Only a handful of PHY drivers needs the PHY package functionality,
therefore build the module only if needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/42c05496-61b2-4b09-b853-3d99b3dfe95c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the MaxLinear MxL86110 Gigabit Ethernet PHY, a low-power,
cost-optimized transceiver supporting 10/100/1000 Mbps over twisted-pair
copper, compliant with IEEE 802.3.
The driver implements basic features such as:
- Device initialization
- RGMII interface timing configuration
- Wake-on-LAN support
- LED initialization and control via /sys/class/leds
This driver has been tested on multiple Variscite boards, including:
- VAR-SOM-MX93 (i.MX93)
- VAR-SOM-MX8M-PLUS (i.MX8MP)
Example boot log showing driver probe:
[ 7.692101] imx-dwmac 428a0000.ethernet eth0:
PHY [stmmac-0:00] driver [MXL86110 Gigabit Ethernet] (irq=POLL)
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250521212821.593057-1-stefano.radaelli21@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for Aeonsemi AS21xxx 10G C45 PHYs. These PHYs integrate
an IPC to setup some configuration and require special handling to
sync with the parity bit. The parity bit is a way the IPC use to
follow correct order of command sent.
Supported PHYs AS21011JB1, AS21011PB1, AS21010JB1, AS21010PB1,
AS21511JB1, AS21511PB1, AS21510JB1, AS21510PB1, AS21210JB1,
AS21210PB1 that all register with the PHY ID 0x7500 0x7510
before the firmware is loaded.
They all support up to 5 LEDs with various HW mode supported.
While implementing it was found some strange coincidence with using the
same logic for implementing C22 in MMD regs in Broadcom PHYs.
For reference here the AS21xxx PHY name logic:
AS21x1xxB1
^ ^^
| |J: Supports SyncE/PTP
| |P: No SyncE/PTP support
| 1: Supports 2nd Serdes
| 2: Not 2nd Serdes support
0: 10G, 5G, 2.5G
5: 5G, 2.5G
2: 2.5G
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After having factored out the provider part from mdio_bus.c, we can
make the mdio consumer / device layer a separate module. This also
allows to remove Kconfig symbol MDIO_DEVICE.
The module init / exit functions from mdio_bus.c no longer have to be
called from phy_device.c. The link order defined in
drivers/net/phy/Makefile ensures that init / exit functions are called
in the right order.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dba6b156-5748-44ce-b5e2-e8dc2fcee5a7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
MDIO_DEVRES is only set where PHYLIB/PHYLINK are set which
select MDIO_DEVRES. So we can remove this symbol.
Note: Due to circular module dependencies we can't simply
make mdio_devres.c part of phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/27cba535-f507-4b32-84a3-0744c783a465@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/phy/Kconfig is included from drivers/net/Kconfig in an
"if NETDEVICES" section. Therefore we don't have to duplicate the
dependency here. And if e.g. PHYLINK is selected somewhere, then the
dependency is ignored anyway (see note in Kconfig help).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/085892cd-aa11-4c22-bf8a-574a5c6dcd7c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for TJA1121 which is based on TJA1120 but with
additional MACsec IP.
Signed-off-by: Andrei Botila <andrei.botila@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250228154320.2979000-3-andrei.botila@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of adding a source file with hwmon support, move the
Realtek PHY driver to its own subdirectory and rename realtek.c to
realtek_main.c.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/c566551b-c915-4e34-9b33-129a6ddd6e4c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When microchip_t1_phy is built in and phyptp is module
facing undefined reference issue. This get fixed when
microchip_t1_phy made dependent on PTP_1588_CLOCK_OPTIONAL.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501090604.YEoJXCXi-lkp@intel.com
Fixes: fa51199c5f ("net: phy: microchip_rds_ptp : Add rds ptp library for Microchip phys")
Signed-off-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://patch.msgid.link/20250110054424.16807-1-divya.koppera@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add ptp library support in Kconfig
As some of Microchip T1 phys support ptp, add dependency
of 1588 optional flag in Kconfig
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://patch.msgid.link/20241219123311.30213-4-divya.koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Re-organize MediaTek ethernet phy driver files and get ready to integrate
some common functions and add new 2.5G phy driver.
mtk-ge.c: MT7530 Gphy on MT7621 & MT7531 Gphy
mtk-ge-soc.c: Built-in Gphy on MT7981 & Built-in switch Gphy on MT7988
mtk-2p5ge.c: Planned for built-in 2.5G phy on MT7988
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver supports Applied Micro Circuits Corporation QT2025 PHY,
based on a driver for Tehuti Networks TN40xx chips.
The original driver for TN40xx chips supports multiple PHY hardware
(AMCC QT2025, TI TLK10232, Aqrate AQR105, and Marvell 88X3120,
88X3310, and MV88E2010). This driver is extracted from the original
driver and modified to a PHY driver in Rust.
This has been tested with Edimax EN-9320SFP+ 10G network adapter.
Reviewed-by: Trevor Gross <tmgross@umich.edu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce cable testing support for the DP83TG720 PHY. This implementation
is based on the "DP83TG720S-Q1: Configuring for Open Alliance Specification
Compliance (Rev. B)" application note.
The feature has been tested with cables of various lengths:
- No cable: 1m till open reported.
- 5 meter cable: reported properly.
- 20 meter cable: reported as 19m.
- 40 meter cable: reported as cable ok.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240812073046.1728288-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce helper functions specific to Open Alliance diagnostics,
integrating them into the PHY framework. Currently, these helpers
are limited to 1000BaseT1 specific TDR functionality.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240812073046.1728288-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the driver for the Airoha EN8811H 2.5 Gigabit PHY. The phy supports
100/1000/2500 Mbps with auto negotiation only.
The driver uses two firmware files, for which updated versions are added to
linux-firmware already.
Note: At phy-address + 8 there is another device on the mdio bus, that
belongs to the EN881H. While the original driver writes to it, Airoha
has confirmed this is not needed. Therefore, communication with this
device is not included in this driver.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326162305.303598-3-ericwouds@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marvell 88q2xxx devices have an inbuilt temperature sensor. Add hwmon
support for this sensor.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-9-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for addition of other Qcom PHY and to tidy things up,
move the at803x PHY driver to dedicated directory.
The same order in the Kconfig selection is saved.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add MACsec support.
The MACsec block has four TX SCs and four RX SCs. The driver supports up
to four SecY. Each SecY with one TX SC and one RX SC.
The RX SCs can have two keys, key A and key B, written in hardware and
enabled at the same time.
The TX SCs can have two keys written in hardware, but only one can be
active at a given time.
On TX, the SC is selected using the MAC source address. Due of this
selection mechanism, each offloaded netdev must have a unique MAC
address.
On RX, the SC is selected by SCI(found in SecTAG or calculated using MAC
SA), or using RX SC 0 as implicit.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Rust implementation of drivers/net/phy/ax88796b.c. The
features are equivalent. You can choose C or Rust version kernel
configuration.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Reviewed-by: Trevor Gross <tmgross@umich.edu>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds abstractions to implement network PHY drivers; the
driver registration and bindings for some of callback functions in
struct phy_driver and many genphy_ functions.
This feature is enabled with CONFIG_RUST_PHYLIB_ABSTRACTIONS=y.
This patch enables unstable const_maybe_uninit_zeroed feature for
kernel crate to enable unsafe code to handle a constant value with
uninitialized data. With the feature, the abstractions can initialize
a phy_driver structure with zero easily; instead of initializing all
the members by hand. It's supposed to be stable in the not so distant
future.
Link: https://github.com/rust-lang/rust/pull/116218
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83TG720S-Q1 device is an IEEE 802.3bp and Open Alliance compliant
automotive Ethernet physical layer transceiver.
This driver was tested with i.MX8MP EQOS (stmmac) on the MAC side and
same TI PHY on other side.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231212054144.87527-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move aquantia PHY driver to separate driectory in preparation for
firmware loading support to keep things tidy.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microchip LAN8740/LAN8742 PHYs support basic unicast, broadcast, and
Magic Packet WoL. They have one pattern filter matching up to 128 bytes
of frame data, which can be used to implement ARP or multicast WoL.
ARP WoL matches any ARP frame with broadcast address.
Multicast WoL matches any multicast frame.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/1690329270-2873-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a driver for the Marvell 88Q2110. This driver allows to detect the
link, switch between 100BASE-T1 and 1000BASE-T1 and switch between
master and slave mode. Autonegotiation supported by the PHY does not yet
work.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The new phy driver attempts to select a driver from another subsystem,
but that fails when the NVMEM subsystem is disabled:
WARNING: unmet direct dependencies detected for NVMEM_MTK_EFUSE
Depends on [n]: NVMEM [=n] && (ARCH_MEDIATEK [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Selected by [y]:
- MEDIATEK_GE_SOC_PHY [=y] && NETDEVICES [=y] && PHYLIB [=y] && (ARM64 && ARCH_MEDIATEK [=n] || COMPILE_TEST [=y])
I could not see an actual compile time dependency, so presumably this
is only needed for for working correctly but not technically a dependency
on that particular nvmem driver implementation, so it would likely
be safe to remove the select for compile testing.
To keep the spirit of the original 'select', just replace this with a
'depends on' that ensures that the driver will work but does not get in
the way of build testing.
Fixes: 98c485eaf5 ("net: phy: add driver for MediaTek SoC built-in GE PHYs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230616093009.3511692-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some of MediaTek's Filogic SoCs come with built-in gigabit Ethernet
PHYs which require calibration data from the SoC's efuse.
Despite the similar design the driver doesn't share any code with the
existing mediatek-ge.c.
Add support for such PHYs by introducing a new driver with basic
support for MediaTek SoCs MT7981 and MT7988 built-in 1GE PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Microchip LAN865x Rev.B0 10BASE-T1S Internal PHYs
(LAN8650/1). The LAN865x combines a Media Access Controller (MAC) and an
internal 10BASE-T1S Ethernet PHY to access 10BASE‑T1S networks. As
LAN867X and LAN865X are using the same function for the read_status,
rename the function as lan86xx_read_status.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As per AN1699, the initial configuration in the driver applies to LAN867x
Rev.B1 hardware revision. 0x0007C160 (Rev.A0) and 0x0007C161 (Rev.B0)
never released to production and hence they don't need to be supported.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove LAN867X from the driver description as this driver is common for
all the Microchip 10BASE-T1S PHYs.
Reviewed-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
commit 4bb7aac70b ("net: phy: fix circular LEDS_CLASS dependencies")
solved a build failure, but introduces a new config knob with a default
'y' value: PHYLIB_LEDS.
The latter is against the current new config policy. The exception
was raised to allow the user to catch bad configurations without led
support.
Anyway the current definition of PHYLIB_LEDS does not fit the above
goal: if LEDS_CLASS is disabled, the new config will be available
only with PHYLIB disabled, too.
Hide the mentioned config, to preserve the randconfig testing done so
far, while respecting the mentioned policy.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/d82489be8ed911c383c3447e9abf469995ccf39a.1682496488.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds support for the Microchip LAN867x 10BASE-T1S family
(LAN8670/1/2). The driver supports P2MP with PLCA.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CBTX PHY is a Fast Ethernet PHY integrated into the SJA1110 A/B/C
automotive Ethernet switches.
It was hoped it would work with the Generic PHY driver, but alas, it
doesn't. The most important reason why is that the PHY is powered down
by default, and it needs a vendor register to power it on.
It has a linear memory map that is accessed over SPI by the SJA1110
switch driver, which exposes a fake MDIO controller. It has the
following (and only the following) standard clause 22 registers:
0x0: MII_BMCR
0x1: MII_BMSR
0x2: MII_PHYSID1
0x3: MII_PHYSID2
0x4: MII_ADVERTISE
0x5: MII_LPA
0x6: MII_EXPANSION
0x7: the missing MII_NPAGE for Next Page Transmit Register
Every other register is vendor-defined.
The register map expands the standard clause 22 5-bit address space of
0x20 registers, however the driver does not need to access the extra
registers for now (and hopefully never). If it ever needs to do that, it
is possible to implement a fake (software) page switching mechanism
between the PHY driver and the SJA1110 MDIO controller driver.
Also, Auto-MDIX is turned off by default in hardware, the driver turns
it on by default and reports the current status. I've tested this with a
VSC8514 link partner and a crossover cable, by forcing the mode on the
link partner, and seeing that the CBTX PHY always sees the reverse of
the mode forced on the VSC8514 (and that traffic works). The link
doesn't come up (as expected) if MDI modes are forced on both ends in
the same way (with the cross-over cable, that is).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230418190141.1040562-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CONFIG_PHYLIB symbol is selected by a number of device drivers that
need PHY support, but it now has a dependency on CONFIG_LEDS_CLASS,
which may not be enabled, causing build failures.
Avoid the risk of missing and circular dependencies by guarding the
phylib LED support itself in another Kconfig symbol that can only be
enabled if the dependency is met.
This could be made a hidden symbol and always enabled when both CONFIG_OF
and CONFIG_LEDS_CLASS are reachable from the phylib, but there may be an
advantage in having users see this option when they have a misconfigured
kernel without built-in LED support.
Fixes: 01e5b728e9 ("net: phy: Add a binding for PHY LEDs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230420084624.3005701-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Amlogic Meson internal PHY's have the same register layout as
certain SMSC PHY's (also for non-c22-standard registers). This seems
to be more than just coincidence. Apparently they also need the same
workaround for EDPD mode (energy detect power down). Therefore let's
reuse SMSC PHY driver functionality in the meson-gxl PHY driver.
Tested with a G12A internal PHY. I don't have GXL test hw,
therefore I replace only the callbacks that are identical in
the SMSC PHY driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on AM335x platform with yt8531 board. On the
board, yt8531 gigabit ethernet phy works in utp mode, RGMII
interface, supports 1000M/100M/10M speeds, and wol(magic package).
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the onsemi NCN26000 10BASE-T1S industrial
Ethernet PHY. The driver supports Point-to-Multipoint operation without
auto-negotiation and with link control handling. The PHY also features
PLCA for improving performance in P2MP mode.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete a few lines of "depends on PHYLIB" since they are inside
an "if PHYLIB / endif # PHYLIB" block, i.e., they are redundant
and the other 50+ drivers there don't use "depends on PHYLIB"
since it is not needed.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221207044257.30036-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We added patch for motorcomm.c to support YT8531S. This patch has
been tested on AM335x platform which has one YT8531S interface
card and passed all test cases.
The tested cases indluding: YT8531S UTP function with support of
10M/100M/1000M; YT8531S Fiber function with support of 100M/1000M;
and YT8531S Combo function that supports auto detection of media type.
Since most functions of YT8531S are similar to YT8521 and we reuse some
codes for YT8521 in the patch file.
Signed-off-by: Frank <Frank.Sae@motor-comm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for the motorcomm yt8521 gigabit ethernet phy. We have verified
the driver on StarFive VisionFive development board, which is developed by
Shanghai StarFive Technology Co., Ltd.. On the board, yt8521 gigabit ethernet
phy works in utp mode, RGMII interface, supports 1000M/100M/10M speeds, and
wol(magic package).
Signed-off-by: Frank <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPY115 and GPY2xx PHYs contain an integrated temperature sensor. It
accuracy is +/- 5°C. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220622141716.3517645-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds PTP support for BCM54210E Broadcom PHYs, in particular,
the BCM54213PE, as used in the Rasperry PI CM4. It has only been
tested on that hardware.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DP83TD510E is an ultra-low power Ethernet physical layer transceiver
that supports 10M single pair cable.
This driver was tested with NXP SJA1105, STMMAC and ASIX AX88772B USB Ethernet
controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building driver CONFIG_MICREL_PHY the follow error shows up:
aarch64-linux-gnu-ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info':
micrel.c:(.text+0x1764): undefined reference to `ptp_clock_index'
micrel.c:(.text+0x1764): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ptp_clock_index'
aarch64-linux-gnu-ld: drivers/net/phy/micrel.o: in function `lan8814_probe':
micrel.c:(.text+0x4720): undefined reference to `ptp_clock_register'
micrel.c:(.text+0x4720): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ptp_clock_register'
Rework Kconfig for MICREL_PHY to depend on 'PTP_1588_CLOCK_OPTIONAL'.
Arnd describes in a good way why its needed to add this depends in patch
e5f3155267 ("ethernet: fix PTP_1588_CLOCK dependencies").
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220314110254.12498-1-anders.roxell@linaro.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
