Use libie_aq_desc instead of ixgbe_aci_desc. Do needed changes to allow
clean build.
Move additional caps used in ixgbe to libie.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add E610 implementation of fw_recovery_mode MAC operation.
In case of E610 information about recovery mode is obtained
from FW_MODES field in IXGBE_GL_MNG_FWSM register (0x000B6134).
Introduce recovery specific probing flow and init only
vital features.
User should be able to perform NVM update using devlink
once FW error is detected in order to load a healthy img.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The E610 adapters contain an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the pldmfw library to implement device flash update for
the Intel ixgbe networking device driver specifically for E610 devices.
This support uses the devlink flash update interface.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset.
With this implementation, basic flash update for the E610 hardware is
supported.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Co-developed-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Co-developed-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Stefan Wegrzyn <stefan.wegrzyn@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
