The pm_ptr() macro should be used when the suspend and resume functions
can be compiled independently of the CONFIG_PM Kconfig option.
In the case of this driver, the suspend and resume functions are inside
a section protected by a #ifdef CONFIG_PM guard. Therefore pm_ptr()
should not be used.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It seems only XID 609 made it to the mass market. Therefore let's
disable detection of the other RTL8125a XID's. If nobody complains
we can remove support for RTL_GIGA_MAC_VER_60 later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2cd3df01-5f8b-08dd-6def-3f31a3014bde@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The original changes brakes MAC address assignment on older chip
versions (see bug report [0]), and it brakes random MAC assignment.
is_valid_ether_addr() requires that its argument is word-aligned.
Add the missing alignment to array mac_addr.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=215087
Fixes: 1c5d09d587 ("ethernet: r8169: use eth_hw_addr_set()")
Reported-by: Richard Herbert <rherbert@sympatico.ca>
Tested-by: Richard Herbert <rherbert@sympatico.ca>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->gso_max_segs is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add netif_set_gso_max_segs() helper.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->gso_max_size is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_size()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems this chip version never made it to the wild. Therefore
disable detection and if nobody complains remove support completely
later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems this chip version never made it to the wild. Therefore
disable detection and if nobody complains remove support completely
later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems these chip versions never made it to the wild. Therefore
disable detection and if nobody complains remove support completely
later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With newer chip versions ASPM-related issues seem to occur only if
L1.2 is enabled. I have a test system with RTL8168h that gives a
number of rx_missed errors when running iperf and L1.2 is enabled.
With L1.2 disabled (and L1 + L1.1 active) everything is fine.
See also [0]. Can't test this, but L1 + L1.1 being active should be
sufficient to reach higher package power saving states.
[0] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1942830
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/36feb8c4-a0b6-422a-899c-e61f2e869dfe@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch makes the driver r8169 pick up device Realtek Semiconductor Co.
, Ltd. Device [10ec:8162].
Signed-off-by: Janghyub Seo <jhyub06@gmail.com>
Suggested-by: Rushab Shah <rushabshah32@gmail.com>
Link: https://lore.kernel.org/r/1635231849296.1489250046.441294000@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a follow-up to beb401ec50 ("r8169: deprecate support for
RTL_GIGA_MAC_VER_27") that came with 5.12. Nobody complained, so let's
remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a function for what has been magic register writes so far.
It's based on recent changes to vendor drivers r8101, r8168, r8125,
and deals with events that trigger an early ASPM L1 exit.
Description of the bits has been kindly provided by Realtek.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ASPM is disabled completely because we've seen different types of
problems in the past. However it seems these problems occurred with
L1 or L1 sub-states only. On all the chip versions I've seen the
acceptable L0s exit latency is 512ns. This should be short enough not
to cause problems. If the actual L0s exit latency of the PCIe link
is bigger than 512ns then the PCI core will disable L0s anyway.
So let's give it a try and disable L1 and L1 sub-states only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the function to reflect what it's doing. Also add a description
of the register values as kindly provided by Realtek.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original L0 and L1 entrance latencies of RTL8106e are 4us. And
they cause the delay of link-up interrupt when enabling ASPM. Change
the L0 entrance latency to 7us and L1 entrance latency to 32us. Then,
they could avoid the issue.
Tested-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1ee8856de8.
This is used to re-enable ASPM on RTL8106e, if it is possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering the MDIO bus for a r8169 device, we use the PCI
bus/device specifier as a (seemingly) unique device identifier.
However the very same BDF number can be used on another PCI segment,
which makes the driver fail probing:
[ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003)
[ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700'
....
[ 27.684858] libphy: mii_bus r8169-700 failed to register
[ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22
Add the segment number to the device name to make it more unique.
This fixes operation on ARM N1SDP boards, with two boards connected
together to form an SMP system, and all on-board devices showing up
twice, just on different PCI segments. A similar issue would occur on
large systems with many PCI slots and multiple RTL8169 NICs.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
[Andre: expand commit message, use pci_domain_nr()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that on RTL8106e the link-up interrupt may be
significantly delayed if the user enables ASPM L1. Per default ASPM
is disabled. The change leaves L1 enabled on the PCIe link (thus still
allowing to reach higher package power saving states), but the
NIC won't actively trigger it.
Reported-by: Koba Ko <koba.ko@canonical.com>
Tested-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210528202327.GA39994@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove own module name definition and use KBUILD_MODNAME instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if the user changes the pause settings, the default settings
will be restored after an interface down/up cycle, and also when
resuming from suspend. This doesn't seem to provide the best user
experience. Change this to keep user settings, and just ensure that in
jumbo mode pause is disabled.
Small drawback: When switching back mtu from jumbo to non-jumbo then
pause remains disabled (but user can enable it using ethtool).
I think that's a not too common scenario and acceptable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It has been reported [0] that using pause frames in jumbo mode impacts
performance. There's no available chip documentation, but vendor
drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's
do the same, according to Roman it fixes the issue.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=212617
Fixes: 9cf9b84cc7 ("r8169: make use of phy_set_asym_pause")
Reported-by: Roman Mamedov <rm+bko@romanrm.net>
Tested-by: Roman Mamedov <rm+bko@romanrm.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the [g|s]et_pauseparam ethtool ops. It considers
that the chip doesn't support pause frame use in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new mac_managed_pm flag to indicate that the driver takes care
of PHY power management.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the N2100, instead of just marking the r8169 chips as having
broken_parity_status, disable parity error reporting for them entirely.
This was the only relevant place that set broken_parity_status, so we no
longer need to check for it in the r8169 error interrupt handler.
[bhelgaas: squash into one patch, commit log]
Link: https://lore.kernel.org/r/20210330174318.1289680-4-helgaas@kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
We can simply use rtl_hw_start_8168c_2() also for chip version 21.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool get_ringparam operation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOMMU errors have been reported if WoL is enabled and interface is
brought down. It turned out that the network chip triggers DMA
transfers after the DMA buffers have been freed. For WoL to work we
need to leave rx enabled, therefore simply stop the chip from being
a DMA busmaster.
Fixes: 567ca57faa ("r8169: add rtl8169_up")
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the lower_32_bits/upper_32_bits macros to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The (0xBAF70000 & 0x00FFF000) << 6 should be (0xf70 << 18).
Fixes: 561535b0f2 ("r8169: fix OCP access on RTL8117")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use macro pm_ptr(), this helps to avoid some ifdeffery.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleaning up tx descriptors first increases the chance that
rtl_rx() can allocate new skb's from the cache.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several years ago these two entries have been added, but it's not clear
why. There's no trace that there has ever been such a chip version, and
not even the r8101 vendor driver knows these id's. So let's disable
detection, and if nobody complains remove them completely later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we don't re-configure WOL-related register bits when waking up
from hibernation. I'm not aware of any problem reports, but better
play safe and call __rtl8169_set_wol() in the resume() path too.
To achieve this move calling __rtl8169_set_wol() to
rtl8169_net_resume() and rename the function to rtl8169_runtime_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no benefit in trying to disable interrupts if NAPI is
scheduled already. This allows us to save a PCI write in this case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/78c7f2fb-9772-1015-8c1d-632cbdff253f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the vendor driver, the new chip with XID 0x54b is
essentially the same as the one with XID 0x54a, but it doesn't need the
firmware.
So add support accordingly.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210202044813.1304266-1-kai.heng.feng@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far phy_disconnect() is called before free_irq(). If CONFIG_DEBUG_SHIRQ
is set and interrupt is shared, then free_irq() creates an "artificial"
interrupt by calling the interrupt handler. The "link change" flag is set
in the interrupt status register, causing phylib to eventually call
phy_suspend(). Because the net_device is detached from the PHY already,
the PHY driver can't recognize that WoL is configured and powers down the
PHY.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/fe732c2c-a473-9088-3974-df83cfbd6efd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was reported that on RTL8125 network breaks under heavy UDP load,
e.g. torrent traffic ([0], from comment 27). Realtek confirmed a hw bug
and provided me with a test version of the r8125 driver including a
workaround. Tests confirmed that the workaround fixes the issue.
I modified the original version of the workaround to meet mainline
code style.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=209839
v2:
- rebased to net
v3:
- make rtl_skb_is_udp() more robust and use skb_header_pointer()
to access the ip(v6) header
v4:
- remove dependency on ptp_classify.h
- replace magic number with offsetof(struct udphdr, len)
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Tested-by: xplo <xplo.bn@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/6e453d49-1801-e6de-d5f7-d7e6c7526c8f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtl_wol_enable_rx() is called via the following call chain if WoL
is enabled:
rtl8169_down()
-> rtl_prepare_power_down()
-> rtl_wol_enable_rx()
Therefore we don't have to call this function here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/34ce78e2-596c-e2ac-16aa-c550fa624c22@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of doing the full DASH check each time r8168_check_dash() is
called, let's do it once in probe and store DASH capabilities in a
new rtl8169_private member.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the mask to include the checksum failure bits. This allows to
simplify the condition in rtl8169_rx_csum().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At least from chip version 25 the vendor driver sets these rx flags
for all chip versions if WOL is enabled. Therefore I wouldn't consider
it a quirk, so let's rename the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clean up the remainings of rtl_pll_power_down/up and rename
rtl_pll_power_down() to rtl_prepare_power_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek provided a description of bits 6 and 7 in register PMCH.
They configure whether the chip powers down certain PLL in D3hot and
D3cold respectively. They do not actually power down the PLL.
Reflect this in the code and configure D3 PLL powerdown based on
whether WOL is enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no known reason why PLL powerdown on D3 shouldn't be enabled
on chip versions 34, 35, 36, and 42. At least the vendor driver doesn't
exclude any of these chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far we don't increase the max read request size if we switch to
jumbo mode before bringing up the interface for the first time.
Let's change this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Align behavior with r8168 vendor driver and don't reduce max read
request size for RTL8168e in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8168dp is ancient anyway, and I haven't seen any trace of its early
version 27 yet. This chip versions needs quite some special handling,
therefore it would facilitate driver maintenance if support for it
could be dropped. For now just disable detection of this chip version.
If nobody complains we can remove support for it in the near future.
v2:
- extend unknown chip version error message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/ca98f018-a0e1-8762-e95c-f0ad773a0271@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If WOL isn't enabled, then there's no need to enable wakeup from D3
on system shutdown.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN_ONCE here to get a call trace in case of a problem.
This facilitates finding the offending code part.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN here to avoid stopping the system. In addition print the addr
and mask values that triggered the warning.
v2:
- return on WARN to avoid an invalid register write
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to Realtek the ERI register 0x1a8 quirk is needed to work
around a hw issue with the PHY on RTL8168g. The register needs to be
changed before powering down the PHY. Currently we don't meet this
requirement, however I'm not aware of any problems caused by this.
Therefore I see the change as an improvement.
The PHY driver has no means to access the chip ERI registers,
therefore we have to intercept MDIO writes to BMCR register.
If the BMCR_PDOWN bit is going to be set, then let's apply the
quirk before actually powering down the PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No functional change here. We just move a code block to avoid a
function forward declaration in a subsequent change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A user reported failing network with RTL8168dp (a quite rare chip
version). Realtek confirmed that few chip versions suffer from a PLL
power-down hw bug.
Fixes: 07df5bd874 ("r8169: power down chip in probe")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a1c39460-d533-7f9e-fa9d-2b8990b02426@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent changes there's no need any longer to define NUM_RX_DESC
as an unsigned value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to check min(budget, NUM_RX_DESC). At first budget
(NAPI_POLL_WEIGHT = 64) is less then NUM_RX_DESC (256).
And more important: Even in case of budget > NUM_RX_DESC we could
safely continue processing descriptors as long as they are owned by
the CPU. In addition replace rx_left with a normal counter variable,
this allows to simplify the code. Last but not least there's no need
any longer to pass the budget as an u32.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On chip versions supporting tally counter reset we currently update
the counters after a reset although we know all counters are zero.
Skip this unnecessary step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/526618b2-b1bf-1844-b82a-dab2df7bdc8f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some chip versions have a hw bug resulting in lost door bell rings.
To work around this the doorbell is also rung whenever we still have
tx descriptors in flight after having cleaned up tx descriptors.
These PCI(e) writes come at a cost, therefore let's reduce the number
of extra doorbell rings.
If skb is NULL then this means:
- last cleaned-up descriptor belongs to a skb with at least one fragment
and last fragment isn't marked as sent yet
- hw is in progress sending the skb, therefore no extra doorbell ring
is needed for this skb
- once last fragment is marked as transmitted hw will trigger
a tx done interrupt and we come here again (with skb != NULL)
and ring the doorbell if needed
Therefore skip the workaround doorbell ring if skb is NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/0a15a83c-aecf-ab51-8071-b29d9dcd529a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rtl_tx() the released descriptors are zero'ed by
rtl8169_unmap_tx_skb(). And in the beginning of rtl8169_start_xmit()
we check that enough descriptors are free, therefore there's no way
the DescOwn bit can be set here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/6965d665-6c50-90c5-70e6-0bb335d4ea47@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only time when nr_frags isn't SKB_MAX_FRAGS is when entering
rtl8169_start_xmit(). However we can use SKB_MAX_FRAGS also here
because when queue isn't stopped there should always be room for
MAX_SKB_FRAGS + 1 descriptors.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/3d1f2ad7-31d5-2cac-4f4a-394f8a3cab63@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Improve the following in rtl8169_start_xmit:
- tp->cur_tx can be accessed in parallel by rtl_tx(), therefore
annotate the race by using WRITE_ONCE
- avoid checking stop_queue a second time by moving the doorbell check
- netif_stop_queue() uses atomic operation set_bit() that includes a
full memory barrier on some platforms, therefore use
smp_mb__after_atomic to avoid overhead
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/80085451-3eaf-507a-c7c0-08d607c46fbc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can simplify the for() condition and eliminate variable tx_left.
The change also considers that tp->cur_tx may be incremented by a
racing rtl8169_start_xmit().
In addition replace the write to tp->dirty_tx and the following
smp_mb() with an equivalent call to smp_store_mb(). This implicitly
adds a WRITE_ONCE() to the write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/c2e19e5e-3d3f-d663-af32-13c3374f5def@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tp->dirty_tx and tp->cur_tx may be changed by a racing rtl_tx() or
rtl8169_start_xmit(). Use READ_ONCE() to annotate the races and ensure
that the compiler doesn't use cached values.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/5676fee3-f6b4-84f2-eba5-c64949a371ad@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8125B has same or similar short packet hw padding bug as RTL8168evl.
The main workaround has been extended accordingly, however we have to
disable also hw checksumming for short packets on affected new chip
versions. Instead of checking for an affected chip version let's
simply disable hw checksumming for short packets in general.
v2:
- remove the version checks and disable short packet hw csum in general
- reflect this in commit title and message
Fixes: 0439297be9 ("r8169: add support for RTL8125B")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7fbb35f0-e244-ef65-aa55-3872d7d38698@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The caller of rtl8169_tso_csum_v2() frees the skb if false is returned.
eth_skb_pad() internally frees the skb on error what would result in a
double free. Therefore use __skb_put_padto() directly and instruct it
to not free the skb on error.
Fixes: b423e9ae49 ("r8169: fix offloaded tx checksum for small packets.")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/f7e68191-acff-9ded-4263-c016428a8762@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Network problems with RTL8125B have been reported [0] and with help
from Realtek it turned out that this chip version has a hw problem
with short packets (similar to RTL8168evl). Having said that activate
the same workaround as for RTL8168evl.
Realtek suggested to activate the workaround for RTL8125A too, even
though they're not 100% sure yet which RTL8125 versions are affected.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=209839
Fixes: 0439297be9 ("r8169: add support for RTL8125B")
Reported-by: Maxim Plotnikov <wgh@torlan.ru>
Tested-by: Maxim Plotnikov <wgh@torlan.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8002c31a-60b9-58f1-f0dd-8fd07239917f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We had to remove flag IRQF_NO_THREAD because it conflicts with shared
interrupts in case legacy interrupts are used. Following up on the
linked discussion set IRQF_NO_THREAD if MSI or MSI-X is used, because
both guarantee that interrupt won't be shared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://www.spinics.net/lists/netdev/msg695341.html
Link: https://lore.kernel.org/r/446cf5b8-dddd-197f-cb96-66783141ade4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lowest number of tx descriptors used in the vendor drivers is 256 in
r8169. r8101/r8168/r8125 use 1024 what seems to be the hw limit. Stay
on the safe side and go with 256, same as number of rx descriptors.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a52a6de4-f792-5038-ae2f-240d3b7860eb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can safely runtime-suspend the chip if rtl_open() fails. Therefore
switch the error path to use pm_runtime_put_sync() as well.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/aa093b1e-f295-5700-1cb7-954b54dd8f17@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tp->dirty_tx isn't changed outside rtl_tx(). Therefore I see no need
to guarantee a specific order of reading tp->dirty_tx and tp->cur_tx.
Having said that we can remove the memory barrier.
In addition use READ_ONCE() when reading tp->cur_tx because it can
change in parallel to rtl_tx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2264563a-fa9e-11b0-2c42-31bc6b8e2790@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After switching to the net core rx/tx byte/packet counters we can
remove the now unused private version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch to the net core rx/tx byte/packet counter infrastructure.
This simplifies the code, only small drawback is some memory overhead
because we use just one queue, but allocate the counters per cpu.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported by Serge flag IRQF_NO_THREAD causes an error if the
interrupt is actually shared and the other driver(s) don't have this
flag set. This situation can occur if a PCI(e) legacy interrupt is
used in combination with forced threading.
There's no good way to deal with this properly, therefore we have to
remove flag IRQF_NO_THREAD. For fixing the original forced threading
issue switch to napi_schedule().
Fixes: 424a646e07 ("r8169: fix operation under forced interrupt threading")
Link: https://www.spinics.net/lists/netdev/msg694960.html
Reported-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Link: https://lore.kernel.org/r/b5b53bfe-35ac-3768-85bf-74d1290cf394@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For several network drivers it was reported that using
__napi_schedule_irqoff() is unsafe with forced threading. One way to
fix this is switching back to __napi_schedule, but then we lose the
benefit of the irqoff version in general. As stated by Eric it doesn't
make sense to make the minimal hard irq handlers in drivers using NAPI
a thread. Therefore ensure that the hard irq handler is never
thread-ified.
Fixes: 9a899a35b0 ("r8169: switch to napi_schedule_irqoff")
Link: https://lkml.org/lkml/2020/10/18/19
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/4d3ef84a-c812-5072-918a-22a6f6468310@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Factor out handling the private packet/byte counters to new
functions rtl_get_priv_stats() and rtl_inc_priv_stats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that system freezes on r8169 driver load on a system
using ether_clk. The original change was done under the assumption
that the clock isn't needed for basic operations like chip register
access. But obviously that was wrong.
Therefore effectively revert the original change, and in addition
leave the clock active when suspending and WoL is enabled. Chip may
not be able to process incoming packets otherwise.
Fixes: 9f0b54cd16 ("r8169: move switching optional clock on/off to pll power functions")
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mistakenly bit 2 was set instead of bit 3 as in the vendor driver.
Fixes: a7a92cf815 ("r8169: sync PCIe PHY init with vendor driver 8.047.01")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After making use of the gro_flush_timeout attribute I once got a
tx timeout due to an interrupt that wasn't handled. Seems using
irq_enabled can be racy, and it's not needed any longer anyway,
so remove it. I've never seen a report about such a race before,
therefore treat the change as an improvement.
There's just one small drawback: If a legacy PCI interrupt is used,
and if this interrupt is shared with a device with high interrupt
rate, then we may handle interrupts even if NAPI disabled them,
and we may see a certain performance decrease under high network load.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the return value of napi_complete_done(), this allows users to
use the gro_flush_timeout sysfs attribute as an alternative to classic
interrupt coalescing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most chip versions this has been added already. Allow also for
RTL8125A to enable ASPM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTL8125B rev.b. In my tests 2.5Gbps worked well
w/o firmware, however for a stable link at 1Gbps firmware revision
0.0.2 is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two managed helpers for mdiobus - devm_mdiobus_alloc()
and devm_mdiobus_register(). The idea behind devres is that the release
callback releases whatever resource the devm function allocates. In the
mdiobus case however there's no devres associated with the device by
devm_mdiobus_register(). Instead the release callback for
devm_mdiobus_alloc(): _devm_mdiobus_free() unregisters the device if
it is marked as managed.
This all seems wrong. The managed structure shouldn't need to know or
care about whether it's managed or not - and this is the case now for
struct mii_bus. The devres wrapper should be opaque to the managed
resource.
This changeset makes devm_mdiobus_alloc() and devm_mdiobus_register()
conform to common devres standards: devm_mdiobus_alloc() allocates a
devres structure and registers a callback that will call mdiobus_free().
__devm_mdiobus_register() allocated another devres and registers a
callback that will unregister the bus.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far RTL8401 was treated like a RTL8101e, means we relied on the BIOS
to configure MAC and PHY properly. Make RTL8401 a separate chip version
and copy MAC / PHY config from r8101 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip versions 13, 14, 15 are treated the same by the driver, therefore
let's merge them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek added new members to the RTL8125 chip family, therefore rename
RTL8125 to RTL8125a. Then we use the same chip naming as in the r8125
vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify rtl8169_runtime_resume() by calling rtl8169_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the critical sections are protected with RTNL lock, we don't
need a separate mutex any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most relevant ops (open, close, ethtool ops) are protected with RTNL
lock by net core. Make sure that such ops can't be interrupted by
e.g. (runtime-)suspending by taking the RTNL lock in suspend ops
and the PCI error handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out bringing device up to a new function rtl8169_up(), similar
to rtl8169_down() for bringing the device down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the netdevice is marked as detached now when parent is not
accessible we can remove quite some checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark the netdevice as detached whenever we go into PCI D3hot.
This allows to remove some checks e.g. from ethtool ops because
dev_ethtool() checks for netif_device_present() in the beginning.
In this context move waking up the queue out of rtl_reset_work()
because in cases where netif_device_attach() is called afterwards
the queue should be woken up by the latter function only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically the firmware takes care that tp->ocp_base is reset to its
default value. That's not the case (at least) for RTL8117.
As a result subsequent PHY access reads/writes the wrong page and
the link is broken. Fix this be resetting tp->ocp_base explicitly.
Fixes: 229c1e0dfd ("r8169: load firmware for RTL8168fp/RTL8117")
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we can not configure irq coalescing when link is down. Allow the
user to do this, and assume that he wants to configure irq coalescing
for highest speed. Otherwise the irq rate is low enough anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relevant chip clocks are disabled in rtl_pll_power_down(), therefore
move calling clk_disable_unprepare() there. Similar for enabling the
clock.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Counters are updated whenever we go down, therefore move the call to
rtl8169_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_hw_reset() meanwhile does more than a hw reset, therefore rename
it to rtl8169_cleanup(). In addition move calling napi_disable() to this
function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_hw_reset() may be called under RTNL lock, therefore switch to
synchronize_net().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following scenario WoL isn't configured properly:
- Driver is loaded, interface isn't brought up within 10s, so driver
runtime-suspends.
- WoL is set.
- Interface is brought up, stored WoL setting isn't applied.
It has always been like that, but the scenario seems to be quite
theoretical as I haven't seen any bug report yet. Therefore treat
the change as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 9d3679fe0f ("r8169: inline rtl8169_make_unusable_by_asic")
this constant isn't used any longer, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of problems it facilitates the bug analysis if we know whether
DASH is active. Therefore emit a message in probe if this is the case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Th referenced change added an extra hw reset to rtl8169_net_suspend()
what makes WoL fail on few chip versions. Therefore skip the extra
reset if we're going down and WoL is enabled.
In rtl_shutdown() rtl8169_hw_reset() is called by rtl8169_net_suspend()
already if needed, therefore avoid issues issue by removing the extra
call. The fix was tested on a system with RTL8168g.
Meanwhile rtl8169_hw_reset() does more than a hw reset and should be
renamed. But that's net-next material.
Fixes: 8ac8e8c64b ("r8169: make rtl8169_down central chip quiesce function")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify handling the power management callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functionality for quiescing the chip is spread across different
functions currently. Move it to rtl8169_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calls that are needed before and after calling rtl8169_hw_reset()
into this function. This requires to move the function in the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In places where the indexes have to be reset, we call
rtl8169_init_ring_indexes() anyway after rtl8169_tx_clear().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We go to runtime-suspend few secs after cable removal. As cable is
removed "physical link up" is the only meaningful WoL source.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change driver private data type to struct rtl8169_private * to avoid
some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call netif_napi_del() manually, free_netdev() does this for us.
In addition reorder calls to match reverse order of calls in probe().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168f/RTL8411 with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168evl with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168h with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168g with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the mask argument as it's not used by r8168ep_ocp_read().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers read the full 32bit value, therefore the mask argument can
be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_eri_read() returns the full 32bit value, therefore there's no
benefit in writing back parts of it only. handle it like the vendor
driver and write the full 32 bit always. Omitting the mask argument
avoids some overhead and makes the code better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to r8168 vendor driver DASHv3 chips like RTL8168fp/RTL8117
need a special addressing for OCP access.
Fix is compile-tested only due to missing test hardware.
Fixes: 1287723aa1 ("r8169: add support for RTL8117")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In [0] a user reported reproducible tx timeouts on RTL8168f except
PktCntrDisable is set and irq coalescing is enabled.
Realtek told me that they are not aware of any related hw issue on
this chip version, therefore root cause is still unknown. It's not
clear whether the issue affects one or more chip versions in general,
or whether issue is specific to reporter's system.
Due to this level of uncertainty, and due to the fact that I'm aware
of this one report only, let's apply the workaround on net-next only.
After this change setting irq coalescing via ethtool can reliably
avoid the issue on the affected system.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=207205
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the compiler decide about inlining, and as confirmed by Eric it's
better to use WRITE_ONCE here to ensure that the descriptor ownership
is transferred to NIC immediately.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the goto from the rx error handling branch into the else branch,
and in general avoid having the main rx work in the else branch.
In addition ensure proper reverse xmas tree order of variables in the
for loop.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After having switched to devm_mdiobus_register() also this remaining
call to mdiobus_unregister() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
93882c6f21 ("r8169: switch from netif_xxx message functions to
netdev_xxx") removed the last module parameter from the driver,
therefore there's no need any longer to include linux/moduleparam.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 9de5d235b6 ("net: phy: fix aneg restart in phy_ethtool_set_eee")
we don't need the check for aneg being enabled any longer, and as
discussed with Russell configuring the EEE advertisement should be
supported even if we're in a half-duplex mode currently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync the reset preparation for chips from RTL8168g with the r8168 and
r8125 vendor drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for waiting for FIFO's to be empty, again the name is
borrowed from the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for setting RXDV_GATED_EN, the 2ms delay is copied from
the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a helper for this waiting function, name of the helper is
borrowed from the vendor driver. In addition don't return in the two
hw_init functions if the first wait runs into a timeout, there's no
benefit in doing so.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
r8169 never had native support for the RTL8401, however it reportedly
worked with the fallback to RTL8101e [0]. Therefore let's add this
as an explicit assignment.
[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=956868
Fixes: b4cc2dcc9c ("r8169: remove default chip versions")
Reported-by: Camaleón <noelamac@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new flexible sleep function fsleep() to merge the udelay and msleep
polling functions. We can safely do this because no polling function
is used in atomic context in this driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper eth_hw_addr_crc to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering the few messages we have in the driver, there's not really
a benefit in being able to control them on a message type level.
Therefore simplify the code and switch to the netdev_xxx message
functions. In addition add net_ratelimit() to messages that can be
printed from a hot path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When preparing an unrelated change, checkpatch complained about this
redundant out-of-memory message. Therefore remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter handling functions can only fail if rtl8169_do_counters()
times out. In the poll function we emit an error message in case of
timeout, therefore we don't have to propagate the timeout all the
way up just to print another message basically saying the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net core - __dev_set_promiscuity - prints a message already when
promiscuous mode in entered/left, therefore we don't have to do this
in the driver too. Also the driver message would be misleading
(would be because "link" message level is disabled per default)
because it would print "promisc mode enabled" even if it's being
left. Reason is that __dev_change_flags() calls dev_set_rx_mode()
before touching the promisc flag.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a not needed parameter in rtl8169_set_magic_reg.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 supports the same PME_SIGNAL handling as all later RTL8168
chip variants.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync definition of max jumbo packet size with vendor driver and reserve
22 bytes for VLAN ethernet header plus checksum.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek provided information about a HW constraint that time limit must
not be set to 0 if the frame limit is >0. Add a check for this and
reject invalid parameter combinations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_PREP() to make the code better readable, and avoid the loop.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports only frame limits 0, 4, 8, .. 60 internally.
Returning EINVAL for all val % 4 != 0 seems to be a little bit too
unfriendly to the user. Therefore round up the frame limit to the next
supported value. In addition round up the time limit, else a very low
limit could be rounded down to 0, and interpreted as "ignore value"
by the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time limit provided by userspace is multiplied with 1000,
what could result in an overflow. Therefore change the time limit
parameter unit from ns to us, and avoid the problematic operation.
If there's no matching scale because provided time limit is too big,
return ERANGE instead of EINVAL to provide a hint to the user what's
wrong.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_GET() macro to make the code better readable. In addition
change the logic to round the time limit up, not down. Reason is that
a time limit <1us would be rounded to 0 currently, what would be
interpreted as "no time limit set".
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx and tx scale are the same always. Simplify the code by using one
scale for rx and tx only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_device argument is just used to get a struct rtl8169_private
pointer via netdev_priv(). Therefore pass the struct rtl8169_private
pointer directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of consumer mainboards where the BIOS leaves the PHY
in a state that it's reporting an invalid PHY ID. To detect such cases
add the PHY ID to the error message if no dedicated PHY driver is found.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two bits in RxConfig are controlled by the following dev->feature's:
- NETIF_F_RXALL
- NETIF_F_HW_VLAN_CTAG_RX (since RTL8125)
We have to take care that RxConfig gets fully configured in
rtl_hw_start() after e.g. resume from hibernation. Therefore:
- Factor out setting the feature-controlled RxConfig bits to a new
function rtl_set_rx_config_features() that is called from
rtl8169_set_features() and rtl_hw_start().
- Don't deal with RX_VLAN_8125 in rtl_init_rxcfg(), it will be set
by rtl_set_rx_config_features().
- Don't handle NETIF_F_RXALL in rtl_set_rx_mode().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's sufficient to do the masking once in probe() for clearing
unwanted bits that may have been set by the BIOS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A barrier is needed here to ensure that rtl_tx sees the descriptor
changes (DescOwn set) before the updated tp->cur_tx value. Else it may
wrongly assume that the transfer has been finished already. For this
purpose smp_wmb() is sufficient.
No separate barrier is needed for ordering the descriptor changes
with the MMIO doorbell write. The needed barrier is included in
the non-relaxed writel() used by rtl8169_doorbell().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline rtl8169_make_unusable_by_asic() and simplify it:
- Address field doesn't need to be poisoned because descriptor is
owned by CPU now
- desc->opts1 is set by rtl8169_mark_to_asic() and rtl8169_rx_fill(),
therefore we don't have to preserve any field parts.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_mark_as_last_descriptor() has just one user, so inline it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Realtek PHY driver takes care of adding the needed delay now,
therefore we can remove the delay here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround for hw issues with TSO on RTL8168evl. This workaround is
based on information I got from Realtek, and *should* allow to safely
enable TSO on this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and avoid the overhead of calling vlan_get_protocol().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At that place in rtl_init_one() we can safely use rtl8169_set_features()
to configure the chip according to the default features.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we set RX_VLAN_8125 unconditionally, even if
NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits,
and let only rtl8169_set_features() control them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HIGHDMA is added to vlan_features by register_netdev(),
therefore we can omit this here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting the ocp_base to rtl_init_one(). Where supported the value
is always the same, and if not supported it doesn't hurt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been a number of reports that using SG/TSO on different chip
versions results in tx timeouts. However for a lot of people SG/TSO
works fine. Therefore disable both features by default, but allow users
to enable them. Use at own risk!
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out mapping the tx skb to a new function rtl8169_tx_map(). This
allows to remove redundancies, and rtl8169_get_txd_opts1() has only
one user left, so it can be inlined.
As a result rtl8169_xmit_frags() is significantly simplified, and in
rtl8169_start_xmit() the code is simplified and better readable.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mtu is greater than TD_MSS_MAX, then TSO is disabled, see
rtl8169_fix_features(). Because mss is less than mtu, we can't have
the case mss > TD_MSS_MAX in the TSO path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rtl_task() is designed to handle a large number of tasks.
However we have just one, so we can remove some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
