn't
imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Check return values of all reset_control_*() calls (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
* pci/controller/brcmstb:
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
PCI: brcmstb: Enable 7712 SoCs
PCI: brcmstb: Change field name from 'type' to 'soc_base'
PCI: brcmstb: Check return value of all reset_control_* calls
PCI: brcmstb: Refactor for chips with many regular inbound windows
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
PCI: brcmstb: Remove two unused constants from driver
PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific
PCI: brcmstb: Use swinit reset if available
PCI: brcmstb: Use bridge reset if available
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
dt-bindings: PCI: brcm,stb-pcie: Add 7712 SoC description
dt-bindings: PCI: brcm,stb-pcie: Use maxItems for reset controllers
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same thing
and is what other drivers use (Jinjie Ruan)
* pci/controller/altera:
PCI: altera: Replace TLP_REQ_ID() with macro PCI_DEVID()
Commit d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq()
call to the bottom of probe") moved the IRQ request for
"dra7xx-pcie-main" towards the end of dra7xx_pcie_probe().
However, the error handling does not take into account the
initialization performed by either dra7xx_add_pcie_port() or
dra7xx_add_pcie_ep(), depending on the mode of operation.
Fix the error handling to address this.
Fixes: d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe")
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-3-s-vadapalli@ti.com
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Commit da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for
"dra7xx-pcie-main" IRQ") switched from devm_request_irq() to
devm_request_threaded_irq() for the "dra7xx-pcie-main" interrupt.
Since the primary handler was set to NULL, the "IRQF_ONESHOT" flag
should have also been set. Fix this.
Fixes: da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ")
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-2-s-vadapalli@ti.com
Reported-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate.
These settings improve link stability while operating at high date
rates and helps to improve signal quality.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the dw_pcie::max_link_speed has a valid value only if the
controller driver restricts the maximum link speed in the driver or if
the platform does so in the devicetree using the 'max-link-speed'
property.
But having the maximum supported link speed of the platform would be
helpful for the vendor drivers to configure any link specific settings.
So in the case of non-valid value in dw_pcie::max_link_speed, just cache
the hardware default value from Link Capability register.
While at it, remove the 'max_link_speed' argument to the
dw_pcie_link_set_max_speed() function since the value can be
retrieved within the function.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-2-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
qcom_pcie_enable_resources() is called by qcom_pcie_ep_probe() and it
enables the controller resources like clocks, regulator, PHY. On one of the
new unreleased Qcom SoC, PHY enablement depends on the active refclk. And
on all of the supported Qcom endpoint SoCs, refclk comes from the host
(RC). So calling qcom_pcie_enable_resources() without refclk causes the
NoC (Network On Chip) error in the endpoint SoC and in turn results in a
whole SoC crash and rebooting into EDL (Emergency Download) mode which is
an unrecoverable state.
But qcom_pcie_enable_resources() is already called by
qcom_pcie_perst_deassert() when PERST# is deasserted, and refclk is
available at that time.
Hence, remove the unnecessary call to qcom_pcie_enable_resources() from
qcom_pcie_ep_probe() to prevent the above mentioned crash.
It should be noted that this commit prevents the crash only under normal
working condition (booting endpoint before host), but the crash may also
occur if PERST# assert happens at the wrong time. For avoiding the crash
completely, it is recommended to use SRIS mode which allows the endpoint
SoC to generate its own refclk. The driver is not supporting SRIS mode
currently, but will be added in the future.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Link: https://lore.kernel.org/linux-pci/20240830082319.51387-1-manivannan.sadhasivam@linaro.org
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Implement i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe Root Complex
(RC) support. While the controller resembles that of i.MX8MP, the PHY
differs significantly. Also, there's a distinction between PCI bus
addresses and CPU addresses.
Introduce IMX_PCIE_FLAG_CPU_ADDR_FIXUP in drvdata::flags to indicate driver
need the cpu_addr_fixup() callback to facilitate CPU address to PCI bus
address conversion according to "ranges" property.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-11-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: check resource_list_first_type() for NULL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PCIe r6.0 changed the abbreviation for "Configuration Request Retry Status"
Completion Status from "CRS" to "RRS" and uses the terminology of
"Configuration RRS Software Visibility" instead of "CRS Software
Visibility".
Align the Linux usage with the r6.0 spec language. No functional change
intended.
It's confusing to make this change, but I think "RRS" *is* a better
abbreviation because it was easy to interpret "CRS" as "Completion Retry
Status", which really didn't make any sense.
Link: https://lore.kernel.org/r/20240827234848.4429-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r6.0, sec 2.3.2, when a Root Complex handles a Completion with
Request Retry Status for a Configuration Read Request that includes both
bytes of the Vendor ID field, it must complete the Request to the host by
returning 0001h for the Vendor ID and all 1's for any additional bytes.
Previously we only returned the 0001h Vendor ID value if we got an RRS
completion for reads of exactly 4 bytes. A read of 2 bytes would not
qualify, although the spec says it should.
Check for reads of 2 or more bytes including the Vendor ID.
I don't think this will fix any observable problems because RRS only
applies to the first config reads after reset, and those are all currently
dword (4-byte) reads.
Link: https://lore.kernel.org/r/20240827234848.4429-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Sort enum pcie_soc_base values.
Rename pcie_offsets_bmips_7425[] to pcie_offsets_bcm7425[] to match BCM7425
pcie_soc_base enum, bcm7425_cfg, and "brcm,bcm7425-pcie" .compatible
string.
Rename pcie_offset_bcm7278[] to pcie_offsets_bcm7278[] to match other
"pcie_offsets" names.
Rename pcie_offset_bcm7712[] to pcie_offsets_bcm7712[] to match other
"pcie_offsets" names.
Sort pcie_offsets_*[] by SoC name, move them all together, indent values
for easy reading.
Sort pcie_cfg_data structs by SoC name.
Sort .compatible strings by SoC name.
No functional change intended.
Link: https://lore.kernel.org/r/20240902205456.227409-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Invoke the common PHY API to configure mode, speed, and submode. While
these functions are optional in the PHY interface, they are necessary for
certain PHY drivers. Lack of support for these functions in a PHY driver
does not cause harm.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-10-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Consolidated redundant if-checks pertaining to imx_pcie->phy. Instead of
two separate checks, merged them into one to improve code readability.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-8-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to assert/dassert the core
reset handled by this driver itself, let's introduce a new callback
core_reset() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to enable/disable the
reference clock handled by this driver itself, let's introduce a new
callback enable_ref_clk() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since this driver has evolved to support other i.MX SoCs such as
i.MX7/8/9, thus rename the 'imx6' prefix to 'imx' to avoid confusion.
The driver name is left unchanged to avoid breaking userspace.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log, refactor the IMX_* macros]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fix missing call to phy_power_off() in the error path of
imx6_pcie_host_init(). Remove unnecessary check for imx6_pcie->phy
as the PHY API already handles NULL pointers.
Fixes: cbcf8722b5 ("phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.1+
Correct occasional MSI triggering failures in i.MX8MP PCIe EP by applying
the correct hardware outbound alignment requirement.
The i.MX platform has a restriction about outbound address translation. The
pci-epc-mem uses page_size to manage it. Set the correct page_size for i.MX
platform to meet the hardware requirement, which is the same as inbound
address alignment.
Thus, align it with epc_features::align.
Fixes: 1bd0d43dcf ("PCI: imx6: Clean up addr_space retrieval code")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-2-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Cc: <stable@vger.kernel.org> # 6.9+
Add IMX6_PCIE_FLAG_HAS_APP_RESET flag to IMX8MM_EP and IMX8MP_EP drvdata.
This flag was overlooked during code restructuring. It is crucial to
release the app-reset from the System Reset Controller before initiating
LTSSM to rectify the issue.
Fixes: 0c9651c21f ("PCI: imx6: Simplify reset handling by using *_FLAG_HAS_*_RESET")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-1-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9+
The Broadcom STB 7712 is the sibling chip of the RPi 5 (2712). It has
one PCIe controller with a single port, supports gen2 and one lane only.
The current revision of the chip is "C0" or "C1".
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-14-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
The 'type' field used in the driver to discern SoC differences is
confusing; change it to the more apt 'soc_base'.
The 'base' is because some SoCs have the same characteristics as
previous SoCs so it is convenient to classify them in the same group.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-13-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Always check the return value for invocations of reset_control_xxx() and
propagate the error to the next level.
Although the current functions in reset-brcmstb.c cannot fail, this may
someday change.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-12-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Provide support for new chips with multiple inbound windows while
keeping the legacy support for the older chips.
In existing chips there are three inbound windows with fixed purposes:
the first was for mapping SoC internal registers, the second was for
memory, and the third was for memory but with the endian swapped.
Typically, only one window was used.
Complicating the inbound window usage was the fact that the PCIe HW
would do a baroque internal mapping of system memory, and concatenate
the regions of multiple memory controllers.
Newer chips such as the 7712 and Cable Modem SoCs take a step forward
and drop the internal mapping while providing for multiple inbound
windows. This works in concert with the dma-ranges property, where each
provided range becomes an inbound window.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-11-james.quinlan@broadcom.com
Co-developed-by: Riyan Dhiman <riyandhiman14@gmail.com>
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log, wrap code comments to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Within kirin_pcie_parse_port(), the pcie->num_slots is compared to
pcie->gpio_id_reset size (MAX_PCI_SLOTS) which is correct and would lead
to an overflow.
Thus, fix condition to pcie->num_slots + 1 >= MAX_PCI_SLOTS and move
pcie->num_slots increment below the if-statement to avoid out-of-bounds
array access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: b22dbbb245 ("PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge")
Link: https://lore.kernel.org/linux-pci/20240903115823.30647-1-adiupina@astralinux.ru
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TLP_REQ_ID's function is same as current PCI_DEVID()
macro, replace it.
No functional changes intended.
Link: https://lore.kernel.org/linux-pci/20240828104202.3683491-1-ruanjinjie@huawei.com
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add suspend and resume support. Only the Root Complex mode is supported.
During the suspend stage PERST# is asserted, then deasserted during the
resume stage.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-7-a2f9156da6c3@bootlin.com
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
[kwilczynski: commit log, update references to the PCI SIG specification]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Add a "has_phy" field indicating that the internal PHY has SW control
that requires configuration. Some previous chips only required the
firing of the "rescal" reset controller.
This change requires us to give the 7216 SoC its own cfg_data structure.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-10-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Remove two constants in the driver which are no longer
used: RGR1_SW_INIT_1_INIT_MASK and RGR1_SW_INIT_1_INIT_SHIFT.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-9-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Do preparatory work for the 7712 SoC, which is introduced in a
future commit.
Our HW design has changed two register offsets for the 7712, where
previously it was a common value for all Broadcom SoCs with PCIe
cores.
Specifically, the two offsets are to the registers HARD_DEBUG and
INTR2_CPU_BASE.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-8-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
The 7712 SoC adds a software init reset device for the PCIe HW.
If found in the DT node, use it.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 7712 SoC has a bridge reset which can be described in the device
tree.
Use it if present. Otherwise, continue to use the legacy method to
reset the bridge.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log, refactored function brcm_pcie_bridge_sw_init_set_generic()]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Refactor the error handling in the bottom half of the probe function
for readability.
The invocation of clk_prepare_enable() is moved lower in the function
and this simplifies a couple of return paths. The dev_err_probe() is
also used when it is apt.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Struct cdns_pcie_rc once had a .dev member, but it was removed by
bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library").
Drop the extra kerneldoc for it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Struct mtk_pcie.mem was removed by 8a26f861b8 ("PCI: mediatek: Use
pci_parse_request_of_pci_ranges()"), but the kerneldoc was left. Remove
the extra kerneldoc.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add reset GPIO to struct j721e_pcie, so it can be used at suspend and
resume stages.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-4-a2f9156da6c3@bootlin.com
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Use dev_err_probe() instead of dev_err() in the probe() function to
simplify the code and standardize the error output.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-3-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
During the resume sequence of the host, cdns_pcie_host_init() needs to be
called, so set it global.
The dev function parameter is removed, as it isn't used.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-2-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The function cdns_pcie_host_setup() mixes probe structure and link setup.
The link setup must be done during the resume sequence. So extract it from
cdns_pcie_host_setup() and create a dedicated function.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-1-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Introduce support for Airoha EN7581 PCIe controller to mediatek-gen3
PCIe controller driver.
Link: https://lore.kernel.org/linux-pci/aca00bd672ee576ad96d279414fc0835ff31f637.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Use reset_bulk APIs to manage PHY reset lines.
This is a preliminary patch in order to add Airoha EN7581 PCIe support.
Link: https://lore.kernel.org/linux-pci/3ceb83bc0defbcf868521f8df4b9100e55ec2614.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Introduce mtk_gen3_pcie_pdata data structure in order to define
multiple callbacks for each supported SoC.
This is a preliminary patch to introduce EN7581 PCIe support.
Link: https://lore.kernel.org/linux-pci/c193d1a87505d045e2e0ef33317bce17012ee095.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Don't populate the const read-only array check_addr on the stack at
run time, instead make it static.
Link: https://lore.kernel.org/linux-pci/20240822205941.643187-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
[kwilczynski: refactor array definition]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The code in vmd_shutdown() had an indentation issue where spaces were
used instead of tabs. This commit corrects the indentation to use tabs,
adhering to the Linux kernel coding style guidelines.
Issue reported by the checkpatch.pl script:
ERROR: code indent should use tabs where possible
#1056: FILE: drivers/pci/controller/vmd.c:1056:
+ struct vmd_dev *vmd = pci_get_drvdata(dev);$
WARNING: please, no spaces at the start of a line
#1056: FILE: drivers/pci/controller/vmd.c:1056:
+ struct vmd_dev *vmd = pci_get_drvdata(dev);$
ERROR: code indent should use tabs where possible
#1058: FILE: drivers/pci/controller/vmd.c:1058:
+ vmd_remove_irq_domain(vmd);$
WARNING: please, no spaces at the start of a line
#1058: FILE: drivers/pci/controller/vmd.c:1058:
+ vmd_remove_irq_domain(vmd);$
No functional changes are intended.
Link: https://lore.kernel.org/linux-pci/20240901092602.17414-1-riyandhiman14@gmail.com
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
PARF hardware block which is a wrapper on top of DWC PCIe controller
mirrors the DBI and ATU register space. It uses PARF_SLV_ADDR_SPACE_SIZE
register to get the size of the memory block to be mirrored and uses
PARF_DBI_BASE_ADDR, PARF_ATU_BASE_ADDR registers to determine the base
address of DBI and ATU space inside the memory block that is being
mirrored.
When a memory region which is located above the SLV_ADDR_SPACE_SIZE
boundary is used for BAR region then there could be an overlap of DBI and
ATU address space that is getting mirrored and the BAR region. This
results in DBI and ATU address space contents getting updated when a PCIe
function driver tries updating the BAR/MMIO memory region. Reference
memory map of the PCIe memory region with DBI and ATU address space
overlapping BAR region is as below.
|---------------|
| |
| |
------- --------|---------------|
| | |---------------|
| | | DBI |
| | |---------------|---->DBI_BASE_ADDR
| | | |
| | | |
| PCIe | |---->2*SLV_ADDR_SPACE_SIZE
| BAR/MMIO|---------------|
| Region | ATU |
| | |---------------|---->ATU_BASE_ADDR
| | | |
PCIe | |---------------|
Memory | | DBI |
Region | |---------------|---->DBI_BASE_ADDR
| | | |
| --------| |
| | |---->SLV_ADDR_SPACE_SIZE
| |---------------|
| | ATU |
| |---------------|---->ATU_BASE_ADDR
| | |
| |---------------|
| | DBI |
| |---------------|---->DBI_BASE_ADDR
| | |
| | |
----------------|---------------|
| |
| |
| |
|---------------|
Currently memory region beyond the SLV_ADDR_SPACE_SIZE boundary is not
used for BAR region which is why the above mentioned issue is not
encountered. This issue is discovered as part of internal testing when we
tried moving the BAR region beyond the SLV_ADDR_SPACE_SIZE boundary. Hence
we are trying to fix this.
As PARF hardware block mirrors DBI and ATU register space after every
PARF_SLV_ADDR_SPACE_SIZE (default 0x1000000) boundary multiple, program
maximum possible size to this register by writing 0x80000000 to it(it
considers only powers of 2 as values) to avoid mirroring DBI and ATU to
BAR/MMIO region. Write the physical base address of DBI and ATU register
blocks to PARF_DBI_BASE_ADDR (default 0x0) and PARF_ATU_BASE_ADDR (default
0x1000) respectively to make sure DBI and ATU blocks are at expected
memory locations.
The register offsets PARF_DBI_BASE_ADDR_V2, PARF_SLV_ADDR_SPACE_SIZE_V2
and PARF_ATU_BASE_ADDR are applicable for platforms that use Qcom IP
rev 1.9.0, 2.7.0 and 2.9.0. PARF_DBI_BASE_ADDR_V2 and
PARF_SLV_ADDR_SPACE_SIZE_V2 are applicable for Qcom IP rev 2.3.3.
PARF_DBI_BASE_ADDR and PARF_SLV_ADDR_SPACE_SIZE are applicable for Qcom
IP rev 1.0.0, 2.3.2 and 2.4.0. Update init()/post_init() functions of the
respective Qcom IP versions to program applicable PARF_DBI_BASE_ADDR,
PARF_SLV_ADDR_SPACE_SIZE and PARF_ATU_BASE_ADDR register offsets. Update
the SLV_ADDR_SPACE_SZ macro to 0x80000000 to set highest bit in
PARF_SLV_ADDR_SPACE_SIZE register.
Cache DBI and iATU physical addresses in 'struct dw_pcie' so that
pcie_qcom.c driver can program these addresses in the PARF_DBI_BASE_ADDR
and PARF_ATU_BASE_ADDR registers.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20240814220338.1969668-1-quic_pyarlaga@quicinc.com
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
Historically, Qcom PCIe RC controllers lacked standard hotplug support. So
when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. But this can be avoided by using the Link
up event exposed by the Qcom specific 'global_irq' interrupt.
Qcom PCIe RC controllers are capable of generating the 'global' SPI
interrupt to the host CPUs. The device driver can use this interrupt to
identify events such as PCIe link specific events, safety events etc...
One such event is the PCIe Link up event generated when an endpoint is
detected on the bus and the Link is 'up'. This event can be used to
enumerate the PCIe endpoint devices without user intervention.
So add support for capturing the PCIe Link up event using the 'global'
interrupt in the driver. Once the Link up event is received, the bus
underneath the host bridge is scanned to enumerate PCIe endpoint devices.
All of the Qcom SoCs have only one Root Port per controller instance. So
only a single 'Link up' event is generated for the PCIe controller.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-11-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Currently, the IRQ device name for both of these IRQs doesn't have Qcom
specific prefix and PCIe domain number. This causes 2 issues:
1. Pollutes the global IRQ namespace since 'global' is a common name.
2. When more than one EP controller instance is present in the SoC, naming
conflict will occur.
Hence, add 'qcom_pcie_ep_' prefix and PCIe domain number suffix to the IRQ
names to uniquely identify the IRQs and also to fix the above mentioned
issues.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-6-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
