- Prevent race between link training and register update via DBI by
inhibiting link training after hot reset and link down (Wilfred Mallawa)
* pci/controller/dw-rockchip:
PCI: dw-rockchip: Delay link training after hot reset in EP mode
Per PCIe r6.0, sec 6.6.1, software must generally wait a minimum of
100ms (PCIE_RESET_CONFIG_WAIT_MS) after Link training completes before
sending a Configuration Request.
Prior to ec9fd499b9 ("PCI: dw-rockchip: Don't wait for link since
we can detect Link Up"), dw-rockchip used dw_pcie_wait_for_link(),
which waited between 0 and 90ms after the link came up before we
enumerate the bus, and this was apparently enough for most devices.
After ec9fd499b9, rockchip_pcie_rc_sys_irq_thread() started
enumeration immediately when handling the link-up IRQ, and devices
(e.g., Laszlo Fiat's PLEXTOR PX-256M8PeGN NVMe SSD) may not be ready
to handle config requests yet.
Delay PCIE_RESET_CONFIG_WAIT_MS after the link-up IRQ before starting
enumeration.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Cc: Laszlo Fiat <laszlo.fiat@proton.me>
Link: https://patch.msgid.link/20250625102347.1205584-12-cassel@kernel.org
RK3588 TRM, section "11.6.1.3.3 Hot Reset and Link-Down Reset" states that:
If you want to delay link re-establishment (after reset) so that you can
reprogram some registers through DBI, you must set app_ltssm_enable =0
immediately after core_rst_n as shown in above. This can be achieved by
enable the app_dly2_en, and end-up the delay by assert app_dly2_done.
I.e. setting app_dly2_en will automatically deassert app_ltssm_enable on
a hot reset, and setting app_dly2_done will re-assert app_ltssm_enable,
re-enabling link training.
When receiving a hot reset/link-down IRQ when running in EP mode, we will
call dw_pcie_ep_linkdown(), which may update registers through DBI. Unless
link training is inhibited, these register updates race with the link
training.
To avoid the race, set PCIE_LTSSM_APP_DLY2_EN so the controller never
automatically trains the link after a link-down or hot reset interrupt.
That way any DBI updates done in the dw_pcie_ep_linkdown() path will happen
while the link is still down. Then allow link training by setting
PCIE_LTSSM_APP_DLY2_DONE
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250613101908.2182053-2-cassel@kernel.org
-----BEGIN PGP SIGNATURE-----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=eWJw
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix and convert the new instance in
dwc/pcie-amd-mdb.c ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-30-jirislaby@kernel.org
PCIe link status check is supposed to return a boolean to indicate whether
the link is up or not. So, modify the link_up callbacks and
dw_pcie_link_up() function to return bool instead of int.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message reword]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250510160710.392122-2-18255117159@163.com
The documentation for the phy_power_off() function explicitly says that it
must be called before phy_exit().
Hence, follow the same rule in rockchip_pcie_phy_deinit().
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
[mani: commit message change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://patch.msgid.link/20250417142138.1377451-1-didi.debian@cknow.org
Some of the callers of rockchip_pcie_link_up() are open coding the
rockchip_pcie_link_up() function, leading to code duplication. So switch
them to use rockchip_pcie_link_up() function.
Also, use the FIELD_GET() macro to simplify the link up check in
rockchip_pcie_link_up().
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250427125316.99627-4-18255117159@163.com
Register definitions were scattered with ambiguous names (e.g.,
PCIE_RDLH_LINK_UP_CHGED in PCIE_CLIENT_INTR_STATUS_MISC) and lacked
hierarchical grouping.
Group registers and their associated bitfields logically. This improves
maintainability and aligns the code with hardware documentation.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250427125316.99627-3-18255117159@163.com
The PCIE_CLIENT_GENERAL_DEBUG register offset is defined but never
used in the driver. It's presence adds noise to the register map.
Remove this unused definition to keep the register list minimal and aligned
with actual hardware usage.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250427125316.99627-2-18255117159@163.com
In the case of PERST# deassert, non-sticky registers will get reset to
their hardware default state and EXT_CAP registers are one among them. But
since the broken ATS cap is hidden only in dw_pcie_ep_ops::pre_init()
callback which is not gettting called during PERST# deassert, it results in
the capability getting advertised again.
So move it to dw_pcie_ep_ops::init() to fix it.
Suggested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/1744594109-209312-1-git-send-email-shawn.lin@rock-chips.com
L0s capability isn't enabled on all Rockchip SoCs by default, so enable it
in order to make ASPM L0s work on Rockchip platforms.
Testing the L0s for a long time revealed that the default N_FTS value of
210 in the hardware doesn't work stable and causes LTSSM to switch between
L0s and Recovery states. This leads to long exit latency and also causes
link down sometimes. So override the value to the max 255, which seems to
work fine under both PHYs used on Rockchip platforms.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/1744850111-236269-2-git-send-email-shawn.lin@rock-chips.com
rockchip_pcie_link_up() currently has two issues:
1. Value 0x11 of PCIE_L0S_ENTRY corresponds to L0 state, not L0S. So the
naming is wrong from the very beginning.
2. Checking for value 0x11 treats other states like L0S and L1 as link
down, which is wrong.
Hence, remove the PCIE_L0S_ENTRY check and also its definition. This allows
adding ASPM support in the successive commits.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/1744850111-236269-1-git-send-email-shawn.lin@rock-chips.com
- Move struct dwc_pcie_vsec_id to include/linux/pcie-dwc.h, where it can be
shared by debugfs, perf, sysfs, etc (Manivannan Sadhasivam)
- Add dw_pcie_find_vsec_capability() to locate Vendor Specific Extended
Capabilities (Shradha Todi)
- Add debugfs-based Silicon Debug, Error Injection, Statistical Counter
support for DWC (Shradha Todi)
- Add debugfs property to expose LTSSM status of DWC PCIe link (Hans Zhang)
- Add Rockchip Vendor ID and Vendor Specific ID of RAS DES Capability so
the DWC debugfs features work for Rockchip as well (Niklas Cassel)
* pci/controller/dwc:
PCI: dw-rockchip: Hide broken ATS capability for RK3588 running in EP mode
PCI: dwc: ep: Add dw_pcie_ep_hide_ext_capability()
PCI: dwc: ep: Return -ENOMEM for allocation failures
PCI: dwc: Add Rockchip to the RAS DES allowed vendor list
PCI: Add Rockchip Vendor ID
PCI: dwc: Add debugfs property to provide LTSSM status of the PCIe link
PCI: dwc: Add debugfs based Statistical Counter support for DWC
PCI: dwc: Add debugfs based Error Injection support for DWC
PCI: dwc: Add debugfs based Silicon Debug support for DWC
PCI: dwc: Add helper to find the Vendor Specific Extended Capability (VSEC)
perf/dwc_pcie: Move common DWC struct definitions to 'pcie-dwc.h'
- Fix endpoint BAR testing so the test can skip disabled BARs instead of
reporting them as failures (Niklas Cassel)
- Verify that pci_endpoint interrupt tests set the correct IRQ type
(Kunihiko Hayashi)
- Fix interpretation of pci_endpoint_test_bars_read_bar() error returns
(Niklas Cassel)
- Fix potential string truncation in pci_endpoint_test_probe() (Niklas
Cassel)
- Increase endpoint test BAR size variable to accommodate BARs larger than
INT_MAX (Niklas Cassel)
- Release IRQs to avoid leak in pci_endpoint interrupt tests (Kunihiko
Hayashi)
- Log the correct IRQ type when pci_endpoint IRQ request test fails
(Kunihiko Hayashi)
- Remove pci_endpoint_test irq_type and no_msi globals; instead use
test->irq_type (Kunihiko Hayashi)
- Remove unnecessary use of managed IRQ functions in pci_endpoint_test
(Kunihiko Hayashi)
- Add and use IRQ_TYPE_* defines in pci_endpoint_test (Niklas Cassel)
- Add struct pci_epc_features.intx_capable and note that RK3568 and RK3588
can't raise INTx interrupts (Niklas Cassel)
- Expose supported IRQ types in CAPS so pci_endpoint_test can set
appropriate type (Niklas Cassel)
- Add PCITEST_IRQ_TYPE_AUTO to pci_endpoint_test for cases where the IRQ
type doesn't matter (Niklas Cassel)
* pci/endpoint-test:
misc: pci_endpoint_test: Add support for PCITEST_IRQ_TYPE_AUTO
PCI: endpoint: pci-epf-test: Expose supported IRQ types in CAPS register
PCI: dw-rockchip: Endpoint mode cannot raise INTx interrupts
PCI: endpoint: Add intx_capable to epc_features struct
selftests: pci_endpoint: Use IRQ_TYPE_* defines from UAPI header
misc: pci_endpoint_test: Use IRQ_TYPE_* defines from UAPI header
PCI: endpoint: pcitest: Add IRQ_TYPE_* defines to UAPI header
misc: pci_endpoint_test: Do not use managed IRQ functions
misc: pci_endpoint_test: Remove global 'irq_type' and 'no_msi'
misc: pci_endpoint_test: Fix 'irq_type' to convey the correct type
misc: pci_endpoint_test: Fix displaying 'irq_type' after 'request_irq' error
misc: pci_endpoint_test: Avoid issue of interrupts remaining after request_irq error
misc: pci_endpoint_test: Handle BAR sizes larger than INT_MAX
misc: pci_endpoint_test: Give disabled BARs a distinct error code
misc: pci_endpoint_test: Fix potential truncation in pci_endpoint_test_probe()
misc: pci_endpoint_test: Fix pci_endpoint_test_bars_read_bar() error handling
selftests: pci_endpoint: Add GET_IRQTYPE checks to each interrupt test
selftests: pci_endpoint: Skip disabled BARs
Neither RK3568 or RK3588 supports INTx interrupts.
Since epc_features is zero initialized, this is strictly not needed.
However, setting intx_capable explicitly to false makes it more clear
that neither RK3568 or RK3588 supports INTx interrupts.
No functional change.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250310111016.859445-14-cassel@kernel.org
When running the RK3588 in Endpoint mode, with an Intel host with IOMMU
enabled, the host side prints:
DMAR: VT-d detected Invalidation Time-out Error: SID 0
When running the RK3588 in Endpoint mode, with an AMD host with IOMMU
enabled, the host side prints:
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01a0]
Rockchip has confirmed that the ATS support for RK3588 only works when
running the PCIe controller in Root Complex (RC) mode, see:
https://lore.kernel.org/linux-pci/93cdce39-1ae6-4939-a3fc-db10be7564e5@rock-chips.com
Usually, to handle these issues, we add a quirk for the PCI vendor and
device ID in drivers/pci/quirks.c with quirk_no_ats(). That is because
we cannot usually modify the capabilities on the EP side. In this case,
we can modify the capabilities on the EP side.
Thus, hide the broken ATS capability on RK3588 when running in EP mode.
That way, we don't need any quirk on the host side, and we see no errors
on the host side, and we can run pci_endpoint_test successfully, with
the IOMMU enabled on the host side.
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: commit log, tidy up code comments and error message]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250310094826.842681-6-cassel@kernel.org
Looking at section "11.4.4.29 USP_PCIE_RESBAR Registers Summary" in the
Technical Reference Manual (TRM) for RK3588, we can see that none of the
BARs are Fixed BARs, but actually Resizable BARs.
I couldn't find any reference in the TRM for RK3568, but looking at the
downstream PCIe endpoint driver, both RK3568 and RK3588 are treated as
the same, so the BARs on RK3568 must also be Resizable BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-16-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The Root Complex specific device tree binding for pcie-dw-rockchip has the
'sys' interrupt marked as required.
The driver requests the 'sys' IRQ unconditionally, and errors out if not
provided.
Thus, we can unconditionally set 'use_linkup_irq', so dw_pcie_host_init()
doesn't wait for the link to come up.
This will skip the wait for link up (since the bus will be enumerated once
the link up IRQ is triggered), which reduces the bootup time.
Link: https://lore.kernel.org/r/20250113-rockchip-no-wait-v1-1-25417f37b92f@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Most boards using the pcie-dw-rockchip PCIe controller lack standard
hotplug support.
Thus, when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. This can be avoided by using the
'dll_link_up' interrupt in the combined system interrupt 'sys'.
Once the 'dll_link_up' IRQ is received, the bus underneath the host bridge
is scanned to enumerate PCIe endpoint devices.
This implements the same functionality that was implemented in the DWC
based pcie-qcom driver in 4581403f67 ("PCI: qcom: Enumerate endpoints
based on Link up event in 'global_irq' interrupt").
The Root Complex specific device tree binding for pcie-dw-rockchip already
has the 'sys' interrupt marked as required, so there is no need to update
the device tree binding. This also means that we can request the 'sys' IRQ
unconditionally.
Link: https://lore.kernel.org/r/20241127145041.3531400-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, squash Pei Xiao's redundant dev_err() fix from
https://lore.kernel.org/r/327718207d3cd72847c079ff9d56eb246744c182.1736126067.git.xiaopei01@kylinos.cn,
squash Niklas's #define change from https://lore.kernel.org/r/20250103095812.2408364-2-cassel@kernel.org]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A previous commit ("PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper")
removed the dw_pcie_ep_init_notify() wrapper and changed the DWC glue
drivers to instead use pci_epc_init_notify() directly.
The endpoint support for the dw-rockchip had not been merged at that point
in time, so the previous commit wrapper") did not update dw-rockchip.
Do the same change for dw-rockchip, so that the driver will not try
to use a function that has now been removed.
Link: https://lore.kernel.org/linux-pci/20240622132024.2927799-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in rk3568 and rk3588 can operate in endpoint mode.
This endpoint mode support heavily leverages the existing code in
pcie-designware-ep.c.
Add support for endpoint mode to the existing pcie-dw-rockchip glue
driver.
[kwilczynski: squash with patch adding the PCI_ENDPOINT dependency]
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-10-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the driver to prepare for EP mode.
Add of-match data to the existing compatible, and explicitly define it as
DW_PCIE_RC_TYPE. This way, we will be able to add EP mode in a follow-up
commit in a much less intrusive way, which makes the follow-up commit much
easier to review.
No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-9-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add a rockchip_pcie_ltssm() helper function that reads the LTSSM status.
This helper will be used in additional places in follow-up commits.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-8-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fix the indentation of rockchip_pcie_{readl,writel}_apb() parameters to
match the opening parenthesis.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-7-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
Drivers that silently fail to probe provide a bad user experience and
make it unnecessarily hard to debug such a failure.
Fix it by using dev_err_probe() instead of a plain return.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240227141256.413055-2-ukleinek@debian.org
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more explicit and match spec
terminology (Bjorn Helgaas)
- Use existing PCI_IRQ_INTX, PCI_IRQ_MSI, PCI_IRQ_MSIX in artpec6, cadence,
designware, designware-plat, dra7xx, imx6, keembay, keystone, layerscape,
mhi, ntb, qcom, rcar, rcar-gen4, rockchip, tegra194, uniphier, vntb; drop
the redundant pci_epc_irq_type enum with the same values (Damien Le Moal)
- Use "intx" instead of "leg" or "legacy" when describing INTx interrupts
in endpoint core, endpoint tests, cadence, dra7xx, designware,
dw-rockchip, dwc core, imx6, keystone, layerscape, qcom, rcar-gen4,
rockchip, tegra194, uniphier, xilinx-nwl (Damien Le Moal)
* pci/irq-clean-up:
PCI: xilinx-nwl: Use INTX instead of legacy
PCI: rockchip-host: Rename rockchip_pcie_legacy_int_handler()
PCI: rockchip-ep: Use INTX instead of legacy
PCI: uniphier: Use INTX instead of legacy
PCI: tegra194: Use INTX instead of legacy
PCI: dw-rockchip: Rename rockchip_pcie_legacy_int_handler()
PCI: keystone: Use INTX instead of legacy
PCI: dwc: Rename dw_pcie_ep_raise_legacy_irq()
PCI: cadence: Use INTX instead of legacy
PCI: dra7xx: Rename dra7xx_pcie_raise_legacy_irq()
misc: pci_endpoint_test: Use INTX instead of LEGACY
PCI: endpoint: Rename LEGACY to INTX in test function driver
PCI: endpoint: Use INTX instead of legacy
PCI: endpoint: Drop PCI_EPC_IRQ_XXX definitions
PCI: Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX
Since the name of the dw_pcie_host_ops struct makes it obvious that it's
for the PCIe Host, drop the host prefix from the struct members.
[kwilczynski: commit log]
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231220053829.1921187-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Lei Chuanhua <lchuanhua@maxlinear.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Rename the function rockchip_pcie_legacy_int_handler() to
rockchip_pcie_intx_handler() to match the code managing INTX interrupts
(e.g. intx_domain_ops) and the term used in the PCI specifications.
Link: https://lore.kernel.org/r/20231122060406.14695-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus. As
part of that merge prepping Arm DT support 13 years ago, they "temporarily"
include each other. They also include platform_device.h and of.h. As a
result, there's a pretty much random mix of those include files used
throughout the tree. In order to detangle these headers and replace the
implicit includes with struct declarations, users need to explicitly
include the correct includes.
Link: https://lore.kernel.org/r/20230714174827.4061572-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All of the DW PCIe core driver entities except the pcie_port struct have
names with the "dw_" prefix to distinguish local and common PCIe name
spaces, and endpoint-related entities have an "_ep" suffix.
Rename struct pcie_port to dw_pcie_rp to make it more consistent with other
names.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
The legacy interrupts on the rk356x PCIe controller are handled by a
single muxed interrupt. Add IRQ domain support to the pcie-dw-rockchip
driver to support the virtual domain.
Link: https://lore.kernel.org/r/20220429123832.2376381-4-pgwipeout@gmail.com
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
The PCIe controller is in an unknown state at driver probe. This can
lead to undesireable effects when the driver attempts to configure the
controller.
Prevent issues in the future by resetting the core during probe.
Link: https://lore.kernel.org/r/20220429123832.2376381-3-pgwipeout@gmail.com
Tested-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add a driver for the DesignWare-based PCIe controller found on
RK356X. The existing pcie-rockchip-host driver is only used for
the Rockchip-designed IP found on RK3399.
Link: https://lore.kernel.org/r/20210625065511.1096935-1-xxm@rock-chips.com
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
