Preparatory patch in order to reuse nvme_multi_css in the nvme target
code.
Signed-off-by: Adam Manzanares <a.manzanares@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When triggering a rescan due to a namespace resize we will be
receiving AENs on every controller, triggering a rescan of all
attached namespaces. If multipath is active only the current path and
the ns_head disk will be updated, the other paths will still refer to
the old size until AENs for the remaining controllers are received.
If I/O comes in before that it might be routed to one of the old
paths, triggering an I/O failure with 'access beyond end of device'.
With this patch the old paths are skipped from multipath path
selection until the controller serving these paths has been rescanned.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[dwagner: - introduce NVME_NS_READY flag instead of NVME_NS_INVALIDATE
- use 'revalidate' instead of 'invalidate' which
follows the zoned device code path.
- clear NVME_NS_READY before clearing current_path]
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
These values are unused now that the lightnvm support is gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Now that the lightnvm driver is removed, we don't need a pointer to it's
now non-existent struct.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We cannot detect a (perhaps buggy) controller that is sending us
a completion for a request that was already completed (for example
sending a completion twice), this phenomenon was seen in the wild
a few times.
So to protect against this, we use the upper 4 msbits of the nvme sqe
command_id to use as a 4-bit generation counter and verify it matches
the existing request generation that is incrementing on every execution.
The 16-bit command_id structure now is constructed by:
| xxxx | xxxxxxxxxxxx |
gen request tag
This means that we are giving up some possible queue depth as 12 bits
allow for a maximum queue depth of 4095 instead of 65536, however we
never create such long queues anyways so no real harm done.
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Lightnvm supports the OCSSD 1.x and 2.0 specs which were early attempts
to produce Open Channel SSDs and never made it into the NVMe spec
proper. They have since been superceeded by NVMe enhancements such
as ZNS support. Remove the support per the deprecation schedule.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210812132308.38486-1-hch@lst.de
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When the last path to a ns_head drops the current code
removes the ns_head from the subsystem list, but will only
delete the disk itself if the last reference to the ns_head
drops. This is causing an refcounting imbalance eg when
applications have a reference to the disk, as then they'll
never get notified that the disk is in fact dead.
This patch moves the call 'del_gendisk' into nvme_mpath_check_last_path(),
ensuring that the disk can be properly removed and applications get the
appropriate notifications.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We don't have an nvme status to report if the driver's .queue_rq()
returns an error without dispatching the requested nvme command. Check
the return value from blk_execute_rq() for all passthrough commands so
the caller may know their command was not successful.
If the command is from the target passthrough interface and fails to
dispatch, synthesize the response back to the host as a internal target
error.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210610214437.641245-5-kbusch@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The generic blk_execute_rq() knows how to handle polled completions. Use
that instead of implementing an nvme specific handler.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210610214437.641245-3-kbusch@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For various transports such as fc/tcp/pci it is common to check if
NVMe SGLs are supported or not by the controller.
In this preparation patch we add a helper to avoid the open coding of
such checks in the various transport.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that only one caller is left remove the helpers by restructuring
nvme_pr_command so that it has two helpers for sending a command of to a
given nsid using either the ns_head for multipath, or the namespace
stored in the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Split multipath support out of nvme_report_zones into a separate helper
and simplify the non-multipath version as a result.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
nvme_init_identify and thus nvme_mpath_init can be called multiple
times and thus must not overwrite potentially initialized or in-use
fields. Split out a helper for the basic initialization when the
controller is initialized and make sure the init_identify path does
not blindly change in-use data structures.
Fixes: 0d0b660f21 ("nvme: add ANA support")
Reported-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
queue_rq() in pci only checks if the dispatched queue (nvmeq) is ready,
e.g. not being suspended. Since nvme_alloc_admin_tags() in reset flow
restarts the admin queue, users are able to submit admin commands to a
controller before reset_work() completes. Commands submitted under this
condition may interfere with commands that performs identify, IO queue
setup in reset_work(), and may result in a hang described in the
following patch.
As seen in the fabrics, user commands are prevented from being executed
under inproper controller states. We may reuse this logic to maintain a
clear admin queue during reset_work().
Signed-off-by: Tao Chiu <taochiu@synology.com>
Signed-off-by: Cody Wong <codywong@synology.com>
Reviewed-by: Leon Chien <leonchien@synology.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In multipath case, we should consider namespace attachment with
controllers in a subsystem when we find out the live controller for the
namespace. This patch manually reverted the commit 3557a44097
("nvme: don't bother to look up a namespace for controller ioctls") with
few more updates to nvme_ns_head_chr_ioctl which has been newly updated.
Fixes: 3557a44097 ("nvme: don't bother to look up a namespace for
controller ioctls")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Userspace has not been allowed to I/O to device that's failed to
be initialized. This patch introduces generic per-namespace character
device to allow userspace to I/O regardless the block device is there or
not.
The chardev naming convention will similar to the existing blkdev naming,
using a ng prefix instead of nvme, i.e.
- /dev/ngXnY
It also supports multipath which means it will not expose chardev for the
hidden namespace blkdevs (e.g., nvmeXcYnZ). If /dev/ngXnY is created for
a ns_head, then I/O request will be routed to a specific controller
selected by the iopolicy of the subsystem.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Tested-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
According to the NVMe base spec the KATO commands should be sent
at half of the KATO interval, to properly account for round-trip
times.
As we now will only ever send one KATO command per connection we
can easily use the recommended values.
This also fixes a potential issue where the request timeout for
the KATO command does not match the value in the connect command,
which might be causing spurious connection drops from the target.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move the multipath block_device_operations to multipath.c, where they
belong.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Split out the ioctl code from core.c into a new file. Also update
copyrights while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Pass the proper user pointer instead of the not all that useful integer
representation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Return false from nvme_set_disk_name and let the caller set the
non-multipath name instead of duplicating the naming information in two
places. Also remove the pointless local variables for the disk name
and flags and the not needed ctrl argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Move the multipath gendisk out of #ifdef CONFIG_NVME_MULTIPATH and add
a new nvme_ns_head_multipath that uses it to check if a ns_head has
a multipath device associated with it.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[hch: added the IS_ENABLED, converted a few existing users]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Commands that access LBA contents without a data transfer between the
host historically have not had a spec defined upper limit. The driver
set the queue constraints for such commands to the max data transfer
size just to be safe, but this artificial constraint frequently limits
devices below their capabilities.
The NVMe Workgroup ratified TP4040 defines how a controller may
advertise their non-MDTS limits. Use these if provided and default to
the current constraints if not. Since the Dataset Management command
limits are defined in logical blocks, but without a namespace to tell us
the logical block size, the code defaults to the safe 512b size.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
All nvme transport drivers preallocate an nvme command for each request.
Assume to use that command for nvme_setup_cmd() instead of requiring
drivers pass a pointer to it. All nvme drivers must initialize the
generic nvme_request 'cmd' to point to the transport's preallocated
nvme_command.
The generic nvme_request cmd pointer had previously been used only as a
temporary copy for passthrough commands. Since it now points to the
command that gets dispatched, passthrough commands must directly set it
up prior to executing the request.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is a prep patch so that we can move the identify data structure
related code initialization from nvme_init_identify() into a helper.
Rename the function nvmet_init_identify() to nvmet_init_ctrl_finish().
Next patch will move the nvme_id_ctrl related initialization from newly
renamed function nvme_init_ctrl_finish() into the nvme_init_identify()
helper.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the proper macro instead of hard-coded value.
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some Amazon NVMe controllers do not follow the NVMe specification
and are limited to 48-bit DMA addresses. Add a quirk to force
bounce buffering if needed and limit the IOVA allocation for these
devices.
This affects all current Amazon NVMe controllers that expose EBS
volumes (0x0061, 0x0065, 0x8061) and local instance storage
(0xcd00, 0xcd01, 0xcd02).
Signed-off-by: Filippo Sironi <sironi@amazon.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The original design to use device-managed resource allocation
doesn't really work as the NVMe controller has a vastly different
lifetime than the hwmon sysfs attributes, causing warning about
duplicate sysfs entries upon reconnection.
This patch reworks the hwmon allocation to avoid device-managed
resource allocation, and uses the NVMe controller as parent for
the sysfs attributes.
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Enzo Matsumiya <ematsumiya@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When using nvme native multipathing, if a path related error occurs
during ->queue_rq, the request needs to be completed with
NVME_SC_HOST_PATH_ERROR so that the request can be failed over.
Introduce a helper to complete the command from ->queue_rq in a wait
that invokes nvme_complete_rq.
Signed-off-by: Chao Leng <lengchao@huawei.com>
[hch: renamed, added a return value to clean up the callers a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add nvme_cancel_tagset and nvme_cancel_admin_tagset for tear down and
reconnection error handling.
Signed-off-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The only used argument in this function is the "req".
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are no callers for nvme_reset_ctrl_sync() and
nvme_alloc_request_qid() so that we keep the symbols exported.
Unexport those functions, mark them static and update the header file
respectively.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=ayp2
-----END PGP SIGNATURE-----
Merge tag 'for-5.11/drivers-2020-12-14' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"Nothing major in here:
- NVMe pull request from Christoph:
- nvmet passthrough improvements (Chaitanya Kulkarni)
- fcloop error injection support (James Smart)
- read-only support for zoned namespaces without Zone Append
(Javier González)
- improve some error message (Minwoo Im)
- reject I/O to offline fabrics namespaces (Victor Gladkov)
- PCI queue allocation cleanups (Niklas Schnelle)
- remove an unused allocation in nvmet (Amit Engel)
- a Kconfig spelling fix (Colin Ian King)
- nvme_req_qid simplication (Baolin Wang)
- MD pull request from Song:
- Fix race condition in md_ioctl() (Dae R. Jeong)
- Initialize read_slot properly for raid10 (Kevin Vigor)
- Code cleanup (Pankaj Gupta)
- md-cluster resync/reshape fix (Zhao Heming)
- Move null_blk into its own directory (Damien Le Moal)
- null_blk zone and discard improvements (Damien Le Moal)
- bcache race fix (Dongsheng Yang)
- Set of rnbd fixes/improvements (Gioh Kim, Guoqing Jiang, Jack Wang,
Lutz Pogrell, Md Haris Iqbal)
- lightnvm NULL pointer deref fix (tangzhenhao)
- sr in_interrupt() removal (Sebastian Andrzej Siewior)
- FC endpoint security support for s390/dasd (Jan Höppner, Sebastian
Ott, Vineeth Vijayan). From the s390 arch guys, arch bits included
as it made it easier for them to funnel the feature through the
block driver tree.
- Follow up fixes (Colin Ian King)"
* tag 'for-5.11/drivers-2020-12-14' of git://git.kernel.dk/linux-block: (64 commits)
block: drop dead assignments in loop_init()
sr: Remove in_interrupt() usage in sr_init_command().
sr: Switch the sector size back to 2048 if sr_read_sector() changed it.
cdrom: Reset sector_size back it is not 2048.
drivers/lightnvm: fix a null-ptr-deref bug in pblk-core.c
null_blk: Move driver into its own directory
null_blk: Allow controlling max_hw_sectors limit
null_blk: discard zones on reset
null_blk: cleanup discard handling
null_blk: Improve implicit zone close
null_blk: improve zone locking
block: Align max_hw_sectors to logical blocksize
null_blk: Fail zone append to conventional zones
null_blk: Fix zone size initialization
bcache: fix race between setting bdev state to none and new write request direct to backing
block/rnbd: fix a null pointer dereference on dev->blk_symlink_name
block/rnbd-clt: Dynamically alloc buffer for pathname & blk_symlink_name
block/rnbd: call kobject_put in the failure path
Documentation/ABI/rnbd-srv: add document for force_close
block/rnbd-srv: close a mapped device from server side.
...
Allow ZNS NVMe SSDs to present a read-only namespace when append is not
supported, instead of rejecting the namespace directly.
This allows (i) the namespace to be used in read-only mode, which is not
a problem as the append command only affects the write path, and (ii) to
use standard management tools such as nvme-cli to choose a different
format or firmware slot that is compatible with the Linux zoned block
device.
Signed-off-by: Javier González <javier.gonz@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commands get stuck while Host NVMe-oF controller is in reconnect state.
The controller enters into reconnect state when it loses connection with
the target. It tries to reconnect every 10 seconds (default) until
a successful reconnect or until the reconnect time-out is reached.
The default reconnect time out is 10 minutes.
Applications are expecting commands to complete with success or error
within a certain timeout (30 seconds by default). The NVMe host is
enforcing that timeout while it is connected, but during reconnect the
timeout is not enforced and commands may get stuck for a long period or
even forever.
To fix this long delay due to the default timeout, introduce new
"fast_io_fail_tmo" session parameter. The timeout is measured in seconds
from the controller reconnect and any command beyond that timeout is
rejected. The new parameter value may be passed during 'connect'.
The default value of -1 means no timeout (similar to current behavior).
Signed-off-by: Victor Gladkov <victor.gladkov@kioxia.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Right now nvme_alloc_request() allocates a request from block layer
based on the value of the qid. When qid set to NVME_QID_ANY it used
blk_mq_alloc_request() else blk_mq_alloc_request_hctx().
The function nvme_alloc_request() is called from different context, The
only place where it uses non NVME_QID_ANY value is for fabrics connect
commands :-
nvme_submit_sync_cmd() NVME_QID_ANY
nvme_features() NVME_QID_ANY
nvme_sec_submit() NVME_QID_ANY
nvmf_reg_read32() NVME_QID_ANY
nvmf_reg_read64() NVME_QID_ANY
nvmf_reg_write32() NVME_QID_ANY
nvmf_connect_admin_queue() NVME_QID_ANY
nvme_submit_user_cmd() NVME_QID_ANY
nvme_alloc_request()
nvme_keep_alive() NVME_QID_ANY
nvme_alloc_request()
nvme_timeout() NVME_QID_ANY
nvme_alloc_request()
nvme_delete_queue() NVME_QID_ANY
nvme_alloc_request()
nvmet_passthru_execute_cmd() NVME_QID_ANY
nvme_alloc_request()
nvmf_connect_io_queue() QID
__nvme_submit_sync_cmd()
nvme_alloc_request()
With passthru nvme_alloc_request() now falls into the I/O fast path such
that blk_mq_alloc_request_hctx() is never gets called and that adds
additional branch check in fast path.
Split the nvme_alloc_request() into nvme_alloc_request() and
nvme_alloc_request_qid().
Replace each call of the nvme_alloc_request() with NVME_QID_ANY param
with a call to newly added nvme_alloc_request() without NVME_QID_ANY.
Replace a call to nvme_alloc_request() with QID param with a call to
newly added nvme_alloc_request() and nvme_alloc_request_qid()
based on the qid value set in the __nvme_submit_sync_cmd().
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is purely a clenaup patch, add prefix NVME to the ADMIN_TIMEOUT to
make consistent with NVME_IO_TIMEOUT.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the request's '->mq_hctx->queue_num' directly to simplify the
nvme_req_qid() function.
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove the struct used for tracking known command effects logs in a
list. This is now saved in an xarray that doesn't use these elements.
Instead, store the log directly instead of the wrapper struct.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduce sync io queues for some scenarios which just only need sync
io queues not sync all queues.
Signed-off-by: Chao Leng <lengchao@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The request's rq_disk isn't set for passthrough IO commands, so tracing
uses qid 0 for these which incorrectly decodes as an admin command. Use
the request_queue's queuedata instead since that value is always set for
the IO queues, and never set for the admin queue.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=xE9E
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"Here are the driver updates for 5.10.
A few SCSI updates in here too, in coordination with Martin as they
depend on core block changes for the shared tag bitmap.
This contains:
- NVMe pull requests via Christoph:
- fix keep alive timer modification (Amit Engel)
- order the PCI ID list more sensibly (Andy Shevchenko)
- cleanup the open by controller helper (Chaitanya Kulkarni)
- use an xarray for the CSE log lookup (Chaitanya Kulkarni)
- support ZNS in nvmet passthrough mode (Chaitanya Kulkarni)
- fix nvme_ns_report_zones (Christoph Hellwig)
- add a sanity check to nvmet-fc (James Smart)
- fix interrupt allocation when too many polled queues are
specified (Jeffle Xu)
- small nvmet-tcp optimization (Mark Wunderlich)
- fix a controller refcount leak on init failure (Chaitanya
Kulkarni)
- misc cleanups (Chaitanya Kulkarni)
- major refactoring of the scanning code (Christoph Hellwig)
- MD updates via Song:
- Bug fixes in bitmap code, from Zhao Heming
- Fix a work queue check, from Guoqing Jiang
- Fix raid5 oops with reshape, from Song Liu
- Clean up unused code, from Jason Yan
- Discard improvements, from Xiao Ni
- raid5/6 page offset support, from Yufen Yu
- Shared tag bitmap for SCSI/hisi_sas/null_blk (John, Kashyap,
Hannes)
- null_blk open/active zone limit support (Niklas)
- Set of bcache updates (Coly, Dongsheng, Qinglang)"
* tag 'drivers-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (78 commits)
md/raid5: fix oops during stripe resizing
md/bitmap: fix memory leak of temporary bitmap
md: fix the checking of wrong work queue
md/bitmap: md_bitmap_get_counter returns wrong blocks
md/bitmap: md_bitmap_read_sb uses wrong bitmap blocks
md/raid0: remove unused function is_io_in_chunk_boundary()
nvme-core: remove extra condition for vwc
nvme-core: remove extra variable
nvme: remove nvme_identify_ns_list
nvme: refactor nvme_validate_ns
nvme: move nvme_validate_ns
nvme: query namespace identifiers before adding the namespace
nvme: revalidate zone bitmaps in nvme_update_ns_info
nvme: remove nvme_update_formats
nvme: update the known admin effects
nvme: set the queue limits in nvme_update_ns_info
nvme: remove the 0 lba_shift check in nvme_update_ns_info
nvme: clean up the check for too large logic block sizes
nvme: freeze the queue over ->lba_shift updates
nvme: factor out a nvme_configure_metadata helper
...
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
The queue can trivially be derived from the nvme_ns structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
The removal of the ->revalidate_disk method broke the initialization of
the zone bitmaps, as nvme_revalidate_disk now never gets called during
initialization.
Move the zone related code from nvme_revalidate_disk into a new helper in
zns.c, and call it from nvme_alloc_ns in addition to nvme_validate_ns to
ensure the zone bitmaps are initialized during probe.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
When using linked list we have to open code the locking, search, and
destroy operations with the loops even if data structure doesn't fall
into the fast path.
One of the main advantage of having XArray to store, search, and remove
items is that it handles all the locking by itself, avoids the loops
when using linked lists, provides clear API to replace the linked list's
search and destroy loops.
This patch replaces the ctrl->cel list with XArray and removes :-
a. Extra code needed for the linked list for ctrl->cel item management
such as nvme_find_cel().
b. Destroy loop in the nvme_free_ctrl().
c. Explicit insertion locking in the nvme_get_effects_log().
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Lift opening the file open/close code from nvme_ctrl_get_by_path into
the caller, just keeping a simple nvme_ctrl_from_file() helper.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[hch: refactored a bit, split the bug fixes into a separate prep patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
* for-5.10/block: (140 commits)
bdi: replace BDI_CAP_NO_{WRITEBACK,ACCT_DIRTY} with a single flag
bdi: invert BDI_CAP_NO_ACCT_WB
bdi: replace BDI_CAP_STABLE_WRITES with a queue and a sb flag
mm: use SWP_SYNCHRONOUS_IO more intelligently
bdi: remove BDI_CAP_SYNCHRONOUS_IO
bdi: remove BDI_CAP_CGROUP_WRITEBACK
block: lift setting the readahead size into the block layer
md: update the optimal I/O size on reshape
bdi: initialize ->ra_pages and ->io_pages in bdi_init
aoe: set an optimal I/O size
bcache: inherit the optimal I/O size
drbd: remove dead code in device_to_statistics
fs: remove the unused SB_I_MULTIROOT flag
block: mark blkdev_get static
PM: mm: cleanup swsusp_swap_check
mm: split swap_type_of
PM: rewrite is_hibernate_resume_dev to not require an inode
mm: cleanup claim_swapfile
ocfs2: cleanup o2hb_region_dev_store
dasd: cleanup dasd_scan_partitions
...
Initializing the nvme hwmon retrieves a log from the controller. If the
controller is broken, we need to return the appropriate error so that
subsequent initialization doesn't attempt to continue.
Reported-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The indicated patch introduced a barrier in the sysfs_delete attribute
for the controller that rejects the request if the controller isn't
created. "Created" is defined as at least 1 call to nvme_start_ctrl().
This is problematic in error-injection testing. If an error occurs on
the initial attempt to create an association and the controller enters
reconnect(s) attempts, the admin cannot delete the controller until
either there is a successful association created or ctrl_loss_tmo
times out.
Where this issue is particularly hurtful is when the "admin" is the
nvme-cli, it is performing a connection to a discovery controller, and
it is initiated via auto-connect scripts. With the FC transport, if the
first connection attempt fails, the controller enters a normal reconnect
state but returns control to the cli thread that created the controller.
In this scenario, the cli attempts to read the discovery log via ioctl,
which fails, causing the cli to see it as an empty log and then proceeds
to delete the discovery controller. The delete is rejected and the
controller is left live. If the discovery controller reconnect then
succeeds, there is no action to delete it, and it sits live doing nothing.
Cc: <stable@vger.kernel.org> # v5.7+
Fixes: ce1518139e ("nvme: Fix controller creation races with teardown flow")
Signed-off-by: James Smart <james.smart@broadcom.com>
CC: Israel Rukshin <israelr@mellanox.com>
CC: Max Gurtovoy <maxg@mellanox.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Keith Busch <kbusch@kernel.org>
CC: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In nvme_set_queue_dying we really just want to ensure the disk and bdev
sizes are set to zero. Going through revalidate_disk leads to a somewhat
arcance and complex callchain relying on special behavior in a few
places. Instead just lift the set_capacity directly to
nvme_set_queue_dying, and rename and move the nvme_mpath_update_disk_size
helper so that we can use it in nvme_set_queue_dying to propagate the
size to the bdev without detours.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace bd_set_size with a version that takes the number of sectors
instead, as that fits most of the current and future callers much better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Users can detect if the wait has completed or not and take appropriate
actions based on this information (e.g. weather to continue
initialization or rather fail and schedule another initialization
attempt).
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Check the SCT sub-field for a path related status instead of enumerating
invididual status code. As of NVMe 1.4 this adds "Internal Path Error"
and "Controller Pathing Error" to the list, but it also future proofs for
additional status codes added to the category.
Suggested-by: Chao Leng <lengchao@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Lift all the code to decide the dispostition of a completed command
from nvme_complete_rq and nvme_failover_req into a new helper, which
returns an emum of the potential actions. nvme_complete_rq then
just switches on those and calls the proper helper for the action.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvme_end_request is a bit misnamed, as it wraps around the
blk_mq_complete_* API. It's semantics also are non-trivial, so give it
a more descriptive name and add a comment explaining the semantics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=oADH
-----END PGP SIGNATURE-----
Merge tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
- NVMe:
- ZNS support (Aravind, Keith, Matias, Niklas)
- Misc cleanups, optimizations, fixes (Baolin, Chaitanya, David,
Dongli, Max, Sagi)
- null_blk zone capacity support (Aravind)
- MD:
- raid5/6 fixes (ChangSyun)
- Warning fixes (Damien)
- raid5 stripe fixes (Guoqing, Song, Yufen)
- sysfs deadlock fix (Junxiao)
- raid10 deadlock fix (Vitaly)
- struct_size conversions (Gustavo)
- Set of bcache updates/fixes (Coly)
* tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-block: (117 commits)
md/raid5: Allow degraded raid6 to do rmw
md/raid5: Fix Force reconstruct-write io stuck in degraded raid5
raid5: don't duplicate code for different paths in handle_stripe
raid5-cache: hold spinlock instead of mutex in r5c_journal_mode_show
md: print errno in super_written
md/raid5: remove the redundant setting of STRIPE_HANDLE
md: register new md sysfs file 'uuid' read-only
md: fix max sectors calculation for super 1.0
nvme-loop: remove extra variable in create ctrl
nvme-loop: set ctrl state connecting after init
nvme-multipath: do not fall back to __nvme_find_path() for non-optimized paths
nvme-multipath: fix logic for non-optimized paths
nvme-rdma: fix controller reset hang during traffic
nvme-tcp: fix controller reset hang during traffic
nvmet: introduce the passthru Kconfig option
nvmet: introduce the passthru configfs interface
nvmet: Add passthru enable/disable helpers
nvmet: add passthru code to process commands
nvme: export nvme_find_get_ns() and nvme_put_ns()
nvme: introduce nvme_ctrl_get_by_path()
...
-----BEGIN PGP SIGNATURE-----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=abJG
-----END PGP SIGNATURE-----
Merge tag 'for-5.9/block-20200802' of git://git.kernel.dk/linux-block
Pull core block updates from Jens Axboe:
"Good amount of cleanups and tech debt removals in here, and as a
result, the diffstat shows a nice net reduction in code.
- Softirq completion cleanups (Christoph)
- Stop using ->queuedata (Christoph)
- Cleanup bd claiming (Christoph)
- Use check_events, moving away from the legacy media change
(Christoph)
- Use inode i_blkbits consistently (Christoph)
- Remove old unused writeback congestion bits (Christoph)
- Cleanup/unify submission path (Christoph)
- Use bio_uninit consistently, instead of bio_disassociate_blkg
(Christoph)
- sbitmap cleared bits handling (John)
- Request merging blktrace event addition (Jan)
- sysfs add/remove race fixes (Luis)
- blk-mq tag fixes/optimizations (Ming)
- Duplicate words in comments (Randy)
- Flush deferral cleanup (Yufen)
- IO context locking/retry fixes (John)
- struct_size() usage (Gustavo)
- blk-iocost fixes (Chengming)
- blk-cgroup IO stats fixes (Boris)
- Various little fixes"
* tag 'for-5.9/block-20200802' of git://git.kernel.dk/linux-block: (135 commits)
block: blk-timeout: delete duplicated word
block: blk-mq-sched: delete duplicated word
block: blk-mq: delete duplicated word
block: genhd: delete duplicated words
block: elevator: delete duplicated word and fix typos
block: bio: delete duplicated words
block: bfq-iosched: fix duplicated word
iocost_monitor: start from the oldest usage index
iocost: Fix check condition of iocg abs_vdebt
block: Remove callback typedefs for blk_mq_ops
block: Use non _rcu version of list functions for tag_set_list
blk-cgroup: show global disk stats in root cgroup io.stat
blk-cgroup: make iostat functions visible to stat printing
block: improve discard bio alignment in __blkdev_issue_discard()
block: change REQ_OP_ZONE_RESET and REQ_OP_ZONE_RESET_ALL to be odd numbers
block: defer flush request no matter whether we have elevator
block: make blk_timeout_init() static
block: remove retry loop in ioc_release_fn()
block: remove unnecessary ioc nested locking
block: integrate bd_start_claiming into __blkdev_get
...
Add a quirk for a device that does not support the Identify Namespace
Identification Descriptor list despite claiming 1.3 compliance.
Fixes: ea43d9709f ("nvme: fix identify error status silent ignore")
Reported-by: Ingo Brunberg <ingo_brunberg@web.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ingo Brunberg <ingo_brunberg@web.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
nvme_find_get_ns() and nvme_put_ns() are required by the target passthru
code and are exported under the NVME_TARGET_PASSTHRU namespace.
Based-on-a-patch-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme_ctrl_get_by_path() is analogous to blkdev_get_by_path() except it
gets a struct nvme_ctrl from the path to its char dev (/dev/nvme0).
It makes use of filp_open() to open the file and uses the private
data to obtain a pointer to the struct nvme_ctrl. If the fops of the
file do not match, -EINVAL is returned.
The purpose of this function is to support NVMe-OF target passthru
and is exported under the NVME_TARGET_PASSTHRU namespace.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduce a new nvme_execute_passthru_rq() helper which calls
nvme_passthru_[start|end]() around blk_execute_rq(). This ensures
all passthru calls (including nvme_submit_io()) will be wrapped
appropriately.
nvme_execute_passthru_rq() will also be useful for the nvmet passthru
code and is exported in the NVME_TARGET_PASSTHRU namespace.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Separate the code to obtain command effects from the code
to start a passthru request and move the nvme_passthru_start() and
nvme_passthru_end() functions up above nvme_submit_user_cmd() in order
that they may be used in a new helper a subsequent patch.
The new helper function will be necessary for nvmet passthru
code to determine if we need to change out of interrupt context
to handle the effects. It is exported in the NVME_TARGET_PASSTHRU
namespace.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A deadlock happens in the following scenario with multipath:
1) scan_work(nvme0) detects a new nsid while nvme0
is an optimized path to it, path nvme1 happens to be
inaccessible.
2) Before scan_work is complete nvme0 disconnect is initiated
nvme_delete_ctrl_sync() sets nvme0 state to NVME_CTRL_DELETING
3) scan_work(1) attempts to submit IO,
but nvme_path_is_optimized() observes nvme0 is not LIVE.
Since nvme1 is a possible path IO is requeued and scan_work hangs.
--
Workqueue: nvme-wq nvme_scan_work [nvme_core]
kernel: Call Trace:
kernel: __schedule+0x2b9/0x6c0
kernel: schedule+0x42/0xb0
kernel: io_schedule+0x16/0x40
kernel: do_read_cache_page+0x438/0x830
kernel: read_cache_page+0x12/0x20
kernel: read_dev_sector+0x27/0xc0
kernel: read_lba+0xc1/0x220
kernel: efi_partition+0x1e6/0x708
kernel: check_partition+0x154/0x244
kernel: rescan_partitions+0xae/0x280
kernel: __blkdev_get+0x40f/0x560
kernel: blkdev_get+0x3d/0x140
kernel: __device_add_disk+0x388/0x480
kernel: device_add_disk+0x13/0x20
kernel: nvme_mpath_set_live+0x119/0x140 [nvme_core]
kernel: nvme_update_ns_ana_state+0x5c/0x60 [nvme_core]
kernel: nvme_set_ns_ana_state+0x1e/0x30 [nvme_core]
kernel: nvme_parse_ana_log+0xa1/0x180 [nvme_core]
kernel: nvme_mpath_add_disk+0x47/0x90 [nvme_core]
kernel: nvme_validate_ns+0x396/0x940 [nvme_core]
kernel: nvme_scan_work+0x24f/0x380 [nvme_core]
kernel: process_one_work+0x1db/0x380
kernel: worker_thread+0x249/0x400
kernel: kthread+0x104/0x140
--
4) Delete also hangs in flush_work(ctrl->scan_work)
from nvme_remove_namespaces().
Similiarly a deadlock with ana_work may happen: if ana_work has started
and calls nvme_mpath_set_live and device_add_disk, it will
trigger I/O. When we trigger disconnect I/O will block because
our accessible (optimized) path is disconnecting, but the alternate
path is inaccessible, so I/O blocks. Then disconnect tries to flush
the ana_work and hangs.
[ 605.550896] Workqueue: nvme-wq nvme_ana_work [nvme_core]
[ 605.552087] Call Trace:
[ 605.552683] __schedule+0x2b9/0x6c0
[ 605.553507] schedule+0x42/0xb0
[ 605.554201] io_schedule+0x16/0x40
[ 605.555012] do_read_cache_page+0x438/0x830
[ 605.556925] read_cache_page+0x12/0x20
[ 605.557757] read_dev_sector+0x27/0xc0
[ 605.558587] amiga_partition+0x4d/0x4c5
[ 605.561278] check_partition+0x154/0x244
[ 605.562138] rescan_partitions+0xae/0x280
[ 605.563076] __blkdev_get+0x40f/0x560
[ 605.563830] blkdev_get+0x3d/0x140
[ 605.564500] __device_add_disk+0x388/0x480
[ 605.565316] device_add_disk+0x13/0x20
[ 605.566070] nvme_mpath_set_live+0x5e/0x130 [nvme_core]
[ 605.567114] nvme_update_ns_ana_state+0x2c/0x30 [nvme_core]
[ 605.568197] nvme_update_ana_state+0xca/0xe0 [nvme_core]
[ 605.569360] nvme_parse_ana_log+0xa1/0x180 [nvme_core]
[ 605.571385] nvme_read_ana_log+0x76/0x100 [nvme_core]
[ 605.572376] nvme_ana_work+0x15/0x20 [nvme_core]
[ 605.573330] process_one_work+0x1db/0x380
[ 605.574144] worker_thread+0x4d/0x400
[ 605.574896] kthread+0x104/0x140
[ 605.577205] ret_from_fork+0x35/0x40
[ 605.577955] INFO: task nvme:14044 blocked for more than 120 seconds.
[ 605.579239] Tainted: G OE 5.3.5-050305-generic #201910071830
[ 605.580712] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 605.582320] nvme D 0 14044 14043 0x00000000
[ 605.583424] Call Trace:
[ 605.583935] __schedule+0x2b9/0x6c0
[ 605.584625] schedule+0x42/0xb0
[ 605.585290] schedule_timeout+0x203/0x2f0
[ 605.588493] wait_for_completion+0xb1/0x120
[ 605.590066] __flush_work+0x123/0x1d0
[ 605.591758] __cancel_work_timer+0x10e/0x190
[ 605.593542] cancel_work_sync+0x10/0x20
[ 605.594347] nvme_mpath_stop+0x2f/0x40 [nvme_core]
[ 605.595328] nvme_stop_ctrl+0x12/0x50 [nvme_core]
[ 605.596262] nvme_do_delete_ctrl+0x3f/0x90 [nvme_core]
[ 605.597333] nvme_sysfs_delete+0x5c/0x70 [nvme_core]
[ 605.598320] dev_attr_store+0x17/0x30
Fix this by introducing a new state: NVME_CTRL_DELETE_NOIO, which will
indicate the phase of controller deletion where I/O cannot be allowed
to access the namespace. NVME_CTRL_DELETING still allows mpath I/O to
be issued to the bottom device, and only after we flush the ana_work
and scan_work (after nvme_stop_ctrl and nvme_prep_remove_namespaces)
we change the state to NVME_CTRL_DELETING_NOIO. Also we prevent ana_work
from re-firing by aborting early if we are not LIVE, so we should be safe
here.
In addition, change the transport drivers to follow the updated state
machine.
Fixes: 0d0b660f21 ("nvme: add ANA support")
Reported-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We are starting to see some non-trivial states
so lets start documenting them.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Saving the nvme controller's page size was from a time when the driver
tried to use different sized pages, but this value is always set to
a constant, and has been this way for some time. Remove the 'page_size'
field and replace its usage with the constant value.
This also lets the compiler make some micro-optimizations in the io
path, and that's always a good thing.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit 3b4b19721e ("nvme: fix possible deadlock when I/O is
blocked") reverted multipath head disk revalidation due to deadlocks
caused by holding the bd_mutex during revalidate.
Updating the multipath disk blockdev size is still required though for
userspace to be able to observe any resizing while the device is
mounted. Directly update the bdev inode size to avoid unnecessarily
holding the bdev->bd_mutex.
Fixes: 3b4b19721e ("nvme: fix possible deadlock when I/O is
blocked")
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for NVM Express Zoned Namespaces (ZNS) Command Set defined
in NVM Express TP4053. Zoned namespaces are discovered based on their
Command Set Identifier reported in the namespaces Namespace
Identification Descriptor list. A successfully discovered Zoned
Namespace will be registered with the block layer as a host managed
zoned block device with Zone Append command support. A namespace that
does not support append is not supported by the driver.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <keith.busch@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The Commands Supported and Effects log page was extended with a CSI
field that enables the host to query the log page for each command set
supported. Retrieve this log page for each command set that an attached
namespace supports, and save a pointer to that log in the namespace head.
Reviewed-by: Matias Bjørling <matias.bjorling@wdc.com>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <keith.busch@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Implements support for multiple I/O Command Sets. NVMe TP 4056
introduces a method to enumerate multiple command sets per namespace. If
the command set is exposed, this method for enumeration will be used
instead of the traditional method that uses the CC.CSS register command
set register for command set identification.
For namespaces where the Command Set Identifier is not supported or
recognized, the specific namespace will not be created.
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Matias Bjørling <matias.bjorling@wdc.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8CYDYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGcQkH/2vOsPf79yWtsc7x
hd2LpCPfrm7T1xlQcYcXbEbyRI8sqPmguixO8pRI1ePl2lBZ7KurfyeYgYZNGpFU
t74Ph6A6dSWoCgO68Genm/SQuK8ic6o9n1Vr8tDsGDp5KlHWNaweq4JwHrsPmO1T
cI0PR/ClAhLG8cQZ4x988Es5HTNGY17XK27e+M/zKYxSMGY2NRdJBGQIq964i5Q8
2d9G0rtVCaVDzgjrLwaFm6RBu21Il7HV6KsBsacyTFiL1ywx2vnUHzeZQyvuJSOQ
4YpLo9v4tBP10WHC50LRStZyO0qRwPVd/Yl7fL4R/CKsJT9H4uiwasVoEBVSL/k6
CUn3JL0=
=P/Vx
-----END PGP SIGNATURE-----
Merge tag 'v5.8-rc4' into for-5.9/drivers
Merge in 5.8-rc4 for-5.9/block to setup for-5.9/drivers, to provide
a clean base and making the life for the NVMe changes easier.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v5.8-rc4': (732 commits)
Linux 5.8-rc4
x86/ldt: use "pr_info_once()" instead of open-coding it badly
MIPS: Do not use smp_processor_id() in preemptible code
MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen
.gitignore: Do not track `defconfig` from `make savedefconfig`
io_uring: fix regression with always ignoring signals in io_cqring_wait()
x86/ldt: Disable 16-bit segments on Xen PV
x86/entry/32: Fix #MC and #DB wiring on x86_32
x86/entry/xen: Route #DB correctly on Xen PV
x86/entry, selftests: Further improve user entry sanity checks
x86/entry/compat: Clear RAX high bits on Xen PV SYSENTER
i2c: mlxcpld: check correct size of maximum RECV_LEN packet
i2c: add Kconfig help text for slave mode
i2c: slave-eeprom: update documentation
i2c: eg20t: Load module automatically if ID matches
i2c: designware: platdrv: Set class based on DMI
i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665
mm/page_alloc: fix documentation error
vmalloc: fix the owner argument for the new __vmalloc_node_range callers
mm/cma.c: use exact_nid true to fix possible per-numa cma leak
...
The make_request_fn is a little weird in that it sits directly in
struct request_queue instead of an operation vector. Replace it with
a block_device_operations method called submit_bio (which describes much
better what it does). Also remove the request_queue argument to it, as
the queue can be derived pretty trivially from the bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the following scenario scan_work and ana_work will deadlock:
When scan_work calls nvme_mpath_add_disk() this holds ana_lock
and invokes nvme_parse_ana_log(), which may issue IO
in device_add_disk() and hang waiting for an accessible path.
While nvme_mpath_set_live() only called when nvme_state_is_live(),
a transition may cause NVME_SC_ANA_TRANSITION and requeue the IO.
Since nvme_mpath_set_live() holds ns->head->lock, an ana_work on
ANY ctrl will not be able to complete nvme_mpath_set_live()
on the same ns->head, which is required in order to update
the new accessible path and remove NVME_NS_ANA_PENDING..
Therefore IO never completes: deadlock [1].
Fix:
Move device_add_disk out of the head->lock and protect it with an
atomic test_and_set for a new NVME_NS_HEAD_HAS_DISK bit.
[1]:
kernel: INFO: task kworker/u8:2:160 blocked for more than 120 seconds.
kernel: Tainted: G OE 5.3.5-050305-generic #201910071830
kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kernel: kworker/u8:2 D 0 160 2 0x80004000
kernel: Workqueue: nvme-wq nvme_ana_work [nvme_core]
kernel: Call Trace:
kernel: __schedule+0x2b9/0x6c0
kernel: schedule+0x42/0xb0
kernel: schedule_preempt_disabled+0xe/0x10
kernel: __mutex_lock.isra.0+0x182/0x4f0
kernel: __mutex_lock_slowpath+0x13/0x20
kernel: mutex_lock+0x2e/0x40
kernel: nvme_update_ns_ana_state+0x22/0x60 [nvme_core]
kernel: nvme_update_ana_state+0xca/0xe0 [nvme_core]
kernel: nvme_parse_ana_log+0xa1/0x180 [nvme_core]
kernel: nvme_read_ana_log+0x76/0x100 [nvme_core]
kernel: nvme_ana_work+0x15/0x20 [nvme_core]
kernel: process_one_work+0x1db/0x380
kernel: worker_thread+0x4d/0x400
kernel: kthread+0x104/0x140
kernel: ret_from_fork+0x35/0x40
kernel: INFO: task kworker/u8:4:439 blocked for more than 120 seconds.
kernel: Tainted: G OE 5.3.5-050305-generic #201910071830
kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kernel: kworker/u8:4 D 0 439 2 0x80004000
kernel: Workqueue: nvme-wq nvme_scan_work [nvme_core]
kernel: Call Trace:
kernel: __schedule+0x2b9/0x6c0
kernel: schedule+0x42/0xb0
kernel: io_schedule+0x16/0x40
kernel: do_read_cache_page+0x438/0x830
kernel: read_cache_page+0x12/0x20
kernel: read_dev_sector+0x27/0xc0
kernel: read_lba+0xc1/0x220
kernel: efi_partition+0x1e6/0x708
kernel: check_partition+0x154/0x244
kernel: rescan_partitions+0xae/0x280
kernel: __blkdev_get+0x40f/0x560
kernel: blkdev_get+0x3d/0x140
kernel: __device_add_disk+0x388/0x480
kernel: device_add_disk+0x13/0x20
kernel: nvme_mpath_set_live+0x119/0x140 [nvme_core]
kernel: nvme_update_ns_ana_state+0x5c/0x60 [nvme_core]
kernel: nvme_mpath_add_disk+0xbe/0x100 [nvme_core]
kernel: nvme_validate_ns+0x396/0x940 [nvme_core]
kernel: nvme_scan_work+0x256/0x390 [nvme_core]
kernel: process_one_work+0x1db/0x380
kernel: worker_thread+0x4d/0x400
kernel: kthread+0x104/0x140
kernel: ret_from_fork+0x35/0x40
Fixes: 0d0b660f21 ("nvme: add ANA support")
Signed-off-by: Anton Eidelman <anton@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the new blk_mq_complete_request_remote helper to avoid an indirect
function call in the completion fast path.
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the call to blk_should_fake_timeout out of blk_mq_complete_request
and into the drivers, skipping call sites that are obvious error
handlers, and remove the now superflous blk_mq_force_complete_rq helper.
This ensures we don't keep injecting errors into completions that just
terminate the Linux request after the hardware has been reset or the
command has been aborted.
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The status can be trivially derived from the bio itself. That also avoid
callers like NVMe to incorrectly pass a blk_status_t instead of the errno,
and the overhead of translating the blk_status_t to the errno in the I/O
completion fast path when no tracing is enabled.
Fixes: 35fe0d12c8 ("nvme: trace bio completion")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
SGL size of metadata is usually small. Thus, 1 inline sg should cover
most cases. The macro will be used for pre-allocate a single SGL entry
for metadata. The preallocation of small inline SGLs depends on SG_CHAIN
capability so if the ARCH doesn't support SG_CHAIN, use the runtime
allocation for the SGL. This patch is a preparation for adding metadata
(T10-PI) over fabric support.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch doesn't change any logic, and is needed as a preparation
for adding PI support for fabrics drivers that will use an extended
LBA format for metadata and will support more than 1 integrity segment.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move the nvme_ns_has_pi() inline from core.c to the nvme.h header.
This allows use by the transports.
Signed-off-by: James Smart <jsmart2021@gmail.com>
[maxg: added a comment for nvme_ns_has_pi()]
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is a preparation for adding support for metadata in fabric
controllers. New flag will imply that NVMe namespace supports getting
metadata that was originally generated by host's block layer.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Replace the specific ext boolean (that implies on extended LBA format)
with a feature in the new namespace features flag. This is a preparation
for adding more namespace features (such as metadata specific features).
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The nvme_put_ctrl() is implemented earlier as an inline function so
this declaration isn't required.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move the quirked chunk_sectors setting to the same location as noiob so
one place registers this setting. And since the noiob value is only used
locally, remove the member from struct nvme_ns.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reject a new shared namespace if a duplicate unshared namespace exists.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Various nvme commands use a zeroes based number of dwords field. Create
a helper function to convert byte lengths to this format.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Calling nvme_sysfs_delete() when the controller is in the middle of
creation may cause several bugs. If the controller is in NEW state we
remove delete_controller file and don't delete the controller. The user
will not be able to use nvme disconnect command on that controller again,
although the controller may be active. Other bugs may happen if the
controller is in the middle of create_ctrl callback and
nvme_do_delete_ctrl() starts. For example, freeing I/O tagset at
nvme_do_delete_ctrl() before it was allocated at create_ctrl callback.
To fix all those races don't allow the user to delete the controller
before it was fully created.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
The nvme multipath error handling defaults to controller reset if the
error is unknown. There are, however, no existing nvme status codes that
indicate a reset should be used, and resetting causes unnecessary
disruption to the rest of IO.
Change nvme's error handling to first check if failover should happen.
If not, let the normal error handling take over rather than reset the
controller.
Based-on-a-patch-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Meneghini <johnm@netapp.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
nvme_rdma_alloc_tagset() preallocates a big buffer for the IO SGL based
on SG_CHUNK_SIZE.
Modern DMA engines are often capable of dealing with very big segments so
the SG_CHUNK_SIZE is often too big. SG_CHUNK_SIZE results in a static 4KB
SGL allocation per command.
If a controller has lots of deep queues, preallocation for the sg list can
consume substantial amounts of memory. For nvme-rdma, nr_hw_queues can be
128 and each queue's depth 128. This means the resulting preallocation
for the data SGL is 128*128*4K = 64MB per controller.
Switch to runtime allocation for SGL for lists longer than 2 entries. This
is the approach used by NVMe PCI so it should be reasonable for NVMeOF as
well. Runtime SGL allocation has always been the case for the legacy I/O
path so this is nothing new.
The preallocated small SGL depends on SG_CHAIN so if the ARCH doesn't
support SG_CHAIN, use only runtime allocation for the SGL.
We didn't notice of a performance degradation, since for small IOs we'll
use the inline SG and for the bigger IOs the allocation of a bigger SGL
from slab is fast enough.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oyE3
-----END PGP SIGNATURE-----
Merge tag 'for-5.5/drivers-post-20191122' of git://git.kernel.dk/linux-block
Pull additional block driver updates from Jens Axboe:
"Here's another block driver update, done to avoid conflicts with the
zoned changes coming next.
This contains:
- Prepare SCSI sd for zone open/close/finish support
- Small NVMe pull request
- hwmon support (Akinobu)
- add new co-maintainer (Christoph)
- work-around for a discard issue on non-conformant drives
(Eduard)
- Small nbd leak fix"
* tag 'for-5.5/drivers-post-20191122' of git://git.kernel.dk/linux-block:
nbd: prevent memory leak
nvme: hwmon: add quirk to avoid changing temperature threshold
nvme: hwmon: provide temperature min and max values for each sensor
nvmet: add another maintainer
nvme: Discard workaround for non-conformant devices
nvme: Add hardware monitoring support
scsi: sd_zbc: add zone open, close, and finish support
-----BEGIN PGP SIGNATURE-----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=i0jf
-----END PGP SIGNATURE-----
Merge tag 'for-5.5/drivers-20191121' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"Here are the main block driver updates for 5.5. Nothing major in here,
mostly just fixes. This contains:
- a set of bcache changes via Coly
- MD changes from Song
- loop unmap write-zeroes fix (Darrick)
- spelling fixes (Geert)
- zoned additions cleanups to null_blk/dm (Ajay)
- allow null_blk online submit queue changes (Bart)
- NVMe changes via Keith, nothing major here either"
* tag 'for-5.5/drivers-20191121' of git://git.kernel.dk/linux-block: (56 commits)
Revert "bcache: fix fifo index swapping condition in journal_pin_cmp()"
drivers/md/raid5-ppl.c: use the new spelling of RWH_WRITE_LIFE_NOT_SET
drivers/md/raid5.c: use the new spelling of RWH_WRITE_LIFE_NOT_SET
bcache: don't export symbols
bcache: remove the extra cflags for request.o
bcache: at least try to shrink 1 node in bch_mca_scan()
bcache: add idle_max_writeback_rate sysfs interface
bcache: add code comments in bch_btree_leaf_dirty()
bcache: fix deadlock in bcache_allocator
bcache: add code comment bch_keylist_pop() and bch_keylist_pop_front()
bcache: deleted code comments for dead code in bch_data_insert_keys()
bcache: add more accurate error messages in read_super()
bcache: fix static checker warning in bcache_device_free()
bcache: fix a lost wake-up problem caused by mca_cannibalize_lock
bcache: fix fifo index swapping condition in journal_pin_cmp()
md/raid10: prevent access of uninitialized resync_pages offset
md: avoid invalid memory access for array sb->dev_roles
md/raid1: avoid soft lockup under high load
null_blk: add zone open, close, and finish support
dm: add zone open, close and finish support
...
This adds a new quirk NVME_QUIRK_NO_TEMP_THRESH_CHANGE to avoid changing
the value of the temperature threshold feature for specific devices that
show undesirable behavior.
Guenter reported:
"On my Intel NVME drive (SSDPEKKW512G7), writing any minimum limit on the
Composite temperature sensor results in a temperature warning, and that
warning is sticky until I reset the controller.
It doesn't seem to matter which temperature I write; writing -273000 has
the same result."
The Intel NVMe has the latest firmware version installed, so this isn't
a problem that was ever fixed.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jean Delvare <jdelvare@suse.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
nvme devices report temperature information in the controller information
(for limits) and in the smart log. Currently, the only means to retrieve
this information is the nvme command line interface, which requires
super-user privileges.
At the same time, it would be desirable to be able to use NVMe temperature
information for thermal control.
This patch adds support to read NVMe temperatures from the kernel using the
hwmon API and adds temperature zones for NVMe drives. The thermal subsystem
can use this information to set thermal policies, and userspace can access
it using libsensors and/or the "sensors" command.
Example output from the "sensors" command:
nvme0-pci-0100
Adapter: PCI adapter
Composite: +39.0°C (high = +85.0°C, crit = +85.0°C)
Sensor 1: +39.0°C
Sensor 2: +41.0°C
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Introduce the new helper function nvme_lba_to_sect() to convert a device
logical block number to a 512B sector number. Use this new helper in
obvious places, cleaning up the code.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename nvme_block_nr() to nvme_sect_to_lba() and use SECTOR_SHIFT
instead of its hard coded value 9. Also add a comment to decribe this
helper.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function improves code readability and reduces code duplication.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prevent simultaneous controller disabling/enabling tasks from interfering
with each other through a function to wait until the task successfully
transitioned the controller to the RESETTING state. This ensures disabling
the controller will not be interrupted by another reset path, otherwise
a concurrent reset may leave the controller in the wrong state.
Tested-by: Edmund Nadolski <edmund.nadolski@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
The admin only state was intended to fence off actions that don't
apply to a non-IO capable controller. The only actual user of this is
the scan_work, and pci was the only transport to ever set this state.
The consequence of having this state is placing an additional burden on
every other action that applies to both live and admin only controllers.
Remove the admin only state and place the admin only burden on the only
place that actually cares: scan_work.
This also prepares to make it easier to temporarily pause a LIVE state
so that we don't need to remember which state the controller had been in
prior to the pause.
Tested-by: Edmund Nadolski <edmund.nadolski@intel.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Qt+h
-----END PGP SIGNATURE-----
Merge tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Two NVMe pull requests:
- ana log parse fix from Anton
- nvme quirks support for Apple devices from Ben
- fix missing bio completion tracing for multipath stack devices
from Hannes and Mikhail
- IP TOS settings for nvme rdma and tcp transports from Israel
- rq_dma_dir cleanups from Israel
- tracing for Get LBA Status command from Minwoo
- Some nvme-tcp cleanups from Minwoo, Potnuri and Myself
- Some consolidation between the fabrics transports for handling
the CAP register
- reset race with ns scanning fix for fabrics (move fabrics
commands to a dedicated request queue with a different lifetime
from the admin request queue)."
- controller reset and namespace scan races fixes
- nvme discovery log change uevent support
- naming improvements from Keith
- multiple discovery controllers reject fix from James
- some regular cleanups from various people
- Series fixing (and re-fixing) null_blk debug printing and nr_devices
checks (André)
- A few pull requests from Song, with fixes from Andy, Guoqing,
Guilherme, Neil, Nigel, and Yufen.
- REQ_OP_ZONE_RESET_ALL support (Chaitanya)
- Bio merge handling unification (Christoph)
- Pick default elevator correctly for devices with special needs
(Damien)
- Block stats fixes (Hou)
- Timeout and support devices nbd fixes (Mike)
- Series fixing races around elevator switching and device add/remove
(Ming)
- sed-opal cleanups (Revanth)
- Per device weight support for BFQ (Fam)
- Support for blk-iocost, a new model that can properly account cost of
IO workloads. (Tejun)
- blk-cgroup writeback fixes (Tejun)
- paride queue init fixes (zhengbin)
- blk_set_runtime_active() cleanup (Stanley)
- Block segment mapping optimizations (Bart)
- lightnvm fixes (Hans/Minwoo/YueHaibing)
- Various little fixes and cleanups
* tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block: (186 commits)
null_blk: format pr_* logs with pr_fmt
null_blk: match the type of parameter nr_devices
null_blk: do not fail the module load with zero devices
block: also check RQF_STATS in blk_mq_need_time_stamp()
block: make rq sector size accessible for block stats
bfq: Fix bfq linkage error
raid5: use bio_end_sector in r5_next_bio
raid5: remove STRIPE_OPS_REQ_PENDING
md: add feature flag MD_FEATURE_RAID0_LAYOUT
md/raid0: avoid RAID0 data corruption due to layout confusion.
raid5: don't set STRIPE_HANDLE to stripe which is in batch list
raid5: don't increment read_errors on EILSEQ return
nvmet: fix a wrong error status returned in error log page
nvme: send discovery log page change events to userspace
nvme: add uevent variables for controller devices
nvme: enable aen regardless of the presence of I/O queues
nvme-fabrics: allow discovery subsystems accept a kato
nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery()
nvme: Remove redundant assignment of cq vector
nvme: Assign subsys instance from first ctrl
...
We have a fundamental issue that fabric commands use the admin_q.
The reason is, that admin-connect, register reads and writes and
admin commands cannot be guaranteed ordering while we are running
controller resets.
For example, when we reset a controller we perform:
1. disable the controller
2. teardown the admin queue
3. re-establish the admin queue
4. enable the controller
In order to perform (3), we need to unquiesce the admin queue, however
we may have some admin commands that are already pending on the
quiesced admin_q and will immediate execute when we unquiesce it before
we execute (4). The host must not send admin commands to the controller
before enabling the controller.
To fix this, we have the fabric commands (admin connect and property
get/set, but not I/O queue connect) use a separate fabrics_q and make
sure to quiesce the admin_q before we disable the controller, and
unquiesce it only after we enable the controller.
This fixes the error prints from nvmet in a controller reset storm test:
kernel: nvmet: got cmd 6 while CC.EN == 0 on qid = 0
Which indicate that the host is sending an admin command when the
controller is not enabled.
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Another issue with the Apple T2 based 2018 controllers seem to be
that they blow up (and shut the machine down) if there's a tag
collision between the IO queue and the Admin queue.
My suspicion is that they use our tags for their internal tracking
and don't mix them with the queue id. They also seem to not like
when tags go beyond the IO queue depth, ie 128 tags.
This adds a quirk that marks tags 0..31 of the IO queue reserved
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Based on reverse engineering and original patch by
Paul Pawlowski <paul@mrarm.io>
This adds support for Apple weird implementation of NVME in their
2018 or later machines. It accounts for the twice-as-big SQ entries
for the IO queues, and the fact that only interrupt vector 0 appears
to function properly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
When native multipathing is enabled we cannot enable blktrace for
the underlying paths, so any completion is never traced.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[fixed-up by Mikhail for non-multipath-build]
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
All seem to call it with ctrl->cap so no need to pass it
at all.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
nvme_enable_ctrl reads the cap register right after, so
no need to do that locally in the transport driver. Have
sqsize setting in nvme_init_identify.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
One of the components in LiteON CL1 device has limitations that
can be encountered based upon boundary race conditions using the
nvme bus specific suspend to idle flow.
When this situation occurs the drive doesn't resume properly from
suspend-to-idle.
LiteON has confirmed this problem and fixed in the next firmware
version. As this firmware is already in the field, avoid running
nvme specific suspend to idle flow.
Fixes: d916b1be94 ("nvme-pci: use host managed power state for suspend")
Link: http://lists.infradead.org/pipermail/linux-nvme/2019-July/thread.html
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Charles Hyde <charles.hyde@dellteam.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With multipath enabled, nvme_scan_work() can read from the device
(through nvme_mpath_add_disk()) and hang [1]. However, with fabrics,
once ctrl->state is set to NVME_CTRL_DELETING, the reads will hang
(see nvmf_check_ready()) and the mpath stack device make_request
will block if head->list is not empty. However, when the head->list
consistst of only DELETING/DEAD controllers, we should actually not
block, but rather fail immediately.
In addition, before we go ahead and remove the namespaces, make sure
to clear the current path and kick the requeue list so that the
request will fast fail upon requeuing.
[1]:
--
INFO: task kworker/u4:3:166 blocked for more than 120 seconds.
Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:3 D 0 166 2 0x80004000
Workqueue: nvme-wq nvme_scan_work
Call Trace:
__schedule+0x851/0x1400
schedule+0x99/0x210
io_schedule+0x21/0x70
do_read_cache_page+0xa57/0x1330
read_cache_page+0x4a/0x70
read_dev_sector+0xbf/0x380
amiga_partition+0xc4/0x1230
check_partition+0x30f/0x630
rescan_partitions+0x19a/0x980
__blkdev_get+0x85a/0x12f0
blkdev_get+0x2a5/0x790
__device_add_disk+0xe25/0x1250
device_add_disk+0x13/0x20
nvme_mpath_set_live+0x172/0x2b0
nvme_update_ns_ana_state+0x130/0x180
nvme_set_ns_ana_state+0x9a/0xb0
nvme_parse_ana_log+0x1c3/0x4a0
nvme_mpath_add_disk+0x157/0x290
nvme_validate_ns+0x1017/0x1bd0
nvme_scan_work+0x44d/0x6a0
process_one_work+0x7d7/0x1240
worker_thread+0x8e/0xff0
kthread+0x2c3/0x3b0
ret_from_fork+0x35/0x40
INFO: task kworker/u4:1:1034 blocked for more than 120 seconds.
Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:1 D 0 1034 2 0x80004000
Workqueue: nvme-delete-wq nvme_delete_ctrl_work
Call Trace:
__schedule+0x851/0x1400
schedule+0x99/0x210
schedule_timeout+0x390/0x830
wait_for_completion+0x1a7/0x310
__flush_work+0x241/0x5d0
flush_work+0x10/0x20
nvme_remove_namespaces+0x85/0x3d0
nvme_do_delete_ctrl+0xb4/0x1e0
nvme_delete_ctrl_work+0x15/0x20
process_one_work+0x7d7/0x1240
worker_thread+0x8e/0xff0
kthread+0x2c3/0x3b0
ret_from_fork+0x35/0x40
--
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
When the user issues a command with side effects, we will end up freezing
the namespace request queue when updating disk info (and the same for
the corresponding mpath disk node).
However, we are not freezing the mpath node request queue,
which means that mpath I/O can still come in and block on blk_queue_enter
(called from nvme_ns_head_make_request -> direct_make_request).
This is a deadlock, because blk_queue_enter will block until the inner
namespace request queue is unfroze, but that process is blocked because
the namespace revalidation is trying to update the mpath disk info
and freeze its request queue (which will never complete because
of the I/O that is blocked on blk_queue_enter).
Fix this by freezing all the subsystem nsheads request queues before
executing the passthru command. Given that these commands are infrequent
we should not worry about this temporary I/O freeze to keep things sane.
Here is the matching hang traces:
--
[ 374.465002] INFO: task systemd-udevd:17994 blocked for more than 122 seconds.
[ 374.472975] Not tainted 5.2.0-rc3-mpdebug+ #42
[ 374.478522] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 374.487274] systemd-udevd D 0 17994 1 0x00000000
[ 374.493407] Call Trace:
[ 374.496145] __schedule+0x2ef/0x620
[ 374.500047] schedule+0x38/0xa0
[ 374.503569] blk_queue_enter+0x139/0x220
[ 374.507959] ? remove_wait_queue+0x60/0x60
[ 374.512540] direct_make_request+0x60/0x130
[ 374.517219] nvme_ns_head_make_request+0x11d/0x420 [nvme_core]
[ 374.523740] ? generic_make_request_checks+0x307/0x6f0
[ 374.529484] generic_make_request+0x10d/0x2e0
[ 374.534356] submit_bio+0x75/0x140
[ 374.538163] ? guard_bio_eod+0x32/0xe0
[ 374.542361] submit_bh_wbc+0x171/0x1b0
[ 374.546553] block_read_full_page+0x1ed/0x330
[ 374.551426] ? check_disk_change+0x70/0x70
[ 374.556008] ? scan_shadow_nodes+0x30/0x30
[ 374.560588] blkdev_readpage+0x18/0x20
[ 374.564783] do_read_cache_page+0x301/0x860
[ 374.569463] ? blkdev_writepages+0x10/0x10
[ 374.574037] ? prep_new_page+0x88/0x130
[ 374.578329] ? get_page_from_freelist+0xa2f/0x1280
[ 374.583688] ? __alloc_pages_nodemask+0x179/0x320
[ 374.588947] read_cache_page+0x12/0x20
[ 374.593142] read_dev_sector+0x2d/0xd0
[ 374.597337] read_lba+0x104/0x1f0
[ 374.601046] find_valid_gpt+0xfa/0x720
[ 374.605243] ? string_nocheck+0x58/0x70
[ 374.609534] ? find_valid_gpt+0x720/0x720
[ 374.614016] efi_partition+0x89/0x430
[ 374.618113] ? string+0x48/0x60
[ 374.621632] ? snprintf+0x49/0x70
[ 374.625339] ? find_valid_gpt+0x720/0x720
[ 374.629828] check_partition+0x116/0x210
[ 374.634214] rescan_partitions+0xb6/0x360
[ 374.638699] __blkdev_reread_part+0x64/0x70
[ 374.643377] blkdev_reread_part+0x23/0x40
[ 374.647860] blkdev_ioctl+0x48c/0x990
[ 374.651956] block_ioctl+0x41/0x50
[ 374.655766] do_vfs_ioctl+0xa7/0x600
[ 374.659766] ? locks_lock_inode_wait+0xb1/0x150
[ 374.664832] ksys_ioctl+0x67/0x90
[ 374.668539] __x64_sys_ioctl+0x1a/0x20
[ 374.672732] do_syscall_64+0x5a/0x1c0
[ 374.676828] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 374.738474] INFO: task nvmeadm:49141 blocked for more than 123 seconds.
[ 374.745871] Not tainted 5.2.0-rc3-mpdebug+ #42
[ 374.751419] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 374.760170] nvmeadm D 0 49141 36333 0x00004080
[ 374.766301] Call Trace:
[ 374.769038] __schedule+0x2ef/0x620
[ 374.772939] schedule+0x38/0xa0
[ 374.776452] blk_mq_freeze_queue_wait+0x59/0x100
[ 374.781614] ? remove_wait_queue+0x60/0x60
[ 374.786192] blk_mq_freeze_queue+0x1a/0x20
[ 374.790773] nvme_update_disk_info.isra.57+0x5f/0x350 [nvme_core]
[ 374.797582] ? nvme_identify_ns.isra.50+0x71/0xc0 [nvme_core]
[ 374.804006] __nvme_revalidate_disk+0xe5/0x110 [nvme_core]
[ 374.810139] nvme_revalidate_disk+0xa6/0x120 [nvme_core]
[ 374.816078] ? nvme_submit_user_cmd+0x11e/0x320 [nvme_core]
[ 374.822299] nvme_user_cmd+0x264/0x370 [nvme_core]
[ 374.827661] nvme_dev_ioctl+0x112/0x1d0 [nvme_core]
[ 374.833114] do_vfs_ioctl+0xa7/0x600
[ 374.837117] ? __audit_syscall_entry+0xdd/0x130
[ 374.842184] ksys_ioctl+0x67/0x90
[ 374.845891] __x64_sys_ioctl+0x1a/0x20
[ 374.850082] do_syscall_64+0x5a/0x1c0
[ 374.854178] entry_SYSCALL_64_after_hwframe+0x44/0xa9
--
Reported-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
Tested-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
>From the NVMe 1.4 spec:
NSFEAT bit 4 if set to 1: indicates that the fields NPWG, NPWA, NPDG, NPDA,
and NOWS are defined for this namespace and should be used by the host for
I/O optimization;
[ ... ]
Namespace Preferred Write Granularity (NPWG): This field indicates the
smallest recommended write granularity in logical blocks for this namespace.
This is a 0's based value. The size indicated should be less than or equal
to Maximum Data Transfer Size (MDTS) that is specified in units of minimum
memory page size. The value of this field may change if the namespace is
reformatted. The size should be a multiple of Namespace Preferred Write
Alignment (NPWA). Refer to section 8.25 for how this field is utilized to
improve performance and endurance.
[ ... ]
Each Write, Write Uncorrectable, or Write Zeroes commands should address a
multiple of Namespace Preferred Write Granularity (NPWG) (refer to Figure
245) and Stream Write Size (SWS) (refer to Figure 515) logical blocks (as
expressed in the NLB field), and the SLBA field of the command should be
aligned to Namespace Preferred Write Alignment (NPWA) (refer to Figure 245)
for best performance.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This enables to inject errors into the commands submitted to the admin
queue.
It is useful to test error handling in the controller initialization.
# echo 100 > /sys/kernel/debug/nvme0/fault_inject/probability
# echo 1 > /sys/kernel/debug/nvme0/fault_inject/times
# echo 10 > /sys/kernel/debug/nvme0/fault_inject/space
# nvme reset /dev/nvme0
# dmesg
...
nvme nvme0: Could not set queue count (16385)
nvme nvme0: IO queues not created
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currenlty fault injection support for nvme only enables to inject errors
into the commands submitted to I/O queues.
In preparation for fault injection into the admin commands, this makes
the helper functions independent of struct nvme_ns.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Future use intends to make use of both, so export these functions. And
since their implementation is identical except for the opcode, provide a
new function that implement both.
[akinobu.mita@gmail.com>: fix line over 80 characters]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A controller with multiple namespaces may have multiple request_queues with
their own timeout work. If a controller fails with IO outstanding to
diffent namespaces, each request queue may attempt to handle it, so
ensure there is no previously scheduled timeout work executing prior to
starting controller initialization by synchronizing with each queue.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Qemu started out with a broken implementation of Write Zeroes written
by yours truly. Disable Write Zeroes on qemu for now, eventually
we need to go back and make all the qemu quirks version specific,
but that is left for another time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Since nvme_delete_ctrl_sync() is not called from any other kernel module,
unexport it.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Implement a simple round-robin I/O policy for multipathing. Path
selection is done in two rounds, first iterating across all optimized
paths, and if that doesn't return any valid paths, iterate over all
optimized and non-optimized paths. If no paths are found, use the
existing algorithm. Also add a sysfs attribute 'iopolicy' to switch
between the current NUMA-aware I/O policy and the 'round-robin' I/O
policy.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxgqNUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwsoH+OVXu0NQofwTvVru
8lgF3BSDG2mhf7mxbBBlBizGVy9jnjRNGCFMC+Jq8IwiFLwprja/G27kaDTkpuF1
PHC3yfjKvjTeUP5aNdHlmxv6j1sSJfZl0y46DQal4UeTG/Giq8TFTi+Tbz7Wb/WV
yCx4Lr8okAwTuNhnL8ojUCVIpd3c8QsyR9v6nEQ14Mj+MvEbokyTkMJV0bzOrM38
JOB+/X1XY4JPZ6o3MoXrBca3bxbAJzMneq+9CWw1U5eiIG3msg4a+Ua3++RQMDNr
8BP0yCZ6wo32S8uu0PI6HrZaBnLYi5g9Wh7Q7yc0mn1Uh1zWFykA6TtqK90agJeR
A6Ktjw==
=scY4
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc6' into for-5.1/block
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
If a controller supports the NS Change Notification, the namespace
scan_work is automatically triggered after attaching a new namespace.
Occasionally the namespace scan_work may append the new namespace to the
list before the admin command effects handling is completed. The effects
handling unfreezes namespaces, but if it unfreezes the newly attached
namespace, its request_queue freeze depth will be off and we'll hit the
warning in blk_mq_unfreeze_queue().
On the next namespace add, we will fail to freeze that queue due to the
previous bad accounting and deadlock waiting for frozen.
Fix that by preventing scan work from altering the namespace list while
command effects handling needs to pair freeze with unfreeze.
Reported-by: Wen Xiong <wenxiong@us.ibm.com>
Tested-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is used now just to flush error recovery and reconnect work items in
the RDMA and TCP transports, which can simply be moved to the
corresponding teardown routines.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If a device provides an NQN it is expected to be globally unique.
Unfortunately some firmware revisions for Intel 760p/Pro 7600p devices did
not satisfy this requirement. In these circumstances if a system has >1
affected device then only one device is enabled. If this quirk is enabled
then the device supplied subnqn is ignored and we fallback to generating
one as if the field was empty. In this case we also suppress the version
check so we don't print a warning when the quirk is enabled.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: James Dingwall <james@dingwall.me.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pass poll bool to indicate that we need it to poll. This prepares us for
polling support in nvmf since connect is an I/O that will be queued
and has to be polled in order to complete. If poll is passed,
we call nvme_execute_rq_polled which sends the requests and polls
for its completion.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When boxes are run near (or to) OOM, we have a problem with the discard
page allocation in nvme. If we fail allocating the special page, we
return busy, and it'll get retried. But since ordering is honored for
dispatch requests, we can keep retrying this same IO and failing. Behind
that IO could be requests that want to free memory, but they never get
the chance.
Allocate a fixed discard page per controller for a safe fallback, and use
that if the initial allocation fails.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add __exit annotation to cleanup helper which is only
called once in the module.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the geometry of an OCSSD is enumerated using a two step
approach:
First, nvm_register is called, the OCSSD identify command is issued,
and second the geometry sos and csecs values are read either from the
OCSSD identify if it is a 1.2 drive, or from the NVMe namespace data
structure if it is a 2.0 device.
This patch recombines it into a single step, such that nvm_register can
use the csecs and sos fields independent of which version is used. This
enables one to dynamically size the lightnvm subsystem dma pool.
Reviewed-by: Igor Konopko <igor.j.konopko@intel.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A controller may have an internal state that is not able to successfully
process commands for a short duration. In such states, an immediate
command requeue is expected to fail. The driver may exceed its max
retry count, which permanently ends the command in failure when the same
command would succeed after waiting for the controller to be ready.
NVMe ratified TP 4033 provides a delay hint in the completion status
code for failed commands. Implement the retry delay based on the command
completion status and the controller's requested delay.
Note that requeued commands are handled per request_queue, not per
individual request. If multiple commands fail, the controller should
consistently report the desired delay time for retryable commands in
all CQEs, otherwise the requeue list may be kicked too soon.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the controller supports traffic based keep alive, we restart the keep
alive timer if any admin or io commands was completed during the kato
period. This prevents a possible starvation of keep alive commands in
the presence of heavy traffic as in such case, we already have a health
indication from the host perspective.
Only set a comp_seen indicator in case the controller supports keep
alive to minimize the overhead for pci controllers.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We get the controller attributes in identify, cache them as we'll need
them for traffic based keep alive support.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of directly poking into the struct device add a new numa_node
field to struct nvme_ctrl. This allows fabrics drivers where ctrl->dev
is a virtual device to support NUMA affinity as well.
Also expose the field as a sysfs attribute, and populate it for the
RDMA and FC transports.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwEZdIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAlQH/19oax2Za3IPqF4X
DM3lal5M6zlUVkoYstqzpbR3MqUwgEnMfvoeMDC6mI9N4/+r2LkV7cRR8HzqQCCS
jDfD69IzRGb52VSeJmbOrkxBWsR1Nn0t4Z3rEeLPxwaOoNpRc8H973MbAQ2FKMpY
S4Y3jIK1dNiRRxdh52NupVkQF+djAUwkBuVk/rrvRJmTDij4la03cuCDAO+Di9lt
GHlVvygKw2SJhDR+z3ArwZNmE0ceCcE6+W7zPHzj2KeWuKrZg22kfUD454f2YEIw
FG0hu9qecgtpYCkLSm2vr4jQzmpsDoyq3ZfwhjGrP4qtvPC3Db3vL3dbQnkzUcJu
JtwhVCE=
=O1q1
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc5' into for-4.21/block
Pull in v4.20-rc5, solving a conflict we'll otherwise get in aio.c and
also getting the merge fix that went into mainline that users are
hitting testing for-4.21/block and/or for-next.
* tag 'v4.20-rc5': (664 commits)
Linux 4.20-rc5
PCI: Fix incorrect value returned from pcie_get_speed_cap()
MAINTAINERS: Update linux-mips mailing list address
ocfs2: fix potential use after free
mm/khugepaged: fix the xas_create_range() error path
mm/khugepaged: collapse_shmem() do not crash on Compound
mm/khugepaged: collapse_shmem() without freezing new_page
mm/khugepaged: minor reorderings in collapse_shmem()
mm/khugepaged: collapse_shmem() remember to clear holes
mm/khugepaged: fix crashes due to misaccounted holes
mm/khugepaged: collapse_shmem() stop if punched or truncated
mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
mm/huge_memory: splitting set mapping+index before unfreeze
mm/huge_memory: rename freeze_page() to unmap_page()
initramfs: clean old path before creating a hardlink
kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
psi: make disabling/enabling easier for vendor kernels
proc: fixup map_files test on arm
debugobjects: avoid recursive calls with kmemleak
userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
...
Without CONFIG_NVME_MULTIPATH enabled a multi-port subsystem might
show up as invididual devices and cause problems, warn about it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
We have this functionality in sbitmap, but we don't export it in
blk-mq for users of the tags busy iteration. This can be useful
for stopping the iteration, if the caller doesn't need to find
more requests.
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
For P2P requests, we must use the pci_p2pmem_map_sg() function instead of
the dma_map_sg functions.
With that, we can then indicate PCI_P2P support in the request queue. For
this, we create an NVME_F_PCI_P2P flag which tells the core to set
QUEUE_FLAG_PCI_P2P in the request queue.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Make current_path an array with an entry for every possible node, and
cache the best path on a per-node basis. Take the node distance into
account when selecting it. This is primarily useful for dual-ported PCIe
devices which are connected to PCIe root ports on different sockets.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
We should be registering the ns_id attribute as default sysfs
attribute groups, otherwise we have a race condition between
the uevent and the attributes appearing in sysfs.
Suggested-by: Bart van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe changes from Christoph:
"This contains the support for TP4004, Asymmetric Namespace Access,
which makes NVMe multipathing usable in practice."
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvmet: use Retain Async Event bit to clear AEN
nvmet: support configuring ANA groups
nvmet: add minimal ANA support
nvmet: track and limit the number of namespaces per subsystem
nvmet: keep a port pointer in nvmet_ctrl
nvme: add ANA support
nvme: remove nvme_req_needs_failover
nvme: simplify the API for getting log pages
nvme.h: add ANA definitions
nvme.h: add support for the log specific field
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also moved the logic of the remapping to the nvme core driver instead
of implementing it in the nvme pci driver. This way all the other nvme
transport drivers will benefit from it (in case they'll implement metadata
support).
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add support for Asynchronous Namespace Access as specified in NVMe 1.3
TP 4004. With ANA each namespace attached to a controller belongs to an
ANA group that describes the characteristics of accessing the namespaces
through this controller. In the optimized and non-optimized states
namespaces can be accessed regularly, although in a multi-pathing
environment we should always prefer to access a namespace through a
controller where an optimized relationship exists. Namespaces in
Inaccessible, Permanent-Loss or Change state for a given controller
should not be accessed.
The states are updated through reading the ANA log page, which is read
once during controller initialization, whenever the ANA change notice
AEN is received, or when one of the ANA specific status codes that
signal a state change is received on a command.
The ANA state is kept in the nvme_ns structure, which makes the checks in
the fast path very simple. Updating the ANA state when reading the log
page is also very simple, the only downside is that finding the initial
ANA state when scanning for namespaces is a bit cumbersome.
The gendisk for a ns_head is only registered once a live path for it
exists. Without that the kernel would hang during partition scanning.
Includes fixes and improvements from Hannes Reinecke.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Now that we just call out to blk_path_error there isn't really any good
reason to not merge it into the only caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Merge nvme_get_log and nvme_get_log_ext into a single helper, which takes
a plain nsid instead of the nvme_ns pointer. Also add support for the
log specific field while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
We can not match a command to its completion based on the command
id alone. We need the submitting queue identifier to pair with the
completion, so this patch adds that to the trace buffer.
This patch is also collapsing the admin and IO submission traces into a
single one so we don't need to duplicate this and creating unnecessary
code branches: we know if the command is an admin vs IO based on the qid.
And since we're here, the patch fixes code formatting in the area.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
[hch: move the qid helper to nvme.h and made it an inline function]
Signed-off-by: Christoph Hellwig <hch@lst.de>
We will need to reference the controller in the setup and completion
time for tracing and future traffic based keep alive support.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme requires an sg table allocation for each request. If the request
is large, then the allocation can become quite large. For instance,
with our default software settings of 1280KB IO size, we'll need
10248 bytes of sg table. That turns into a 2nd order allocation,
which we can't always guarantee. If we fail the allocation, blk-mq
will retry it later. But there's no guarantee that we'll EVER be
able to allocate that much contigious memory.
Limit the IO size such that we never need more than a single page
of memory. That's a lot faster and more reliable. Then back that
allocation with a mempool, so that we know we'll always be able
to succeed the allocation at some point.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The problem here is that set_bit() and test_bit() take a bit number so
we should be passing 0 but instead we're passing (1 << 0) which leads to
a double shift. It doesn't cause a runtime bug in the current code
because it's done consistently and we only set that one bit.
I decided to just re-use NVME_AER_NOTICE_NS_CHANGED instead of
introducing a new define for this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
Per section 5.2 we need to issue the corresponding log page to clear an
AEN, so for a namespace data changed AEN we need to read the changed
namespace list log. And once we read that log anyway we might as well
use it to optimize the rescan.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
And move it toward the top of the file to avoid a forward declaration.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
We should register for AEN events; some law-abiding targets might
not be sending us AENs otherwise.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: slight cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
When running blktest's nvme/005 with a lockdep enabled kernel the test
case fails due to the following lockdep splat in dmesg:
=============================
WARNING: suspicious RCU usage
4.17.0-rc5 #881 Not tainted
-----------------------------
drivers/nvme/host/nvme.h:457 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
3 locks held by kworker/u32:5/1102:
#0: (ptrval) ((wq_completion)"nvme-wq"){+.+.}, at: process_one_work+0x152/0x5c0
#1: (ptrval) ((work_completion)(&ctrl->scan_work)){+.+.}, at: process_one_work+0x152/0x5c0
#2: (ptrval) (&subsys->lock#2){+.+.}, at: nvme_ns_remove+0x43/0x1c0 [nvme_core]
The only caller of nvme_mpath_clear_current_path() is nvme_ns_remove()
which holds the subsys lock so it's likely a false positive, but when
using rcu_access_pointer(), we're telling rcu and lockdep that we're
only after the pointer falue.
Fixes: 32acab3181 ("nvme: implement multipath access to nvme subsystems")
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Pull NVMe changes from Keith:
"This is just the first nvme pull request for 4.18. There are several
fabrics and target patches that I missed, so there will be more to
come."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme-pci: drop IRQ disabling on submission queue lock
nvme-pci: split the nvme queue lock into submission and completion locks
nvme-pci: handle completions outside of the queue lock
nvme-pci: move ->cq_vector == -1 check outside of ->q_lock
nvme-pci: remove cq check after submission
nvme-pci: simplify nvme_cqe_valid
nvme: mark the result argument to nvme_complete_async_event volatile
nvme/pci: Sync controller reset for AER slot_reset
nvme/pci: Hold controller reference during async probe
nvme: only reconfigure discard if necessary
nvme/pci: Use async_schedule for initial reset work
nvme: lightnvm: add granby support
NVMe: Add Quirk Delay before CHK RDY for Seagate Nytro Flash Storage
nvme: change order of qid and cmdid in completion trace
nvme: fc: provide a descriptive error
Some P3100 drives have a bug where they think WRRU (weighted round robin)
is always enabled, even though the host doesn't set it. Since they think
it's enabled, they also look at the submission queue creation priority. We
used to set that to MEDIUM by default, but that was removed in commit
81c1cd9835. This causes various issues on that drive. Add a quirk to
still set MEDIUM priority for that controller.
Fixes: 81c1cd9835 ("nvme/pci: Don't set reserved SQ create flags")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Keith Busch <keith.busch@intel.com>
When CONFIG_NVME_MULTIPATH is set, but we're not using nvme to multipath,
namespaces with multiple paths were not creating unique names due to
reusing the same instance number from the namespace's head.
This patch fixes this by falling back to the non-multipath naming method
when the parameter disabled using multipath.
Reported-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nvmf_check_if_ready() checks that were added are very simplistic.
As such, the routine allows a lot of cases to fail ios during windows
of reset or re-connection. In cases where there are not multi-path
options present, the error goes back to the callee - the filesystem
or application. Not good.
The common routine was rewritten and calling syntax slightly expanded
so that per-transport is_ready routines don't need to be present.
The transports now call the routine directly. The routine is now a
fabrics routine rather than an inline function.
The routine now looks at controller state to decide the action to
take. Some states mandate io failure. Others define the condition where
a command can be accepted. When the decision is unclear, a generic
queue-or-reject check is made to look for failfast or multipath ios and
only fails the io if it is so marked. Otherwise, the io will be queued
and wait for the controller state to resolve.
Admin commands issued via ioctl share a live admin queue with commands
from the transport for controller init. The ioctls could be intermixed
with the initialization commands. It's possible for the ioctl cmd to
be issued prior to the controller being enabled. To block this, the
ioctl admin commands need to be distinguished from admin commands used
for controller init. Added a USERCMD nvme_req(req)->rq_flags bit to
reflect this division and set it on ioctls requests. As the
nvmf_check_if_ready() routine is called prior to nvme_setup_cmd(),
ensure that commands allocated by the ioctl path (actually anything
in core.c) preps the nvme_req(req) before starting the io. This will
preserve the USERCMD flag during execution and/or retry.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.e>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvme_start_keep_alive() isn't used outside core.c so unexport it and
make it static.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Compiling on 32 bits system produces a warning for the shift width
when shifting 32 bit integer with 64bit integer.
Make sure that offset always is 64bit, and use macros for retrieving
lower and upper bits of the offset.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
The nvme driver sets up the size of the nvme namespace in two steps.
First it initializes the device with standard logical block and
metadata sizes, and then sets the correct logical block and metadata
size. Due to the OCSSD 2.0 specification relies on the namespace to
expose these sizes for correct initialization, let it be updated
appropriately on the LightNVM side as well.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Enable the lightnvm integration to use the nvme_get_log_ext()
function.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For consistancy reasons, any fabric-specific works
(e.g error recovery/reconnect) should be canceled in
nvme_stop_ctrl, as for all other NVMe pending works
(e.g. scan, keep alive).
The patch aims to simplify the logic of the code, as
we now only rely on a vague demand from any fabric
to flush its private workqueues at the beginning of
.delete_ctrl op.
Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
namespaces_mutext is used to synchronize the operations on ctrl
namespaces list. Most of the time, it is a read operation.
On the other hand, there are many interfaces in nvme core that
need this lock, such as nvme_wait_freeze, and even more interfaces
will be added. If we use mutex here, circular dependency could be
introduced easily. For example:
context A context B
nvme_xxx nvme_xxx
hold namespaces_mutext require namespaces_mutext
sync context B
So it is better to change it from mutex to rwsem.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linux's fault injection framework provides a systematic way to support
error injection via debugfs in the /sys/kernel/debug directory. This
patch uses the framework to add error injection to NVMe driver. The
fault injection source code is stored in a separate file and only linked
if CONFIG_FAULT_INJECTION_DEBUG_FS kernel config is selected.
Once the error injection is enabled, NVME_SC_INVALID_OPCODE with no
retry will be injected into the nvme_end_request. Users can change
the default status code and no retry flag via debufs. Following example
shows how to enable and inject an error. For more examples, refer to
Documentation/fault-injection/nvme-fault-injection.txt
How to enable nvme fault injection:
First, enable CONFIG_FAULT_INJECTION_DEBUG_FS kernel config,
recompile the kernel. After booting up the kernel, do the
following.
How to inject an error:
mount /dev/nvme0n1 /mnt
echo 1 > /sys/kernel/debug/nvme0n1/fault_inject/times
echo 100 > /sys/kernel/debug/nvme0n1/fault_inject/probability
cp a.file /mnt
Expected Result:
cp: cannot stat ‘/mnt/a.file’: Input/output error
Message from dmesg:
FAULT_INJECTION: forcing a failure.
name fault_inject, interval 1, probability 100, space 0, times 1
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.15.0-rc8+ #2
Hardware name: innotek GmbH VirtualBox/VirtualBox,
BIOS VirtualBox 12/01/2006
Call Trace:
<IRQ>
dump_stack+0x5c/0x7d
should_fail+0x148/0x170
nvme_should_fail+0x2f/0x50 [nvme_core]
nvme_process_cq+0xe7/0x1d0 [nvme]
nvme_irq+0x1e/0x40 [nvme]
__handle_irq_event_percpu+0x3a/0x190
handle_irq_event_percpu+0x30/0x70
handle_irq_event+0x36/0x60
handle_fasteoi_irq+0x78/0x120
handle_irq+0xa7/0x130
? tick_irq_enter+0xa8/0xc0
do_IRQ+0x43/0xc0
common_interrupt+0xa2/0xa2
</IRQ>
RIP: 0010:native_safe_halt+0x2/0x10
RSP: 0018:ffffffff82003e90 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffdd
RAX: ffffffff817a10c0 RBX: ffffffff82012480 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 000000008e38ce64 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff82012480
R13: ffffffff82012480 R14: 0000000000000000 R15: 0000000000000000
? __sched_text_end+0x4/0x4
default_idle+0x18/0xf0
do_idle+0x150/0x1d0
cpu_startup_entry+0x6f/0x80
start_kernel+0x4c4/0x4e4
? set_init_arg+0x55/0x55
secondary_startup_64+0xa5/0xb0
print_req_error: I/O error, dev nvme0n1, sector 9240
EXT4-fs error (device nvme0n1): ext4_find_entry:1436:
inode #2: comm cp: reading directory lblock 0
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Reviewed-by: Eric Saint-Etienne <eric.saint.etienne@oracle.com>
Signed-off-by: Karl Volz <karl.volz@oracle.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit e9a48034d7.
The slaves and holders link for the hidden gendisks confuse lsblk so that
it errors out on, or doesn't report the nvme multipath devices. Given
that we don't need holder relationships for something that can't even be
directly accessed we should just stop creating those links.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Potnuri Bharat Teja <bharat@chelsio.com>
Cc: stable@vger.kernel.org
Signed-off-by: Keith Busch <keith.busch@intel.com>
In nvme_keep_alive() we pass a request with a pointer to an NVMe command on
the stack into blk_execute_rq_nowait(). However, the block layer doesn't
guarantee that the request is fully queued before blk_execute_rq_nowait()
returns. If not, and the request is queued after nvme_keep_alive() returns,
then we'll end up using stack memory that might have been overwritten to
form the NVMe command we pass to hardware.
Fix this by keeping a special command struct in the nvme_ctrl struct right
next to the delayed work struct used for keep-alives.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
In pci transport, this state is used to mark the initialization
process. This should be also used in other transports as well.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
This removes nvme multipath's specific status decoding to see if failover
is needed, using the generic blk_status_t that was decoded earlier. This
abstraction from the raw NVMe status means all status decoding exists
in one place.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When the io queues setup or tagset allocation failed, ctrl.tagset is
NULL. But the scan work will still be queued and executed, then panic
comes up due to NULL pointer reference of ctrl.tagset.
To fix this, add a new ctrl state NVME_CTRL_ADMIN_ONLY to inidcate only
admin queue is live. When non io queues or tagset allocation failed, ctrl
enters into this state, scan work will not be started. But async event
work and nvme dev ioctl will be still available. This will be helpful to
do further investigation and recovery.
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In case our last path is removed during traffic, we can end up requeueing
the bio(s) but never schedule the actual requeue work as upper layers
still have open handles on the mpath device node.
Fix this by scheduling requeue work if the namespace being removed is
the last path in the ns_head path list.
Fixes: 32acab3181 ("nvme: implement multipath access to nvme subsystems")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
And increase the existing delay to cover this device as well.
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Lien <jeff.lien@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When creating nvme multipath devices we should populate the 'slaves' and
'holders' directorys properly to aid userspace topology detection.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: split from a larger patch, compile fix for CONFIG_NVME_MULTIPATH=n]
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We do this by adding a helper that returns the ns_head for a device that
can belong to either the per-controller or per-subsystem block device
nodes, and otherwise reuse all the existing code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch adds native multipath support to the nvme driver. For each
namespace we create only single block device node, which can be used
to access that namespace through any of the controllers that refer to it.
The gendisk for each controllers path to the name space still exists
inside the kernel, but is hidden from userspace. The character device
nodes are still available on a per-controller basis. A new link from
the sysfs directory for the subsystem allows to find all controllers
for a given subsystem.
Currently we will always send I/O to the first available path, this will
be changed once the NVMe Asynchronous Namespace Access (ANA) TP is
ratified and implemented, at which point we will look at the ANA state
for each namespace. Another possibility that was prototyped is to
use the path that is closes to the submitting NUMA code, which will be
mostly interesting for PCI, but might also be useful for RDMA or FC
transports in the future. There is not plan to implement round robin
or I/O service time path selectors, as those are not scalable with
the performance rates provided by NVMe.
The multipath device will go away once all paths to it disappear,
any delay to keep it alive needs to be implemented at the controller
level.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce a new struct nvme_ns_head that holds information about an actual
namespace, unlike struct nvme_ns, which only holds the per-controller
namespace information. For private namespaces there is a 1:1 relation of
the two, but for shared namespaces this lets us discover all the paths to
it. For now only the identifiers are moved to the new structure, but most
of the information in struct nvme_ns should eventually move over.
To allow lockless path lookup the list of nvme_ns structures per
nvme_ns_head is protected by SRCU, which requires freeing the nvme_ns
structure through call_srcu.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This allows us to manage the various uniqueue namespace identifiers
together instead needing various variables and arguments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This adds a new nvme_subsystem structure so that we can track multiple
controllers that belong to a single subsystem. For now we only use it
to store the NQN, and to check that we don't have duplicate NQNs unless
the involved subsystems support multiple controllers.
Includes code originally from Hannes Reinecke to expose the subsystems
in sysfs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Several block layer and NVMe core functions accept a combination
of BLK_MQ_REQ_* flags through the 'flags' argument but there is
no verification at compile time whether the right type of block
layer flags is passed. Make it possible for sparse to verify this.
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: linux-nvme@lists.infradead.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will give udev a chance to observe and handle asynchronous event
notifications and clear the log to unmask future events of the same type.
The driver will create a change uevent of the asyncronuos event result
before submitting the next AEN request to the device if a completed AEN
event is of type error, smart, command set or vendor specific,
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Async event work is for core use only and should not be called directly
from drivers.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The driver can handle tracking only one AEN request, so this patch
removes handling for multiple ones.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All the transports were unnecessarilly duplicating the AEN request
accounting. This patch defines everything in one place.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe standard provides a command effects log page so the host may
be aware of special requirements it may need to do for a particular
command. For example, the command may need to run with IO quiesced to
prevent timeouts or undefined behavior, or it may change the logical block
formats that determine how the host needs to construct future commands.
This patch saves the nvme command effects log page if the controller
supports it, and performs appropriate actions before and after an admin
passthrough command is completed. If the controller does not support the
command effects log page, the driver will define the effects for known
opcodes. The nvme format and santize are the only commands in this patch
with known effects.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the ->delete_work and the associated helpers to common code instead
of duplicating them in every driver. This also adds the missing reference
get/put for the loop driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the core chrdev code to set up the link between the character device
and the nvme controller. This allows us to get rid of the global list
of all controllers, and also ensures that we have both a reference to
the controller and the transport module before the open method of the
character device is called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sgi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Instead of allocating a separate struct device for the character device
handle embedd it into struct nvme_ctrl and use it for the main controller
refcounting. This removes double refcounting and gets us an automatic
reference for the character device operations. We keep ctrl->device as a
pointer for now to avoid chaning printks all over, but in the future we
could look into message printing helpers that take a controller structure
similar to what other subsystems do.
Note the delete_ctrl operation always already has a reference (either
through sysfs due this change, or because every open file on the
/dev/nvme-fabrics node has a refernece) when it is entered now, so we
don't need to do the unless_zero variant there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Move blk_mq_reinit_tagset from blk-mq to nvme core
as the only user of it. Current transports that use
it (rdma, fc) simply implement .reinit_request op.
This patch does not change any functionality.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The underlying blk_mq_tag_set, and request timeout parameters support an
unsigned int. Extend the size of the nvme module parameters for io and
admin commands to match.
Signed-off-by: Marc Olson <marcolso@amazon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Adds support for the new Host Memory Buffer Minimum Descriptor Entry Size
and Host Memory Maximum Descriptors Entries field that were added in
TP 4002 HMB Enhancements. These allow the controller to advertise
limits for the usual number of segments in the host memory buffer, as
well as a minimum usable per-segment size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
nvme_nvm_ns_supported assumes every device is a pci_dev, which leads to
reading an incorrect field, or possible even a dereference of unallocated
memory for fabrics controllers.
Fix this by introducing a quirk for lighnvm capable devices instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
These functions are used only locally in the nvme core.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
And move the flags for the flags field near that field while touching
this area.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
If an NVMe controller reports RTD3 Entry Latency larger than
shutdown_timeout, up to a maximum of 60 seconds, use that value to set
the shutdown timer. Otherwise fall back to the module parameter which
defaults to 5 seconds.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: removed do_div, made transition time local scope]
Signed-off-by: Christoph Hellwig <hch@lst.de>
