- Export DWC MSI controller related APIs for use by upcoming DWC-based ECAM
implementation (Mayank Rana)
- Rename gen_pci_init() to pci_host_common_ecam_create() and export for use
by controller drivers (Mayank Rana)
- Add DT binding and driver support for SA8255p, which supports ECAM for
Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port resets in
a Root Port stanza and deprecate describing them in the host bridge; this
makes it possible to support multiple Root Ports in the future (Krishna
Chaitanya Chundru)
* pci/controller/qcom:
PCI: qcom: Add support for parsing the new Root Port binding
dt-bindings: PCI: qcom: Move PHY & reset GPIO to Root Port node
PCI: qcom: Add support for Qualcomm SA8255p based PCIe Root Complex
dt-bindings: PCI: qcom,pcie-sa8255p: Document ECAM compliant PCIe root complex
PCI: host-generic: Rename and export gen_pci_init() for PCIe controller drivers
PCI: dwc: Export DWC MSI controller related APIs
- Add IMX8MQ_EP third 64-bit BAR in epc_features (Richard Zhu)
- Add IMX8MM_EP and IMX8MP_EP fixed 256-byte BAR 4 in epc_features (Richard
Zhu)
- Factor imx_pcie_add_lut_by_rid() out of imx_pcie_enable_device() for use
by LUT configuration (Frank Li)
- Configure LUT for MSI/IOMMU in Endpoint mode so Root Complex can trigger
doorbel on Endpoint (Frank Li)
- Remove apps_reset (LTSSM_EN) from imx_pcie_{assert,deassert}_core_reset(),
which fixes a hotplug regression on i.MX8MM (Richard Zhu)
- Delay Endpoint link start until configfs 'start' written (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Delay link start until configfs 'start' written
PCI: imx6: Remove apps_reset toggling from imx_pcie_{assert/deassert}_core_reset
PCI: imx6: Add LUT configuration for MSI/IOMMU in Endpoint mode
PCI: imx6: Add helper function imx_pcie_add_lut_by_rid()
PCI: imx6: Add IMX8MM_EP and IMX8MP_EP fixed 256-byte BAR 4 in epc_features
PCI: imx6: Add IMX8MQ_EP third 64-bit BAR in epc_features
- Prevent race between link training and register update via DBI by
inhibiting link training after hot reset and link down (Wilfred Mallawa)
* pci/controller/dw-rockchip:
PCI: dw-rockchip: Delay link training after hot reset in EP mode
- Rename PCIE_RESET_CONFIG_DEVICE_WAIT_MS to PCIE_RESET_CONFIG_WAIT_MS (the
required delay before sending config requests after a reset) (Niklas
Cassel)
- PCIE_T_RRS_READY_MS and PCIE_RESET_CONFIG_WAIT_MS were two names for the
same delay; replace PCIE_T_RRS_READY_MS with PCIE_RESET_CONFIG_WAIT_MS
and remove PCIE_T_RRS_READY_MS (Niklas Cassel)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ to
dw-rockchip, qcom (Niklas Cassel)
- Add required PCIE_RESET_CONFIG_WAIT_MS after waiting for Link up on
Ports that support > 5.0 GT/s in dwc core (Niklas Cassel)
- Move LINK_WAIT_SLEEP_MS and LINK_WAIT_MAX_RETRIES to pci.h and prefix
with 'PCIE_' for potential sharing across drivers (Niklas Cassel)
* pci/controller/linkup-fix:
PCI: Move link up wait time and max retries macros to pci.h
PCI: dwc: Ensure that dw_pcie_wait_for_link() waits 100 ms after link up
PCI: qcom: Wait PCIE_RESET_CONFIG_WAIT_MS after link-up IRQ
PCI: dw-rockchip: Wait PCIE_RESET_CONFIG_WAIT_MS after link-up IRQ
PCI: rockchip-host: Use macro PCIE_RESET_CONFIG_WAIT_MS
PCI: Rename PCIE_RESET_CONFIG_DEVICE_WAIT_MS to PCIE_RESET_CONFIG_WAIT_MS
Add driver support for DesignWare based PCIe controller in SG2044 SoC. The
driver currently supports the Root Complex mode.
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
[mani: renamed the driver to 'pcie-sophgo.c' and Kconfig fix]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: whitespace]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250504004420.202685-3-inochiama@gmail.com
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/04d4a96046490e50139826c16423954e033cdf89.1750858083.git.namcao@linutronix.de
All irq_domain functions now accept fwnode instead of of_node. But many
PCI controllers still extract dev to of_node and then of_node to fwnode.
Instead, clean this up and simply use the dev_fwnode() helper to extract
fwnode directly from dev. Internally, it still does dev => of_node =>
fwnode steps, but it's now hidden from the users.
In the case of altera, this also removes an unused 'node' variable that is
only used when CONFIG_OF is enabled:
drivers/pci/controller/pcie-altera.c: In function 'altera_pcie_init_irq_domain':
drivers/pci/controller/pcie-altera.c:855:29: error: unused variable 'node' [-Werror=unused-variable]
855 | struct device_node *node = dev->of_node;
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de> # altera
[bhelgaas: squash together, rebase to precede msi-parent]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250521163329.2137973-1-arnd@kernel.org
Link: https://patch.msgid.link/20250611104348.192092-16-jirislaby@kernel.org
Link: https://patch.msgid.link/20250723065907.1841758-1-jirislaby@kernel.org
According to Documentation/PCI/endpoint/pci-endpoint-cfs.rst, the Endpoint
controller (EPC) should only start the link when userspace writes '1' to
the '/sys/kernel/config/pci_ep/controllers/<EPC>/start' attribute, which
ultimately results in calling imx_pcie_start_link() via
pci_epc_start_store().
To align with the documented behavior, do not start the link automatically
when adding the EP controller.
Fixes: 75c2f26da0 ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250709033722.2924372-3-hongxing.zhu@nxp.com
apps_reset corresponds to LTSSM_EN in i.MX7, i.MX8MQ, i.MX8MM and i.MX8MP
platforms. Since assertion/de-assertion of apps_reset is done in
imx_pcie_ltssm_enable() and imx_pcie_ltssm_disable(), remove it from
imx_pcie_assert_core_reset() and imx_pcie_deassert_core_reset().
This also fixes a failure in enumerating the PI7C9X2G608GP (hotplug) chip
reliably on i.MX8MM, as reported by Tim.
It should be noted that only i.MX7D, i.MX8MQ, i.MX8MM, and i.MX8MP
platforms have the apps_reset logic, so this change doesn't have any effect
on other platforms.
Fixes: ef61c7d8d0 ("PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()")
Reported-by: Tim Harvey <tharvey@gateworks.com>
Closes: https://lore.kernel.org/all/CAJ+vNU3ohR2YKTwC4xoYrc1z-neDoH2TTZcMHDy+poj9=jSy+w@mail.gmail.com/
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mp-venice-gw74xx (i.MX8MP + hotplug capable switch)
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250709033722.2924372-2-hongxing.zhu@nxp.com
Add LUT entry for MSI/IOMMU in Endpoint mode by calling
imx_pcie_add_lut_by_rid() helper function. Since only one physical function
is supported in the Endpoint mode for now, '0' is passed as the Device ID.
This sets up a single LUT entry required for MSI/IOMMU.
The Endpoint function can operate without LUT configuration if neither
IOMMU nor MSI is used by the platform. This LUT configuration is used for
the EP doorbell feature by allowing the Root Complex to trigger the
doorbell on the Endpoint with the help of the Endpoint MSI controller.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[mani: reworded the comments & commit message and dropped tested-by tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250710-ep-msi-v21-2-57683fc7fb25@nxp.com
Add helper function imx_pcie_add_lut_by_rid(), which will be used by the
upcoming LUT configuration for MSI/IOMMU in the Endpoint mode. No
functional change.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[mani: reworded commit message and dropped tested-by tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250710-ep-msi-v21-1-57683fc7fb25@nxp.com
The DT binding has moved the PHY, PERST# properties to Root Port node from
the Host Bridge node. So add support for parsing the new binding. The new
binding uses 'reset-gpios' property for PERST#, hence parse the same
property in the driver instead of the legacy 'perst-gpios'.
To maintain DT backwards compatibility, fallback to the legacy method of
parsing the host bridge node if the properties are not present in the Root
Port node.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: refactored the root port parsing code, fixed a bug & commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250702-perst-v5-2-920b3d1f6ee1@qti.qualcomm.com
For IMX8MM_EP and IMX8MP_EP, add fixed 256-byte BAR 4 and reserved BAR 5
in imx8m_pcie_epc_features.
Fixes: 75c2f26da0 ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[bhelgaas: add details in subject]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250708091003.2582846-3-hongxing.zhu@nxp.com
Export dw_pcie_msi_host_init(), dw_pcie_msi_init(), and dw_pcie_free_msi()
APIs to allow them to be reused by the upcoming DWC based ECAM driver
implementation. Also, move MSI IRQ related initialization code to
dw_pcie_msi_init(), as this code must be executed before dw_pcie_msi_init()
API can be used with ECAM driver.
Signed-off-by: Mayank Rana <mayank.rana@oss.qualcomm.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250616224259.3549811-2-mayank.rana@oss.qualcomm.com
Move the LINK_WAIT_SLEEP_MS and LINK_WAIT_MAX_RETRIES macros to pci.h.
Prefix the macros with PCIE_ in order to avoid redefining these for
drivers that already have macros named like this.
No functional changes.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250625102347.1205584-15-cassel@kernel.org
As per PCIe r6.0, sec 6.6.1, a Downstream Port that supports Link speeds
greater than 5.0 GT/s, software must wait a minimum of 100 ms after Link
training completes before sending a Configuration Request.
Add this delay in dw_pcie_wait_for_link(), after the link is reported as
up. The delay will only be performed in the success case where the link
came up.
DWC glue drivers that have a link up IRQ (drivers that set
use_linkup_irq = true) do not call dw_pcie_wait_for_link(), instead they
perform this delay in their threaded link up IRQ handler.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Link: https://patch.msgid.link/20250625102347.1205584-14-cassel@kernel.org
Per PCIe r6.0, sec 6.6.1, software must generally wait a minimum of
100ms (PCIE_RESET_CONFIG_WAIT_MS) after Link training completes before
sending a Configuration Request.
Prior to 36971d6c5a ("PCI: qcom: Don't wait for link if we can detect
Link Up"), qcom used dw_pcie_wait_for_link(), which waited between 0
and 90ms after the link came up before we enumerate the bus, and this
was apparently enough for most devices.
After 36971d6c5a, qcom_pcie_global_irq_thread() started enumeration
immediately when handling the link-up IRQ, and devices (e.g., Laszlo
Fiat's PLEXTOR PX-256M8PeGN NVMe SSD) may not be ready to handle config
requests yet.
Delay PCIE_RESET_CONFIG_WAIT_MS after the link-up IRQ before starting
enumeration.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Link: https://patch.msgid.link/20250625102347.1205584-13-cassel@kernel.org
Per PCIe r6.0, sec 6.6.1, software must generally wait a minimum of
100ms (PCIE_RESET_CONFIG_WAIT_MS) after Link training completes before
sending a Configuration Request.
Prior to ec9fd499b9 ("PCI: dw-rockchip: Don't wait for link since
we can detect Link Up"), dw-rockchip used dw_pcie_wait_for_link(),
which waited between 0 and 90ms after the link came up before we
enumerate the bus, and this was apparently enough for most devices.
After ec9fd499b9, rockchip_pcie_rc_sys_irq_thread() started
enumeration immediately when handling the link-up IRQ, and devices
(e.g., Laszlo Fiat's PLEXTOR PX-256M8PeGN NVMe SSD) may not be ready
to handle config requests yet.
Delay PCIE_RESET_CONFIG_WAIT_MS after the link-up IRQ before starting
enumeration.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Cc: Laszlo Fiat <laszlo.fiat@proton.me>
Link: https://patch.msgid.link/20250625102347.1205584-12-cassel@kernel.org
RK3588 TRM, section "11.6.1.3.3 Hot Reset and Link-Down Reset" states that:
If you want to delay link re-establishment (after reset) so that you can
reprogram some registers through DBI, you must set app_ltssm_enable =0
immediately after core_rst_n as shown in above. This can be achieved by
enable the app_dly2_en, and end-up the delay by assert app_dly2_done.
I.e. setting app_dly2_en will automatically deassert app_ltssm_enable on
a hot reset, and setting app_dly2_done will re-assert app_ltssm_enable,
re-enabling link training.
When receiving a hot reset/link-down IRQ when running in EP mode, we will
call dw_pcie_ep_linkdown(), which may update registers through DBI. Unless
link training is inhibited, these register updates race with the link
training.
To avoid the race, set PCIE_LTSSM_APP_DLY2_EN so the controller never
automatically trains the link after a link-down or hot reset interrupt.
That way any DBI updates done in the dw_pcie_ep_linkdown() path will happen
while the link is still down. Then allow link training by setting
PCIE_LTSSM_APP_DLY2_DONE
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250613101908.2182053-2-cassel@kernel.org
-----BEGIN PGP SIGNATURE-----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=eWJw
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
- Create debugfs directory for 'aspm_state_cnt' only when CONFIG_PCIEASPM
is enabled, since there are no other entries (Hans Zhang)
* pci/controller/tegra194:
PCI: tegra194: Create debugfs directory only when CONFIG_PCIEASPM is enabled
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
* pci/controller/rcar-gen4:
PCI: rcar-gen4: Document how to obtain platform firmware
PCI: rcar-gen4: set ep BAR4 fixed size
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT lacks
'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for 8, 32,
and 64 GT/s lane equalization registers (Krishna Chaitanya Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
* pci/controller/qcom:
PCI: qcom: Add support for IPQ5018
dt-bindings: PCI: qcom: Add IPQ5018 SoC
PCI: dwc: Add support for configuring lane equalization presets
PCI: Add lane equalization register offsets
PCI: dwc: Update pci->num_lanes to maximum supported link width
PCI: of: Add of_pci_get_equalization_presets() API
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP (Richard
Zhu)
- Remove redundant dw_pcie_wait_for_link() from imx_pcie_start_link();
since the DWC core does this, imx6 only needs it when retraining for a
faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in some
cases, the controller can't exit 'L23 Ready' through Beacon or PERST#
deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8 GT/s,
causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Save and restore the LUT setting during suspend/resume for i.MX95 SoC
PCI: imx6: Add PLL lock check for i.MX95 SoC
PCI: imx6: Add workaround for errata ERR051586
PCI: imx6: Add workaround for errata ERR051624
PCI: imx6: Toggle the core reset for i.MX95 PCIe
PCI: imx6: Call dw_pcie_wait_for_link() from start_link() callback only when required
PCI: imx6: Skip link up workaround for newer platforms
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training more
robust; this will not affect the intended link width if all lanes are
functional (Wenbin Yao)
* pci/controller/dwc:
PCI: dwc: Make link training more robust by setting PORT_LOGIC_LINK_WIDTH to one lane
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the link
is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s for Root
Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead of
rockchip_pcie_ep_pre_init() so it stays hidden after PERST# resets
non-sticky registers (Shawn Lin)
- Remove unused PCIE_CLIENT_GENERAL_DEBUG definition (Hans Zhang)
- Organize register and bitfield definitions logically (Hans Zhang)
- Use rockchip_pcie_link_up() to check link up instead of open coding, and
use GENMASK() and FIELD_GET() when possible (Hans Zhang)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up() and
armada8k, dra7xx, dw-rockchip, exynos, histb, keembay, keystone, kirin,
meson, qcom, qcom-ep, rcar_gen4, spear13xx, tegra194, uniphier, visconti
(Hans Zhang)
- Return bool (not int) for link-up check in mobiveil_pab_ops.link_up() and
layerscape-gen4, mobiveil (Hans Zhang)
- Simplify j721e link-up check (Hans Zhang)
- Convert pci-host-common to a library so platforms that don't need native
host controller drivers don't need to include these helper functions
(Manivannan Sadhasivam)
* pci/controller/dw-rockchip:
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI: cadence: Simplify J721e link status check
PCI: mobiveil: Return bool from link up check
PCI: dwc: Return bool from link up check
PCI: dw-rockchip: Fix PHY function call sequence in rockchip_pcie_phy_deinit()
PCI: dw-rockchip: Use rockchip_pcie_link_up() to check link up instead of open coding
PCI: dw-rockchip: Reorganize register and bitfield definitions
PCI: dw-rockchip: Remove unused PCIE_CLIENT_GENERAL_DEBUG definition
PCI: dw-rockchip: Move rockchip_pcie_ep_hide_broken_ats_cap_rk3588() to dw_pcie_ep_ops::init()
PCI: dw-rockchip: Enable ASPM L0s capability for both RC and EP modes
PCI: dw-rockchip: Remove PCIE_L0S_ENTRY check from rockchip_pcie_link_up()
# Conflicts:
# drivers/pci/controller/pcie-apple.c
# include/linux/pci-ecam.h
- For fixed-size BARs, retain both the actual size and the possibly larger
size allocated to accommodate iATU alignment requirements (Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space than
needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence endpoint
controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
* pci/endpoint:
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
PCI: dwc: ep: Correct PBA offset in .set_msix() callback
PCI: endpoint: pci-epf-vntb: Simplify ctrl/SPAD space allocation
PCI: endpoint: Retain fixed-size BAR size as well as aligned size
This common library will be used as a placeholder for helper functions
shared by the host controller drivers. This avoids placing the host
controller drivers specific helpers in drivers/pci/*.c, to avoid enlarging
the kernel image on platforms that do not use host controller drivers at
all (like x86/ACPI platforms).
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250508-pcie-reset-slot-v4-3-7050093e2b50@linaro.org
The kdoc for pci_epc_set_msix() says:
"Invoke to set the required number of MSI-X interrupts."
The kdoc for the callback pci_epc_ops->set_msix() says:
"ops to set the requested number of MSI-X interrupts in the MSI-X
capability register"
pci_epc_ops::set_msix() does however expect the parameter 'interrupts' to
be in the encoding as defined by the Table Size field. Nowhere in the
kdoc does it say that the number of interrupts should be in Table Size
encoding.
It is very confusing that the API pci_epc_set_msix() and the callback
function pci_epc_ops::set_msix() both take a parameter named 'interrupts',
but they expect completely different encodings.
Clean up the API and the callback function to have the same semantics,
i.e. the parameter represents the number of interrupts, regardless of the
internal encoding of that value.
Also rename the parameter 'interrupts' to 'nr_irqs', in both the wrapper
function and the callback function, such that the name is unambiguous.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-14-cassel@kernel.org
The kdoc for pci_epc_set_msi() says:
"Invoke to set the required number of MSI interrupts."
The kdoc for the callback pci_epc_ops::set_msi() says:
"ops to set the requested number of MSI interrupts in the MSI capability
register"
pci_epc_ops::set_msi() does however expect the parameter 'interrupts' to be
in the encoding as defined by the Multiple Message Capable (MMC) field of
the MSI capability structure. Nowhere in the kdoc does it say that the
number of interrupts should be in MMC encoding.
It is very confusing that the API pci_epc_set_msi() and the callback
function pci_epc_ops::set_msi() both take a parameter named 'interrupts',
but they expect completely different encodings.
Clean up the API and the callback function to have the same semantics,
i.e. the parameter represents the number of interrupts, regardless of the
internal encoding of that value.
Also rename the parameter 'interrupts' to 'nr_irqs', in both the wrapper
function and the callback function, such that the name is unambiguous.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-13-cassel@kernel.org
The kdoc for pci_epc_get_msix() says:
"Invoke to get the number of MSI-X interrupts allocated by the RC"
The kdoc for the callback pci_epc_ops->get_msix() says:
"ops to get the number of MSI-X interrupts allocated by the RC from the
MSI-X capability register"
pci_epc_ops::get_msix() does however return the number of interrupts in the
encoding as defined by the Table Size field. Nowhere in the kdoc does it
say that the returned number of interrupts is in Table Size encoding.
It is very confusing that the API pci_epc_get_msix() and the callback
function pci_epc_ops::get_msix() don't return the same value.
Clean up the API and the callback function to have the same semantics,
i.e. return the number of interrupts, regardless of the internal encoding
of that value.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-12-cassel@kernel.org
The kdoc for API pci_epc_get_msi() says:
"Invoke to get the number of MSI interrupts allocated by the RC"
The kdoc for the callback pci_epc_ops::get_msi() says:
"ops to get the number of MSI interrupts allocated by the RC from
the MSI capability register"
pci_epc_ops::get_msi() does however return the number of interrupts in the
encoding as defined by the Multiple Message Enable (MME) field of the MSI
Capability structure.
Nowhere in the kdoc does it say that the returned number of interrupts is
in MME encoding. It is very confusing that the API pci_epc_get_msi() and
the callback function pci_epc_ops::get_msi() don't return the same value.
Clean up the API and the callback function to have the same semantics,
i.e. return the number of interrupts, regardless of the internal encoding
of that value.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-11-cassel@kernel.org
While dw_pcie_ep_set_msix() writes the Table Size field correctly (N-1),
the calculation of the PBA offset is wrong because it calculates space for
(N-1) entries instead of N.
This results in the following QEMU error when using PCI passthrough on a
device which relies on the PCI endpoint subsystem:
failed to add PCI capability 0x11[0x50]@0xb0: table & pba overlap, or they don't fit in BARs, or don't align
Fix the calculation of PBA offset in the MSI-X capability.
[bhelgaas: more specific subject and commit log]
Fixes: 83153d9f36 ("PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250514074313.283156-9-cassel@kernel.org
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix and convert the new instance in
dwc/pcie-amd-mdb.c ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-30-jirislaby@kernel.org
When PTM is enabled, PTM_UPDATING interrupt will be fired for each PTM
context update, which will be once every 10ms in the case of auto context
update. Since the interrupt is not strictly needed for making use of PTM,
mask it to avoid the overhead of processing it.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-4-02d26d51400b@linaro.org
Synopsys Designware PCIe IPs support PTM capability as defined in the PCIe
spec r6.0, sec 6.21. The PTM context information is exposed through Vendor
Specific Extended Capability (VSEC) registers on supported controller
implementation.
Hence, add support for exposing these context information to userspace
through the debugfs interface for the DWC controllers (both RC and EP).
Currently, only Qcom controllers are supported. For adding support for
other DWC vendor controllers, dwc_pcie_ptm_vsec_ids[] needs to be extended.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-3-02d26d51400b@linaro.org
Upcoming PTM debugfs interface relies on the DWC PCIe mode to expose the
relevant debugfs attributes to userspace. So pass the mode to
dwc_pcie_debugfs_init() API from host and ep drivers and save it in
'struct dw_pcie::mode'.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-2-02d26d51400b@linaro.org
PCIe link status check is supposed to return a boolean to indicate whether
the link is up or not. So, modify the link_up callbacks and
dw_pcie_link_up() function to return bool instead of int.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message reword]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250510160710.392122-2-18255117159@163.com
