When compiling with gcc 13.1 and CONFIG_FORTIFY_SOURCE=y,
I've noticed the following:
In function ‘fortify_memcpy_chk’,
inlined from ‘wil_rx_crypto_check_edma’ at drivers/net/wireless/ath/wil6210/txrx_edma.c:566:2:
./include/linux/fortify-string.h:529:25: warning: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Wattribute-warning]
529 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
where the compiler complains on:
const u8 *pn;
...
pn = (u8 *)&st->ext.pn_15_0;
...
memcpy(cc->pn, pn, IEEE80211_GCMP_PN_LEN);
and:
In function ‘fortify_memcpy_chk’,
inlined from ‘wil_rx_crypto_check’ at drivers/net/wireless/ath/wil6210/txrx.c:684:2:
./include/linux/fortify-string.h:529:25: warning: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Wattribute-warning]
529 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
where the compiler complains on:
const u8 *pn = (u8 *)&d->mac.pn_15_0;
...
memcpy(cc->pn, pn, IEEE80211_GCMP_PN_LEN);
In both cases, the fortification logic interprets 'memcpy()' as 6-byte
overread of 2-byte field 'pn_15_0' of 'struct wil_rx_status_extension'
and 'pn_15_0' of 'struct vring_rx_mac', respectively. To silence
these warnings, last two fields of the aforementioned structures
are grouped using 'struct_group_attr(pn, __packed' quirk.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230621093711.80118-1-dmantipov@yandex.ru
FW reports Tx/Rx extended MCS 12.1 to driver as "26". Driver will
convert this into base MCS 7 + EXTENDED_SC_DMG flag so kernel can do
the correct phy rate conversion. Also add log prints to print "12.1"
instead of "26" for extended MCS.
Signed-off-by: Max Chen <mxchen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1609977050-7089-3-git-send-email-mxchen@codeaurora.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'wil' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'ring' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'i' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1161: warning: Function parameter or member 'wil' not described in 'wil_tx_sring_handler'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1161: warning: Function parameter or member 'sring' not described in 'wil_tx_sring_handler'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'd' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'tso_desc_type' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'is_ipv4' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'tcp_hdr_len' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'skb_net_hdr_len' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'mss' not described in 'wil_tx_desc_offload_setup_tso_edma'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073545.GU3248864@dell
Dump all the Rx status message on different errors to allow more
visibility of the case.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a check on the retry counter invalid_buf_id_retry that is always
false because invalid_buf_id_retry is initialized to zero on each iteration
of a while-loop. Fix this by initializing the retry counter before the
while-loop starts.
Addresses-Coverity: ("Logically dead code")
Fixes: b4a967b7d0 ("wil6210: reset buff id in status message after completion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change all files to add SPDX license identifiers and
remove license text.
This is only an administrative change, there is no change
in actual license or copyright for any file.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The short frame check in wil_sring_reap_rx_edma uses
skb->len which store the maximum frame length. Fix
this to use dmalen which is the actual length of
the received frame.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to compiler optimization, it's possible that dr_bit (descriptor
ready) is read last from the status message.
Due to race condition between HW writing the status message and
driver reading it, other fields that were read earlier (before dr_bit)
could have invalid values.
Fix this by explicitly reading the dr_bit first and then using rmb
before reading the rest of the status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11.
wil6210 reports it's EDMG capabilities (that are also based on FW
capability) to cfg80211 by filling
wiphy->bands[NL80211_BAND_60GHZ]->edmg_cap.
wil6210 handles edmg.channels and edmg.bw_config requested in connect
and start_ap operations.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver updates Tx status ring HW tail only after it finishes
processing the whole status ring, while the HW is still transmitting
from other transmit rings. This can cause back-pressure on HW if
no status entries are available.
Update HW tail of Tx status ring without waiting for the end of the
processing to help feeding back the HW with status entries and to allow
additional packet transmission.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure rx_buff_mgmt is initialized before accessing it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Save the parameter of max_assoc_sta per device.
On fw_ready event calculate the max_assoc_sta and save it per device,
do not overwrite the max_assoc_sta module param.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since DR bit and buffer id are written in different dwords of
the status message, the DR bit can already be set to 1 while the
buffer id is not updated yet.
Resetting the buffer id in the status message will allow the driver
to identify such cases and re-read the status message until the buffer
id is written by HW.
In case DR bit is set but buffer id is zero, need to read the status
message again, until a valid id is identified.
In addition to that, move the completed buffer id to the tail of the
free list to prevent its immediate reuse in the upcoming refill.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update the rx packet checksum of received packet according to edma
HW spec:
No need to calculate checksum in the following cases:
L4_status=0 and L3_status=0 - No L3 and no L4 known protocols found
L4_status=0 and L3_status=1 - L3 was found, and checksum check passed.
No known L4 protocol was found.
L4_status=1 - L4 was found, and checksum check passed.
Recalculate checksum in the following cases:
L4_status=3 and L3_status=1 - It means that L3 protocol was found,
and checksum passed, but L4 checksum failed.
L4_status=3 and L3_status=2 - Both L3 and L4 checksum check failed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
edma_rx_swtail dma memory free is missing.
Add this part of Rx desc ring free.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon status ring handling, in case there are both unicast and
multicast (cid == max) status messages to handle, wrong sta statistics
might get updated.
Fix this by setting stats to NULL upon invalid cid
(e.g. == max_assoc_sta).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
After being associated with some EDMA rx traffic, upon "down" driver
doesn't free all skbs in the rx ring.
Modify wil_move_all_rx_buff_to_free_list to loop on active list of rx
buffers, unmap the physical memory and free the skb.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx buffers in EDMA mode are initialized to 4 bytes aligned size.
Remove the unnecessary alignment code applied on rx buffer size.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
L2 RX status errors should not be treated as a bitmap and the actual
error values should be checked.
Print L2 errors as wil_err_ratelimited for easier debugging
when such errors occurs.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When enlarging rx_ring_order module param, wil6210 fails to load
because there are not enough Rx buffers.
Fix this by enlarging number of Rx buffers at startup, if needed based
on rx_ring_order.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In Talyn-MB, the 11ad throughput is higher and performance drops
may occur in the current RX configuration due to unavailability
of Rx buffers.
Increase the RX descriptor ring, RX status ring and number of RX
buffers to stabilize the performance in high throughput.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This feature is needed for enterprise APs and clients to enable
fast roaming as defined in 802.11r between APs in the same ESS.
On AP side, this feature is supported only when disable_ap_sme
is enabled.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HW requires Rx buffers to be 4 bytes aligned. Modify the driver to
meet this requirement.
Enable OFU rdy valid bug fix, to prevent hang in oful34_rx while
there is back-pressure from host during RX.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver sets CHECKSUM_UNNECESSARY only in case the HW
doesn't report checksum error.
As ip_summed value is not initialized it is not clear what
the driver will report to the network stack in case of HW checksum
error or in case HW doesn't calculate checksum.
Initialize ip_summed to CHECKSUM_NONE to guarantee checksum
calculation by the network stack in the above cases.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collect statistics of TX latency. The latency is measured from the time
the HW gets aware of new SKB to transmit until the HW indicates tx
complete for this SKB.
The statistics are shown via new "tx_latency" debugfs.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to recent change in FW, driver will be notified of corrupted Rx
packets (e.g. MIC error).
Drop such packets before they are delivered to network stack.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Store the last received multicast sequence number (SN) part of the TID
info. Drop Rx multicast packets with retry bit set which their SN
is equal to the last received.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enhanced DMA RX data path is handled using a single
RX descriptor ring for all VIFs.
Multiple RX status rings are supported, to allow RSS
and multi MSI support.
The driver gets the RX completions via the RX status rings.
The RX status message includes the completed RX buffer ID,
which points to the allocated SKB.
The enhanced DMA RX data flow supports RX chaining, where
multiple SKBs are merged into a single packet.
Enhanced DMA HW supports RX HW reorder offload, enabled by
default for Talyn-MB.
amsdu_en debugfs entry was added to allow control MSDU aggregation.
Use the following command to disable AMSDU (enabled by default):
echo 0 > amsdu_en
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enhanced DMA TX data path is handled using a descriptor
ring per connection and a single status ring.
The driver gets TX completions via the TX status ring. Each
status message points to the completed descriptor ring and
includes the number of completed descriptors in this ring.
Non TSO enhanced DMA TX descriptors are similar to legacy DMA
TX descriptors, hence the same transmit function can be used.
However, enhanced DMA TSO frames division is performed by the
HW, hence a new function is added to handle enhanced DMA TSO.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enhanced DMA design includes the following rings:
- Single RX descriptor ring is used for all VIFs
- Multiple RX status rings are supported, to allow RSS
- TX descriptor ring is allocated per connection
- A single TX status ring is used for all TX descriptor rings
This patch initializes and frees the above descriptor and
status rings.
The RX SKBs are handled by a new entity of RX buffers manager,
which handles RX buffers, each one points to an allocated SKB.
During Rx completion processing, the driver extracts a buffer
ID which is used as an index to the buffers array.
After the SKB is freed the buffer is moved from the 'active'
list to the 'free' list, indicating it can be used for another
descriptor. During Rx refill, SKBs are allocated and attached
to 'free' buffers. Those buffers are attached to new descriptors
and moved to the 'active' list.
New debugfs entries were added to allow edma configuration:
Run the following command to configure the number of status rings:
echo NUM_OF_STATUS_RINGS > num_rx_status_rings
Run the following command to use extended RX status message for
additional debug fields from HW:
echo 0 > compressed_rx_status
Run the following command to control the size of the TX status ring:
echo TX_STATUS_RING_ORDER > tx_status_ring_order
The status ring size will be 1 << tx_status_ring_order
Run the following command to control the size of the RX status ring:
echo RX_STATUS_RING_ORDER > rx_status_ring_order
Due to HW constrains RX sring order should be bigger than RX ring order
The status ring size will be 1 << rx_status_ring_order
Run the following command to change the number of RX buffer IDs:
echo RX_BUFF_ID_COUNT > rx_buff_id_count
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
