Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec7711 ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.
For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:
'skb->len == 1600' from the first fragment
size = lstatus & BD_LENGTH_MASK; # 1602
size -= ETH_FCS_LEN; # 1598
size -= skb->len; # -2
Since the size is unsigned, it wraps around and causes a BUG later in
the packet handling, as shown below:
kernel BUG at ./include/linux/skbuff.h:2068!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c021ec60] skb_pull+0x24/0x44
LR [c01e2fbc] gfar_clean_rx_ring+0x498/0x690
Call Trace:
[df7edeb0] [c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable)
[df7edf20] [c01e33a8] gfar_poll_rx_sq+0x3c/0x9c
[df7edf40] [c023352c] net_rx_action+0x21c/0x274
[df7edf90] [c0329000] __do_softirq+0xd8/0x240
[df7edff0] [c000c108] call_do_irq+0x24/0x3c
[c0597e90] [c00041dc] do_IRQ+0x64/0xc4
[c0597eb0] [c000d920] ret_from_except+0x0/0x18
--- interrupt: 501 at arch_cpu_idle+0x24/0x5c
Change the size to a signed integer and then trim off any part of the
FCS that was received prior to the last fragment.
Fixes: 6c389fc931 ("gianfar: fix size of scatter-gathered frames")
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to LS1021A RM, the value of PAL can be set so that the start of the
IP header in the receive data buffer is aligned to a 32-bit boundary. Normally,
setting PAL = 2 provides minimal padding to ensure such alignment of the IP
header.
However every incoming packet's 8-byte time stamp will be inserted into the
packet data buffer as padding alignment bytes when hardware time stamping is
enabled.
So we set the padding 8+2 here to avoid the flooded alignment faults:
root@128:~# cat /proc/cpu/alignment
User: 0
System: 17539 (inet_gro_receive+0x114/0x2c0)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 17539
User faults: 2 (fixup)
Also shown when exception report enablement
CPU: 0 PID: 161 Comm: irq/66-eth1_g0_ Not tainted 4.1.21-rt13-WR8.0.0.0_preempt-rt #16
Hardware name: Freescale LS1021A
[<8001b420>] (unwind_backtrace) from [<8001476c>] (show_stack+0x20/0x24)
[<8001476c>] (show_stack) from [<807cfb48>] (dump_stack+0x94/0xac)
[<807cfb48>] (dump_stack) from [<80025d70>] (do_alignment+0x720/0x958)
[<80025d70>] (do_alignment) from [<80009224>] (do_DataAbort+0x40/0xbc)
[<80009224>] (do_DataAbort) from [<80015398>] (__dabt_svc+0x38/0x60)
Exception stack(0x86ad1cc0 to 0x86ad1d08)
1cc0: f9b3e080 86b3d072 2d78d287 00000000 866816c0 86b3d05e 86e785d0 00000000
1ce0: 00000011 0000000e 80840ab0 86ad1d3c 86ad1d08 86ad1d08 806d7fc0 806d806c
1d00: 40070013 ffffffff
[<80015398>] (__dabt_svc) from [<806d806c>] (inet_gro_receive+0x114/0x2c0)
[<806d806c>] (inet_gro_receive) from [<80660eec>] (dev_gro_receive+0x21c/0x3c0)
[<80660eec>] (dev_gro_receive) from [<8066133c>] (napi_gro_receive+0x44/0x17c)
[<8066133c>] (napi_gro_receive) from [<804f0538>] (gfar_clean_rx_ring+0x39c/0x7d4)
[<804f0538>] (gfar_clean_rx_ring) from [<804f0bf4>] (gfar_poll_rx_sq+0x58/0xe0)
[<804f0bf4>] (gfar_poll_rx_sq) from [<80660b10>] (net_rx_action+0x27c/0x43c)
[<80660b10>] (net_rx_action) from [<80033638>] (do_current_softirqs+0x1e0/0x3dc)
[<80033638>] (do_current_softirqs) from [<800338c4>] (__local_bh_enable+0x90/0xa8)
[<800338c4>] (__local_bh_enable) from [<8008025c>] (irq_forced_thread_fn+0x70/0x84)
[<8008025c>] (irq_forced_thread_fn) from [<800805e8>] (irq_thread+0x16c/0x244)
[<800805e8>] (irq_thread) from [<8004e490>] (kthread+0xe8/0x104)
[<8004e490>] (kthread) from [<8000fda8>] (ret_from_fork+0x14/0x2c)
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
19057 392 0 19449 4bf9 drivers/net/ethernet/freescale/gianfar.o
File size After adding 'const':
text data bss dec hex filename
19249 192 0 19441 4bf1 drivers/net/ethernet/freescale/gianfar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In spite of switching to paged allocation of Rx buffers, the driver still
called dma_unmap_single() in the Rx queues tear-down path.
The DMA region unmapping code in free_skb_rx_queue() basically predates
the introduction of paged allocation to the driver. While being refactored,
it apparently hasn't reflected the change in the DMA API usage by its
counterpart gfar_new_page().
As a result, setting an interface to the DOWN state now yields the following:
# ip link set eth2 down
fsl-gianfar ffe24000.ethernet: DMA-API: device driver frees DMA memory with wrong function [device address=0x000000001ecd0000] [size=40]
------------[ cut here ]------------
WARNING: CPU: 1 PID: 189 at lib/dma-debug.c:1123 check_unmap+0x8e0/0xa28
CPU: 1 PID: 189 Comm: ip Tainted: G O 4.9.5 #1
task: dee73400 task.stack: dede2000
NIP: c02101e8 LR: c02101e8 CTR: c0260d74
REGS: dede3bb0 TRAP: 0700 Tainted: G O (4.9.5)
MSR: 00021000 <CE,ME> CR: 28002222 XER: 00000000
GPR00: c02101e8 dede3c60 dee73400 000000b6 dfbd033c dfbd36c4 1f622000 dede2000
GPR08: 00000007 c05b1634 1f622000 00000000 22002484 100a9904 00000000 00000000
GPR16: 00000000 db4c849c 00000002 db4c8480 00000001 df142240 db4c84bc 00000000
GPR24: c0706148 c0700000 00029000 c07552e8 c07323b4 dede3cb8 c07605e0 db535540
NIP [c02101e8] check_unmap+0x8e0/0xa28
LR [c02101e8] check_unmap+0x8e0/0xa28
Call Trace:
[dede3c60] [c02101e8] check_unmap+0x8e0/0xa28 (unreliable)
[dede3cb0] [c02103b8] debug_dma_unmap_page+0x88/0x9c
[dede3d30] [c02dffbc] free_skb_resources+0x2c4/0x404
[dede3d80] [c02e39b4] gfar_close+0x24/0xc8
[dede3da0] [c0361550] __dev_close_many+0xa0/0xf8
[dede3dd0] [c03616f0] __dev_close+0x2c/0x4c
[dede3df0] [c036b1b8] __dev_change_flags+0xa0/0x174
[dede3e10] [c036b2ac] dev_change_flags+0x20/0x60
[dede3e30] [c03e130c] devinet_ioctl+0x540/0x824
[dede3e90] [c0347dcc] sock_ioctl+0x134/0x298
[dede3eb0] [c0111814] do_vfs_ioctl+0xac/0x854
[dede3f20] [c0111ffc] SyS_ioctl+0x40/0x74
[dede3f40] [c000f290] ret_from_syscall+0x0/0x3c
--- interrupt: c01 at 0xff45da0
LR = 0xff45cd0
Instruction dump:
811d001c 7c66482e 813d0020 9061000c 807f000c 5463103a 7cc6182e 3c60c052
386309ac 90c10008 4cc63182 4826b845 <0fe00000> 4bfffa60 3c80c052 388402c4
---[ end trace 695ae6d7ac1d0c47 ]---
Mapped at:
[<c02e22a8>] gfar_alloc_rx_buffs+0x178/0x248
[<c02e3ef0>] startup_gfar+0x368/0x570
[<c036aeb4>] __dev_open+0xdc/0x150
[<c036b1b8>] __dev_change_flags+0xa0/0x174
[<c036b2ac>] dev_change_flags+0x20/0x60
Even though the issue was discovered in 4.9 kernel, the code in question
is identical in the current net and net-next trees.
Fixes: 75354148ce ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver using dev_alloc_page() must not reuse a page that had to
use emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of the RX
ring buffer would suffer from drops.
Fixes: 75354148ce ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current scatter-gather logic in gianfar is flawed, since
it does not consider the eTSEC's RxBD 'Data Length' field is
context depening: for the last fragment it contains the full
frame size, while fragments contain the fragment size, which
equals the value written to register MRBLR.
This causes data corruption as soon as the hardware starts
to fragment receiving frames. As a result, the size of
fragmented frames is increased by
(nr_frags - 1) * MRBLR
We first noticed this issue working with DSA, where an ICMP
request sized 1472 bytes causes the scatter-gather logic to
kick in. The full Ethernet frame (1518) gets increased by
DSA (4), GMAC_FCB_LEN (8), and FSL_GIANFAR_DEV_HAS_TIMER
(priv->padding=8) to a total of 1538 octets, which is
fragmented by the hardware and reconstructed by the driver
to a 3074 octet frame.
This patch fixes the problem by adjusting the size of
the last fragment.
It was tested by setting MRBLR to different multiples of
64, proving correct scatter-gather operation on frames
with up to 9000 octets in size.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/ethernet/freescale/gianfar.c:2278:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transmit hardware timestamping is enabled, an additional
TxBD would be added and would be set as the last TxBD with TXBD_LAST
and TXBD_INTERRUPT. However this has been broken by a patch recently.
This made the software couldn't get transmit hardware timestamps and
resulted in call trace. So, this patch is to fix this issue.
Fixes: 48963b4492 ("gianfar: Remove redundant ops for do_tstamp
from xmit()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable workaround for MPC8548E erratum eTSEC 106,
"Excess delays when transmitting TOE=1 large frames".
(see commit 53fad77375 "gianfar: Enable eTSEC-20 erratum w/a
for P2020 Rev1")
This erratum was fixed in Rev 3.1.x.
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix endianness for the 64-bit hardware timestamp value with
be64_to_cpu to support both PowerPC platforms and ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timestamp BD status updates that can be merged into the
same "do_tstamp" block, no need for extra save/restore
to the BD area. The code is more readable too.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the mapping of the head BD before the mapping of fragments.
The TOE (h/w offload) decision logic block can be also moved up
(as the TOE flag belongs to the head BD), resulting in more
localized code (TOE logic vs BD mapping code blocks).
Note that, for this h/w, the R (status) bit for the head BD of a S/G
frame needs to be written last for a reliable transmission.
For the fragmented skb case, a local variable is used to temporarily
store the status info of the first BD, replacing a BD status read.
A merge of 2 "if(do_tstamp)" blocks was also possible.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 15bf176db1 ("gianfar: Don't enable the Filer w/o the
Parser"), 'TSEC' model controllers (for example as seen on MPC8541E)
always have 8 bytes stripped from the front of received frames.
Only 'eTSEC' gianfar controllers have the RX Filer capability (amongst
other enhancements). Previously this was treated as always enabled
for both 'TSEC' and 'eTSEC' controllers.
In commit 15bf176db1 ("gianfar: Don't enable the Filer w/o the Parser")
a subtle change was made to the setting of 'uses_rxfcb' to effectively
always set it (since 'rx_filer_enable' was always true). This had the
side-effect of always stripping 8 bytes from the front of received frames
on 'TSEC' type controllers.
We now only enable the RX Filer capability on controller types that
support it, thereby avoiding the issue for 'TSEC' type controllers.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver can be built on arm64 but relies on NO_IRQ to check the return
value of irq_of_parse_and_map() which fails to build on arm64 because the
architecture does not provide a NO_IRQ. Fix this to correctly check the
return value of irq_of_parse_and_map().
Even on ARM systems where the driver was previously used the check was
broken since on ARM NO_IRQ is -1 but irq_of_parse_and_map() returns 0 on
error.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
use of_property_read_bool() for testing bool property
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx BSY error interrupt indicates that a frame was
received and discarded due to lack of buffers, so it's
a rx ring overflow condition and has nothing to do with
with bad rx packets. Use the right counter.
BSY conditions happen when the SoC is under performance
stress. Doing *more* work in stress situations by trying
to schedule NAPI is not a good idea as the stressed system
becomes still more stressed. The Rx interrupt is already
at work making sure the NAPI is scheduled.
So calling gfar_receive() here does not help. This issue
was present since day 1.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under one unusual circumstance it's possible to wrongly set
FILREN without enabling PRSDEP as well in the RCTRL register,
against the hardware specifications. With the default config
this does not happen because the default Rx offloads (Rx csum
and Rx VLAN) properly enable PRSDEP. But if anyone disables
all these offloads (via ethtool), we get a wrong configuration
were the Rx flow classification and hashing, and other Filer
based features (e.g. wake-on-filer interrupt) won't work.
This patch fixes the issue.
Also, account for Rx FCB insertion which happens every time
PRSDEP is set.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables eTSEC's filer (Rx parser) and the FGPI Rx
interrupt (Filer General Purpose Interrupt) as a wakeup
source event.
Upon entering suspend state, the eTSEC filer is given
a rule to match incoming L2 unicast packets. A packet
matching the rule will be enqueued in the Rx ring and
a FGPI Rx interrupt will be asserted by the filer to
wakeup the system. Other packet types will be dropped.
On resume the filer table is restored to the content
before entering suspend state.
The set of rules from gfar_filer_config_wol() could be
extended to implement other WoL capabilities as well.
The "fsl,wake-on-filer" DT binding enables this capability
on certain platforms that feature the necessary power
management infrastructure, targeting mainly printing and
imaging applications.
(refer to Power Management section of the SoC Ref Man)
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_find_device() increments the phy struct device refcount, which
we need to properly balance. Add code to network drivers using this
function to ensure that the struct device refcount is correctly
balanced.
For xgene, looking back in the history, we should be able to use
of_phy_connect() with a zero flags argument for the DT case as this is
how the driver used to operate prior to de7b5b3d79 ("net: eth: xgene:
change APM X-Gene SoC platform ethernet to support ACPI").
This leaves the Cavium Thunder BGX unfixed; fixing this driver is a
complicated task, one which the maintainers need to be involved with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some MAC registers that need to be kept in sync
with the link state parameters, see adjust_link().
However, after a MAC soft reset default values for
these registers are assumed. In some cases (excepting
if down/ if up for example) adjust_link() does not see
that these values were reset to default because the
priv->old* link parameters were left unchanged.
So, reset the priv->old* link params as well during a
MAC reset to let adjust_link() restore the MAC link
settings to the actual link state values.
Fixes following case, for example:
Setting link to 100M, changing MTU (implies MAC reset),
link state remains unchanged to 100M but MAC registers
were reset to default (1G) breaking the connectivity w/
the PHY. Closing and re-opening the interface would
restore the MAC link parameters to the correct values.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.
The bflock is obviously obsoleted, its utility has been corroded
over time. The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines. The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device. With these changes, the TX processing is stopped before
gfar_halt().
Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume. Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.
Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)
Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
static void lock_tx_qs(struct gfar_private *priv)
^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
static void unlock_tx_qs(struct gfar_private *priv)
^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of defconfig consolidation using fragments, we'd like to be
able to have the same drivers enabled on 32-bit and 64-bit. Gianfar
happens to only exist on 32-bit systems, and when building the
resulting 64-bit kernel warnings were produced.
A couple of the warnings are trivial, but the rfbptr code has deeper
issues. It uses the virtual address as the DMA address, which again,
happens to work in the environments where this driver is currently
used, but is not the right thing to do.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation
support")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eTSEC h/w is capable of scatter/gather on the receive side
too if MAXFRM > MRBLR, when the allowed maximum Rx frame size
is set to be greater than the maximum Rx buffer size (MRBLR).
It's about time the driver makes use of this h/w capability,
by supporting fixed buffer sizes and Rx S/G.
The buffer size given to eTSEC for reception is fixed to
1536B (must be multiple of 64), which is the same default
buffer size as before, used to accommodate standard MTU
(1500B) size frames. As before, eTSEC can receive frames of
up to 9600B. Individual Rx buffers are mapped to page halves
(page size for eTSEC systems is 4KB). The skb is built around
the first buffer of a frame (using build_skb()). In case the
frame spans multiple buffers, the trailing buffers are added
as Rx fragments to the skb. The last buffer in frame is marked
by the L status flag. A mechanism is in place to reuse the pages
owned by the driver (for Rx) for subsequent receptions.
Supporting fixed size buffers allows the implementation of Rx S/G,
which in turn removes the memory pressure issues the driver had
before when MTU was set for jumbo frame reception.
Also, in most cases, the Rx path becomes faster due to Rx page
reusal, since the overhead of allocating new rx buffers is removed
from the fast path.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "ndev" instead of "dev", as the rx queue back pointer
to a net_device struct, to avoid name clashing with a
"struct device" reference. This prepares the addition of a
"struct device" back pointer to the rx queue structure.
Remove duplicated rxq registration in the process.
Move napi_gro_receive() outside gfar_process_frame().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several (long standing) problems about how the status
field of the rx buffer descriptor (rxbd) is currently handled on
the error path:
- too many unnecessary 16bit reads of the two halves of the rxbd
status field (32bit), also resulting in overuse of endianness
convesion macros;
- "bdp->status = RXBD_LARGE" makes no sense, since the "large"
flag is read only (only eTSEC can write it), and trying to clear
the other status bits is also error prone in this context
(most of the rx status bits are read only anyway).
This is fixed with a single 32bit read of the "status" field,
and then the appropriate 16bit shifting is applied to access
the various status bits or the rx frame length. Also corrected
the use of the RXBD_LARGE flag.
Additional fix:
"rx_over_errors" stat is incremented instead of "rx_crc_errors"
in case of RXBD_OVERRUN occurrence.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more common consumer/ producer index design to improve
rx buffer allocation. Instead of allocating a single new buffer
(skb) on each iteration, bundle the allocation of several rx
buffers at a time. This also opens the path for further memory
optimizations.
Remove useless check of rxq->rfbptr, since this patch touches
rx pause frame handling code as well. rxq->rfbptr is always
initialized as part of Rx BD ring init.
Remove redundant (and misleading) 'amount_pull' parameter.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device flag IFF_LIVE_ADDR_CHANGE to signal that
the device supports changing the hardware address when
the device is running.
This allows eth_mac_addr() to change the mac address
also when the network device's interface is open.
This capability is required by certain applications,
like bonding mode 6 (Adaptive Load Balancing).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle TxFIFO underrun exceptions outside the fast path.
A controller reset is more reliable in this exceptional
case, as opposed to re-enabling on-the-fly the Tx DMA.
As the controller reset is handled outside the fast path
by the reset_gfar() workqueue handler, the locking
scheme on the Tx path is significantly simplified.
Because the Tx processing (xmit queues and tx napi) is
disabled during controller reset, tstat access from xmit
does not require locking. So the scope of the txlock on
the processing path is now reduced to num_txbdfree, which
is shared only between process context (xmit) and softirq
(clean_tx_ring). As a result, the txlock must not guard
against interrupt context, and the spin_lock_irqsave()
from xmit can be replaced by spin_lock_bh(). Likewise,
the locking has been downgraded for clean_tx_ring().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read*() to get arch endian consistent
property values. Do some refactoring in the process.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conversion macros to correctly access the BE
fields of the Rx and Tx Frame Control Block on LE CPUs.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conversion macros to correctly access the BE
fields of the Rx and Tx Buffer Descriptors on LE CPUs.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC of-nodes may have children which are not queue-group nodes. For
example new-style fixed-phy declarations. These where incorrectly
assumed to be additional queue-groups.
Change the search to filter out any nodes which are not queue-groups,
or have been disabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ce29b0e2a ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.
Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed. gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cd1e65044d ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So we
don't need to do the check again in the platform device driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following spare warning:
drivers/net/ethernet/freescale/gianfar.c:3521:60: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:3521:60: expected unsigned int [noderef] <asn:2>*addr
drivers/net/ethernet/freescale/gianfar.c:3521:60: got unsigned int [usertype] *rfbptr
drivers/net/ethernet/freescale/gianfar.c:205:16: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:205:16: expected unsigned int [usertype] *rfbptr
drivers/net/ethernet/freescale/gianfar.c:205:16: got unsigned int [noderef] <asn:2>*<noident>
drivers/net/ethernet/freescale/gianfar.c:2918:44: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:2918:44: expected unsigned int [noderef] <asn:2>*addr
drivers/net/ethernet/freescale/gianfar.c:2918:44: got unsigned int [usertype] *rfbptr
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
We need to use dma_mapping_error() to check the dma address returned
by dma_map_single/page(). Otherwise we would get warning like this:
WARNING: at lib/dma-debug.c:1140
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196
task: c0834300 ti: effe6000 task.ti: c0874000
NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4
REGS: effe7d70 TRAP: 0700 Not tainted (3.18.0-rc2-next-20141029)
MSR: 00021000 <CE,ME> CR: 22044022 XER: 20000000
GPR00: c02b2c98 effe7e20 c0834300 00000098 00021000 00000000 c030b898 00000003
GPR08: 00000001 00000000 00000001 749eec9d 22044022 1001abe0 00000020 ef278678
GPR16: ef278670 ef278668 ef278660 070a8040 c087f99c c08cdc60 00029000 c0840d44
GPR24: c08be6e8 c0840000 effe7e78 ef041340 00000600 ef114e10 00000000 c08be6e0
NIP [c02b2c98] check_unmap+0x51c/0x9e4
LR [c02b2c98] check_unmap+0x51c/0x9e4
Call Trace:
[effe7e20] [c02b2c98] check_unmap+0x51c/0x9e4 (unreliable)
[effe7e70] [c02b31d8] debug_dma_unmap_page+0x78/0x8c
[effe7ed0] [c03d1640] gfar_clean_rx_ring+0x208/0x488
[effe7f40] [c03d1a9c] gfar_poll_rx_sq+0x3c/0xa8
[effe7f60] [c04f8714] net_rx_action+0xc0/0x178
[effe7f90] [c00435a0] __do_softirq+0x100/0x1fc
[effe7fe0] [c0043958] irq_exit+0xa4/0xc8
[effe7ff0] [c000d14c] call_do_irq+0x24/0x3c
[c0875e90] [c00048a0] do_IRQ+0x8c/0xf8
[c0875eb0] [c000ed10] ret_from_except+0x0/0x18
For TX, we need to unmap the pages which has already been mapped and
free the skb before return.
For RX, move the dma mapping and error check to gfar_new_skb(). We
would reuse the original skb in the rx ring when either allocating
skb failure or dma mapping error.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can automatically generate pause frames when the number
of free buffers drops under a certain threshold, but in order to do this,
the address of the last free buffer needs to be written to a specific
register for each RX queue.
This has to be done in 'gfar_clean_rx_ring' which is called for each
RX queue. In order not to impact performance, by adding a register write
for each incoming packet, this operation is done only when the PAUSE frame
transmission is enabled.
Whenever the link is readjusted, this capability is turned on or off.
Signed-off-by: Matei Pavaluca <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local flow control options needed in order to resolve the negotiation
are incorrectly calculated.
Previously 'mii_advertise_flowctrl' was called to determine the local advertising
options, but these were determined based on FLOW_CTRL_RX/TX flags which are
never set through ethtool.
The patch simply translates from ethtool flow options to mii flow options.
Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy device supports 802.3x flow control, but the specific flags are not set
in the phy initialisation code. Flow control flags need to be added to the
supported capabilities of the phydev by the driver.
This is needed in order for ethtool to work ('ethtool -A' code checks for these
flags)
Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each Rx frame the eTSEC writes its FCS (Frame Check Sequence)
to the Rx buffer.
The eTSEC h/w manual states in the "Receive Buffer Descriptor Field
Descriptions" table:
"Data length is the number of octets written by the eTSEC into this BD's
data buffer if L is cleared (the value is equal to MRBLR), or, if L is
set, the length of the frame including *CRC*, FCB (if RCTRL[PRSDEP > 00),
preamble (if MACCFG2[PreAmRxEn]=1), time stamp (if RCTRL[TS] = 1) and
any padding (RCTRL[PAL])."
Though the FCS bytes are removed by the driver before passing the skb
to the net stack, the Rx buffer size computation does not currently
take into account the FCS bytes (4 bytes).
Because the Rx buffer size is multiple of 512 bytes, leaving out the
FCS is not a problem for the default MTU of 1500, as the Rx buffer size
is 1536 in this case. However, for custom MTUs, where the difference
between the MTU size and the Rx buffer size is less, this can be a
problem as the computed Rx buffer size won't be enough to accomodate
the FCS for a received frame that is big enough (close to MTU size).
In such case the received frame is considered to be incomplete (L flag
not set in the RxBD status) and silently dropped.
Note that the driver does not currently support S/G on Rx, so it has to
compute its Rx buffer size based on the MTU of the device.
Reported-by: Kristian Otnes <kotnes@cisco.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace PPC specific eieio() with arch independent wmb()
for other architectures, i.e. ARM.
The eieio() macro is not defined on ARM and generates
build error.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use arch independent code to replace the powerpc dependent
spin_event_timeout() from gfar_halt_nodisable().
Added GRS/GTS read accessors to clean-up the implementation
of gfar_halt_nodisable().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the 32-bit memory access that is not endian safe,
i.e. not giving the desired byte layout for a LE CPU:
tempval = *((u32 *) (tmpbuf + 4)), where 'char tmpbuf[]'.
Get rid of rendundant local vars (tmpbuf[] and idx) and
forced casts. Cleanup comments.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This excludes the PPC specific instructions for PPC based SoC
(MPC85xx family) version identification from ARM builds.
The PPC specific macro mfspr() from asm/reg.h is not defined
by the ARM architecture.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include linux/of_address.h for of_iomap() and linux/of_irq.h
for irq_of_parse_and_map().
This wasn't an issue for PPC, because these were implicitly
included from asm/prom.h (via linux/of.h) for PPC builds only.
ARM builds need these includes explicitly.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The line before the changed if condition is:
priv->phy_node = of_parse_phandle(np, "phy-handle", 0);
. If this call succeeds priv->phy_node must not be overwritten in the if
block; otherwise the reference to the node returned by of_parse_phandle
is lost. So add a check that the if block isn't executed in this case.
Furthermore in the fixed phy case no reference is aquired for phy_node
resulting in an of_node_put without holding a reference. To fix that,
get a reference on the MAC dt node.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put is a noop when being called with NULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().
Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."
So call netif_carrier_off() prior to register_netdev().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with CONFIG_DEBUG_SECTION_MISMATCH enabled, the following
WARNING is occured:
LD drivers/net/built-in.o
WARNING: drivers/net/built-in.o(.text+0xcd4c): Section mismatch in
reference from the function gfar_probe() to the function
.init.text:gfar_init_addr_hash_table()
The function gfar_probe() references
the function __init gfar_init_addr_hash_table().
This is often because gfar_probe lacks a __init
annotation or the annotation of gfar_init_addr_hash_table is wrong.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For phy devices that don't issue interrupts upon link
state changes, phylib polls the link state resulting in
repeated calls to adjust_link(), even if the link state
didn't change. As a result, some mac registers are
repeatedly read and written with the same values, which
is not ok.
To fix this, adjust_link() has been refactored to check
first whether the link state has changed and to take action
only if needed, updating mac registers and local state
variables. The 'new_state' local flag, set if one of the
link params changed (link, speed or duplex), has been
rendered useless and removed by this refactoring.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The P1010 device tree restricts the number of
supported interrupt groups to 1, although the eth
controller can support 2 interrupt groups and the
driver assumes the Multi-Group mode ("fsl,etsec2" model).
So, in this case the assumption that the Multi-Group
mode (MQ_MG_MODE) devices always support 2 interrupt
groups is false. To fix this, a check for the actual
number of interrupt groups enabled in the board's
device tree has been added in gfar_probe for the
"fsl,etsec2" devices.
Without this fix, P1010 based boards claim support for
2 Tx queues to the net stack but only one is actually
allocated, leading to NULL access in xmit. This issue
was introduced by enabling Single-Queue polling for
the P1010 devices.
(71ff9e3 gianfar: Use Single-Queue polling for
"fsl,etsec2")
Fixes: 71ff9e3df7
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts. For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is not instantiated at gfar_of_init() time, when
parsing the DT for info on supported HW queues. Before
the netdev can be allocated, the number of supported
queues must be known. Because the number of supported
queues depends on device type, move the compatibility
checks before netdev allocation. Local vars are used
to hold the operation mode info before netdev allocation.
This fixes the null accesses for priv->.., in gfar_of_init.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the "fsl,etsec2" compatible models the driver currently
supports 8 Tx and Rx DMA rings (aka HW queues). However, there
are only 2 pairs of Rx/Tx interrupt lines, as these controllers
are integrated in low power SoCs with 2 CPUs at most. As a result,
there are at most 2 NAPI instances that have to service multiple
Tx and Rx queues for these devices. This complicates the NAPI
polling routine having to iterate over the mutiple Rx/Tx queues
hooked to the same interrupt lines. And there's also an overhead
at HW level, as the controller needs to service all the 8 Tx rings
in a round robin manner. The combined overhead shows up for multi
parallel Tx flows transmitted by the kernel stack, when the driver
usually starts returning NETDEV_TX_BUSY leading to NETDEV WATCHDOG
Tx timeout triggering if the Tx path is congested for too long.
As an alternative, this patch makes the driver support only one
Tx/Rx DMA ring per NAPI instance (per interrupt group or pair
of Tx/Rx interrupt lines) by default. The simplified single queue
polling routine (gfar_poll_sq) will be the default napi poll routine
for the etsec2 devices too. Some adjustments needed to be made to
link the Tx/Rx HW queues with each NAPI instance (2 in this case).
The gfar_poll_sq() is already successfully used by older SQ_SG_MODE
(single interrupt group) controllers.
This patch fixes Tx timeout triggering under heavy Tx traffic load
(i.e. iperf -c -P 8) for the "fsl,etsec2" (currently the only
MQ_MG_MODE devices). There's also a significant memory footprint
reduction by supporting 2 Rx/Tx DMA rings (at most), instead of 8,
for these devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some concurrency issues on devices w/ 2 CPUs related
to the handling of Rx and Tx interrupts. eTSEC has separate
interrupt lines for Rx and Tx but a single imask register
to mask these interrupts and a single NAPI instance to handle
both Rx and Tx work. As a result, the Rx and Tx ISRs are
identical, both are invoking gfar_schedule_cleanup(), however
both handlers can be entered at the same time when the Rx and
Tx interrupts are taken by different CPUs. In this case
spurrious interrupts (SPU) show up (in /proc/interrupts)
indicating a concurrency issue. Also, Tx overruns followed
by Tx timeout have been observed under heavy Tx traffic load.
To address these issues, the schedule cleanup ISR part has
been changed to handle the Rx and Tx interrupts independently.
The patch adds a separate NAPI poll routine for Tx cleanup to
be triggerred independently by the Tx confirmation interrupts
only. Existing poll functions are modified to handle only
the Rx path processing. The Tx poll routine does not need a
budget, since Tx processing doesn't consume NAPI budget, and
hence it is registered with minimum NAPI weight.
NAPI scheduling does not require locking since there are
different NAPI instances between the Rx and Tx confirmation
paths now.
So, the patch fixes the occurence of spurrious Rx/Tx interrupts.
Tx overruns also occur less frequently now.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming the interrupt coalescing (IC) registers while
the controller/DMA is on may incur the loss of one Tx
confirmation interrupt, under certain conditions. This is
a subtle hw race because it does not occur during a burst
of Tx packets. It has been observed on p2020 devices that,
if just one packet is being xmit'ed, the Tx confirmation
doesn't trigger and BQL evetually blocks the Tx queues,
followed by Tx timeout and an un-responsive device.
This issue was not apparent prior to introducing BQL
support, as a late Tx confirmation was not an issue back then
and the next burst of Tx frames would have triggered the
Tx confirmation/ Tx ring cleanup anyway.
Bottom line, the hw specifications state that the IC registers
should not be programmed while the Rx/Tx blocks (the DMA) are
enabled. Further more, these registers are currently re-written
with the same values on the processing path, over and over again.
To fix this, rewriting the IC registers has been removed from
the processing path (napi poll). A complete MAC reset procedure
has been implemented for the ethtool -c option instead, to
reliably update these registers while the controller is stopped.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset procedure, stop_gfar()/startup_gfar(), has
concurrency issues.
"Kernel access of bad area" oopses show up during Tx timeout
device reset or other reset cases (like changing MTU) that
happen while the interface still has traffic. The oopses
happen in start_xmit and clean_tx_ring when accessing tx_queue->
tx_skbuff which is NULL. The race comes from de-allocating the
tx_skbuff while transmission and napi processing are still
active. Though the Tx queues get temoprarily stopped when Tx
timeout occurs, they get re-enabled as a result of Tx congestion
handling inside the napi context (see clean_tx_ring()). Not
disabling the napi during reset is also a bug, because
clean_tx_ring() will try to access tx_skbuff while it is being
de-alloc'ed and re-alloc'ed.
To fix this, stop_gfar() needs to disable napi processing
after stopping the Tx queues. However, in order to prevent
clean_tx_ring() to re-enable the Tx queue before the napi
gets disabled, the device state DOWN has been introduced.
It prevents the Tx congestion management from re-enabling the
de-congested Tx queue while the device is brought down.
An additional locking state, RESETTING, has been introduced
to prevent simultaneous resets or to prevent configuring the
device while it is resetting.
The bogus 'rxlock's (for each Rx queue) have been removed since
their purpose is not justified, as they don't prevent nor are
suited to prevent device reset/reconfig races (such as this one).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the device (stop_gfar()/startup_gfar()) should
be fast and to the point, in order to timely recover
from an error condition (like Tx timeout) or during
device reconfig. The irq free/ request routines are just
redundant here, and they should be part of the device
close/ open routines instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RCTRL and TCTRL registers should not be changed
on-the-fly, while the controller is running, otherwise
unexpected behaviour occurs. But that's exactly what
gfar_vlan_mode() does, updating the VLAN acceleration
bits inside RCTRL/TCTRL. The attempt to lock these
operations doesn't help, but only adds to the confusion.
There's also a dependency for Rx FCB insertion (activating
/de-activating the TOE offload block on Rx) which might
change the required rx buffer size. This makes matters
worse as gfar_vlan_mode() ends up calling gfar_change_mtu(),
though the MTU size remains the same. Note that there are
other situations that may affect the required rx buffer size,
like changing RXCSUM or rx hw timestamping, but errorneously
the rx buffer size is not recomputed/ updated in the process.
To fix this, do the vlan updates properly inside the MAC
reset and reconfiguration procedure, which takes care of
the rx buffer size dependecy and the rx TOE block (PRSDEP)
activation/deactivation as well (in the correct order).
As a consequence, MTU/ rx buff size updates are done now
by the same MAC reset and reconfig procedure, so that out
of context updates to MAXFRM, MRBLR, and MACCFG inside
change_mtu() are no longer needed. The rx buffer size
dependecy to Rx FCB is now handled for the other cases too
(RXCSUM and rx hw timestamping).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main MAC config registers like: RCTRL/TCTRL, MRBLR,
MAXFRM, RXIC/TXIC, most fields of MACCFG1/2, should not
be changed on-the-fly, but at least after stopping the
DMA and disabling the Rx/Tx blocks and, for increased
reliability, after a MAC soft reset.
Impelement a complete MAC soft reset and reconfig procedure
following the latest HW advisories - gfar_mac_reset() - to
replace gfar_mac_init() and (the confusing) init_registers()
functions.
Factor out separate config functions for RCTRL and TCTRL,
insure programming order of the relevant config regs after
MAC soft reset.
Split gfar_hw_init() into gfar_mac_reset() and the remaining
global regs that don't need to be reconfigured after MAC soft
reset (FIFOCFG, ATTRELI, HW counters a.s.o).
As gfar_hw_init() now makes all the register writes @probe()
time, based on all the device flags and config options, it
must be moved further down, just before register_netdev(),
as the last config step when the config values are comitted
to HW. Also, move netif_carrier_off() after register_netdev(),
because it has no effect if called before.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_halt() and gfar_start() are responsible for stopping
and starting the DMA and the Rx/Tx hw rings. They implement
the support for the "graceful Rx/Tx stop/start" hw procedure,
and also disable/enable eTSEC's hw interrupts in the process.
The GRS/GTS procedure requires however to have the RQUEUE/TQUEUE
registers cleared first and to wait for a period of time for the
current frame to pass through the interface (around ~10ms for a
jumbo frame). Only then may the GTS and GRS bits from DMACTRL be
set to shut down the DMA, and finally the Tx_EN and Rx_EN bits in
MACCFG1 may be cleared to disable the Tx/Rx blocks.
The same register programming order applies to start the Rx/Tx:
enabling the RQUEUE/TQUEUE *before* clearing the GRS/GTS bits.
This is a HW recommendation in order to avoid a possible
controller "lock up" during graceful reset.
Cleanup the gfar_halt()/start() prototypes, to take priv instead
of ndev as their purpose is to operate on HW. Enabling the
RQUEUE/TQUEUE in the hw_init() is not needed anymore since
that's the job of gfar_start().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
