Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, TX power is reported on interface/wdev level as
part of NL80211_CMD_GET_INTERFACE. With MLO, Multiple links
can be part of an interface/wdev and hence its necessary to
report the TX power of each link.
Add support to send tx power for all valid links of an MLD as
part of NL80211_CMD_GET_INTERFACE request.
As far as userspace is concerned, there is no behavioral change
for Non-ML Interfaces. For ML interfaces, userspace should fetch
TX power that is nested inside NL80211_ATTR_MLO_LINKS, similar to
how channel info(NL80211_ATTR_WIPHY_FREQ) is fetched.
Co-developed-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20241125083217.216095-2-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, during starting a radar detection, no link id information is
parsed and passed down. In order to support starting radar detection
during Multi Link Operation, it is required to pass link id as well.
Add changes to first parse and then pass link id in the start radar
detection path.
Additionally, update notification APIs to allow drivers/mac80211 to
pass the link ID.
However, everything is handled at link 0 only until all API's are ready to
handle it per link.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the full struct cfg80211_ap_settings for an update is
misleading, since most settings cannot be updated. Split the
update case off into a new struct cfg80211_ap_update.
Change-Id: I3ba4dd9280938ab41252f145227a7005edf327e4
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify the prototype for change_beacon() in struct cfg80211_op to
accept cfg80211_ap_settings instead of cfg80211_beacon_data so that
it can process data in addition to beacons.
Modify the prototypes of ieee80211_change_beacon() and driver specific
functions accordingly.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727174100.11721-4-quic_alokad@quicinc.com
[while at it, remove pointless "if (info)" check in tracing that just
makes all the lines longer than they need be - it's never NULL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The prandom_u32() function has been a deprecated inline wrapper around
get_random_u32() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. The same also applies to get_random_int(), which is
just a wrapper around get_random_u32(). This was done as a basic find
and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> # for sch_cake
Acked-by: Chuck Lever <chuck.lever@oracle.com> # for nfsd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for thunderbolt
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Acked-by: Helge Deller <deller@gmx.de> # for parisc
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220730052643.1959111-4-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove braces around single statement blocks in order to improve
readability. Also, an extra blank line was removed. Both warnings are
reported by checkpatch.pl
Signed-off-by: Sebin Sebastian <mailmesebin00@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220802045305.235684-1-mailmesebin00@gmail.com
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
some function's label meaningless, the return statement follows
the goto statement, so just remove it.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210223065754.34392-1-samirweng1979@163.com
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware supports only STA as primary interface in repeater mode.
Since the only meaningful usage of AP + STA interface combination
is repeater, reject such combination with AP as primary interface.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Quantenna Pearl device exposes multiple (up to 3) radio interfaces under
single PCIe function. So far all the wiphy devices were attached to the
same pcie device. As a result, all different wireless network devices
were reported under the same sysfs directory for pcie device, e.g.:
$ ls /sys/class/net/wlan0/device/net/
wlan0 wlan1
It turns out that such behavior may confuse various users of wireless
subsystem. For instance, it turned out to be the case for:
- Linux init systems, e.g. for renaming based on parent device
- OpenWRT configuration scripts
Suggested solution is to add an intermediate virtual platform device
for each radio interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable WPA3 OWE support in AP mode. Driver currently supports cards that
offload OWE processing to userspace. This patch adds all the required
tools for such offloading. Firmware requests OWE processing sending new
UPDATE_OWE event to driver, which uses cfg80211_update_owe_info_event to
notify userspace software. After OWE processing is completed, userspace
sends calculated IEs to firmware using update_owe_info cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable WPA3 SAE support in AP mode. Driver currently supports cards
that offload SAE authentication to userspace. So allow userspace
software to subscribe and to send AUTH frames. Besides, enable
AP mode support in external_auth cfg80211 callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each radio on a given wifi device may have different max scan SSIDs
limitation, so take this information from a per-radio info structure.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switch to extendable implementation of channel survey dump to make sure
that any new channel statistics can be added in the future without any
backwards compatibility issues. For this purpose use a separate variable
length bitmap to pass the list of valid statistics in firmware response.
Besides, switch to using channel frequency instead of IEEE channel
number to prepare for adding support of 6GHz band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support any number of capabilities bits in the future,
replace u32 capabilities bitmask by array. Pass
capabilities from firmware using TLV element.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware may support DFS offload. However the final decision on whether
to use it or not should be up to the user. So even if firmware supports
DFS offload, it should be enabled only if user explicitly requests it.
For this purpose introduce kernel param dfs_offload which is disabled
by default.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently this parameter is global, it is not specific to mac.
So this function does not need any input parameters.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware reports that it supports hardware switch capabilities,
driver needs to track and notify device whenever broadcast domain
of a particular network device changes (ie. whenever it's upper
master device changes).
Firmware needs a unique ID to tell broadcast domains from each other
which is an opaque number otherwise. For that purpose we can use
netspace:ifidx pair to uniquely identify each broadcast domain:
- if netdev is not part of a bridge, then use it's own ifidx
as a broadcast domain ID
- if netdev is part of a bridge, then use bridge netdev ifidx
as broadcast domain ID
Firmware makes sure that packets are only forwarded between
interfaces marked with the same broadcast domain ID.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in case of error when registering network device with the
kernel, we won't properly cleanup VIF state in firmware due to DEL_VIF
command will not be send to wifi card. Make sure it does.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add new command for getting/setting current transmit power
and propagate requests from user space to firmware.
Signed-off-by: Mikhail Karpenko <mkarpenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ETSI region DFS slave device can operate in two modes on DFS channels:
- do on-channel radar detection and use higher Tx power
- don't do radar detection and use lower Tx power as a consequence
Allow user to control that behavior through qtnfmac module parameter.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use control path to send EAPOL frames to make sure they are
sent with higher priority with aggregation disabled.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allow to change netns for wireless interfaces created by qtnfmac driver.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently driver uses the same regulatory rules to register all wiphy
instances. This is not logically correct since each wiphy may have
different capabilities (different supported bands, EIRP etc).
Allow firmware to pass regulatory rules for each MAC separately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use REGULATORY_CUSTOM_REG flag only if firmware advertised a custom
regulatory domain prior to wiphy registration. Use REGULATORY_STRICT_REG
flag only if firmware knows its regulatory domain.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Error reporting in qtnf_cfg80211_reg_notifier only requires to print
one type of message and an error code. Firmware will report success
for an attempt to set regulatory region to the same value,
so no special handling is required for this case.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless core calls regulatory notifier for each wiphy and it only
guarantees that bands info is updated for this particular wiphy prior
to calling a notifier. Hence updating all wiphy which belong to driver
in a single notifier callback is redundant and incorrect.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of SAE AP, drivers offload authentication to user-space
software, e.g. hostapd. For FullMAC drivers the procedure is as follows.
If auth_type is SAE and user space indicates external authentication
capability, then driver requests authentication offload to user-space
software using cfg80211_external_auth_request call. From that point,
auth frame exchange is performed transparently for driver: user-space
software sends/receives mgmt frames using mgmt_tx/mgmt_frame_register
cfg80211 callbacks. As soon as authenitcation is completed, user-space
software notifies driver about its status using external_auth cfg80211
callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace textual license with SPDX-License-Identifier.
Add an SPDX-License-Identifier for the Makefile.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not reject RETRY changes in driver. This decision
should belong to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise WIPHY_FLAG_4ADDR_STATION capability to wireless core. Send
use4addr interface change flag to firmware in change_virtual_intf
cfg80211 callback.
In order to enable adding wireless station interface to bridge
one should turn on 4addr mode using the following command:
$ iw dev wlan0 set 4addr on
$ brctl addif br0 wlan0
If this commands succeeds, then interface can be added to bridge.
Note that when wireless interface is added to bridge, wpa_supplicant
should be started with appropriate -b <brname> parameter, e.g:
$ wpa_supplicant -Dnl80211 -iwlan0 -c/path/to/wpa.conf -b br0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation of dump_station cfg80211 callback supports
AP mode only. Add support for STA mode as well: by default in STA
mode this callback is supposed to return AP on managed interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not cancel scan in disconnect callback. If there is an active scan,
it will be cancelled by firmware, then host driver will be properly
notified by event.
Cancelling scan in disconnect callback occasionally may lead to the
following race issue. Host is able to queue one scan after scan
abort in disconnect callback, and another scan after scan abort
in event handler. As a result, firmware receives second scan
before the first scan completes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unify command error handling using qtnf_cmd_resp_result_decode
function. Do not duplicate error messages in command handlers
and cfg80211 callbacks: report 'cmd exec fail' only on control
path internal failure. Remove redundant 'unlikely' macros.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When cfg80211 disconnect callback is triggered and command is
processed by firmware, disconnect event with local parameter
set must be sent immediately. Indicating that it's a "local"
event (not from AP) will help upper layers to process this
event correctly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove STA connection states tracking from driver.
Leave it wireless core on host and to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c: In function 'qtnf_dump_survey':
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c:694:19: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements basic WoWLAN support in qtnfmac driver, including
processing of WoWLAN features reported by firmware and implementation
of cfg80211 suspend/resume/wakeup callbacks. Currently the following
WoWLAN triggers are supported: disconnect, magic packet,
custom pattern packet.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbVgnkAAoJEG4XJFUm622b/DAH/0wmjFQrt1qe/goZ4igZOC5z
TTqPUmv7HO4PbHV6mU5yOFGsRCaGDo1cTyEeoiaYNGH6bQLzzJZeQORkuPQB2q5S
BCwlaET7F2iSmk8hx7eboONyVDm5v2+g6NMHBoikVFz1wZ13kCVa4sHkokUJKYB9
XNw3B2OiarPv9i37DlY3woMlY+6VMQh8J6GiB9cJSa4Xs+7l1aQCdQRP03SabI71
gLBEsW+bEVZrUdJGB5cZ8c6LmukmRQMDKMTQYUna5ZXeW1IX3ejYcQGHzzCZoKJS
LPUmisz4014r5aBzXIu3ctVn4LnVhMS5ms0EH1A6IX3vx8G9QynqH5lm9VQ1OXI=
=kWW/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
