Since the beginning gsi_trans_commit_wait_timeout() has existed to
provide a way to allow waiting a limited time for a transaction
to complete. But that function has never been used.
In fact, there is no use for this function, because a transaction
committed to hardware should *always* complete. The only reason it
might not complete is if there were a hardware failure, or perhaps a
system configuration error.
Furthermore, if a timeout ever did occur, the IPA hardware would be
in an indeterminate state, from which there is no recovery. It
would require some sort of complete IPA reset, and would require the
participation of the modem, and at this time there is no such
sequence defined.
So get rid of the definition of gsi_trans_commit_wait_timeout(), and
update a few comments accordingly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't assume that a 500 microsecond time limit should be used for
all receive endpoints that support aggregation. Instead, specify
the time limit to use in the configuration data.
Set a 500 microsecond limit for all existing RX endpoints, as before.
Checking for overflow for the time limit field is a bit complicated.
Rather than duplicate a lot of code in ipa_endpoint_data_valid_one(),
call WARN() if any value is found to be too large when encoding it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flag for AP receive endpoints that indicates whether
a "hard limit" is used as a criterion for closing aggregation.
Add comments explaining the difference between "hard" and "soft"
aggregation limits.
Pass a flag to ipa_aggr_size_kb() so it computes the proper
aggregation size value whether using hard or soft limits. Move
that function earlier in "ipa_endpoint.c" so it can be used
without a forward-reference.
Update ipa_endpoint_data_valid_one() so it validates endpoints whose
data indicate a hard aggregation limit is used, and so it reports
set aggregation flags for endpoints without aggregation enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new Boolean flag for RX endpoints defining whether HOLB drop
is initially enabled or disabled for the endpoint. All existing AP
endpoints should have HOLB drop disabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All elements of the default endpoint configuration are used in the
code when programming an endpoint for use. But none of the other
configuration data is ever needed once things are initialized.
So rather than saving a pointer to *all* of the configuration data,
save a copy of only the endpoint configuration portion.
This will eventually allow endpoint configuration to be modifiable
at runtime. But even before that it means we won't keep a pointer
to configuration data after when no longer needed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the just-moved data structure types to drop the "_data"
suffix, to make it more obvious they are no longer meant to be used
just as read-only initialization data. Rename the fields and
variables of these types to use "config" instead of "data" in the
name. This is another small step meant to facilitate review.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we program an RX endpoint to have no header (header length is 0),
header-related endpoint configuration values are meaningless and are
ignored.
The only case we support that defines a header is QMAP endpoints.
In ipa_endpoint_init_hdr_ext() we set the endianness mask value
unconditionally, but it should not be done if there is no header
(meaning it is not configured for QMAP).
Set the endianness conditionally, and rearrange the logic in that
function slightly to avoid testing the qmap flag twice.
Delete an incorrect comment in ipa_endpoint_init_aggr().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an RX endpoint receives packets containing status headers, and a
packet in the buffer is not dropped, ipa_endpoint_skb_copy() is
responsible for wrapping the packet data in an SKB and forwarding it
to ipa_modem_skb_rx() for further processing.
If ipa_endpoint_skb_copy() gets a null pointer from build_skb(), it
just returns early. But in the process it doesn't record that as a
dropped packet in the network device statistics.
Instead, call ipa_modem_skb_rx() whether or not the SKB pointer is
NULL; that function ensures the statistics are properly updated.
Fixes: 1b65bbcc9a ("net: ipa: skip SKB copy if no netdev")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aggregation byte limit for an endpoint is currently computed
based on the endpoint's receive buffer size.
However, some bytes at the front of each receive buffer are reserved
on the assumption that--as with SKBs--it might be useful to insert
data (such as headers) before what lands in the buffer.
The aggregation byte limit currently doesn't take into account that
reserved space, and as a result, aggregation could require space
past that which is available in the buffer.
Fix this by reducing the size used to compute the aggregation byte
limit by the NET_SKB_PAD offset reserved for each receive buffer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than tracking the number of receive buffer transactions that
have been submitted without a doorbell, just track the total number
of transactions that have been issued. Then ring the doorbell when
that number modulo the replenish batch size is 0.
The effect is roughly the same, but the new count is slightly more
interesting, and this approach will someday allow the replenish
batch size to be tuned at runtime.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replenishing is now solely driven by whether transactions are
available for a channel, and it doesn't really matter whether
we replenish before or after we deliver received packets to the
network stack.
Replenishing before delivering the payload adds a little latency.
Eliminate that by requesting a replenish after the payload is
delivered.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer use the replenish_backlog atomic variable to decide
when we've got work to do providing receive buffers to hardware.
Basically, we try to keep the hardware as full as possible, all the
time. We keep supplying buffers until the hardware has no more
space for them.
As a result, we can get rid of the replenish_backlog field and the
atomic operations performed on it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new function that returns true if all transactions for a
channel are available for use.
Use it in ipa_endpoint_replenish_enable() to see whether to start
replenishing, and in ipa_endpoint_replenish() to determine whether
it's necessary after a failure to schedule delayed work to ensure a
future replenish attempt occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than determining when to stop replenishing using the
replenish backlog, just stop when we have exhausted all available
transactions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replenishing, have ipa_endpoint_replenish() allocate a
transaction, and pass that to ipa_endpoint_replenish_one() to fill.
Then, if that produces no error, commit the transaction within the
replenish loop as well. In this way we can distinguish between
transaction failures and buffer allocation/mapping failures.
Failure to allocate a transaction simply means the hardware already
has as many receive buffers as it can hold. In that case we can
break out of the replenish loop because there's nothing more to do.
If we fail to allocate or map pages for the receive buffer, just
try again later.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decide whether the doorbell should be signaled when committing a
replenish transaction in the main replenish loop, rather than in
ipa_endpoint_replenish_one(). This is a step to facilitate the
next patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three spots call ipa_endpoint_replenish(), and just one of those
requests that the backlog be incremented after completing the
replenish operation.
Instead, have the caller increment the backlog, and get rid of the
add_one argument to ipa_endpoint_replenish().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A transaction failure only occurs if no more transactions are
available for an endpoint. It's a very cheap test.
When replenishing an RX endpoint buffer, there's no point in
allocating pages if transactions are exhausted. So don't bother
doing so unless the transaction allocation succeeds.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The replenish_saved field keeps track of the number of times a new
buffer is added to the backlog when replenishing is disabled. We
don't really use it though, so there's no need for us to track it
separately. Whether replenishing is enabled or not, we can simply
increment the backlog.
Get rid of replenish_saved, and initialize and increment the backlog
where it would have otherwise been used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow RX endpoints to have differing receive buffer sizes. Define
the receive buffer size in the configuration data, and use that
rather than IPA_RX_BUFFER_SIZE when configuring the endpoint.
Add verification in ipa_endpoint_data_valid_one() that the receive
buffer specified for AP RX endpoints is both big enough to handle at
least one full packet, and not so big in an aggregating endpoint
that its size can't be represented when programming the hardware.
Move aggr_byte_limit_max() up in "ipa_endpoint.c" so it can be used
earlier in the file without a forward-reference.
Initially we'll just keep the 8KB receive buffer size already in use
for all AP RX endpoints..
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have seen cases where an endpoint RX completion interrupt arrives
while replenishing for the endpoint is underway. This causes another
instance of replenishing to begin as part of completing the receive
transaction. If this occurs it can lead to transaction corruption.
Use a new flag to ensure only one replenish instance for an endpoint
executes at a time.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new replenish_flags bitmap to contain Boolean flags
associated with an endpoint's replenishing state. Replace the
replenish_enabled field with a flag in that bitmap. This is to
prepare for the next patch, which adds another flag.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_replenish(), if an error occurs when attempting to
replenish a receive buffer, we just quit and try again later. In
that case we increment the backlog count to reflect that the attempt
was unsuccessful. Then, if the add_one flag was true we increment
the backlog again.
This second increment is not included in the backlog local variable
though, and its value determines whether delayed work should be
scheduled. This is a bug.
Fix this by determining whether 1 or 2 should be added to the
backlog before adding it in a atomic_add_return() call.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One quirk for certain versions of IPA is that endpoint DELAY mode
does not work properly. IPA DELAY mode prevents any packets from
being delivered to the IPA core for processing on a TX endpoint.
The AP uses DELAY mode when the modem crashes, to prevent modem TX
endpoints from generating traffic during crash recovery. Without
this, there is a chance the hardware will stall during recovery from
a modem crash.
To achieve a similar effect, a GSI FLOW_CONTROLLED channel state
was created. A STARTED TX channel can be placed in FLOW_CONTROLLED
state, which prevents the transfer of any more packets. A channel
in FLOW_CONTROLLED state can be either returned to STARTED state, or
can be transitioned to STOPPED state.
Because this operates on GSI channels, two generic commands were
added to allow the AP to control this state for modem channels
(similar to the ALLOCATE and HALT channel commands).
Previously the code assumed this quirk only applied to IPA v4.2.
In fact, channel flow control (rather than endpoint DELAY mode)
should be used for all versions *starting* with IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_endpoint_skb_copy(), a new socket buffer structure is
allocated so that some data can be copied into it. However, after
doing this, if the endpoint has a null netdev pointer, we just drop
free the socket buffer.
Instead, check endpoint->netdev pointer first, and just return early
if it's null. Also return early if the SKB allocation fails, to
avoid the deeper indentation in the normal path.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During setup, ipa_endpoint_program() programs each endpoint with
various configuration parameters. One of those registers defines
whether to drop packets when a head-of-line blocking condition is
detected on an RX endpoint. We currently assume this is disabled;
instead, explicitly set it to be disabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The head-of-line block (HOLB) drop timer is only meaningful when
dropping packets due to blocking is enabled. Given that, redefine
the interface so the timer is specified when enabling HOLB drop, and
use a different function when disabling.
To enable and disable HOLB drop, these functions will now be used:
ipa_endpoint_init_hol_block_enable(endpoint, milliseconds)
ipa_endpoint_init_hol_block_disable(endpoint)
The existing ipa_endpoint_init_hol_block_enable() becomes a helper
function, renamed ipa_endpoint_init_hol_block_en(), and used with
ipa_endpoint_init_hol_block_timer() to enable HOLB block on an
endpoint.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling ipa_cmd_pipeline_clear() after stopping the channel
underlying the AP<-modem RX endpoint can lead to a deadlock.
This occurs in the ->runtime_suspend device power operation for the
IPA driver. While this callback is in progress, any other requests
for power will block until the callback returns.
Stopping the AP<-modem RX channel does not prevent the modem from
sending another packet to this endpoint. If a packet arrives for an
RX channel when the channel is stopped, an SUSPEND IPA interrupt
condition will be pending. Handling an IPA interrupt requires
power, so ipa_isr_thread() calls pm_runtime_get_sync() first thing.
The problem occurs because a "pipeline clear" command will not
complete while such a SUSPEND interrupt condition exists. So the
SUSPEND IPA interrupt handler won't proceed until it gets power;
that won't happen until the ->runtime_suspend callback (and its
"pipeline clear" command) completes; and that can't happen while
the SUSPEND interrupt condition exists.
It turns out that in this case there is no need to use the "pipeline
clear" command. There are scenarios in which clearing the pipeline
is required while suspending, but those are not (yet) supported
upstream. So a simple fix, avoiding the potential deadlock, is to
stop calling ipa_cmd_pipeline_clear() in ipa_endpoint_suspend().
This removes the only user of ipa_cmd_pipeline_clear(), so get rid
of that function. It can be restored again whenever it's needed.
This is basically a manual revert along with an explanation for
commit 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()").
Fixes: 6cb63ea6a3 ("net: ipa: introduce ipa_cmd_tag_process()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The head-of-line blocking timer should only be modified when
head-of-line drop is disabled.
One of the steps in recovering from a modem crash is to enable
dropping of packets with timeout of 0 (immediate). We don't know
how the modem configured its endpoints, so before we program the
timer, we need to ensure HOL_BLOCK is disabled.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.5, the HOL_BLOCK_EN register must be written
twice when enabling head-of-line blocking avoidance.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, rename "ipa_clock.c" to be "ipa_power.c" and "ipa_clock.h"
to be "ipa_power.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename a number of functions to clarify that there is no longer a
notion of an "IPA clock," but rather that the functions are more
generally related to IPA power management.
ipa_clock_enable() -> ipa_power_enable()
ipa_clock_disable() -> ipa_power_disable()
ipa_clock_rate() -> ipa_core_clock_rate()
ipa_clock_init() -> ipa_power_init()
ipa_clock_exit() -> ipa_power_exit()
Rename the ipa_clock structure to be ipa_power. Rename all
variables and fields using that structure type "power" rather
than "clock".
Rename the ipa_clock_data structure to be ipa_power_data, and more
broadly, just substitute "power" for "clock" in places that
previously represented things related to the "IPA clock".
Update comments throughout.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GSI layer has the IPA version now, so there's no need for
version-specific flags to be passed from IPA. One instance of
this is in gsi_channel_suspend() and gsi_channel_resume(), which
indicate whether or not the endpoint suspend is implemented by
GSI stopping the channel. We can make that determination based
on gsi->version, eliminating the need for a Boolean flag in those
functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've added commented assertions to record certain properties that
can be assumed to hold in certain places in the IPA code. Convert
these into real WARN_ON() calls so the assertions are actually
checked, using the standard WARN_ON() mechanism.
Where errors can be returned, return an error if a warning is
triggered.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLAVOR_0 version first appears in IPA v3.5, so avoid attempting
to read it for versions prior to that.
This register contains a concise definition of the number and
direction of endpoints supported by the hardware, and without it
we can't verify endpoint configuration in ipa_endpoint_config().
In this case, just indicate that any endpoint number is available
for use.
Originally proposed by AngeloGioacchino Del Regno.
Link: https://lore.kernel.org/netdev/20210211175015.200772-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: AngeloGioacchino Del Regno
Signed-off-by: David S. Miller <davem@davemloft.net>
The cost of validating the endpoint configuration data is not all
that high, so just do it unconditionally, rather than doing so only
when IPA_VALIDATAION is defined.
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c88c34fcf8.
The RMNet driver now supports inline checksum offload.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.5, IP payload checksum offload is implemented
differently.
Prior to v4.5, the IPA hardware appends an rmnet_map_dl_csum_trailer
structure to each packet if checksum offload is enabled in the
download direction (modem->AP). In the upload direction (AP->modem)
a rmnet_map_ul_csum_header structure is prepended before each sent
packet.
Starting with IPA v4.5, checksum offload is implemented using a
single new rmnet_map_v5_csum_header structure which sits between
the QMAP header and the packet data. The same header structure
is used in both directions.
The new header contains a header type (CSUM_OFFLOAD); a checksum
flag; and a flag indicating whether any other headers follow this
one. The checksum flag indicates whether the hardware should
compute (and insert) the checksum on a sent packet. On a received
packet the checksum flag indicates whether the hardware confirms the
checksum value in the payload is correct.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checksum offload for IPA v4.5+ is implemented differently, using
"inline" offload (which uses a common header format for both upload
and download offload).
The IPA hardware must be programmed to enable MAP checksum offload,
but the RMNet driver is responsible for interpreting checksum
metadata supplied with messages.
Currently, the RMNet driver does not support inline checksum offload.
This support is imminent, but until it is available, do not allow
newer versions of IPA to specify checksum offload for endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago changes were made to stop referring to clearing the
hardware pipeline as a "tag process." Fix a comment to use the
newer terminology.
Get rid of a pointless double-negation of the Boolean toward_ipa
flag in ipa_endpoint_config().
make ipa_endpoint_exit_one() private; it's only referenced inside
"ipa_endpoint.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove repeated words "that" and "the".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the ENDP_INIT_NAT register for setting up the NAT
configuration for an endpoint. We aren't using NAT at this
time, so explicitly set the type to BYPASS for all endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify conditional tests throughout the IPA code so they do not
assume that IPA v3.5.1 is the oldest version supported. Also remove
assumptions that IPA v4.5 is the newest version of IPA supported.
Augment versions in comments with "+", to be clearer that the
comment applies to a version and subsequent versions. (E.g.,
"present for IPA v4.2+" instead of just "present for v4.2".)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only program the sequencer type for TX endpoints. So move the
definition of the sequencer type fields into the TX-specific portion
of the endpoint configuration data. There's no need to maintain
this in the IPA structure; we can extract it from the configuration
data it points to in the one spot it's needed.
We previously specified the sequencer type for RX endpoints with
INVALID values. These are no longer needed, so get rid of them.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IPA endpoint has a sequencer that must be configured based on how
the endpoint is to be used. Currently the IPA code programs the
sequencer type by splitting a value into four 4-bit nibbles. Doing
that doesn't really add much value, and regardless, a better way of
splitting the sequencer type is into two halves--the lower byte
describing how normal packet processing is handled, and the next
byte describing information about processing replicas.
So split the sequencer type into two sub-parts: the sequencer type
and the replication sequencer type. Define the values supported for
the "main" sequencer type, and define the values supported for the
replication part separately.
In addition, the sequencer type names are quite verbose, encoding
what the type includes, but also what it *excludes*. Rename the
sequencer types in a way that mainly describes the number of passes
that a packet takes through the IPA processing pipeline, and how
many of those passes end by supplying the processed packet to the
microprocessor.
The result expands the supported types beyond what is required for
now, but simplifies the way these are defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a build-time check that the packet status structure is a
multiple of 4 bytes in size. It's not clear where that constraint
comes from, but the structure defines what hardware provides so its
definition won't change. Get rid of the check; it adds no value.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The count argument to ipa_endpoint_replenish() is only ever 0 or 1,
and always will be (because we always handle each receive buffer in
a single transaction). Rename the argument to be add_one and change
it to be Boolean.
Update the function description to reflect the current code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When extracting the destination endpoint ID from the status in
ipa_endpoint_status_skip(), u32_get_bits() is used. This happens to
work, but it's wrong: the structure field is only 8 bits wide
instead of 32.
Fix this by using u8_get_bits() to get the destination endpoint ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sparse warns that the assignment of the metadata mask for a QMAP
endpoint in ipa_endpoint_init_hdr_metadata_mask() is a bad
assignment. We know we want the mask value to be big endian, even
though the value we write is in host byte order. Use a __force
tag to indicate we really mean it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are times, such as when the modem crashes, when we issue
commands to clear the IPA hardware pipeline. These commands include
a data transfer command that delivers a small packet directly to the
default (AP<-LAN RX) endpoint.
The places that do this wait for the transactions that contain these
commands to complete, but the pipeline can't be assumed clear until
the sent packet has been *received*.
The small transfer will be delivered with a status structure, and
that status will indicate its tag is valid. This is the only place
we send a tagged packet, so we use the tag to determine when the
pipeline clear packet has arrived.
Add a completion to the IPA structure to to be used to signal
the receipt of a pipeline clear packet. Create a new function
ipa_cmd_pipeline_clear_wait() that will wait for that completion.
Reinitialize the completion whenever pipeline clear commands are
added to a transaction. Extend ipa_endpoint_status_tag() to check
whether a packet whose status contains a valid tag was sent from the
AP->command TX endpoint, and if so, signal the new IPA completion.
Have all callers of ipa_cmd_pipeline_clear_add() wait for the
pipeline clear indication after the transaction that clears the
pipeline has completed.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce ipa_endpoint_status_tag(), which returns true if received
status indicates its tag field is valid. The endpoint parameter is
not yet used.
Call this from ipa_status_drop_packet(), and drop the packet if the
status indicates the tag was valid. Pass the endpoint pointer to
ipa_status_drop_packet(), and rename it ipa_endpoint_status_drop().
The endpoint will be used in the next patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rearrange some comments and assignments made when handling a packet
that is received with status, aiming to improve understandability.
Use DIV_ROUND_CLOSEST() to get a better per-packet true size estimate.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a set of functions and symbols related to performing
"tag_process" immediate commands to clear the IPA pipeline. The
name is related to one of the commands issued when doing this, but
it doesn't really convey the overall purpose of taking this action.
The purpose is to take some steps to "clear out" the hardware
pipeline, and to wait until that process completes, to ensure the
IPA hardware is in a well-defined state.
Rename these symbols to use "pipeline_clear" in their names instead.
Add some comments to explain a bit more about what's going on.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
65;6003;1c
The use of msleep() for small periods (less than 20 milliseconds) is
not recommended because the actual delay can be much different than
expected.
We use msleep(1) in several places in the IPA driver to insert short
delays. Replace them with usleep_range calls, which should reliably
delay a period in the range requested.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend ipa_reg_init_hol_block_timer_val() so it properly calculates
the head-of-line block timeout to use for IPA v4.5.
Introduce hol_block_timer_qtime_val() to compute the value to use
for IPA v4.5, where Qtime is used as the basis of the timer. Call
that function from hol_block_timer_val() for IPA v4.5.
Both of these are private functions, so shorten their names a bit so
they don't take up so much space on the line.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change aggr_time_limit_encoded() to properly calculate the
aggregation time limit to use for IPA v4.5.
Older IPA versions program the AGGR_GRANULARITY field of the
of the COUNTER_CFG register to set the granularity of the
aggregation timer, which we configure to be 500 microseconds.
Instead, IPA v4.5 selects between two possible granularity values
derived from the 19.2 MHz Qtime clock. These granularities are
100 microseconds or 1 millisecond per tick. We use the smaller
granularity if possible, unless the desired period is too large
to be specified that way.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA v4.5 significantly changes the format of the configuration
register used for endpoint aggregation. The AGGR_BYTE_LIMIT field
is now larger, and the positions of other fields are shifted. This
complicates the way we have to access this register because functions
like u32_encode_bits() require their field mask argument to be constant.
A further complication is that we want to know the maximum value
representable by at least one of these fields, and that too requires
a constant field mask.
This patch adds support for IPA v4.5 endpoint aggregation registers
in a way that continues to support "legacy" IPA hardware. It does
so in a way that keeps field masks constant.
First, for each variable field mask, we define an inline function
whose return value is either the legacy value or the IPA v4.5 value.
Second, we define functions for these fields that encode a value
to use in each field based on the IPA version (this approach is
already used elsewhere). The field mask provided is supplied by
the function mentioned above.
Finally, for the aggregation byte limit fields where we want to
know the maximum representable value, we define a function that
returns that maximum, computed from the appropriate field mask.
We can no longer verify at build time that our buffer size is
in the range that can be represented by the aggregation byte
limit field. So remove the test done by a BUILD_BUG_ON() call
in ipa_endpoint_validate_build(), and implement a comparable check
at the top of ipa_endpoint_data_valid().
Doing that makes ipa_endpoint_validate_build() contain a single
line BUILD_BUG_ON() call, so just remove that function and move
the remaining line into ipa_endpoint_data_valid().
One final note: the aggregation time limit value for IPA v4.5 needs
to be computed differently. That is handled in an upcoming patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the IPA code to make use of the updated IPA v4.5 register
definitions. Generally what this patch does is, if IPA v4.5
hardware is in use:
- Ensure new registers or fields in IPA v4.5 are updated where
required
- Ensure registers or fields not supported in IPA v4.5 are not
examined when read, or are set to 0 when written
It does this while preserving the existing functionality for IPA
versions lower than v4.5.
The values to program for QSB_MAX_READS and QSB_MAX_WRITES and the
source and destination resource counts are updated to be correct for
all versions through v4.5 as well.
Note that IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
already reflect that 5 is an acceptable number of resources (which
IPA v4.5 implements).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA v4.5 adds a few fields to the endpoint header and extended
header configuration registers that represent new high-order bits
for certain offsets and sizes. Add code to incorporate these upper
bits into the registers for IPA v4.5.
This includes creating ipa_header_size_encoded(), which handles
encoding the metadata offset field for use in the ENDP_INIT_HDR
register in a way appropriate for the hardware version. This and
ipa_metadata_offset_encoded() ensure the mask argument passed to
u32_encode_bits() is constant.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some last cleanups for the existing IPA register definitions:
- Remove the definition of IPA_REG_ENABLED_PIPES_OFFSET, because
it is not used.
- Use "IPA_" instead of "BAM_" as the prefix on fields associated
with the FLAVOR_0 register. We use GSI (not BAM), but the
fields apply to both GSI and BAM.
- Get rid of the definition of IPA_CS_RSVD; it is never used.
- Add two missing field mask definitions for the INIT_DEAGGR
endpoint register.
- Eliminate a few of the defined sequencer types, because they
are unused. We can add them back when needed.
- Add a field mask to indicate which bit causes an interrupt on
the microcontroller.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA version 3.5.1 represents the timer used in avoiding head-of-line
blocking with a simple tick count. IPA v4.2 changes that, instead
splitting the timer field into two parts (base and scale) to
represent the ticks in the timer period.
IPA v4.0 and IPA v4.1 use the same method as IPA v3.5.1. Change the
test in ipa_reg_init_hol_block_timer_val() so the result is correct
for those versions as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the IPA version in gsi_channel_program() to determine whether
we should enable the GSI doorbell engine when requested. This way,
callers only say whether or not it should be enabled if needed,
regardless of hardware version.
Rename the "legacy" argument to gsi_channel_reset(), and have
it indicate whether the doorbell engine should be enabled when
reprogramming following the reset.
Change all callers of gsi_channel_reset() to indicate whether to
enable the doorbell engine after reset, independent of hardware
version.
Rework a little logic in ipa_endpoint_reset() to get rid of the
"legacy" variable previously passed to gsi_channel_reset().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With IPA v3.5.1, if IPA aggregation is active at the time an
underlying GSI channel reset is performed, some special handling
is required.
There is logic in ipa_endpoint_reset() that arranges for that
special handling, but it's done for all hardware versions, not
just IPA v3.5.1.
Fix the logic to properly restrict the special behavior.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201102173435.5987-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPA hardware manages various resources (e.g. descriptors)
internally to perform its functions. The resources are grouped,
allowing different endpoints to use separate resource pools. This
way one group of endpoints can be configured to operate unaffected
by the resource use of endpoints in a different group.
Endpoints should be assigned to a resource group, but we currently
don't do that.
Define a new resource_group field in the endpoint configuration
data, and use it to assign the proper resource group to use for
each AP endpoint.
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When processing a system suspend request we suspend modem endpoints
if they are enabled, and call ipa_cmd_tag_process() (which issues
IPA commands) to ensure the IPA pipeline is cleared. It is an error
to attempt to issue an IPA command before setup is complete, so this
is clearly a bug. But we also shouldn't suspend or resume any
endpoints that have not been set up.
Have ipa_endpoint_suspend() and ipa_endpoint_resume() immediately
return if setup hasn't completed, to avoid any attempt to configure
endpoints or issue IPA commands in that case.
Fixes: 84f9bd12d4 ("soc: qcom: ipa: IPA endpoints")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the field masks used for fields in a status structure are
unused. Remove their definitions; we can add them back again when
we actually use them to handle arriving status messages. These are
warned about if "W=2" is added to the build command.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the deaggregation status exception type is ever actually used.
If any other status exception type is reported we basically ignore
it, and consume the packet. Remove the unused definitions of status
exception type symbols; they can be added back when we actually
handle them.
Separately, two consecutive if statements test the same condition
near the top of ipa_endpoint_suspend_one(). Instead, use a single
test with a block that combines the previously-separate lines of
code.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three status opcodes are not currently supported. Symbols
representing their numeric values are defined but never used.
Remove those unused definitions; they can be defined again
when they actually get used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit affects comments (and in one case, whitespace) only.
Throughout the IPA code, return statements are documented using
"@Return:", whereas they should use "Return:" instead. Fix these
mistakes.
In function definitions, some parameters are missing their comment
to describe them. And in structure definitions, some fields are
missing their comment to describe them. Add these missing
descriptions.
Some arguments changed name and type along the way, but their
descriptions were not updated (an endpoint pointer is now used in
many places that previously used an endpoint ID). Fix these
incorrect parameter descriptions.
In the description for the ipa_clock structure, one field had a
semicolon instead of a colon in its description. Fix this.
Add a missing function description for ipa_gsi_endpoint_data_empty().
All of these issues were identified when building with "W=1".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IPA v4.2, the exact interpretation of the register that defines
the timeout for avoiding head-of-line blocking was a little unclear.
We're only assigning a 0 timeout to it right now, so that wasn't
very important. But now that I know how it's supposed to work, I'm
fixing it.
The register represents a tick counter, where each tick is equal to
128 IPA core clock cycles. For IPA v3.5.1, the register contains
a simple counter value. But for IPA v4.2, the register contains two
fields, base and scale, which approximate the tick counter as:
ticks = base << scale
The base and scale values to use for a given tick count are computed
using clever bit operations, and measures are taken to make the
resulting time period as close as possible to that requested.
There's no need for ipa_endpoint_init_hol_block_timer() to return
an error, so change its return type to void.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have functions that write endpoint configuration registers return
immediately if they are not valid for the direction of transfer for
the endpoint. This allows most of the calls in ipa_endpoint_program()
to be made unconditionally. Reorder the register writes to match
the order of their definition (based on offset).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 4.0+ does not support endpoint suspend. Put a test at
the top of ipa_endpoint_program_suspend() that returns immediately
if suspend is not supported rather than making that check in the caller.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 3.5.1 has a hardware quirk that requires special
handling if an RX endpoint is suspended while aggregation is active.
This handling is implemented by ipa_endpoint_suspend_aggr().
Have ipa_endpoint_program_suspend() be responsible for calling
ipa_endpoint_suspend_aggr() if suspend mode is being enabled on
an endpoint. If the endpoint does not support aggregation, or if
aggregation isn't active, this call will continue to have no effect.
Move the definition of ipa_endpoint_suspend_aggr() up in the file so
its definition precedes the new earlier reference to it. This
requires ipa_endpoint_aggr_active() and ipa_endpoint_force_close()
to be moved as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 4.2 has a hardware quirk that affects endpoint delay
mode, so it isn't used there. Isolate the test that avoids using
delay mode for that version inside ipa_endpoint_program_delay(),
rather than making that check in the caller.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The convention throughout the IPA driver is to directly use
single-bit field mask values, rather than using (for example)
u32_encode_bits() to set or clear them.
Fix the one place that doesn't follow that convention, which sets
HOL_BLOCK_EN_FMASK in ipa_endpoint_init_hol_block_enable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_MODE endpoint configuration register is only valid for TX
endpoints. Rather than writing a zero to that register for RX
endpoints, avoid writing the register at all.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_HDR_METADATA_MASK endpoint configuration register is only
valid for RX endpoints. Rather than writing a zero to that register
for TX endpoints, avoid writing the register at all.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_HOL_BLOCK_EN and INIT_HOL_BLOCK_TIMER endpoint registers
are only valid for RX endpoints.
Have ipa_endpoint_modem_hol_block_clear_all() skip writing these
registers for TX endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the "limit" local variable in ipa_endpoint_init_aggr() when
setting the aggregation size limit. Simple cleanup.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Halve the time limit used when aggregation is enabled on an RX
endpoint, to half a millisecond.
Use DIV_ROUND_CLOSEST() to compute the value that represents the
time period, to get better accuracy in the event the time limit is
not an even multiple of the granularity.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new function ipa_cmd_tag_process() that simply allocates a
transaction, adds a tag process command to it to clear the hardware
pipeline, and commits the transaction.
Call it in from ipa_endpoint_suspend(), after suspending the modem
endpoints but before suspending the AP command TX and AP LAN RX
endpoints (which are used by the tag sequence).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only QMAP endpoints should be configured to find a pad size field
within packet headers. They are found in the first byte of the QMAP
header (and the hardware fills only the 6 bits in that byte that
constitute the pad_len field).
The RMNet driver assumes the pad_len field is valid for received
packets, so we want to ensure the pad_len field is filled in that
case. That driver also assumes the length in the QMAP header
includes the pad bytes.
The RMNet driver does *not* pad the packets it sends, so the pad_len
field can be ignored.
Fix ipa_endpoint_init_hdr_ext() so it only marks the pad field
offset valid for QMAP RX endpoints, and in that case indicates
that the length field in the header includes the pad bytes.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upper two nibbles of the sequencer type were not used for
SDM845, and were assumed to be 0. But for SC7180 they are used, and
so they must be programmed by ipa_endpoint_init_seq(). Fix this bug.
IPA_SEQ_PKT_PROCESS_NO_DEC_NO_UCP_DMAP doesn't have a descriptive
comment, so add one.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way the mask value is programmed for QMAP RX endpoints was based
on some wrong assumptions about the way metadata containing the QMAP
mux_id value is formatted. The metadata value supplied by the
modem is *not* in QMAP format, and in fact contains the mux_id we
want in its (big endian) low-order byte. That byte must be written
by the IPA into offset 1 of the QMAP header it inserts before the
received packet.
QMAP TX endpoints *do* use a QMAP header as the metadata sent with
each packet. The modem assumes this, and based on that assumes the
mux_id is in the second byte. To match those assumptions we must
program the modem TX (QMAP) endpoint HDR register to indicate the
metadata will be found at offset 0 in the message header.
The previous configuration managed to work, but it was not working
correctly. This patch fixes a bug whose symptom was receipt of
messages containing the wrong QMAP mux_id.
In fixing this, get rid of ipa_rmnet_mux_id_metadata_mask(), which
was more or less defined so there was a separate place to explain
what was happening as we generated the mask value. Instead, put a
longer description of how this works above ipa_endpoint_init_hdr(),
and define the metadata mask to use as a simple constant.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "transactio" -> "transaction". Also an alignment correction.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building arm64 allyesconfig:
drivers/net/ipa/ipa_endpoint.c: In function 'ipa_endpoint_stop_rx_dma':
drivers/net/ipa/ipa_endpoint.c:1274:13: error: 'IPA_ENDPOINT_STOP_RX_SIZE' undeclared (first use in this function)
drivers/net/ipa/ipa_endpoint.c:1274:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ipa/ipa_endpoint.c:1289:2: error: implicit declaration of function 'ipa_cmd_dma_task_32b_addr_add' [-Werror=implicit-function-declaration]
drivers/net/ipa/ipa_endpoint.c:1291:45: error: 'ENDPOINT_STOP_DMA_TIMEOUT' undeclared (first use in this function)
drivers/net/ipa/ipa_endpoint.c: In function 'ipa_endpoint_stop':
drivers/net/ipa/ipa_endpoint.c:1309:16: error: 'IPA_ENDPOINT_STOP_RX_RETRIES' undeclared (first use in this function)
These functions were removed in a series, merged in as
commit 33395f4a5c ("Merge branch 'net-ipa-kill-endpoint-stop-workaround'").
Remove them again so that the build works properly.
Fixes: 3793faad7b ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous commit made ipa_endpoint_stop() be a trivial wrapper
around gsi_channel_stop(). Since it no longer does anything
special, just open-code it in the three places it's used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only reason ipa_endpoint_stop() had a retry loop was that the
just-removed workaround required an IPA DMA command to occur between
attempts. The gsi_channel_stop() call that implements the stop does
its own retry loop, to cover a channel's transition from started to
stop-in-progress to stopped state.
Get rid of the unnecessary retry loop in ipa_endpoint_stop().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_stop(), a workaround is used for IPA version 3.5.1
where a 1-byte DMA request is issued between GSI channel stop
retries.
It turns out that this workaround is only required for IPA versions
3.1 and 3.2, and we don't support those. So remove the call to
ipa_endpoint_stop_rx_dma() in that function. That leaves that
function unused, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_stop(), for TX endpoints we set the number of retries
to 0. When we break out of the loop, retries being 0 means we return
EIO rather than the value of ret (which should be 0).
Fix this by using a non-zero retry count for both RX and TX
channels, and just break out of the loop after calling
gsi_channel_stop() for TX channels. This way only RX channels
will retry, and the retry count will be non-zero at the end
for TX channels (so the proper value gets returned).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 713b6ebb4c)
Signed-off-by: David S. Miller <davem@davemloft.net>
A "delay mode" feature was put in place to work around a problem
that was observed during development of the upstream IPA driver. It
used TX endpoint "delay mode" in order to prevent transmitting
packets toward the modem before it was ready.
A race condition that would explain the problem has long since been
fixed, and we have concluded that the "delay mode" feature is no
longer required. So get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new helper function that encapsulates enabling or disabling
suspend on an RX endpoint. It returns the previous state of the
endpoint (true means suspend mode was enabled).
Create another function that handles enabling or disabling delay mode
on a TX endpoint. Delay mode does not work correctly on IPA version
4.2, so we don't currently use it (and shouldn't).
We only set delay mode in one case, and although we don't expect an
endpoint to already be in delay mode, it doesn't really matter if it
was. So the delay function doesn't return a value.
Stop issuing warnings if the previous suspend or delay mode state
differs from what is expected.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ipa_endpoint_init_ctrl() so it returns the previous state
(whether suspend or delay mode was enabled) rather than indicating
whether the request caused a change in state. This makes it easier
to understand what's happening where called.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places, a Boolean flag is used in the GSI code to
indicate whether the "doorbell engine" should be enabled or not
when a channel is configured. This is basically done to abstract
this property from the IPA version; the GSI code doesn't otherwise
"know" what the IPA hardware version is. The doorbell engine is
enabled only for IPA v3.5.1, not for IPA v4.0 and later.
The next patch makes another change that affects behavior during
channel reset (which also involves programming the channel). It
also distinguishes IPA v3.5.1 hardware from newer hardware.
Rather than creating another flag whose value matches the "db_enable"
value, just rename "db_enable" to be "legacy" so it can be used to
signal more than just the special doorbell handling.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
