Newer firmware for the E810 devices support a 'low latency' interface to
interact with the PHY without using the Admin Queue. This is interacted
with via the REG_LL_PROXY_L and REG_LL_PROXY_H registers.
Currently, this interface is only used for Tx timestamps. There are two
different mechanisms, including one which uses an interrupt for firmware to
signal completion. However, these two methods are mutually exclusive, so no
synchronization between them was necessary.
This low latency interface is being extended in future firmware to support
also programming the PHY timers. Use of the interface for PHY timers will
need synchronization to ensure there is no overlap with a Tx timestamp.
The interrupt-based response complicates the locking somewhat. We can't use
a simple spinlock. This would require being acquired in
ice_ptp_req_tx_single_tstamp, and released in
ice_ptp_complete_tx_single_tstamp. The ice_ptp_req_tx_single_tstamp
function is called from the threaded IRQ, and the
ice_ptp_complete_tx_single_stamp is called from the low latency IRQ, so we
would need to acquire the lock with IRQs disabled.
To handle this, we'll use a wait queue along with
wait_event_interruptible_locked_irq in the update flows which don't use the
interrupt.
The interrupt flow will acquire the wait queue lock, set the
ATQBAL_FLAGS_INTR_IN_PROGRESS, and then initiate the firmware low latency
request, and unlock the wait queue lock.
Upon receipt of the low latency interrupt, the lock will be acquired, the
ATQBAL_FLAGS_INTR_IN_PROGRESS bit will be cleared, and the firmware
response will be captured, and wake_up_locked() will be called on the wait
queue.
The other flows will use wait_event_interruptible_locked_irq() to wait
until the ATQBAL_FLAGS_INTR_IN_PROGRESS is clear. This function checks the
condition under lock, but does not hold the lock while waiting. On return,
the lock is held, and a return of zero indicates we hold the lock and the
in-progress flag is not set.
This will ensure that threads which need to use the low latency interface
will sleep until they can acquire the lock without any pending low latency
interrupt flow interfering.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The TS_LL_READ macros are used as part of the low latency Tx timestamp
interface. A future firmware extension will add support for performing PHY
timer updates over this interface. Using TS_LL_READ as the prefix for these
macros will be confusing once the interface is used for other purposes.
Rename the macros, using the prefix REG_LL_PROXY_H, to better clarify that
this is for the low latency interface.
Additionally add macros for PF_SB_ATQBAH and PF_SB_ATQBAL registers to
better clarify content of this registers as PF_SB_ATQBAH contain low
part of Tx timestamp
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_read_phy_tstamp_ll_e810 function repeatedly reads the PF_SB_ATQBAL
register until the TS_LL_READ_TS bit is cleared. This is a perfect
candidate for using rd32_poll_timeout. However, the default implementation
uses a sleep-based wait. Use read_poll_timeout_atomic macro which is based
on the non-sleeping implementation and use it to replace the loop reading
in the ice_read_phy_tstamp_ll_e810 function.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use string choice helpers for better readability.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202410121553.SRNFzc2M-lkp@intel.com/
Signed-off-by: R Sundar <prosunofficial@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware generates events for global events or port specific events.
Driver shall subscribe for health status events from firmware on supported
FW versions >= 1.7.6.
Driver shall expose those under specific health reporter, two new
reporters are introduced:
- FW health reporter shall represent global events (problems with the
image, recovery mode);
- Port health reporter shall represent port-specific events (module
failure).
Firmware only reports problems when those are detected, it does not store
active fault list.
Driver will hold only last global and last port-specific event.
Driver will report all events via devlink health report,
so in case of multiple events of the same source they can be reviewed
using devlink autodump feature.
$ devlink health
pci/0000:b1:00.3:
reporter fw
state healthy error 0 recover 0 auto_dump true
reporter port
state error error 1 recover 0 last_dump_date 2024-03-17
last_dump_time 09:29:29 auto_dump true
$ devlink health diagnose pci/0000:b1:00.3 reporter port
Syndrome: 262
Description: Module is not present.
Possible Solution: Check that the module is inserted correctly.
Port Number: 0
Tested on Intel Corporation Ethernet Controller E810-C for SFP
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Sharon Haroni <sharon.haroni@intel.com>
Signed-off-by: Sharon Haroni <sharon.haroni@intel.com>
Co-developed-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Konrad Knitter <konrad.knitter@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The new recipe should be added even if exactly the same recipe already
exists with different priority.
Example use case is when the rule is being added from TC tool context.
It should has the highest priority, but if the recipe already exists
the rule will inherit it priority. It can lead to the situation when
the rule added from TC tool has lower priority than expected.
The solution is to check the recipe priority when trying to find
existing one.
Previous recipe is still useful. Example:
RID 8 -> priority 4
RID 10 -> priority 7
The difference is only in priority rest is let's say eth + mac +
direction.
Adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
After that IP + MAC_B + RX on RID 10 (from TC tool), forward to PF0
Both will work.
In case of adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
ARP + MAC_A + RX on RID 10, forward to PF0.
Only second one will match, but this is expected.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move ice_adapter initialization to be after HW init, so it could use HW
capabilities, like number of PFs. This is needed for devlink-resource
based RSS LUT size management for PF/VF (not in this series).
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clean up goto labels after previous commit, to conform to single naming
scheme in ice_probe() and ice_init_dev().
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Split ice_init_hw() call out from ice_init_dev(). Such move enables
pulling the former to be even earlier on call path, what would enable
moving ice_adapter init to be between the two (in subsequent commit).
Such move enables ice_adapter to know about number of PFs.
Do the same for ice_deinit_hw(), so the init and deinit calls could
be easily mirrored.
Next commit will rename unrelated goto labels to unroll prefix.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move call to ice_wait_for_fw() from ice_init_dev() into ice_init_hw(),
where it fits better. This requires also to move ice_wait_for_fw()
to ice_common.c.
ice_is_pf_c827() is now used only in ice_common.c, so it could be static.
CC: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Driver always naively assumes, that for PTP purposes, PHY lane to
configure is corresponding to PF ID.
This is not true for some port configurations, e.g.:
- 2x50G per quad, where lanes used are 0 and 2 on each quad, but PF IDs
are 0 and 1
- 100G per quad on 2 quads, where lanes used are 0 and 4, but PF IDs are
0 and 1
Use correct PHY lane assignment by getting and parsing port options.
This is read from the NVM by the FW and provided to the driver with
the indication of active port split.
Remove ice_is_muxed_topo(), which is no longer needed.
Fixes: 4409ea1726 ("ice: Adjust PTP init for 2x50G E825C devices")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Arkadiusz Kubalewski <Arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix ETH56G FC-FEC incorrect Rx offset value by changing it from -255.96
to -469.26 ns.
Those values are derived from HW spec and reflect internal delays.
Hex value is a fixed point representation in Q23.9 format.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Quad registers are read/written incorrectly. E825 devices always use
quad 0 address and differentiate between the PHYs by changing SBQ
destination device (phy_0 or phy_0_peer).
Add helpers for reading/writing PTP registers shared per quad and use
correct quad address and SBQ destination device based on port.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current implementation checks revision of all PHYs on all PFs, which is
incorrect and may result in initialization failure. Check only the
revision of the current PHY.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
ptp4l application reports too high offset when ran on E823 device
with a 100GB/s link. Those values cannot go under 100ns, like in a
working case when using 100 GB/s cable.
This is due to incorrect frequency settings on the PHY clocks for
100 GB/s speed. Changes are introduced to align with the internal
hardware documentation, and correctly initialize frequency in PHY
clocks with the frequency values that are in our HW spec.
To reproduce the issue run ptp4l as a Time Receiver on E823 device,
and observe the offset, which will never approach values seen
in the PTP working case.
Reproduction output:
ptp4l -i enp137s0f3 -m -2 -s -f /etc/ptp4l_8275.conf
ptp4l[5278.775]: master offset 12470 s2 freq +41288 path delay -3002
ptp4l[5278.837]: master offset 10525 s2 freq +39202 path delay -3002
ptp4l[5278.900]: master offset -24840 s2 freq -20130 path delay -3002
ptp4l[5278.963]: master offset 10597 s2 freq +37908 path delay -3002
ptp4l[5279.025]: master offset 8883 s2 freq +36031 path delay -3002
ptp4l[5279.088]: master offset 7267 s2 freq +34151 path delay -3002
ptp4l[5279.150]: master offset 5771 s2 freq +32316 path delay -3002
ptp4l[5279.213]: master offset 4388 s2 freq +30526 path delay -3002
ptp4l[5279.275]: master offset -30434 s2 freq -28485 path delay -3002
ptp4l[5279.338]: master offset -28041 s2 freq -27412 path delay -3002
ptp4l[5279.400]: master offset 7870 s2 freq +31118 path delay -3002
Fixes: 3a7496234d ("ice: implement basic E822 PTP support")
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Przemyslaw Korba <przemyslaw.korba@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask admin command returned max phase adjust value for both input and
output pins. Only 31 bits are relevant, last released data sheet wrongly
points that 32 bits are valid - see [1] 3.2.6.4.1 Get CCU Capabilities
Command for reference. Fix of the datasheet itself is in progress.
Fix the min/max assignment logic, previously the value was wrongly
considered as negative value due to most significant bit being set.
Example of previous broken behavior:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-get --json '{"id":1}'| grep phase-adjust
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
Correct behavior with the fix:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-get --json '{"id":1}'| grep phase-adjust
'phase-adjust': 0,
'phase-adjust-max': 2147466925,
'phase-adjust-min': -2147466925,
[1] https://cdrdv2.intel.com/v1/dl/getContent/613875?explicitVersion=true
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, xsk_buff_add_frag() only adds the frag to pool's linked list,
not doing anything with the &xdp_buff. The drivers do that manually and
the logic is the same.
Make it really add an skb frag, just like xdp_buff_add_frag() does that,
and freeing frags on error if needed. This allows to remove repeating
code from i40e and ice and not add the same code again and again.
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20241218174435.1445282-5-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a devlink health reporter for MDD events. The 'dump' handler will
return the information captured in each call to ice_handle_mdd_event().
A device reset (CORER/PFR) will put the reporter back in healthy state.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Co-developed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add Tx hang devlink health reporter, see struct ice_tx_hang_event to see
what exactly is reported. For now dump descriptors with little metadata
and skb diagnostic information.
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Co-developed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Drop "devlink_" prefix from files that sit in devlink/.
I'm going to add more files there, and repeating "devlink" does not feel
good. This is also the scheme used in most other places, most notably the
devlink core files are named like that.
devlink.[ch] stays as is.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_copy_rxq_ctx_to_hw() and ice_write_rxq_ctx() functions perform some
defensive checks which are typically frowned upon by kernel style
guidelines.
In particular, NULL checks on buffers which point to the stack are
discouraged, especially when the functions are static and only called once.
Checks of this sort only serve to hide potential programming error, as we
will not produce the normal crash dump on a NULL access.
In addition, ice_copy_rxq_ctx_to_hw() cannot fail in another way, so could
be made void.
Future support for VF Live Migration will need to introduce an inverse
function for reading Rx queue context from HW registers to unpack it, as
well as functions to pack and unpack Tx queue context from HW.
Rather than copying these style issues into the new functions, lets first
cleanup the existing code.
For the ice_copy_rxq_ctx_to_hw() function:
* Move the Rx queue index check out of this function.
* Convert the function to a void return.
* Use a simple int variable instead of a u8 for the for loop index, and
initialize it inside the for loop.
* Update the function description to better align with kernel doc style.
For the ice_write_rxq_ctx() function:
* Move the Rx queue index check into this function.
* Update the function description with a Returns: to align with kernel doc
style.
These changes align the existing write functions to current kernel
style, and will align with the style of the new functions added when we
implement live migration in a future series.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-10-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice_write_rxq_ctx() function is responsible for programming the Rx
Queue context into hardware. It receives the configuration in unpacked form
via the ice_rlan_ctx structure.
This function unconditionally modifies the context to set the prefetch
enable bit. This was done by commit c31a5c25bb ("ice: Always set prefena
when configuring an Rx queue"). Setting this bit makes sense, since
prefetching descriptors is almost always the preferred behavior.
However, the ice_write_rxq_ctx() function is not the place that actually
defines the queue context. We initialize the Rx Queue context in
ice_setup_rx_ctx(). It is surprising to have the Rx queue context changed
by a function who's responsibility is to program the given context to
hardware.
Following the principle of least surprise, move the setting of the prefetch
enable bit out of ice_write_rxq_ctx() and into the ice_setup_rx_ctx().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-9-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice_rlan_ctx and ice_tlan_ctx structures have some fields which are
intentionally sized larger than necessary relative to the packed sizes the
data must fit into. This was done because the original ice_set_ctx()
function and its helpers did not correctly handle packing when the packed
bits straddled a byte. This is no longer the case with the use of the
<linux/packing.h> implementation.
Save some bytes in these structures by sizing the variables to the number
of bytes the actual bitpacked fields fit into.
There are a couple of gaps left in the structure, which is a result of the
fields being in the order they appear in the packed bit layout, but where
alignment forces some extra gaps. We could fix this, saving ~8 bytes from
each structure. However, these structures are not used heavily, and the
resulting savings is minimal:
$ bloat-o-meter ice-before-reorder.ko ice-after-reorder.ko
add/remove: 0/0 grow/shrink: 1/1 up/down: 26/-70 (-44)
Function old new delta
ice_vsi_cfg_txq 1873 1899 +26
ice_setup_rx_ctx.constprop 1529 1459 -70
Total: Before=1459555, After=1459511, chg -0.00%
Thus, the fields are left in the same order as the packed bit layout,
despite the gaps this causes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-8-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice driver needs to write the Tx and Rx queue context when programming
Tx and Rx queues. This is currently done using some bespoke custom logic
via the ice_set_ctx() and its helper functions, along with bit position
definitions in the ice_tlan_ctx_info and ice_rlan_ctx_info structures.
This logic does work, but is problematic for several reasons:
1) ice_set_ctx requires a helper function for each byte size being packed,
as it uses a separate function to pack u8, u16, u32, and u64 fields.
This requires 4 functions which contain near-duplicate logic with the
types changed out.
2) The logic in the ice_pack_ctx_word, ice_pack_ctx_dword, and
ice_pack_ctx_qword does not handle values which straddle alignment
boundaries very well. This requires that several fields in the
ice_tlan_ctx_info and ice_rlan_ctx_info be a size larger than their bit
size should require.
3) Future support for live migration will require adding unpacking
functions to take the packed hardware context and unpack it into the
ice_rlan_ctx and ice_tlan_ctx structures. Implementing this would
require implementing ice_get_ctx, and its associated helper functions,
which essentially doubles the amount of code required.
The Linux kernel has had a packing library that can handle this logic since
commit 554aae3500 ("lib: Add support for generic packing operations").
The library was recently extended with support for packing or unpacking an
array of fields, with a similar structure as the ice_ctx_ele structure.
Replace the ice-specific ice_set_ctx() logic with the recently added
pack_fields and packed_field_s infrastructure from <linux/packing.h>
For API simplicity, the Tx and Rx queue context are programmed using
separate ice_pack_txq_ctx() and ice_pack_rxq_ctx(). This avoids needing to
export the packed_field_s arrays. The functions can pointers to the
appropriate ice_txq_ctx_buf_t and ice_rxq_ctx_buf_t types, ensuring that
only buffers of the appropriate size are passed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-7-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice Tx and Rx queue context are currently stored as arrays of bytes
with defined size (ICE_RXQ_CTX_SZ and ICE_TXQ_CTX_SZ). The packed queue
context is often passed to other functions as a simple u8 * pointer, which
does not allow tracking the size. This makes the queue context API easy to
misuse, as you can pass an arbitrary u8 array or pointer.
Introduce wrapper typedefs which use a __packed structure that has the
proper fixed size for the Tx and Rx context buffers. This enables the
compiler to track the size of the value and ensures that passing the wrong
buffer size will be detected by the compiler.
The existing APIs do not benefit much from this change, however the
wrapping structures will be used to simplify the arguments of new packing
functions based on the recently introduced pack_fields API.
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-6-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The int_q_state field of the ice_tlan_ctx structure represents the internal
queue state. However, we never actually need to assign this or read this
during normal operation. In fact, trying to unpack it would not be possible
as it is larger than a u64. Remove this field from the ice_tlan_ctx
structure, and remove its packing field from the ice_tlan_ctx_info array.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241210-packing-pack-fields-and-ice-implementation-v10-5-ee56a47479ac@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- rtnetlink: fix double call of rtnl_link_get_net_ifla()
- tcp: populate XPS related fields of timewait sockets
- ethtool: fix access to uninitialized fields in set RXNFC command
- selinux: use sk_to_full_sk() in selinux_ip_output()
Current release - new code bugs:
- net: make napi_hash_lock irq safe
- eth: bnxt_en: support header page pool in queue API
- eth: ice: fix NULL pointer dereference in switchdev
Previous releases - regressions:
- core: fix icmp host relookup triggering ip_rt_bug
- ipv6:
- avoid possible NULL deref in modify_prefix_route()
- release expired exception dst cached in socket
- smc: fix LGR and link use-after-free issue
- hsr: avoid potential out-of-bound access in fill_frame_info()
- can: hi311x: fix potential use-after-free
- eth: ice: fix VLAN pruning in switchdev mode
Previous releases - always broken:
- netfilter:
- ipset: hold module reference while requesting a module
- nft_inner: incorrect percpu area handling under softirq
- can: j1939: fix skb reference counting
- eth: mlxsw: use correct key block on Spectrum-4
- eth: mlx5: fix memory leak in mlx5hws_definer_calc_layout
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEg1AjqC77wbdLX2LbKSR5jcyPE6QFAmdRve4SHHBhYmVuaUBy
ZWRoYXQuY29tAAoJECkkeY3MjxOk/TUQAItDVkTQDiAUUqd0TDH2SSnboxXozcMF
fKVrdWulFAOe7qcajUqjkzvTDjAOw9Xbfh8rEiFBLaXmUzSUT2eqbm2VahvWIR5/
k08v7fTTuCNzEwhnbQlsZ47Nd26LJVPwOvbtE/4V8d50pU/serjWuI/74tUCWAjn
DQOjyyqRjKgKKY+WWCQ6g4tVpD//DB4Sj15GiE3MhlW1f08AAnPJSe2oTaq0RZBG
nXo7abOGn8x3RYilrlp/ZwWYuNpVI4oF+qmp+t/46NV+7ER1JgrC97k0kFyyCYVD
g7vBvFjvA7vDmiuzfsOW2n7IRdcfBtkfi8UJYOIvVgJg7KDF0DXoxj3qD4FagI35
RWRMJw+PoNlFFkPprlp0we/19jPJWOO6rx+AOMEQD78jrH7NoFQ/+eeBf/nppfjy
wX0LD1aQsgPk2ju0I8GbcM/qaJ81EJUiYYVLJHieH0+vvmqts8cMDRLZf5t08EHa
myXcRGB9N8gjguGp5mdR5KmtY82zASlNC0PbDp3nlPYc3e/opCmMRYGjBohO+vqn
n7u250WThPwiBtOwYmSbcK7zpS034/VX0ufnTT2X3MWnFGGNDv6XVmho/OBuCHqJ
m/EiJo/D9qVGAIql/vAxN9a4lQKrcZgaMzCyEPYCf7rtLmzx7sfyHWbf/GZlUAU/
9dUUfWqCbZcL
=nkPk
-----END PGP SIGNATURE-----
Merge tag 'net-6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can and netfilter.
Current release - regressions:
- rtnetlink: fix double call of rtnl_link_get_net_ifla()
- tcp: populate XPS related fields of timewait sockets
- ethtool: fix access to uninitialized fields in set RXNFC command
- selinux: use sk_to_full_sk() in selinux_ip_output()
Current release - new code bugs:
- net: make napi_hash_lock irq safe
- eth:
- bnxt_en: support header page pool in queue API
- ice: fix NULL pointer dereference in switchdev
Previous releases - regressions:
- core: fix icmp host relookup triggering ip_rt_bug
- ipv6:
- avoid possible NULL deref in modify_prefix_route()
- release expired exception dst cached in socket
- smc: fix LGR and link use-after-free issue
- hsr: avoid potential out-of-bound access in fill_frame_info()
- can: hi311x: fix potential use-after-free
- eth: ice: fix VLAN pruning in switchdev mode
Previous releases - always broken:
- netfilter:
- ipset: hold module reference while requesting a module
- nft_inner: incorrect percpu area handling under softirq
- can: j1939: fix skb reference counting
- eth:
- mlxsw: use correct key block on Spectrum-4
- mlx5: fix memory leak in mlx5hws_definer_calc_layout"
* tag 'net-6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
net :mana :Request a V2 response version for MANA_QUERY_GF_STAT
net: avoid potential UAF in default_operstate()
vsock/test: verify socket options after setting them
vsock/test: fix parameter types in SO_VM_SOCKETS_* calls
vsock/test: fix failures due to wrong SO_RCVLOWAT parameter
net/mlx5e: Remove workaround to avoid syndrome for internal port
net/mlx5e: SD, Use correct mdev to build channel param
net/mlx5: E-Switch, Fix switching to switchdev mode in MPV
net/mlx5: E-Switch, Fix switching to switchdev mode with IB device disabled
net/mlx5: HWS: Properly set bwc queue locks lock classes
net/mlx5: HWS: Fix memory leak in mlx5hws_definer_calc_layout
bnxt_en: handle tpa_info in queue API implementation
bnxt_en: refactor bnxt_alloc_rx_rings() to call bnxt_alloc_rx_agg_bmap()
bnxt_en: refactor tpa_info alloc/free into helpers
geneve: do not assume mac header is set in geneve_xmit_skb()
mlxsw: spectrum_acl_flex_keys: Use correct key block on Spectrum-4
ethtool: Fix wrong mod state in case of verbose and no_mask bitset
ipmr: tune the ipmr_can_free_table() checks.
netfilter: nft_set_hash: skip duplicated elements pending gc run
netfilter: ipset: Hold module reference while requesting a module
...
In switchdev mode the uplink VSI should receive all unmatched packets,
including VLANs. Therefore, VLAN pruning should be disabled if uplink is
in switchdev mode. It is already being done in ice_eswitch_setup_env(),
however the addition of ice_up() in commit 44ba608db5 ("ice: do
switchdev slow-path Rx using PF VSI") caused VLAN pruning to be
re-enabled after disabling it.
Add a check to ice_set_vlan_filtering_features() to ensure VLAN
filtering will not be enabled if uplink is in switchdev mode. Note that
ice_is_eswitch_mode_switchdev() is being used instead of
ice_is_switchdev_running(), as the latter would only return true after
the whole switchdev setup completes.
Fixes: 44ba608db5 ("ice: do switchdev slow-path Rx using PF VSI")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Priya Singh <priyax.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To check if PHY Clock Recovery mechanic is available for a device, there
is a need to verify if given PHY is available within the netlist, but the
netlist node type used for the search is wrong, also the search context
shall be specified.
Modify the search function to allow specifying the context in the
search.
Use the PHY node type instead of CLOCK CONTROLLER type, also use proper
search context which for PHY search is PORT, as defined in E810
Datasheet [1] ('3.3.8.2.4 Node Part Number and Node Options (0x0003)' and
'Table 3-105. Program Topology Device NVM Admin Command').
[1] https://cdrdv2.intel.com/v1/dl/getContent/613875?explicitVersion=true
Fixes: 91e43ca009 ("ice: fix linking when CONFIG_PTP_1588_CLOCK=n")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-11-05 (ice, ixgbe, igc. igb, igbvf, e1000)
For ice:
Mateusz refactors and adds additional SerDes configuration values to be
output.
Przemek refactors processing of DDP and adds support for a flag field in
the DDP's signature segment header.
Joe Damato adds support for persistent NAPI config.
Brett adjusts setting of Tx promiscuous based on unicast/multicast
setting.
Jake moves setting of pf->supported_rxdids to occur directly after DDP
load and changes a small struct to use stack memory.
Frederic Weisbecker adds WQ_UNBOUND flag to the workqueue.
For ixgbe:
Diomidis Spinellis removes a circular dependency.
For igc:
Vitaly removes an unneeded autoneg parameter.
For igb:
Johnny Park fixes a couple of typos.
For igbvf:
Wander Lairson Costa removes an unused spinlock.
For e1000:
Joe Damato adds RTNL lock to some calls where it is expected to be held.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000: Hold RTNL when e1000_down can be called
igbvf: remove unused spinlock
igb: Fix 2 typos in comments in igb_main.c
igc: remove autoneg parameter from igc_mac_info
ixgbe: Break include dependency cycle
ice: Unbind the workqueue
ice: use stack variable for virtchnl_supported_rxdids
ice: initialize pf->supported_rxdids immediately after loading DDP
ice: only allow Tx promiscuous for multicast
ice: Add support for persistent NAPI config
ice: support optional flags in signature segment header
ice: refactor "last" segment of DDP pkg
ice: extend dump serdes equalizer values feature
ice: rework of dump serdes equalizer values feature
====================
Link: https://patch.msgid.link/20241113185431.1289708-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a similar fashion to ndo_fdb_add, which was covered in the previous
patch, add the bool *notified argument to ndo_fdb_del. Callees that send a
notification on their own set the flag to true.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/06b1acf4953ef0a5ed153ef1f32d7292044f2be6.1731589511.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently when FDB entries are added to or deleted from a VXLAN netdevice,
the VXLAN driver emits one notification, including the VXLAN-specific
attributes. The core however always sends a notification as well, a generic
one. Thus two notifications are unnecessarily sent for these operations. A
similar situation comes up with bridge driver, which also emits
notifications on its own:
# ip link add name vx type vxlan id 1000 dstport 4789
# bridge monitor fdb &
[1] 1981693
# bridge fdb add de:ad:be:ef:13:37 dev vx self dst 192.0.2.1
de:ad:be:ef:13:37 dev vx dst 192.0.2.1 self permanent
de:ad:be:ef:13:37 dev vx self permanent
In order to prevent this duplicity, add a paremeter to ndo_fdb_add,
bool *notified. The flag is primed to false, and if the callee sends a
notification on its own, it sets it to true, thus informing the core that
it should not generate another notification.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/cbf6ae8195e85cbf922f8058ce4eba770f3b71ed.1731589511.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice workqueue doesn't seem to rely on any CPU locality and should
therefore be able to run on any CPU. In practice this is already
happening through the unbound ice_service_timer that may fire anywhere
and queue the workqueue accordingly to any CPU.
Make this official so that the ice workqueue is only ever queued to
housekeeping CPUs on nohz_full.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_vc_query_rxdid() function allocates memory to store the
virtchnl_supported_rxdids structure used to communicate the bitmap of
supported RXDIDs to a VF.
This structure is only 8 bytes in size. The function must hold the
allocated length on the stack as well as the pointer to the structure which
itself is 8 bytes. Allocating this storage on the heap adds unnecessary
overhead including a potential error path that must be handled in case
kzalloc fails. Because this structure is so small, we're not saving stack
space. Additionally, because we must ensure that we free the allocated
memory, the return value from ice_vc_send_msg_to_vf() must also be saved in
the stack ret variable. Depending on compiler optimization, this means
allocating the 8-byte structure is requiring up to 16-bytes of stack
memory!
Simplify this function to keep the rxdid variable on the stack, saving
memory and removing a potential failure exit path from this function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The pf->supported_rxdids field is used to populate the list of valid RXDIDs
that a VF may use when negotiating VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC.
The set of supported RXDIDs is dependent on the DDP, and can be read from
the GLXFLXP_RXDID_FLAGS register. The PF needs to send this list to the
VF upon receiving the VIRTCHNL_OP_GET_SUPPORTED_RXDIDs. It also needs to
use this list to validate the requested descriptor ID from the VF when
programming the Rx queues.
A future update to support VF live migration will also want to validate
that the target VF can support the same descriptor ID when migrating.
Currently, pf->supported_rxdids is initialized inside the
ice_vc_query_rxdid() function. This means that it is only ever initialized
if at least one VF actually tries to negotiate
VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC. It is also unnecessarily re-initialized
every time the VF loads and requests the descriptor list. This worked
before because the PF only checks pf->suppported_rxdids when programming
the Rx queue if the VF actually negotiates the
VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC feature.
This will be problematic for VF live migration. We need the list of
supported Rx descriptor IDs when migrating. It is possible that no VF on
the target PF has ever actually issued a VIRTCHNL_OP_GET_SUPPORTED_RXDIDs.
Refactor the driver to initialize pf->supported_rxdids during driver
initialization after the DDP is loaded. This is simpler, avoids unnecessary
duplicate work, and avoids issues with the live migration process.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when any VF is trusted and true promiscuous mode is enabled on
the PF, the VF will receive all unicast traffic directed to the device's
internal switch. This includes traffic external to the NIC and also from
other VSI (i.e. VFs). This does not match the expected behavior as
unicast traffic should only be visible from external sources in this
case. Disable the Tx promiscuous mode bits for unicast promiscuous mode.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
An optional flag field has been added to the signature segment header.
The field contains two flags, a "valid" bit, and a "last segment" bit
that indicates whether the segment is the last segment that will be
sent to firmware.
If the flag field's valid bit is NOT set, then as was done before,
assume that this is the last segment being downloaded.
However, if the flag field's valid bit IS set, then use the last segment
flag to determine if this segment is the last segment to download.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add ice_ddp_send_hunk() that buffers "sent FW hunk" calls to AQ in order
to mark the "last" one in more elegant way. Next commit will add even
more complicated "sent FW" flow, so it's better to untangle a bit before.
Note that metadata buffers were not skipped for NOT-@indicate_last
segments, this is fixed now.
Minor:
+ use ice_is_buffer_metadata() instead of open coding it in
ice_dwnld_cfg_bufs();
+ ice_dwnld_cfg_bufs_no_lock() + dependencies were moved up a bit to have
better git-diff, as this function was rewritten (in terms of git-blame)
CC: Paul Greenwalt <paul.greenwalt@intel.com>
CC: Dan Nowlin <dan.nowlin@intel.com>
CC: Ahmed Zaki <ahmed.zaki@intel.com>
CC: Simon Horman <horms@kernel.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Extend the work done in commit 70838938e8 ("ice: Implement driver
functionality to dump serdes equalizer values") by adding the new set of
Rx registers that can be read using command:
$ ethtool -d interface_name
Rx equalization parameters are E810 PHY registers used by end user to
gather information about configuration and status to debug link and
connection issues in the field.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor function ice_get_tx_rx_equa() to iterate over new table of
params instead of multiple calls to ice_aq_get_phy_equalization().
Subsequent commit will extend that function by add more serdes equalizer
values to dump.
Shorten the fields of struct ice_serdes_equalization_to_ethtool for
readability purposes.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix Flow Director not allowing to re-map traffic to 0th queue when action
is configured to drop (and vice versa).
The current implementation of ethtool callback in the ice driver forbids
change Flow Director action from 0 to -1 and from -1 to 0 with an error,
e.g:
# ethtool -U eth2 flow-type tcp4 src-ip 1.1.1.1 loc 1 action 0
# ethtool -U eth2 flow-type tcp4 src-ip 1.1.1.1 loc 1 action -1
rmgr: Cannot insert RX class rule: Invalid argument
We set the value of `u16 q_index = 0` at the beginning of the function
ice_set_fdir_input_set(). In case of "drop traffic" action (which is
equal to -1 in ethtool) we store the 0 value. Later, when want to change
traffic rule to redirect to queue with index 0 it returns an error
caused by duplicate found.
Fix this behaviour by change of the type of field `q_index` from u16 to s16
in `struct ice_fdir_fltr`. This allows to store -1 in the field in case
of "drop traffic" action. What is more, change the variable type in the
function ice_set_fdir_input_set() and assign at the beginning the new
`#define ICE_FDIR_NO_QUEUE_IDX` which is -1. Later, if the action is set
to another value (point specific queue index) the variable value is
overwritten in the function.
Fixes: cac2a27cd9 ("ice: Support IPv4 Flow Director filters")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unloading the ice driver while switchdev port representors are added to
a bridge can lead to kernel panic. Reproducer:
modprobe ice
devlink dev eswitch set $PF1_PCI mode switchdev
ip link add $BR type bridge
ip link set $BR up
echo 2 > /sys/class/net/$PF1/device/sriov_numvfs
sleep 2
ip link set $PF1 master $BR
ip link set $VF1_PR master $BR
ip link set $VF2_PR master $BR
ip link set $PF1 up
ip link set $VF1_PR up
ip link set $VF2_PR up
ip link set $VF1 up
rmmod irdma ice
When unloading the driver, ice_eswitch_detach() is eventually called as
part of VF freeing. First, it removes a port representor from xarray,
then unregister_netdev() is called (via repr->ops.rem()), finally
representor is deallocated. The problem comes from the bridge doing its
own deinit at the same time. unregister_netdev() triggers a notifier
chain, resulting in ice_eswitch_br_port_deinit() being called. It should
set repr->br_port = NULL, but this does not happen since repr has
already been removed from xarray and is not found. Regardless, it
finishes up deallocating br_port. At this point, repr is still not freed
and an fdb event can happen, in which ice_eswitch_br_fdb_event_work()
takes repr->br_port and tries to use it, which causes a panic (use after
free).
Note that this only happens with 2 or more port representors added to
the bridge, since with only one representor port, the bridge deinit is
slightly different (ice_eswitch_br_port_deinit() is called via
ice_eswitch_br_ports_flush(), not ice_eswitch_br_port_unlink()).
Trace:
Oops: general protection fault, probably for non-canonical address 0xf129010fd1a93284: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0x8948287e8d499420-0x8948287e8d499427]
(...)
Workqueue: ice_bridge_wq ice_eswitch_br_fdb_event_work [ice]
RIP: 0010:__rht_bucket_nested+0xb4/0x180
(...)
Call Trace:
(...)
ice_eswitch_br_fdb_find+0x3fa/0x550 [ice]
? __pfx_ice_eswitch_br_fdb_find+0x10/0x10 [ice]
ice_eswitch_br_fdb_event_work+0x2de/0x1e60 [ice]
? __schedule+0xf60/0x5210
? mutex_lock+0x91/0xe0
? __pfx_ice_eswitch_br_fdb_event_work+0x10/0x10 [ice]
? ice_eswitch_br_update_work+0x1f4/0x310 [ice]
(...)
A workaround is available: brctl setageing $BR 0, which stops the bridge
from adding fdb entries altogether.
Change the order of operations in ice_eswitch_detach(): move the call to
unregister_netdev() before removing repr from xarray. This way
repr->br_port will be correctly set to NULL in
ice_eswitch_br_port_deinit(), preventing a panic.
Fixes: fff292b47a ("ice: add VF representors one by one")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
net_dim() is currently passed a struct dim_sample argument by value.
struct dim_sample is 24 bytes. Since this is greater 16 bytes, x86-64
passes it on the stack. All callers have already initialized dim_sample
on the stack, so passing it by value requires pushing a duplicated copy
to the stack. Either witing to the stack and immediately reading it, or
perhaps dereferencing addresses relative to the stack pointer in a chain
of push instructions, seems to perform quite poorly.
In a heavy TCP workload, mlx5e_handle_rx_dim() consumes 3% of CPU time,
94% of which is attributed to the first push instruction to copy
dim_sample on the stack for the call to net_dim():
// Call ktime_get()
0.26 |4ead2: call 4ead7 <mlx5e_handle_rx_dim+0x47>
// Pass the address of struct dim in %rdi
|4ead7: lea 0x3d0(%rbx),%rdi
// Set dim_sample.pkt_ctr
|4eade: mov %r13d,0x8(%rsp)
// Set dim_sample.byte_ctr
|4eae3: mov %r12d,0xc(%rsp)
// Set dim_sample.event_ctr
0.15 |4eae8: mov %bp,0x10(%rsp)
// Duplicate dim_sample on the stack
94.16 |4eaed: push 0x10(%rsp)
2.79 |4eaf1: push 0x10(%rsp)
0.07 |4eaf5: push %rax
// Call net_dim()
0.21 |4eaf6: call 4eafb <mlx5e_handle_rx_dim+0x6b>
To allow the caller to reuse the struct dim_sample already on the stack,
pass the struct dim_sample by reference to net_dim().
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Arthur Kiyanovski <akiyano@amazon.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Link: https://patch.msgid.link/20241031002326.3426181-2-csander@purestorage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The E810 Lan On Motherboard (LOM) design is vendor specific. Intel
provides the reference design, but it is up to vendor on the final
product design. For some cases, like Linux DPLL support, the static
values defined in the driver does not reflect the actual LOM design.
Current implementation of dpll pins is causing the crash on probe
of the ice driver for such DPLL enabled E810 LOM designs:
WARNING: (...) at drivers/dpll/dpll_core.c:495 dpll_pin_get+0x2c4/0x330
...
Call Trace:
<TASK>
? __warn+0x83/0x130
? dpll_pin_get+0x2c4/0x330
? report_bug+0x1b7/0x1d0
? handle_bug+0x42/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? dpll_pin_get+0x117/0x330
? dpll_pin_get+0x2c4/0x330
? dpll_pin_get+0x117/0x330
ice_dpll_get_pins.isra.0+0x52/0xe0 [ice]
...
The number of dpll pins enabled by LOM vendor is greater than expected
and defined in the driver for Intel designed NICs, which causes the crash.
Prevent the crash and allow generic pin initialization within Linux DPLL
subsystem for DPLL enabled E810 LOM designs.
Newly designed solution for described issue will be based on "per HW
design" pin initialization. It requires pin information dynamically
acquired from the firmware and is already in progress, planned for
next-tree only.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is no support for SF in legacy mode. Reflect it in the code.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Fixes: eda69d654c ("ice: add basic devlink subfunctions support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to configure VF queue rate limit and quanta size.
For quanta size configuration, the quanta profiles are divided evenly
by PF numbers. For each port, the first quanta profile is reserved for
default. When VF is asked to set queue quanta size, PF will search for
an available profile, change the fields and assigned this profile to the
queue.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Wenjun Wu <wenjun1.wu@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/fddefc2c1ec3ab32b241ce444af401da19e834dd.1728460186.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit fff292b47a ("ice: add VF representors one by one")
ice_eswitch_configure() is not used anymore.
Commit 1b8f15b64a ("ice: refactor filter functions") removed
ice_vsi_cfg_mac_fltr() but leave declaration.
Commit a24b4c6e9a ("ice: xsk: Do not convert to buff to frame for
XDP_TX") leave ice_xmit_xdp_buff() declaration.
Commit 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C
products") declared ice_phy_cfg_{rx,tx}_offset_eth56g(),
commit a1ffafb0b4 ("ice: Support configuring the device to Double
VLAN Mode") declared ice_pkg_buf_get_free_space(), and
commit 8a3a565ff2 ("ice: add admin commands to access cgu
configuration") declared ice_is_pca9575_present(), but all these never
be implemented.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add jump targets so that a bit of exception handling can be better reused
at the end of two function implementations.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have for some time the assign_bit() API to replace open coded
if (foo)
set_bit(n, bar);
else
clear_bit(n, bar);
Use this API to clean the code. No functional change intended.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The max_frame and rx_buf_len fields of the VSI set the maximum frame size
for packets on the wire, and configure the size of the Rx buffer. In the
hardware, these are per-queue configuration. Most VSI types use a simple
method to determine the size of the buffers for all queues.
However, VFs may potentially configure different values for each queue.
While the Linux iAVF driver does not do this, it is allowed by the virtchnl
interface.
The current virtchnl code simply sets the per-VSI fields inbetween calls to
ice_vsi_cfg_single_rxq(). This technically works, as these fields are only
ever used when programming the Rx ring, and otherwise not checked again.
However, it is confusing to maintain.
The Rx ring also already has an rx_buf_len field in order to access the
buffer length in the hotpath. It also has extra unused bytes in the ring
structure which we can make use of to store the maximum frame size.
Drop the VSI max_frame and rx_buf_len fields. Add max_frame to the Rx ring,
and slightly re-order rx_buf_len to better fit into the gaps in the
structure layout.
Change the ice_vsi_cfg_frame_size function so that it writes to the ring
fields. Call this function once per ring in ice_vsi_cfg_rxqs(). This is
done over calling it inside the ice_vsi_cfg_rxq(), because
ice_vsi_cfg_rxq() is called in the virtchnl flow where the max_frame and
rx_buf_len have already been configured.
Change the accesses for rx_buf_len and max_frame to all point to the ring
structure. This has the added benefit that ice_vsi_cfg_rxq() no longer has
the surprise side effect of updating ring->rx_buf_len based on the VSI
field.
Update the virtchnl ice_vc_cfg_qs_msg() function to set the ring values
directly, and drop references to the removed VSI fields.
This now makes the VF logic clear, as the ring fields are obviously
per-queue. This reduces the required cognitive load when reasoning about
this logic.
Note that removing the VSI fields does leave a 4 byte gap, but the ice_vsi
structure has many gaps, and its layout is not as critical in the hot path.
The structure may benefit from a more thorough repacking, but no attempt
was made in this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_vc_cfg_qs_msg() function is used to configure VF queues in response
to a VIRTCHNL_OP_CONFIG_VSI_QUEUES command.
The virtchnl command contains an array of queue pair data for configuring
Tx and Rx queues. This data includes a queue ID. When configuring the
queues, the driver generally uses this queue ID to determine which Tx and
Rx ring to program. However, a handful of places use the index into the
queue pair data from the VF. While most VF implementations appear to send
this data in order, it is not mandated by the virtchnl and it is not
verified that the queue pair data comes in order.
Fix the driver to consistently use the q_idx field instead of the 'i'
iterator value when accessing the rings. For the Rx case, introduce a local
ring variable to keep lines short.
Fixes: 7ad15440ac ("ice: Refactor VIRTCHNL_OP_CONFIG_VSI_QUEUES handling")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
E830 adds hardware support to prevent the VF from overflowing the PF
mailbox with VIRTCHNL messages. E830 will use the hardware feature
(ICE_F_MBX_LIMIT) instead of the software solution ice_is_malicious_vf().
To prevent a VF from overflowing the PF, the PF sets the number of
messages per VF that can be in the PF's mailbox queue
(ICE_MBX_OVERFLOW_WATERMARK). When the PF processes a message from a VF,
the PF decrements the per VF message count using the E830_MBX_VF_DEC_TRIG
register.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Increasing MSI-X value on a VF leads to invalid memory operations. This
is caused by not reallocating some arrays.
Reproducer:
modprobe ice
echo 0 > /sys/bus/pci/devices/$PF_PCI/sriov_drivers_autoprobe
echo 1 > /sys/bus/pci/devices/$PF_PCI/sriov_numvfs
echo 17 > /sys/bus/pci/devices/$VF0_PCI/sriov_vf_msix_count
Default MSI-X is 16, so 17 and above triggers this issue.
KASAN reports:
BUG: KASAN: slab-out-of-bounds in ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
Read of size 8 at addr ffff8888b937d180 by task bash/28433
(...)
Call Trace:
(...)
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
kasan_report+0xed/0x120
? ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_alloc_ring_stats+0x38d/0x4b0 [ice]
ice_vsi_cfg_def+0x3360/0x4770 [ice]
? mutex_unlock+0x83/0xd0
? __pfx_ice_vsi_cfg_def+0x10/0x10 [ice]
? __pfx_ice_remove_vsi_lkup_fltr+0x10/0x10 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vf_reconfig_vsi+0x114/0x210 [ice]
ice_sriov_set_msix_vec_count+0x3d0/0x960 [ice]
sriov_vf_msix_count_store+0x21c/0x300
(...)
Allocated by task 28201:
(...)
ice_vsi_cfg_def+0x1c8e/0x4770 [ice]
ice_vsi_cfg+0x7f/0x3b0 [ice]
ice_vsi_setup+0x179/0xa30 [ice]
ice_sriov_configure+0xcaa/0x1520 [ice]
sriov_numvfs_store+0x212/0x390
(...)
To fix it, use ice_vsi_rebuild() instead of ice_vf_reconfig_vsi(). This
causes the required arrays to be reallocated taking the new queue count
into account (ice_vsi_realloc_stat_arrays()). Set req_txq and req_rxq
before ice_vsi_rebuild(), so that realloc uses the newly set queue
count.
Additionally, ice_vsi_rebuild() does not remove VSI filters
(ice_fltr_remove_all()), so ice_vf_init_host_cfg() is no longer
necessary.
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 2a2cb4c6c1 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Triggering the reset while in switchdev mode causes
errors[1]. Rules are already removed by this time
because switch content is flushed in case of the reset.
This means that rules were deleted from HW but SW
still thinks they exist so when we get
SWITCHDEV_FDB_DEL_TO_DEVICE notification we try to
delete not existing rule.
We can avoid these errors by clearing the rules
early in the reset flow before they are removed from HW.
Switchdev API will get notified that the rule was removed
so we won't get SWITCHDEV_FDB_DEL_TO_DEVICE notification.
Remove unnecessary ice_clear_sw_switch_recipes.
[1]
ice 0000:01:00.0: Failed to delete FDB forward rule, err: -2
ice 0000:01:00.0: Failed to delete FDB guard rule, err: -2
Fixes: 7c945a1a8e ("ice: Switchdev FDB events support")
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
netif_is_ice() works by checking the pointer to netdev ops. However, it
only checks for the default ice_netdev_ops, not ice_netdev_safe_mode_ops,
so in Safe Mode it always returns false, which is unintuitive. While it
doesn't look like netif_is_ice() is currently being called anywhere in Safe
Mode, this could change and potentially lead to unexpected behaviour.
Fixes: df006dd4b1 ("ice: Add initial support framework for LAG")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If DDP package is missing or corrupted, the driver should enter Safe Mode.
Instead, an error is returned and probe fails.
To fix this, don't exit init if ice_init_ddp_config() returns an error.
Repro:
* Remove or rename DDP package (/lib/firmware/intel/ice/ddp/ice.pkg)
* Load ice
Fixes: cc5776fe18 ("ice: Enable switching default Tx scheduler topology")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-10-01 (ice)
This series contains updates to ice driver only.
Karol cleans up current PTP GPIO pin handling, fixes minor bugs,
refactors implementation for all products, introduces SDP (Software
Definable Pins) for E825C and implements reading SDP section from NVM
for E810 products.
Sergey replaces multiple aux buses and devices used in the PTP support
code with struct ice_adapter holding the necessary shared data.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Drop auxbus use for PTP to finalize ice_adapter move
ice: Use ice_adapter for PTP shared data instead of auxdev
ice: Initial support for E825C hardware in ice_adapter
ice: Add ice_get_ctrl_ptp() wrapper to simplify the code
ice: Introduce ice_get_phy_model() wrapper
ice: Enable 1PPS out from CGU for E825C products
ice: Read SDP section from NVM for pin definitions
ice: Disable shared pin on E810 on setfunc
ice: Cache perout/extts requests and check flags
ice: Align E810T GPIO to other products
ice: Add SDPs support for E825C
ice: Implement ice_ptp_pin_desc
====================
Link: https://patch.msgid.link/20241001201702.3252954-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-09-30 (ice, idpf)
This series contains updates to ice and idpf drivers:
For ice:
Michal corrects setting of dst VSI on LAN filters and adds clearing of
port VLAN configuration during reset.
Gui-Dong Han corrects failures to decrement refcount in some error
paths.
Przemek resolves a memory leak in ice_init_tx_topology().
Arkadiusz prevents setting of DPLL_PIN_STATE_SELECTABLE to an improper
value.
Dave stops clearing of VLAN tracking bit to allow for VLANs to be properly
restored after reset.
For idpf:
Ahmed sets uninitialized dyn_ctl_intrvl_s value.
Josh corrects use and reporting of mailbox size.
Larysa corrects order of function calls during de-initialization.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: deinit virtchnl transaction manager after vport and vectors
idpf: use actual mbx receive payload length
idpf: fix VF dynamic interrupt ctl register initialization
ice: fix VLAN replay after reset
ice: disallow DPLL_PIN_STATE_SELECTABLE for dpll output pins
ice: fix memleak in ice_init_tx_topology()
ice: clear port vlan config during reset
ice: Fix improper handling of refcount in ice_sriov_set_msix_vec_count()
ice: Fix improper handling of refcount in ice_dpll_init_rclk_pins()
ice: set correct dst VSI in only LAN filters
====================
Link: https://patch.msgid.link/20240930223601.3137464-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Drop unused auxbus/auxdev support from the PTP code due to
move to the ice_adapter.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use struct ice_adapter to hold shared PTP data and control PTP
related actions instead of auxbus. This allows significant code
simplification and faster access to the container fields used in
the PTP support code.
Move the PTP port list to the ice_adapter container to simplify
the code and avoid race conditions which could occur due to the
synchronous nature of the initialization/access and
certain memory saving can be achieved by moving PTP data into
the ice_adapter itself.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Address E825C devices by PCI ID since dual IP core configurations
need 1 ice_adapter for both devices.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add ice_get_ctrl_ptp() wrapper to simplify the PTP support code
in the functions that do not use ctrl_pf directly.
Add the control PF pointer to struct ice_adapter
Rearrange fields in struct ice_adapter
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement configuring 1PPS signal output from CGU. Use maximal amplitude
because Linux PTP pin API does not have any way for user to set signal
level.
This change is necessary for E825C products to properly output any
signal from 1PPS pin.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
PTP pins assignment and their related SDPs (Software Definable Pins) are
currently hardcoded.
Fix that by reading NVM section instead on products supporting this,
which are E810 products.
If SDP section is not defined in NVM, the driver continues to use the
hardcoded table.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When setting a new supported function for a pin on E810, disable other
enabled pin that shares the same GPIO.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cache original PTP GPIO requests instead of saving each parameter in
internal structures for periodic output or external timestamp request.
Factor out all periodic output register writes from ice_ptp_cfg_clkout
to a separate function to improve readability.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of having separate PTP GPIO implementation for E810T, use
existing one from all other products.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support of PTP SDPs (Software Definable Pins) for E825C products.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new internal structure describing PTP pins.
Use the new structure for all non-E810T products.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a bug currently when there are more than one VLAN defined
and any reset that affects the PF is initiated, after the reset rebuild
no traffic will pass on any VLAN but the last one created.
This is caused by the iteration though the VLANs during replay each
clearing the vsi_map bitmap of the VSI that is being replayed. The
problem is that during rhe replay, the pointer to the vsi_map bitmap
is used by each successive vlan to determine if it should be replayed
on this VSI.
The logic was that the replay of the VLAN would replace the bit in the map
before the next VLAN would iterate through. But, since the replay copies
the old bitmap pointer to filt_replay_rules and creates a new one for the
recreated VLANS, it does not do this, and leaves the old bitmap broken
to be used to replay the remaining VLANs.
Since the old bitmap will be cleaned up in post replay cleanup, there is
no need to alter it and break following VLAN replay, so don't clear the
bit.
Fixes: 334cb0626d ("ice: Implement VSI replay framework")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the user may request DPLL_PIN_STATE_SELECTABLE for an output
pin, and this would actually set the DISCONNECTED state instead.
It doesn't make any sense. SELECTABLE is valid only in case of input pins
(on AUTOMATIC type dpll), where dpll itself would select best valid input.
For the output pin only CONNECTED/DISCONNECTED are expected.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix leak of the FW blob (DDP pkg).
Make ice_cfg_tx_topo() const-correct, so ice_init_tx_topology() can avoid
copying whole FW blob. Copy just the topology section, and only when
needed. Reuse the buffer allocated for the read of the current topology.
This was found by kmemleak, with the following trace for each PF:
[<ffffffff8761044d>] kmemdup_noprof+0x1d/0x50
[<ffffffffc0a0a480>] ice_init_ddp_config+0x100/0x220 [ice]
[<ffffffffc0a0da7f>] ice_init_dev+0x6f/0x200 [ice]
[<ffffffffc0a0dc49>] ice_init+0x29/0x560 [ice]
[<ffffffffc0a10c1d>] ice_probe+0x21d/0x310 [ice]
Constify ice_cfg_tx_topo() @buf parameter.
This cascades further down to few more functions.
Fixes: cc5776fe18 ("ice: Enable switching default Tx scheduler topology")
CC: Larysa Zaremba <larysa.zaremba@intel.com>
CC: Jacob Keller <jacob.e.keller@intel.com>
CC: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
CC: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since commit 2a2cb4c6c1 ("ice: replace ice_vf_recreate_vsi() with
ice_vf_reconfig_vsi()") VF VSI is only reconfigured instead of
recreated. The context configuration from previous setting is still the
same. If any of the config needs to be cleared it needs to be cleared
explicitly.
Previously there was assumption that port vlan will be cleared
automatically. Now, when VSI is only reconfigured we have to do it in the
code.
Not clearing port vlan configuration leads to situation when the driver
VSI config is different than the VSI config in HW. Traffic can't be
passed after setting and clearing port vlan, because of invalid VSI
config in HW.
Example reproduction:
> ip a a dev $(VF) $(VF_IP_ADDRESS)
> ip l s dev $(VF) up
> ping $(VF_IP_ADDRESS)
ping is working fine here
> ip link set eth5 vf 0 vlan 100
> ip link set eth5 vf 0 vlan 0
> ping $(VF_IP_ADDRESS)
ping isn't working
Fixes: 2a2cb4c6c1 ("ice: replace ice_vf_recreate_vsi() with ice_vf_reconfig_vsi()")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Piotr Tyda <piotr.tyda@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch addresses an issue with improper reference count handling in the
ice_sriov_set_msix_vec_count() function.
First, the function calls ice_get_vf_by_id(), which increments the
reference count of the vf pointer. If the subsequent call to
ice_get_vf_vsi() fails, the function currently returns an error without
decrementing the reference count of the vf pointer, leading to a reference
count leak. The correct behavior, as implemented in this patch, is to
decrement the reference count using ice_put_vf(vf) before returning an
error when vsi is NULL.
Second, the function calls ice_sriov_get_irqs(), which sets
vf->first_vector_idx. If this call returns a negative value, indicating an
error, the function returns an error without decrementing the reference
count of the vf pointer, resulting in another reference count leak. The
patch addresses this by adding a call to ice_put_vf(vf) before returning
an error when vf->first_vector_idx < 0.
This bug was identified by an experimental static analysis tool developed
by our team. The tool specializes in analyzing reference count operations
and identifying potential mismanagement of reference counts. In this case,
the tool flagged the missing decrement operation as a potential issue,
leading to this patch.
Fixes: 4035c72dc1 ("ice: reconfig host after changing MSI-X on VF")
Fixes: 4d38cb44bd ("ice: manage VFs MSI-X using resource tracking")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@outlook.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch addresses a reference count handling issue in the
ice_dpll_init_rclk_pins() function. The function calls ice_dpll_get_pins(),
which increments the reference count of the relevant resources. However,
if the condition WARN_ON((!vsi || !vsi->netdev)) is met, the function
currently returns an error without properly releasing the resources
acquired by ice_dpll_get_pins(), leading to a reference count leak.
To resolve this, the check has been moved to the top of the function. This
ensures that the function verifies the state before any resources are
acquired, avoiding the need for additional resource management in the
error path.
This bug was identified by an experimental static analysis tool developed
by our team. The tool specializes in analyzing reference count operations
and detecting potential issues where resources are not properly managed.
In this case, the tool flagged the missing release operation as a
potential problem, which led to the development of this patch.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@outlook.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The filters set that will reproduce the problem:
$ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \
skip_sw dst_mac ff:ff:ff:ff:ff:ff action mirred egress \
redirect dev $PF0
$ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \
skip_sw dst_mac ff:ff:ff:ff:ff:ff src_mac 52:54:00:00:00:10 \
action mirred egress mirror dev $VF1_PR
Expected behaviour is to set all broadcast from VF0 to the LAN. If the
src_mac match the value from filters, send packet to LAN and to VF1.
In this case both LAN_EN and LB_EN flags in switch is set in case of
packet matching both filters. As dst VSI for the only LAN enable bit is
PF VSI, the packet is being seen on PF. To fix this change dst VSI to
the source VSI. It will block receiving any packet even when LB_EN is
set by switch, because local loopback is clear on VF VSI during normal
operation.
Side note: if the second filters action is redirect instead of mirror
LAN_EN is clear, because switch is AND-ing LAN_EN from each matched
filters and OR-ing LB_EN.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Fixes: 73b483b790 ("ice: Manage act flags for switchdev offloads")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_allocate_sf() function returns error pointers on error. It
doesn't return NULL. Update the check to match.
Fixes: 177ef7f1e2 ("ice: base subfunction aux driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/6951d217-ac06-4482-a35d-15d757fd90a3@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice_repr_create() function returns error pointers. It never returns
NULL. Fix the callers to check for IS_ERR().
Fixes: 977514fb0f ("ice: create port representor for SF")
Fixes: 415db8399d ("ice: make representor code generic")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/7f7aeb91-8771-47b8-9275-9d9f64f947dd@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb2 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The description of function ice_find_vsi_list_entry says:
Search VSI list map with VSI count 1
However, since the blamed commit (see Fixes below), the function no
longer checks vsi_count. This causes a problem in ice_add_vlan_internal,
where the decision to share VSI lists between filter rules relies on the
vsi_count of the found existing VSI list being 1.
The reproducing steps:
1. Have a PF and two VFs.
There will be a filter rule for VLAN 0, referring to a VSI list
containing VSIs: 0 (PF), 2 (VF#0), 3 (VF#1).
2. Add VLAN 1234 to VF#0.
ice will make the wrong decision to share the VSI list with the new
rule. The wrong behavior may not be immediately apparent, but it can
be observed with debug prints.
3. Add VLAN 1234 to VF#1.
ice will unshare the VSI list for the VLAN 1234 rule. Due to the
earlier bad decision, the newly created VSI list will contain
VSIs 0 (PF) and 3 (VF#1), instead of expected 2 (VF#0) and 3 (VF#1).
4. Try pinging a network peer over the VLAN interface on VF#0.
This fails.
Reproducer script at:
https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/test-vlan-vsi-list-confusion.sh
Commented debug trace:
https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/ice-vlan-vsi-lists-debug.txt
Patch adding the debug prints:
f8a8814623
(Unsafe, by the way. Lacks rule_lock when dumping in ice_remove_vlan.)
Michal Swiatkowski added to the explanation that the bug is caused by
reusing a VSI list created for VLAN 0. All created VFs' VSIs are added
to VLAN 0 filter. When a non-zero VLAN is created on a VF which is already
in VLAN 0 (normal case), the VSI list from VLAN 0 is reused.
It leads to a problem because all VFs (VSIs to be specific) that are
subscribed to VLAN 0 will now receive a new VLAN tag traffic. This is
one bug, another is the bug described above. Removing filters from
one VF will remove VLAN filter from the previous VF. It happens a VF is
reset. Example:
- creation of 3 VFs
- we have VSI list (used for VLAN 0) [0 (pf), 2 (vf1), 3 (vf2), 4 (vf3)]
- we are adding VLAN 100 on VF1, we are reusing the previous list
because 2 is there
- VLAN traffic works fine, but VLAN 100 tagged traffic can be received
on all VSIs from the list (for example broadcast or unicast)
- trust is turning on VF2, VF2 is resetting, all filters from VF2 are
removed; the VLAN 100 filter is also removed because 3 is on the list
- VLAN traffic to VF1 isn't working anymore, there is a need to recreate
VLAN interface to readd VLAN filter
One thing I'm not certain about is the implications for the LAG feature,
which is another caller of ice_find_vsi_list_entry. I don't have a
LAG-capable card at hand to test.
Fixes: 23ccae5ce1 ("ice: changes to the interface with the HW and FW for SRIOV_VF+LAG")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Dave Ertman <David.m.ertman@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Our driver uses devres to manage resources, in particular we call
pcim_enable_device(), what also means we express the intent to get
automatic pci_disable_device() call at driver removal. Manual calls to
pci_disable_device() misuse the API.
Recent commit (see "Fixes" tag) has changed the removal action from
conditional (silent ignore of double call to pci_disable_device()) to
unconditional, but able to catch unwanted redundant calls; see cited
"Fixes" commit for details.
Since that, unloading the driver yields following warn+splat:
[70633.628490] ice 0000:af:00.7: disabling already-disabled device
[70633.628512] WARNING: CPU: 52 PID: 33890 at drivers/pci/pci.c:2250 pci_disable_device+0xf4/0x100
...
[70633.628744] ? pci_disable_device+0xf4/0x100
[70633.628752] release_nodes+0x4a/0x70
[70633.628759] devres_release_all+0x8b/0xc0
[70633.628768] device_unbind_cleanup+0xe/0x70
[70633.628774] device_release_driver_internal+0x208/0x250
[70633.628781] driver_detach+0x47/0x90
[70633.628786] bus_remove_driver+0x80/0x100
[70633.628791] pci_unregister_driver+0x2a/0xb0
[70633.628799] ice_module_exit+0x11/0x3a [ice]
Note that this is the only Intel ethernet driver that needs such fix.
Fixes: f748a07a0b ("PCI: Remove legacy pcim_release()")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When adding a switch filter (such as a MAC or VLAN filter), it is expected
that the driver will detect the case where the filter already exists, and
return -EEXIST. This is used by calling code such as ice_vc_add_mac_addr,
and ice_vsi_add_vlan to avoid incrementing the accounting fields such as
vsi->num_vlan or vf->num_mac.
This logic works correctly for the case where only a single VSI has added a
given switch filter.
When a second VSI adds the same switch filter, the driver converts the
existing filter from an ICE_FWD_TO_VSI filter into an ICE_FWD_TO_VSI_LIST
filter. This saves switch resources, by ensuring that multiple VSIs can
re-use the same filter.
The ice_add_update_vsi_list() function is responsible for doing this
conversion. When first converting a filter from the FWD_TO_VSI into
FWD_TO_VSI_LIST, it checks if the VSI being added is the same as the
existing rule's VSI. In such a case it returns -EEXIST.
However, when the switch rule has already been converted to a
FWD_TO_VSI_LIST, the logic is different. Adding a new VSI in this case just
requires extending the VSI list entry. The logic for checking if the rule
already exists in this case returns 0 instead of -EEXIST.
This breaks the accounting logic mentioned above, so the counters for how
many MAC and VLAN filters exist for a given VF or VSI no longer accurately
reflect the actual count. This breaks other code which relies on these
counts.
In typical usage this primarily affects such filters generally shared by
multiple VSIs such as VLAN 0, or broadcast and multicast MAC addresses.
Fix this by correctly reporting -EEXIST in the case of adding the same VSI
to a switch rule already converted to ICE_FWD_TO_VSI_LIST.
Fixes: 9daf8208dd ("ice: Add support for switch filter programming")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After vsi setup refactor commit 6624e780a5 ("ice: split ice_vsi_setup
into smaller functions") ice_cfg_sw_lldp function which removes rx rule
directing LLDP packets to vsi is moved from ice_vsi_release to
ice_vsi_decfg function. ice_vsi_decfg is used in more cases than just in
vsi_release resulting in unnecessary removal of rx lldp packets handling
switch rule. This leads to lldp packets being dropped after a change number
of channels via ethtool.
This patch moves ice_cfg_sw_lldp function that removes rx lldp sw rule back
to ice_vsi_release function.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Reported-by: Matěj Grégr <mgregr@netx.as>
Closes: https://lore.kernel.org/intel-wired-lan/1be45a76-90af-4813-824f-8398b69745a9@netx.as/T/#u
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use previously implemented SF aux driver. It is probe during SF
activation and remove after deactivation.
Implement set/get hw_address and set/get state as basic devlink ops for
subfunction.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement add / delete vlan for subfunction type VSI.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Flow for creating Tx topology is the same as for VF port representors,
but the devlink port is stored in different place (sf->devlink_port).
When creating VF devlink lock isn't taken, when creating subfunction it
is. Setting Tx topology function needs to take this lock, check if it
was taken before to not do it twice.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Subfunction port representor needs the basic netdevice ops to work
correctly. Create them.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now there is another type of port representor. Correct checking if
parent device is ready to reflect also new PR type.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add check for subfunction before setting target VSI. It is needed for PF
in switchdev mode but not for subfunction (even in switchdev mode).
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement attaching and detaching SF port representor. It is done in the
same way as the VF port representor.
SF port representor is always added or removed with devlink
lock taken.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keep the same flow of port representor creation, but instead of general
attach function create helpers for specific representor type.
Store function pointer for add and remove representor.
Type of port representor can be also known based on VSI type, but it
is more clean to have it directly saved in port representor structure.
Add devlink lock for whole port representor creation and destruction.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Configure netdevice for subfunction usecase. Mostly it is reusing ops
from the PF netdevice.
SF netdev is linked to devlink port registered after SF activation.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement subfunction driver. It is probe when subfunction port is
activated.
VSI is already created. During the probe VSI is being configured.
MAC unicast and broadcast filter is added to allow traffic to pass.
Store subfunction pointer in VSI struct. The same is done for VF
pointer. Make union of subfunction and VF pointer as only one of them
can be set with one VSI.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allocate devlink for subfunction instance.
Create header file for subfunction device. Define subfunction device
structure there as it is needed for devlink allocation.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When subfunction VSI is open the same code as for PF VSI should be
executed. Also when up is complete. Reflect that in code by adding
subfunction VSI to consideration.
In case of stopping, PF doesn't have additional tasks, so the same
is with subfunction VSI.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement devlink port handlers responsible for ethernet type devlink
subfunctions. Create subfunction devlink port and setup all resources
needed for a subfunction netdev to operate. Configure new VSI for each
new subfunction, initialize and configure interrupts and Tx/Rx resources.
Set correct MAC filters and create new netdev.
For now, subfunction is limited to only one Tx/Rx queue pair.
Only allocate new subfunction VSI with devlink port new command.
Allocate and free subfunction MSIX interrupt vectors using new API
calls with pci_msix_alloc_irq_at and pci_msix_free_irq.
Support both automatic and manual subfunction numbers. If no subfunction
number is provided, use xa_alloc to pick a number automatically. This
will find the first free index and use that as the number. This reduces
burden on users in the simple case where a specific number is not
required. It may also be slightly faster to check that a number exists
since xarray lookup should be faster than a linear scan of the dyn_ports
xarray.
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make some of the netdevice_ops functions visible from outside for
another VSI type created netdev.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add required plumbing for new VSI type dedicated to devlink subfunctions.
Make sure that the vsi is properly configured and destroyed. Also allow
loading XDP and AF_XDP sockets.
The first implementation of devlink subfunctions supports only one Tx/Rx
queue pair per given subfunction.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The responsibility for reporting of RX software timestamp has moved to
the core layer (see __ethtool_get_ts_info()), remove usage from the
device drivers.
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After XDP configuration is completed, we bring the interface up
unconditionally, regardless of its state before the call to .ndo_bpf().
Preserve the information whether the interface had to be brought down and
later bring it up only in such case.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Locking used in ice_qp_ena() and ice_qp_dis() does pretty much nothing,
because ICE_CFG_BUSY is a state flag that is supposed to be set in a PF
state, not VSI one. Therefore it does not protect the queue pair from
e.g. reset.
Remove ICE_CFG_BUSY locking from ice_qp_dis() and ice_qp_ena().
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Consider the following scenario:
.ndo_bpf() | ice_prepare_for_reset() |
________________________|_______________________________________|
rtnl_lock() | |
ice_down() | |
| test_bit(ICE_VSI_DOWN) - true |
| ice_dis_vsi() returns |
ice_up() | |
| proceeds to rebuild a running VSI |
.ndo_bpf() is not the only rtnl-locked callback that toggles the interface
to apply new configuration. Another example is .set_channels().
To avoid the race condition above, act only after reading ICE_VSI_DOWN
under rtnl_lock.
Fixes: 0f9d5027a7 ("ice: Refactor VSI allocation, deletion and rebuild flow")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If VSI rebuild is pending, .ndo_bpf() can attach/detach the XDP program on
VSI without applying new ring configuration. When unconfiguring the VSI, we
can encounter the state in which there is an XDP program but no XDP rings
to destroy or there will be XDP rings that need to be destroyed, but no XDP
program to indicate their presence.
When unconfiguring, rely on the presence of XDP rings rather then XDP
program, as they better represent the current state that has to be
destroyed.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The main threat to data consistency in ice_xdp() is a possible asynchronous
PF reset. It can be triggered by a user or by TX timeout handler.
XDP setup and PF reset code access the same resources in the following
sections:
* ice_vsi_close() in ice_prepare_for_reset() - already rtnl-locked
* ice_vsi_rebuild() for the PF VSI - not protected
* ice_vsi_open() - already rtnl-locked
With an unfortunate timing, such accesses can result in a crash such as the
one below:
[ +1.999878] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 14
[ +2.002992] ice 0000:b1:00.0: Registered XDP mem model MEM_TYPE_XSK_BUFF_POOL on Rx ring 18
[Mar15 18:17] ice 0000:b1:00.0 ens801f0np0: NETDEV WATCHDOG: CPU: 38: transmit queue 14 timed out 80692736 ms
[ +0.000093] ice 0000:b1:00.0 ens801f0np0: tx_timeout: VSI_num: 6, Q 14, NTC: 0x0, HW_HEAD: 0x0, NTU: 0x0, INT: 0x4000001
[ +0.000012] ice 0000:b1:00.0 ens801f0np0: tx_timeout recovery level 1, txqueue 14
[ +0.394718] ice 0000:b1:00.0: PTP reset successful
[ +0.006184] BUG: kernel NULL pointer dereference, address: 0000000000000098
[ +0.000045] #PF: supervisor read access in kernel mode
[ +0.000023] #PF: error_code(0x0000) - not-present page
[ +0.000023] PGD 0 P4D 0
[ +0.000018] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ +0.000023] CPU: 38 PID: 7540 Comm: kworker/38:1 Not tainted 6.8.0-rc7 #1
[ +0.000031] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.082620210524 08/26/2021
[ +0.000036] Workqueue: ice ice_service_task [ice]
[ +0.000183] RIP: 0010:ice_clean_tx_ring+0xa/0xd0 [ice]
[...]
[ +0.000013] Call Trace:
[ +0.000016] <TASK>
[ +0.000014] ? __die+0x1f/0x70
[ +0.000029] ? page_fault_oops+0x171/0x4f0
[ +0.000029] ? schedule+0x3b/0xd0
[ +0.000027] ? exc_page_fault+0x7b/0x180
[ +0.000022] ? asm_exc_page_fault+0x22/0x30
[ +0.000031] ? ice_clean_tx_ring+0xa/0xd0 [ice]
[ +0.000194] ice_free_tx_ring+0xe/0x60 [ice]
[ +0.000186] ice_destroy_xdp_rings+0x157/0x310 [ice]
[ +0.000151] ice_vsi_decfg+0x53/0xe0 [ice]
[ +0.000180] ice_vsi_rebuild+0x239/0x540 [ice]
[ +0.000186] ice_vsi_rebuild_by_type+0x76/0x180 [ice]
[ +0.000145] ice_rebuild+0x18c/0x840 [ice]
[ +0.000145] ? delay_tsc+0x4a/0xc0
[ +0.000022] ? delay_tsc+0x92/0xc0
[ +0.000020] ice_do_reset+0x140/0x180 [ice]
[ +0.000886] ice_service_task+0x404/0x1030 [ice]
[ +0.000824] process_one_work+0x171/0x340
[ +0.000685] worker_thread+0x277/0x3a0
[ +0.000675] ? preempt_count_add+0x6a/0xa0
[ +0.000677] ? _raw_spin_lock_irqsave+0x23/0x50
[ +0.000679] ? __pfx_worker_thread+0x10/0x10
[ +0.000653] kthread+0xf0/0x120
[ +0.000635] ? __pfx_kthread+0x10/0x10
[ +0.000616] ret_from_fork+0x2d/0x50
[ +0.000612] ? __pfx_kthread+0x10/0x10
[ +0.000604] ret_from_fork_asm+0x1b/0x30
[ +0.000604] </TASK>
The previous way of handling this through returning -EBUSY is not viable,
particularly when destroying AF_XDP socket, because the kernel proceeds
with removal anyway.
There is plenty of code between those calls and there is no need to create
a large critical section that covers all of them, same as there is no need
to protect ice_vsi_rebuild() with rtnl_lock().
Add xdp_state_lock mutex to protect ice_vsi_rebuild() and ice_xdp().
Leaving unprotected sections in between would result in two states that
have to be considered:
1. when the VSI is closed, but not yet rebuild
2. when VSI is already rebuild, but not yet open
The latter case is actually already handled through !netif_running() case,
we just need to adjust flag checking a little. The former one is not as
trivial, because between ice_vsi_close() and ice_vsi_rebuild(), a lot of
hardware interaction happens, this can make adding/deleting rings exit
with an error. Luckily, VSI rebuild is pending and can apply new
configuration for us in a managed fashion.
Therefore, add an additional VSI state flag ICE_VSI_REBUILD_PENDING to
indicate that ice_xdp() can just hot-swap the program.
Also, as ice_vsi_rebuild() flow is touched in this patch, make it more
consistent by deconfiguring VSI when coalesce allocation fails.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, netif_queue_set_napi() is called from ice_vsi_rebuild() that is
not rtnl-locked when called from the reset. This creates the need to take
the rtnl_lock just for a single function and complicates the
synchronization with .ndo_bpf. At the same time, there no actual need to
fill napi-to-queue information at this exact point.
Fill napi-to-queue information when opening the VSI and clear it when the
VSI is being closed. Those routines are already rtnl-locked.
Also, rewrite napi-to-queue assignment in a way that prevents inclusion of
XDP queues, as this leads to out-of-bounds writes, such as one below.
[ +0.000004] BUG: KASAN: slab-out-of-bounds in netif_queue_set_napi+0x1c2/0x1e0
[ +0.000012] Write of size 8 at addr ffff889881727c80 by task bash/7047
[ +0.000006] CPU: 24 PID: 7047 Comm: bash Not tainted 6.10.0-rc2+ #2
[ +0.000004] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0014.082620210524 08/26/2021
[ +0.000003] Call Trace:
[ +0.000003] <TASK>
[ +0.000002] dump_stack_lvl+0x60/0x80
[ +0.000007] print_report+0xce/0x630
[ +0.000007] ? __pfx__raw_spin_lock_irqsave+0x10/0x10
[ +0.000007] ? __virt_addr_valid+0x1c9/0x2c0
[ +0.000005] ? netif_queue_set_napi+0x1c2/0x1e0
[ +0.000003] kasan_report+0xe9/0x120
[ +0.000004] ? netif_queue_set_napi+0x1c2/0x1e0
[ +0.000004] netif_queue_set_napi+0x1c2/0x1e0
[ +0.000005] ice_vsi_close+0x161/0x670 [ice]
[ +0.000114] ice_dis_vsi+0x22f/0x270 [ice]
[ +0.000095] ice_pf_dis_all_vsi.constprop.0+0xae/0x1c0 [ice]
[ +0.000086] ice_prepare_for_reset+0x299/0x750 [ice]
[ +0.000087] pci_dev_save_and_disable+0x82/0xd0
[ +0.000006] pci_reset_function+0x12d/0x230
[ +0.000004] reset_store+0xa0/0x100
[ +0.000006] ? __pfx_reset_store+0x10/0x10
[ +0.000002] ? __pfx_mutex_lock+0x10/0x10
[ +0.000004] ? __check_object_size+0x4c1/0x640
[ +0.000007] kernfs_fop_write_iter+0x30b/0x4a0
[ +0.000006] vfs_write+0x5d6/0xdf0
[ +0.000005] ? fd_install+0x180/0x350
[ +0.000005] ? __pfx_vfs_write+0x10/0xA10
[ +0.000004] ? do_fcntl+0x52c/0xcd0
[ +0.000004] ? kasan_save_track+0x13/0x60
[ +0.000003] ? kasan_save_free_info+0x37/0x60
[ +0.000006] ksys_write+0xfa/0x1d0
[ +0.000003] ? __pfx_ksys_write+0x10/0x10
[ +0.000002] ? __x64_sys_fcntl+0x121/0x180
[ +0.000004] ? _raw_spin_lock+0x87/0xe0
[ +0.000005] do_syscall_64+0x80/0x170
[ +0.000007] ? _raw_spin_lock+0x87/0xe0
[ +0.000004] ? __pfx__raw_spin_lock+0x10/0x10
[ +0.000003] ? file_close_fd_locked+0x167/0x230
[ +0.000005] ? syscall_exit_to_user_mode+0x7d/0x220
[ +0.000005] ? do_syscall_64+0x8c/0x170
[ +0.000004] ? do_syscall_64+0x8c/0x170
[ +0.000003] ? do_syscall_64+0x8c/0x170
[ +0.000003] ? fput+0x1a/0x2c0
[ +0.000004] ? filp_close+0x19/0x30
[ +0.000004] ? do_dup2+0x25a/0x4c0
[ +0.000004] ? __x64_sys_dup2+0x6e/0x2e0
[ +0.000002] ? syscall_exit_to_user_mode+0x7d/0x220
[ +0.000004] ? do_syscall_64+0x8c/0x170
[ +0.000003] ? __count_memcg_events+0x113/0x380
[ +0.000005] ? handle_mm_fault+0x136/0x820
[ +0.000005] ? do_user_addr_fault+0x444/0xa80
[ +0.000004] ? clear_bhb_loop+0x25/0x80
[ +0.000004] ? clear_bhb_loop+0x25/0x80
[ +0.000002] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ +0.000005] RIP: 0033:0x7f2033593154
Fixes: 080b0c8d6d ("ice: Fix ASSERT_RTNL() warning during certain scenarios")
Fixes: 91fdbce7e8 ("ice: Add support in the driver for associating queue with napi")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ethtool callbacks can be executed while reset is in progress and try to
access deleted resources, e.g. getting coalesce settings can result in a
NULL pointer dereference seen below.
Reproduction steps:
Once the driver is fully initialized, trigger reset:
# echo 1 > /sys/class/net/<interface>/device/reset
when reset is in progress try to get coalesce settings using ethtool:
# ethtool -c <interface>
BUG: kernel NULL pointer dereference, address: 0000000000000020
PGD 0 P4D 0
Oops: Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 11 PID: 19713 Comm: ethtool Tainted: G S 6.10.0-rc7+ #7
RIP: 0010:ice_get_q_coalesce+0x2e/0xa0 [ice]
RSP: 0018:ffffbab1e9bcf6a8 EFLAGS: 00010206
RAX: 000000000000000c RBX: ffff94512305b028 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff9451c3f2e588 RDI: ffff9451c3f2e588
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: ffff9451c3f2e580 R11: 000000000000001f R12: ffff945121fa9000
R13: ffffbab1e9bcf760 R14: 0000000000000013 R15: ffffffff9e65dd40
FS: 00007faee5fbe740(0000) GS:ffff94546fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000020 CR3: 0000000106c2e005 CR4: 00000000001706f0
Call Trace:
<TASK>
ice_get_coalesce+0x17/0x30 [ice]
coalesce_prepare_data+0x61/0x80
ethnl_default_doit+0xde/0x340
genl_family_rcv_msg_doit+0xf2/0x150
genl_rcv_msg+0x1b3/0x2c0
netlink_rcv_skb+0x5b/0x110
genl_rcv+0x28/0x40
netlink_unicast+0x19c/0x290
netlink_sendmsg+0x222/0x490
__sys_sendto+0x1df/0x1f0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x82/0x160
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7faee60d8e27
Calling netif_device_detach() before reset makes the net core not call
the driver when ethtool command is issued, the attempt to execute an
ethtool command during reset will result in the following message:
netlink error: No such device
instead of NULL pointer dereference. Once reset is done and
ice_rebuild() is executing, the netif_device_attach() is called to allow
for ethtool operations to occur again in a safe manner.
Fixes: fcea6f3da5 ("ice: Add stats and ethtool support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-08-26 (ice)
This series contains updates to ice driver only.
Jake implements and uses rd32_poll_timeout to replace a jiffies loop for
calling ice_sq_done. The rd32_poll_timeout() function is designed to allow
simplifying other places in the driver where we need to read a register
until it matches a known value.
Jake, Bruce, and Przemek update ice_debug_cq() to be more robust, and more
useful for tracing control queue messages sent and received by the device
driver.
Jake rewords several commands in the ice_control.c file which previously
referred to the "Admin queue" when they were actually generic functions
usable on any control queue.
Jake removes the unused and unnecessary cmd_buf array allocation for send
queues. This logic originally was going to be useful if we ever implemented
asynchronous completion of transmit messages. This support is unlikely to
materialize, so the overhead of allocating a command buffer is unnecessary.
Sergey improves the log messages when the ice driver reports that the NVM
version on the device is not supported by the driver. Now, these messages
include both the discovered NVM version and the requested/expected NVM
version.
Aleksandr Mishin corrects overallocation of memory related to adding
scheduler nodes.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Adjust over allocation of memory in ice_sched_add_root_node() and ice_sched_add_node()
ice: Report NVM version numbers on mismatch during load
ice: remove unnecessary control queue cmd_buf arrays
ice: reword comments referring to control queues
ice: stop intermixing AQ commands/responses debug dumps
ice: do not clutter debug logs with unused data
ice: improve debug print for control queue messages
ice: implement and use rd32_poll_timeout for ice_sq_done timeout
====================
Link: https://patch.msgid.link/20240826224655.133847-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to get and set configuration of Embedded SYNC feature
on the ice driver dpll pins.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20240822222513.255179-3-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_sched_add_root_node() and ice_sched_add_node() there are calls to
devm_kcalloc() in order to allocate memory for array of pointers to
'ice_sched_node' structure. But incorrect types are used as sizeof()
arguments in these calls (structures instead of pointers) which leads to
over allocation of memory.
Adjust over allocation of memory by correcting types in devm_kcalloc()
sizeof() arguments.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Report NVM version numbers (both detected and expected) when a mismatch b/w
driver and firmware is detected. This provides more useful information
about which NVM version the driver expects, rather than requiring manual
code inspection.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver allocates a cmd_buf array in addition to the desc_buf array.
This array stores an ice_sq_cd command details structure for each entry in
the control queue ring.
The contents of the structure are copied from the value passed in via
ice_sq_send_cmd, and include only a pointer to storage for the write back
descriptor contents.
Originally this array was intended to support asynchronous completion
including features such as a callback function. This support was never
implemented. All that exists today is needless copying and resetting of a
cmd_buf array that is otherwise functionally unused.
Since we do not plan to implement asynchronous completions, drop this
unnecessary memory and logic. This saves memory for each control queue, and
avoids the pointless copying and memset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Many comments in ice_controlq.c use the term "Admin queue" despite the code
being intended for arbitrary control queues, not just the Admin queue.
Reword the comments to make it clear that this code is the generic control
queue logic that is shared by all of the control queues, and is not
specific to the Admin queue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_debug_cq() function is called to generate a debug log of control
queue messages both sent and received. It currently does this over a
potential total of 6 different printk invocations.
The main logic prints over 4 calls to ice_debug():
1. The metadata including opcode, flags, datalength and return value.
2. The cookie in the descriptor.
3. The parameter values.
4. The address for the databuffer.
In addition, if the descriptor has a data buffer, it can be logged with two
additional prints:
5. A message indicating the start of the data buffer.
6. The actual data buffer, printed using print_hex_dump_debug.
This can lead to trouble in the event that two different PFs are logging
messages. The messages become intermixed and it may not be possible to
determine which part of the output belongs to which control queue message.
To fix this, it needs to be possible to unambiguously determine which
messages belong together. This is trivial for the messages that comprise
the main printing. Combine them together into a single invocation of
ice_debug().
The message containing a hex-dump of the data buffer is a bit more
complicated. This is printed separately as part of print_hex_dump_debug.
This function takes a prefix, which is currently always set to
KBUILD_MODNAME. Extend this prefix to include the buffer address for the
databuffer, which is printed as part of the main print, and which is
guaranteed to be unique for each buffer.
Refactor the ice_debug_array(), introducing an ice_debug_array_w_prefix().
Build the prefix by combining KBUILD_MODNAME with the databuffer address
using snprintf().
These changes make it possible to unambiguously determine what data belongs
to what control queue message.
Reported-by: Jacek Wierzbicki <jacek.wierzbicki@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, debug logs are unnecessarily cluttered with the contents of
command data buffers even if the receiver of that command (i.e. FW or MBX)
are not told to read the buffer. Change to only log command data buffers
when the RD flag (indicates receiver needs to read the buffer) is set.
Continue to log response data buffer when the returned datalen is non-zero.
Also, rename a local variable to reflect what is in the hardware
specification and how it is used elsewhere in the code, use local variables
instead of duplicating endian conversions unnecessarily and remove an
unnecessary assignment.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_debug_cq function is called to print debug data for a control queue
descriptor in multiple places. This includes both before we send a message
on a transmit queue, after the writeback completion of a message on the
transmit queue, and when we receive a message on a receive queue.
This function does not include data about *which* control queue the message
is on, nor whether it was what we sent to the queue or what we received
from the queue.
Modify ice_debug_cq to take two extra parameters, a pointer to the control
queue and a boolean indicating if this was a response or a command. Improve
the debug messages by replacing "CQ CMD" with a string indicating which
specific control queue (based on cq->qtype) and whether this was a command
sent by the PF or a response from the queue.
This helps make the log output easier to understand and consume when
debugging.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_sq_done function is used to check the control queue head register
and determine whether or not the control queue processing is done. This
function is called in a loop checking against jiffies for a specified
timeout.
The pattern of reading a register in a loop until a condition is true or a
timeout is reached is a relatively common pattern. In fact, the kernel
provides a read_poll_timeout function implementing this behavior in
<linux/iopoll.h>
Use of read_poll_timeout is preferred over directly coding these loops.
However, using it in the ice driver is a bit more difficult because of the
rd32 wrapper. Implement a rd32_poll_timeout wrapper based on
read_poll_timeout.
Refactor ice_sq_done to use rd32_poll_timeout, replacing the loop calling
ice_sq_done in ice_sq_send_cmd. This simplifies the logic down to a single
ice_sq_done() call.
The implementation of rd32_poll_timeout uses microseconds for its timeout
value, so update the CQ timeout macros used to be specified in microseconds
units as well instead of using HZ for jiffies.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.h
c948c0973d ("bnxt_en: Don't clear ntuple filters and rss contexts during ethtool ops")
f2878cdeb7 ("bnxt_en: Add support to call FW to update a VNIC")
Link: https://patch.msgid.link/20240822210125.1542769-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BIT() is unsigned long but ->pu.flg_msk and ->pu.flg_val are u64 type.
On 32 bit systems, unsigned long is a u32 and the mismatch between u32
and u64 will break things for the high 32 bits.
Fixes: 9a4c07aaa0 ("ice: add parser execution main loop")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/ddc231a8-89c1-4ff4-8704-9198bcb41f8d@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use always the same pf id in devlink port number. When doing
pass-through the PF to VM bus info func number can be any value.
Fixes: 2ae0aa4758 ("ice: Move devlink port to PF/VF struct")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When working on multi-buffer packet on arch that has PAGE_SIZE >= 8192,
truesize is calculated and stored in xdp_buff::frame_sz per each
processed Rx buffer. This means that frame_sz will contain the truesize
based on last received buffer, but commit 1dc1a7e7f4 ("ice:
Centrallize Rx buffer recycling") assumed this value will be constant
for each buffer, which breaks the page recycling scheme and mess up the
way we update the page::page_offset.
To fix this, let us work on constant truesize when PAGE_SIZE >= 8192
instead of basing this on size of a packet read from Rx descriptor. This
way we can simplify the code and avoid calculating truesize per each
received frame and on top of that when using
xdp_update_skb_shared_info(), current formula for truesize update will
be valid.
This means ice_rx_frame_truesize() can be removed altogether.
Furthermore, first call to it within ice_clean_rx_irq() for 4k PAGE_SIZE
was redundant as xdp_buff::frame_sz is initialized via xdp_init_buff()
in ice_vsi_cfg_rxq(). This should have been removed at the point where
xdp_buff struct started to be a member of ice_rx_ring and it was no
longer a stack based variable.
There are two fixes tags as my understanding is that the first one
exposed us to broken truesize and page_offset handling and then second
introduced broken skb_shared_info update in ice_{construct,build}_skb().
Reported-and-tested-by: Luiz Capitulino <luizcap@redhat.com>
Closes: https://lore.kernel.org/netdev/8f9e2a5c-fd30-4206-9311-946a06d031bb@redhat.com/
Fixes: 1dc1a7e7f4 ("ice: Centrallize Rx buffer recycling")
Fixes: 2fba7dc515 ("ice: Add support for XDP multi-buffer on Rx side")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For bigger PAGE_SIZE archs, ice driver works on 3k Rx buffers.
Therefore, ICE_LAST_OFFSET should take into account ICE_RXBUF_3072, not
ICE_RXBUF_2048.
Fixes: 7237f5b0db ("ice: introduce legacy Rx flag")
Suggested-by: Luiz Capitulino <luizcap@redhat.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Architectures that have PAGE_SIZE >= 8192 such as arm64 should act the
same as x86 currently, meaning reuse of a page should only take place
when no one else is busy with it.
Do two things independently of underlying PAGE_SIZE:
- store the page count under ice_rx_buf::pgcnt
- then act upon its value vs ice_rx_buf::pagecnt_bias when making the
decision regarding page reuse
Fixes: 2b245cb294 ("ice: Implement transmit and NAPI support")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for offloading cls U32 filters. Only "skbedit queue_mapping"
and "drop" actions are supported. Also, only "ip" and "802_3" tc
protocols are allowed. The PF must advertise the VIRTCHNL_VF_OFFLOAD_TC_U32
capability flag.
Since the filters will be enabled via the FD stage at the PF, a new type
of FDIR filters is added and the existing list and state machine are used.
The new filters can be used to configure flow directors based on raw
(binary) pattern in the rx packet.
Examples:
0. # tc qdisc add dev enp175s0v0 ingress
1. Redirect UDP from src IP 192.168.2.1 to queue 12:
# tc filter add dev <dev> protocol ip ingress u32 \
match u32 0x45000000 0xff000000 at 0 \
match u32 0x00110000 0x00ff0000 at 8 \
match u32 0xC0A80201 0xffffffff at 12 \
match u32 0x00000000 0x00000000 at 24 \
action skbedit queue_mapping 12 skip_sw
2. Drop all ICMP:
# tc filter add dev <dev> protocol ip ingress u32 \
match u32 0x45000000 0xff000000 at 0 \
match u32 0x00010000 0x00ff0000 at 8 \
match u32 0x00000000 0x00000000 at 24 \
action drop skip_sw
3. Redirect ICMP traffic from MAC 3c:fd:fe:a5:47:e0 to queue 7
(note proto: 802_3):
# tc filter add dev <dev> protocol 802_3 ingress u32 \
match u32 0x00003CFD 0x0000ffff at 4 \
match u32 0xFEA547E0 0xffffffff at 8 \
match u32 0x08004500 0xffffff00 at 12 \
match u32 0x00000001 0x000000ff at 20 \
match u32 0x0000 0x0000 at 40 \
action skbedit queue_mapping 7 skip_sw
Notes on matches:
1 - All intermediate fields that are needed to parse the correct PTYPE
must be provided (in e.g. 3: Ethernet Type 0x0800 in MAC, IP version
and IP length: 0x45 and protocol: 0x01 (ICMP)).
2 - The last match must provide an offset that guarantees all required
headers are accounted for, even if the last header is not matched.
For example, in #2, the last match is 4 bytes at offset 24 starting
from IP header, so the total is 14 (MAC) + 24 + 4 = 42, which is the
sum of MAC+IP+ICMP headers.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable VFs to create FDIR filters from raw binary patterns.
The corresponding processes for raw flow are added in the
Parse / Create / Destroy stages.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The SWAP Flag in the FDIR Programming Descriptor doesn't work properly,
it is always set and cannot be unset (hardware bug). Thus, add a method
to effectively disable the FDIR SWAP option by setting the FDSWAP instead
of FDINSET registers.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add API ice_parser_profile_init() to init a parser profile based on
a parser result and a mask buffer. The ice_parser_profile struct is used
by the low level FXP engine to create HW profile/field vectors.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for the vxlan, geneve, ecpri UDP tunnels through the
following APIs:
- ice_parser_vxlan_tunnel_set()
- ice_parser_geneve_tunnel_set()
- ice_parser_ecpri_tunnel_set()
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add API ice_parser_dvm_set() to support turning on/off the parser's double
vlan mode.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the following internal helper functions:
- ice_bst_tcam_match():
to perform ternary match on boost TCAM.
- ice_pg_cam_match():
to perform parse graph key match in cam table.
- ice_pg_nm_cam_match():
to perform parse graph key no match in cam table.
- ice_ptype_mk_tcam_match():
to perform ptype markers match in tcam table.
- ice_flg_redirect():
to redirect parser flags to packet flags.
- ice_xlt_kb_flag_get():
to aggregate 64 bit packet flag into 16 bit key builder flags.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Parse the following DDP sections:
- ICE_SID_RXPARSER_IMEM into an array of struct ice_imem_item
- ICE_SID_RXPARSER_METADATA_INIT into an array of struct ice_metainit_item
- ICE_SID_RXPARSER_CAM or ICE_SID_RXPARSER_PG_SPILL into an array of
struct ice_pg_cam_item
- ICE_SID_RXPARSER_NOMATCH_CAM or ICE_SID_RXPARSER_NOMATCH_SPILL into an
array of struct ice_pg_nm_cam_item
- ICE_SID_RXPARSER_CAM into an array of ice_bst_tcam_item
- ICE_SID_LBL_RXPARSER_TMEM into an array of ice_lbl_item
- ICE_SID_RXPARSER_MARKER_PTYPE into an array of ice_ptype_mk_tcam_item
- ICE_SID_RXPARSER_MARKER_GRP into an array of ice_mk_grp_item
- ICE_SID_RXPARSER_PROTO_GRP into an array of ice_proto_grp_item
- ICE_SID_RXPARSER_FLAG_REDIR into an array of ice_flg_rd_item
- ICE_SID_XLT_KEY_BUILDER_SW, ICE_SID_XLT_KEY_BUILDER_ACL,
ICE_SID_XLT_KEY_BUILDER_FD and ICE_SID_XLT_KEY_BUILDER_RSS into
struct ice_xlt_kb
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new parser module which can parse a packet in binary and generate
information like ptype, protocol/offset pairs and flags which can be later
used to feed the FXP profile creation directly.
Add skeleton of the create and destroy APIs:
ice_parser_create()
ice_parser_destroy()
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
marvell/otx2 and mvpp2 do not support setting different
keys for different RSS contexts. Contexts have separate
indirection tables but key is shared with all other contexts.
This is likely fine, indirection table is the most important
piece.
Don't report the key-related parameters from such drivers.
This prevents driver-errors, e.g. otx2 always writes
the main key, even when user asks to change per-context key.
The second reason is that without this change tracking
the keys by the core gets complicated. Even if the driver
correctly reject setting key with rss_context != 0,
change of the main key would have to be reflected in
the XArray for all additional contexts.
Since the additional contexts don't have their own keys
not including the attributes (in Netlink speak) seems
intuitive. ethtool CLI seems to deal with it just fine.
Having to set the flag in majority of the drivers is
a bit tedious but not reporting the key is a safer
default.
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ac21add254 ("ice: Implement driver functionality to dump fec
statistics") introduces obtaining FEC correctable and uncorrectable
stats per netdev in ICE driver. Unfortunately the assignment of values
to fec_stats structure has been done incorrectly. This commit fixes the
assignments.
Fixes: ac21add254 ("ice: Implement driver functionality to dump fec statistics")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Block HW write access for the driver while the device is in reset to
avoid potential race condition and access to the PTP HW in
non-nominal state which could lead to undesired effects
Fixes: 4aad533596 ("ice: add individual interrupt allocation")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_cfg_txq_interrupt() internally handles XDP Tx ring. Do not use
ice_for_each_tx_ring() in ice_qvec_cfg_msix() as this causing us to
treat XDP ring that belongs to queue vector as Tx ring and therefore
misconfiguring the interrupts.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is read by data path and modified from process context on remote cpu
so it is needed to use WRITE_ONCE to clear the pointer.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
xsk_buff_pool pointers that ice ring structs hold are updated via
ndo_bpf that is executed in process context while it can be read by
remote CPU at the same time within NAPI poll. Use synchronize_net()
after pointer update and {READ,WRITE}_ONCE() when working with mentioned
pointer.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This so we prevent Tx timeout issues. One of conditions checked on
running in the background dev_watchdog() is netif_carrier_ok(), so let
us turn it off when we disable the queues that belong to a q_vector
where XSK pool is being configured. Turn carrier on in ice_qp_ena()
only when ice_get_link_status() tells us that physical link is up.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Don't bail out right when spotting an error within ice_qp_{dis,ena}()
but rather track error and go through whole flow of disabling and
enabling queue pair.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Given that ice_qp_dis() is called under rtnl_lock, synchronize_net() can
be called instead of synchronize_rcu() so that XDP rings can finish its
job in a faster way. Also let us do this as earlier in XSK queue disable
flow.
Additionally, turn off regular Tx queue before disabling irqs and NAPI.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When ice driver is spammed with multiple xdpsock instances and flow
control is enabled, there are cases when Rx queue gets stuck and unable
to reflect the disable state in QRX_CTRL register. Similar issue has
previously been addressed in commit 13a6233b03 ("ice: Add support to
enable/disable all Rx queues before waiting").
To workaround this, let us simply not wait for a disabled state as later
patch will make sure that regardless of the encountered error in the
process of disabling a queue pair, the Rx queue will be enabled.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Address a scenario in which XSK ZC Tx produces descriptors to XDP Tx
ring when link is either not yet fully initialized or process of
stopping the netdev has already started. To avoid this, add checks
against carrier readiness in ice_xsk_wakeup() and in ice_xmit_zc().
One could argue that bailing out early in ice_xsk_wakeup() would be
sufficient but given the fact that we produce Tx descriptors on behalf
of NAPI that is triggered for Rx traffic, the latter is also needed.
Bringing link up is an asynchronous event executed within
ice_service_task so even though interface has been brought up there is
still a time frame where link is not yet ok.
Without this patch, when AF_XDP ZC Tx is used simultaneously with stack
Tx, Tx timeouts occur after going through link flap (admin brings
interface down then up again). HW seem to be unable to transmit
descriptor to the wire after HW tail register bump which in turn causes
bit __QUEUE_STATE_STACK_XOFF to be set forever as
netdev_tx_completed_queue() sees no cleaned bytes on the input.
Fixes: 126cdfe100 ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
catching COVID, so relatively short PR. Including fixes from bpf
and netfilter.
Current release - regressions:
- tcp: process the 3rd ACK with sk_socket for TFO and MPTCP
Current release - new code bugs:
- l2tp: protect session IDR and tunnel session list with one lock,
make sure the state is coherent to avoid a warning
- eth: bnxt_en: update xdp_rxq_info in queue restart logic
- eth: airoha: fix location of the MBI_RX_AGE_SEL_MASK field
Previous releases - regressions:
- xsk: require XDP_UMEM_TX_METADATA_LEN to actuate tx_metadata_len,
the field reuses previously un-validated pad
Previous releases - always broken:
- tap/tun: drop short frames to prevent crashes later in the stack
- eth: ice: add a per-VF limit on number of FDIR filters
- af_unix: disable MSG_OOB handling for sockets in sockmap/sockhash
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9OsH
-----END PGP SIGNATURE-----
Merge tag 'net-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and netfilter.
A lot of networking people were at a conference last week, busy
catching COVID, so relatively short PR.
Current release - regressions:
- tcp: process the 3rd ACK with sk_socket for TFO and MPTCP
Current release - new code bugs:
- l2tp: protect session IDR and tunnel session list with one lock,
make sure the state is coherent to avoid a warning
- eth: bnxt_en: update xdp_rxq_info in queue restart logic
- eth: airoha: fix location of the MBI_RX_AGE_SEL_MASK field
Previous releases - regressions:
- xsk: require XDP_UMEM_TX_METADATA_LEN to actuate tx_metadata_len,
the field reuses previously un-validated pad
Previous releases - always broken:
- tap/tun: drop short frames to prevent crashes later in the stack
- eth: ice: add a per-VF limit on number of FDIR filters
- af_unix: disable MSG_OOB handling for sockets in sockmap/sockhash"
* tag 'net-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (34 commits)
tun: add missing verification for short frame
tap: add missing verification for short frame
mISDN: Fix a use after free in hfcmulti_tx()
gve: Fix an edge case for TSO skb validity check
bnxt_en: update xdp_rxq_info in queue restart logic
tcp: process the 3rd ACK with sk_socket for TFO/MPTCP
selftests/bpf: Add XDP_UMEM_TX_METADATA_LEN to XSK TX metadata test
xsk: Require XDP_UMEM_TX_METADATA_LEN to actuate tx_metadata_len
bpf: Fix a segment issue when downgrading gso_size
net: mediatek: Fix potential NULL pointer dereference in dummy net_device handling
MAINTAINERS: make Breno the netconsole maintainer
MAINTAINERS: Update bonding entry
net: nexthop: Initialize all fields in dumped nexthops
net: stmmac: Correct byte order of perfect_match
selftests: forwarding: skip if kernel not support setting bridge fdb learning limit
tipc: Return non-zero value from tipc_udp_addr2str() on error
netfilter: nft_set_pipapo_avx2: disable softinterrupts
ice: Fix recipe read procedure
ice: Add a per-VF limit on number of FDIR filters
net: bonding: correctly annotate RCU in bond_should_notify_peers()
...
Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases to
get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions. It's not all that useful for a "write a whole driver
in rust" type of thing, but the firmware bindings do help out the
phy rust drivers, and the driver core bindings give a solid base on
which others can start their work. There is still a long way to go
here before we have a multitude of rust drivers being added, but
it's a great first step.
- driver core const api changes. This reached across all bus types,
and there are some fix-ups for some not-common bus types that
linux-next and 0-day testing shook out. This work is being done to
help make the rust bindings more safe, as well as the C code, moving
toward the end-goal of allowing us to put driver structures into
read-only memory. We aren't there yet, but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZqH+aQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoOQCfVBdLcBjEDAGh3L8qHRGMPy4rV2EAoL/r+zKm
cJEYtJpGtWX6aAtugm9E
=ZyJV
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
When ice driver reads recipes from firmware information about
need_pass_l2 and allow_pass_l2 flags is not stored correctly.
Those flags are stored as one bit each in ice_sw_recipe structure.
Because of that, the result of checking a flag has to be casted to bool.
Note that the need_pass_l2 flag currently works correctly, because
it's stored in the first bit.
Fixes: bccd9bce29 ("ice: Add guard rule when creating FDB in switchdev")
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While the iavf driver adds a s/w limit (128) on the number of FDIR
filters that the VF can request, a malicious VF driver can request more
than that and exhaust the resources for other VFs.
Add a similar limit in ice.
CC: stable@vger.kernel.org
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Suggested-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
patchsets (devmem among them) did not make it in time.
Core & protocols
----------------
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT.
- Use flex array for netdevice priv area, ensure its cache alignment.
- Add a sysctl knob to allow user to specify a default rto_min at socket
init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful.
- Support scheduling transmission of packets based on CLOCK_TAI.
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned off
using cpusets.
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address.
- Allow configuration of multipath hash seed, to both allow synchronizing
hashing of two routers, and preventing partial accidental sync.
- Improve TCP compliance with RFC 9293 for simultaneous connect().
- Support sending NAT keepalives in IPsec ESP in UDP states. Userspace
IKE daemon had to do this before, but the kernel can better keep
track of it.
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled.
- Introduce IPPROTO_SMC for selecting SMC when socket is created.
- Allow UDP GSO transmit from devices with no checksum offload.
- openvswitch: add packet sampling via psample, separating the sampled
traffic from "upcall" packets sent to user space for forwarding.
- nf_tables: shrink memory consumption for transaction objects.
Things we sprinkled into general kernel code
--------------------------------------------
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver
for QCA6390).
- Add IRQ information in sysfs for auxiliary bus.
- Introduce guard definition for local_lock.
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures.
BPF
---
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered.
- Add new kfuncs for a generic, open-coded bits iterator.
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head.
- Support resilient split BTF which cuts down on duplication and makes
BTF as compact as possible WRT BTF from modules.
- Add support for dumping kfunc prototypes from BTF which enables both
detecting as well as dumping compilable prototypes for kfuncs.
- riscv64 BPF JIT improvements in particular to add 12-argument support
for BPF trampolines and to utilize bpf_prog_pack for the latter.
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs.
Driver API
----------
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose.
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits.
- Track additional RSS contexts in the core, make sure configuration
changes don't break them.
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated ESP
data paths.
- Support updating firmware on SFP modules.
Tests and tooling
-----------------
- mptcp: use net/lib.sh to manage netns.
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints.
- openvswitch: make test self-contained (don't depend on OvS CLI tools).
Drivers
-------
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead
and skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps
to catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead of
in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmaWjBwACgkQMUZtbf5S
IrvuSRAAkJuEzTRqgURBCe4eNEQde6mJJig7l2CKHwCbFiHZpRkFHf8qKbcGWbL6
uLW33SWnKtJVDhxVKWHLq635XW7BAa80YhqGw21GDi+mIEhWXZglHj3xbXNxsMfE
4eg/kG4BkfYWFmHaXOwVWV/mr7nXf6j7WmXNeXEi32ufE1j0OL+YlQenKnMj8yP2
j9JmYa2Chwppng1SblHmcjmGkdNVwFhStKeCG+2K7v06wdDH/QYBlbgUv9gw/cxp
NlW//wgiaeX40U4O3kDwt9C+LDoh+0VrDDeVdQ+IsScLtY3PhAzEoKolFYTq2HSr
I1JpoaHNnyNsJq3DZrACQ5WlH4yDn6C2EUB6dxNnFaI9F1ZPsi+7MTl6Sei1AklD
TuQTj/lxOACBwW2Q77NU72uoxiIUauesGPHcnrAFuoCIEhZF0mso7k59BvrXhsOP
QwcLbQdc1YHNkqv/Vc7NBY+ruMsYB+5Ubbhhj2p27dp/CWFIwxI29fze4dn2uhO6
ejHN3mbqwPdSzg12YJtM6Iq61Cnwo2eVSvhTxl+ZVSZtI4nu2arzR+y7QTYmNrXP
6tkgVN9UsWeLl2xJ8wyyqL5mcvNHP2rPXWZ2X56iTaa26m+UlleeQ7YRaYtQAAr0
Ec/vlDMX64SwHhd+qwE99DXGQf2g+KklHKSLsnajJUVrWFTlRI0=
=opz8
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Not much excitement - a handful of large patchsets (devmem among them)
did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at
socket init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow
synchronizing hashing of two routers, and preventing partial
accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states.
Userspace IKE daemon had to do this before, but the kernel can
better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the
sampled traffic from "upcall" packets sent to user space for
forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head
- Support resilient split BTF which cuts down on duplication and
makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables
both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument
support for BPF trampolines and to utilize bpf_prog_pack for the
latter
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration
changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI
tools)
Drivers:
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead and
skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps to
catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead
of in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
tcp: Replace strncpy() with strscpy()
wifi: ath12k: fix build vs old compiler
tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
eth: fbnic: Add L2 address programming
eth: fbnic: Add basic Rx handling
eth: fbnic: Add basic Tx handling
eth: fbnic: Add link detection
eth: fbnic: Add initial messaging to notify FW of our presence
eth: fbnic: Implement Rx queue alloc/start/stop/free
eth: fbnic: Implement Tx queue alloc/start/stop/free
eth: fbnic: Allocate a netdevice and napi vectors with queues
eth: fbnic: Add FW communication mechanism
eth: fbnic: Add message parsing for FW messages
eth: fbnic: Add register init to set PCIe/Ethernet device config
eth: fbnic: Allocate core device specific structures and devlink interface
eth: fbnic: Add scaffolding for Meta's NIC driver
PCI: Add Meta Platforms vendor ID
net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
...
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
ice: Switch API optimizations
Marcin Szycik says:
Optimize the process of creating a recipe in the switch block by removing
duplicate switch ID words and changing how result indexes are fitted into
recipes. In many cases this can decrease the number of recipes required to
add a certain set of rules, potentially allowing a more varied set of rules
to be created. Total rule count will also increase, since less words will
be left unused/wasted. There are only 64 rules available in total, so every
one counts.
After this modification, many fields and some structs became unused or were
simplified, resulting in overall simpler implementation.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Add tracepoint for adding and removing switch rules
ice: Remove unused members from switch API
ice: Optimize switch recipe creation
ice: remove unused recipe bookkeeping data
ice: Simplify bitmap setting in adding recipe
ice: Remove reading all recipes before adding a new one
ice: Remove unused struct ice_prot_lkup_ext members
====================
Link: https://patch.msgid.link/20240711181312.2019606-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
initialized in the code path anyway right after on the ARM arch
timer and the ARM global timer (Li kunyu)
- Fix a race condition in the interrupt leading to a deadlock on the
SH CMT driver. Note that this fix was not tested on the platform
using this timer but the fix seems reasonable enough to be picked
confidently (Niklas Söderlund)
- Increase the rating of the gic-timer and use the configured width
clocksource register on the MIPS architecture (Jiaxun Yang)
- Add the DT bindings for the TMU on the Renesas platforms (Geert
Uytterhoeven)
- Add the DT bindings for the SOPHGO SG2002 clint on RiscV (Thomas
Bonnefille)
- Add the rtl-otto timer driver along with the DT bindings for the
Realtek platform (Chris Packham)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmaRQh0ACgkQqDIjiipP
6E+rfQgAqkAWZ9BjswxV8Fg+Hj+a1cSohKjDczqitQF5rJm25X5VvMwlXVa3XQGm
yemh4tKPpll02LOiYCTyqOWzNrkVS9VsoBd5rrYjRX5aSv7UD35EXklLj4P/INwX
O9CRGD6aK4Xbw66xxheYHSSh+2iRs2x2mq61+/VdcIBlAwpQo+vx7McRoJZZI+2t
NFIXw8RF5dDlmmAaqiB0WnPAtcOK3SDo9fu1LEAX1ZAzvbZriLo7XLnL7ibySWVe
BW1n7Ore6PN5Dvz7jMfTsOQsgAlVv6MPfp/s4EDqMfBLVqXNirzXrdhiee/ahnYP
vyzQyU5HPCMiIYS45mhJF0OyDd3wyw==
=wuYA
-----END PGP SIGNATURE-----
Merge tag 'timers-v6.11-rc1' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clocksource/event driver updates from Daniel Lezcano:
- Remove unnecessary local variables initialization as they will be
initialized in the code path anyway right after on the ARM arch
timer and the ARM global timer (Li kunyu)
- Fix a race condition in the interrupt leading to a deadlock on the
SH CMT driver. Note that this fix was not tested on the platform
using this timer but the fix seems reasonable enough to be picked
confidently (Niklas Söderlund)
- Increase the rating of the gic-timer and use the configured width
clocksource register on the MIPS architecture (Jiaxun Yang)
- Add the DT bindings for the TMU on the Renesas platforms (Geert
Uytterhoeven)
- Add the DT bindings for the SOPHGO SG2002 clint on RiscV (Thomas
Bonnefille)
- Add the rtl-otto timer driver along with the DT bindings for the
Realtek platform (Chris Packham)
Link: https://lore.kernel.org/all/91cd05de-4c5d-4242-a381-3b8a4fe6a2a2@linaro.org
Since the port representors are added one by one there is no need to do
eswitch rebuild. Each port representor is detached and attached in VF
reset path.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for driver-specific devlink local_forwarding param.
Supported values are "enabled", "disabled" and "prioritized".
Default configuration is set to "enabled".
Add documentation in networking/devlink/ice.rst.
In previous generations of Intel NICs the transmit scheduler was only
limited by PCIe bandwidth when scheduling/assigning hairpin-bandwidth
between VFs. Changes to E810 HW design introduced scheduler limitation,
so that available hairpin-bandwidth is bound to external port speed.
In order to address this limitation and enable NFV services such as
"service chaining" a knob to adjust the scheduler config was created.
Driver can send a configuration message to the FW over admin queue and
internal FW logic will reconfigure HW to prioritize and add more BW to
VF to VF traffic. An end result, for example, 10G port will no longer
limit hairpin-bandwidth to 10G and much higher speeds can be achieved.
Devlink local_forwarding param set to "prioritized" enables higher
hairpin-bandwitdh on related PFs. Configuration is applicable only to
8x10G and 4x25G cards.
Changing local_forwarding configuration will trigger CORER reset in
order to take effect.
Example command to change current value:
devlink dev param set pci/0000:b2:00.3 name local_forwarding \
value prioritized \
cmode runtime
Co-developed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are moving away from the Sourceforge email address. Rather than
removing or updating the email for the affected entries, remove the
MODULE_AUTHOR altogether as its usage is incorrect [1].
Link: https://lore.kernel.org/netdev/20200626115236.7f36d379@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/ [1]
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Alexander Lobakin <aleksander.lobakin@intel.com> # libeth, libie
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Track the number of rules and recipes added to switch. Add a tracepoint to
ice_aq_sw_rules(), which shows both rule and recipe count. This information
can be helpful when designing a set of rules to program to the hardware, as
it shows where the practical limit is. Actual limits are known (64 recipes,
32k rules), but it's hard to translate these values to how many rules the
*user* can actually create, because of extra metadata being implicitly
added, and recipe/rule chaining. Chaining combines several recipes/rules to
create a larger recipe/rule, so one large rule added by the user might
actually consume multiple rules from hardware perspective.
Rule counter is simply incremented/decremented in ice_aq_sw_rules(), since
all rules are added or removed via it.
Counting recipes is harder, as recipes can't be removed (only overwritten).
Recipes added via ice_aq_add_recipe() could end up being unused, when
there is an error in later stages of rule creation. Instead, track the
allocation and freeing of recipes, which should reflect the actual usage of
recipes (if something fails after recipe(s) were created, caller should
free them). Also, a number of recipes are loaded from NVM by default -
initialize the recipe counter with the number of these recipes on switch
initialization.
Example configuration:
cd /sys/kernel/tracing
echo function > current_tracer
echo ice_aq_sw_rules > set_ftrace_filter
echo ice_aq_sw_rules > set_event
echo 1 > tracing_on
cat trace
Example output:
tc-4097 [069] ...1. 787.595536: ice_aq_sw_rules <-ice_rem_adv_rule
tc-4097 [069] ..... 787.595705: ice_aq_sw_rules: rules=9 recipes=15
tc-4098 [057] ...1. 787.652033: ice_aq_sw_rules <-ice_add_adv_rule
tc-4098 [057] ..... 787.652201: ice_aq_sw_rules: rules=10 recipes=16
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove several members of struct ice_sw_recipe and struct
ice_prot_lkup_ext. Remove struct ice_recp_grp_entry and struct
ice_pref_recipe_group, since they are now unused as well.
All of the deleted members were only written to and never read, so it's
pointless to keep them.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when creating switch recipes, switch ID is always added as the
first word in every recipe. There are only 5 words in a recipe, so one
word is always wasted. This is also true for the last recipe, which stores
result indexes (in case of chain recipes). Therefore the maximum usable
length of a chain recipe is 4 * 4 = 16 words. 4 words in a recipe, 4
recipes that can be chained (using a 5th one for result indexes).
Current max size chained recipe:
0: smmmm
1: smmmm
2: smmmm
3: smmmm
4: srrrr
Where:
s - switch ID
m - regular match (e.g. ipv4 src addr, udp dst port, etc.)
r - result index
Switch ID does not actually need to be present in every recipe, only in one
of them (in case of chained recipe). This frees up to 8 extra words:
3 from recipes in the middle (because first recipe still needs to have
switch ID), and 5 from one extra recipe (because now the last recipe also
does not have switch ID, so it can chain 1 more recipe).
Max size chained recipe after changes:
0: smmmm
1: Mmmmm
2: Mmmmm
3: Mmmmm
4: MMMMM
5: Rrrrr
Extra usable words available after this change are highlighted with capital
letters.
Changing how switch ID is added is not straightforward, because it's not a
regular lookup. Its FV index and mask can't be determined based on protocol
+ offset pair read from package and instead need to be added manually.
Additionally, change how result indexes are added. Currently they are
always inserted in a new recipe at the end. Example for 13 words, (with
above optimization, switch ID being one of the words):
0: smmmm
1: mmmmm
2: mmmxx
3: rrrxx
Where:
x - unused word
In this and some other cases, the result indexes can be moved just after
last matches because there are unused words, saving one recipe. Example
for 13 words after both optimizations:
0: smmmm
1: mmmmm
2: mmmrr
Note how one less result index is needed in this case, because the last
recipe does not need to "link" to itself.
There are cases when adding an additional recipe for result indexes cannot
be avoided. In that cases result indexes are all put in the last recipe.
Example for 14 words after both optimizations:
0: smmmm
1: mmmmm
2: mmmmx
3: rrrxx
With these two changes, recipes/rules are more space efficient, allowing
more to be created in total.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove root_buf from recipe struct. Its only usage was in ice_find_recp(),
where if recipe had an inverse action, it was skipped, but actually the
driver never adds inverse actions, so effectively it was pointless.
Without root_buf, the recipe data element in ice_add_sw_recipe() does
not need to be persistent and can also be automatically deallocated with
__free, which nicely simplifies unroll.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove unnecessary size checks when copying bitmaps in ice_add_sw_recipe()
and replace them with compile time assert. Check if the bitmaps are equal
size, as they are copied both ways.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Co-developed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The content of the first read recipe is used as a template when adding a
recipe. It isn't needed - only prune index is directly set from there. Set
it in the code instead. Also, now there's no need to set rid and lookup
indexes to 0, as the whole recipe buffer is initialized to 0.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove field_off as it's never used.
Remove done bitmap, as its value is only checked and never assigned.
Reusing sub-recipes while creating new root recipes is currently not
supported in the driver.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To debug link issues in the field, serdes Tx/Rx equalizer values
help to determine the health of serdes lane.
Extend 'ethtool -d' option to dump serdes Tx/Rx equalizer.
The following list of equalizer param is supported
a. rx_equalization_pre2
b. rx_equalization_pre1
c. rx_equalization_post1
d. rx_equalization_bflf
e. rx_equalization_bfhf
f. rx_equalization_drate
g. tx_equalization_pre1
h. tx_equalization_pre3
i. tx_equalization_atten
j. tx_equalization_post1
k. tx_equalization_pre2
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anil Samal <anil.samal@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240709202951.2103115-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To debug link issues in the field, it is paramount to
dump fec corrected/uncorrected block counts from firmware.
Firmware requires PCS quad number and PCS port number to
read FEC statistics. Current driver implementation does
not maintain above physical properties of a port.
Add new driver API to derive physical properties of an input
port.These properties include PCS quad number, PCS port number,
serdes lane count, primary serdes lane number.
Extend ethtool option '--show-fec' to support fec statistics.
The IEEE standard mandates two sets of counters:
- 30.5.1.1.17 aFECCorrectedBlocks
- 30.5.1.1.18 aFECUncorrectableBlocks
Standard defines above statistics per lane but current
implementation supports total FEC statistics per port
i.e. sum of all lane per port. Find sample output below
FEC parameters for ens21f0np0:
Supported/Configured FEC encodings: Auto RS BaseR
Active FEC encoding: RS
Statistics:
corrected_blocks: 0
uncorrectable_blocks: 0
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anil Samal <anil.samal@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240709202951.2103115-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current driver implementation for Sideband Queue supports a
fixed flag (ICE_AQ_FLAG_RD). To retrieve FEC statistics from
firmware, Sideband Queue command is used with a different flag.
Extend API for Sideband Queue command to use 'flags' as input
argument.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anil Samal <anil.samal@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240709202951.2103115-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Do not use _test_bit() macro for testing bit. The proper macro for this
is one without underline.
_test_bit() is what test_bit() was prior to const-optimization. It
directly calls arch_test_bit(), i.e. the arch-specific implementation
(or the generic one). It's strictly _internal_ and shouldn't be used
anywhere outside the actual test_bit() macro.
test_bit() is a wrapper which checks whether the bitmap and the bit
number are compile-time constants and if so, it calls the optimized
function which evaluates this call to a compile-time constant as well.
If either of them is not a compile-time constant, it just calls _test_bit().
test_bit() is the actual function to use anywhere in the kernel.
IOW, calling _test_bit() avoids potential compile-time optimizations.
The sensors is not a compile-time constant, thus most probably there
are no object code changes before and after the patch.
But anyway, we shouldn't call internal wrappers instead of
the actual API.
Fixes: 4da71a77fc ("ice: read internal temperature sensor")
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240702171459.2606611-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver receives requests for configuring pins via the .enable
callback of the PTP clock object. These requests come into the driver
with flags which modify the requested behavior from userspace. Current
implementation in ice does not reject flags that it doesn't support.
This causes the driver to incorrectly apply requests with such flags as
PTP_PEROUT_DUTY_CYCLE, or any future flags added by the kernel which it
is not yet aware of.
Fix this by properly validating flags in both ice_ptp_cfg_perout and
ice_ptp_cfg_extts. Ensure that we check by bit-wise negating supported
flags rather than just checking and rejecting known un-supported flags.
This is preferable, as it ensures better compatibility with future
kernels.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240702171459.2606611-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ice_ptp_extts_event() function can race with ice_ptp_release() and
result in a NULL pointer dereference which leads to a kernel panic.
Panic occurs because the ice_ptp_extts_event() function calls
ptp_clock_event() with a NULL pointer. The ice driver has already
released the PTP clock by the time the interrupt for the next external
timestamp event occurs.
To fix this, modify the ice_ptp_extts_event() function to check the
PTP state and bail early if PTP is not ready.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240702171459.2606611-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extts events are disabled and enabled by the application ts2phc.
However, in case where the driver is removed when the application is
running, a specific extts event remains enabled and can cause a kernel
crash.
As a side effect, when the driver is reloaded and application is started
again, remaining extts event for the channel from a previous run will
keep firing and the message "extts on unexpected channel" might be
printed to the user.
To avoid that, extts events shall be disabled when PTP is released.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240702171459.2606611-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allocate and initialize struct ice_adapter object only once per physical
card instead of once per port. This is not a big deal by now, but we want
to extend this struct more and more in the near future. Our plans include
PTP stuff and a devlink instance representing whole-device/physical card.
Transactions requiring to be sleep-able (like those doing user (here ice)
memory allocation) must be performed with an additional (on top of xarray)
mutex. Adding it here removes need to xa_lock() manually.
Since this commit is a reimplementation of ice_adapter_get(), a rather new
scoped_guard() wrapper for locking is used to simplify the logic.
It's worth to mention that xa_insert() use gives us both slot reservation
and checks if it is already filled, what simplifies code a tiny bit.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Admin queue command for shutdown AQ contains a flag to indicate driver
unload. However, the flag is always set in the driver, even for resets. It
can cause the firmware to consider driver as unloaded once the PF reset is
triggered on all ports of device, which could lead to unexpected results.
Add an additional function parameter to functions that shutdown AQ,
indicating whether the driver is actually unloading.
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow the driver to be compatible with different FW API versions based
on the device's MAC type. Currently, E810 is only compatible with one
FW API version. Now the driver can be compatible with different FW API
versions for both E810 and E830. For example, E810 FW API version is
1.5.0 and E830 is 1.7.0.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Check the return value from ice_vsi_rebuild() and prevent the usage of
incorrectly configured VSI.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Changing the MAC address of the VFs is currently unsupported via devlink.
Add the function handlers to set and get the HW address for the VFs.
Signed-off-by: Karthik Sundaravel <ksundara@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TC queues needs to be correctly updated when the number of queues on
a VSI is reconfigured, so netdev's queue and TC settings will be
dynamically adjusted and could accurately represent the underlying
hardware state after changes to the VSI queue counts.
Fixes: 0754d65bd4 ("ice: Add infrastructure for mqprio support via ndo_setup_tc")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of reset of VF VSI can be reallocated. To handle this case it
should be properly updated.
Reload representor as vsi->vsi_num can be different than the one stored
when representor was created.
Instead of only changing antispoof do whole VSI configuration for
eswitch.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is needed because subfunction port representor shouldn't configure
the source VSI during representor creation.
Move the code to separate function and call it only in case the VF port
representor is being created.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In case of subfunction lock will be taken for whole port creation and
removing. Do the same in VF case.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is used to get representor structure during cleaning.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
1e7962114c ("bnxt_en: Restore PTP tx_avail count in case of skb_pad() error")
165f87691a ("bnxt_en: add timestamping statistics support")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adding/updating VSI list rule, as well as allocating/freeing VSI list
resource are called several times with type ICE_SW_LKUP_LAST, which fails
because ice_update_vsi_list_rule() and ice_aq_alloc_free_vsi_list()
consider it invalid. Allow calling these functions with ICE_SW_LKUP_LAST.
This fixes at least one issue in switchdev mode, where the same rule with
different action cannot be added, e.g.:
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF1_PR
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF2_PR
Fixes: 0f94570d0c ("ice: allow adding advanced rules")
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240618210206.981885-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmZvTbAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGVksIAJEn4a9IVM8FNCJy
Dxo0BItD1/qJ5mLDptqUFRKlxInjbojofz5CyoeIeXb0DwRfB16ALXqNXAkd3APi
saoOpfjFsg2H2OqL9CHdkzWcJEAq2lDnL0zaOjumeDVu/EyeT+tC4e4hq1e6Bm0E
fPC5ms2b+07DF9Rg6/DW8yPbdM5n6Mz1bRd3fQOIgvpM3yGOyGztEBgTRub/ZUgH
5pNJauknFAZgdiWhgNpc+lPWYZbgHKULQPhUBPdVhDIXPtQNUlKgNTQc6+L0Nmbb
K1sG1q7FLeMJOTFGQfD4r26X5DNQUi894q/9SX8X7rcrECdJKcw2WjVyB4myADpf
ae2gP+A=
=XjWP
-----END PGP SIGNATURE-----
Merge tag 'v6.10-rc4' into driver-core-next
We need the driver core and sysfs fixes in here to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
