Add set/show support for the ENABLE_ROCE NVM parameter to
enable/disable RoCE for a PF.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Co-developed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250310183129.3154117-4-michael.chan@broadcom.com
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This reverts:
commit 02acd39953 ("bnxt_en: parse result field when NVRAM package install fails")
commit 22f5dba506 ("bnxt_en: add an nvm test for hw diagnose")
commit bafed3f231 ("bnxt_en: implement hw health reporter")
These patches are still under discussion / I don't think they
are right, and since the authors don't reply promptly let me
lessen my load of "things I need to resolve before next release"
and revert them.
Acked-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220308173659.304915-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reporter will report NVM errors which are non-fatal.
When we receive these NVM error events, we'll report it
through this new hw health reporter.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health reporter state should be maintained over resets. Previously
reporters were destroyed if the device capabilities changed, but
since none of the reporters depend on capabilities anymore, this
logic should be removed.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware resets initiated by the user are not errors and should not
be reported via devlink. Once only unsolicited resets remain, it is no
longer sensible to maintain a separate fw_reset reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reported parameter value should not take into account the state
of remote drivers. Firmware will reject remote resets as appropriate,
thus it is not strictly necessary to check HOT_RESET_ALLOWED before
attempting to initiate a reset. But we add the check so that we can
provide more intuitive messages when reset is not permitted.
This firmware setting needs to be restored from all functions after
a firmware reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to reload driver_reinit, the RTNL lock is held across reload
down and up to prevent interleaving state changes. But we need to
subsequently release the RTNL lock while waiting for firmware reset
to complete.
Also keep a statistic on fw_activate resets initiated remotely from
other functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink is a software interface that doesn't depend on any hardware
capabilities. The failure in SW means memory issues, wrong parameters,
programmer error e.t.c.
Like any other such interface in the kernel, the returned status of
devlink APIs should be checked and propagated further and not ignored.
Fixes: 4ab0c6a8ff ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
P5 devices store NVM arrays using a different internal representation.
This implementation detail permeates into the HWRM API, requiring the
caller to explicitly index the array elements in HWRM_NVM_GET_VARIABLE
on these devices. Conversely, older devices do not support the indexed
mode of operation and require reading the raw NVM content.
Fixes: db28b6c77f ("bnxt_en: Fix devlink info's stored fw.psid version format.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_dl_info_put() to simplify the code, as there
are more stored firmware version fields to be added in the next patch.
Also, rename fw_ver variable name to ncsi_ver for better naming while
copying to devlink info_get cb.
v2:
Ensure active_pkg_name string is NULL terminated when copied to
devlink.
Return directly from the last call to bnxt_dl_info_put().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-9-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Broadcom adapters support only maximum of 512 CQs per PF. If user sets
MSIx vectors more than supported CQs, firmware is setting incorrect value
for msix_vec_per_pf_max parameter. Fix it by reducing the BNXT_MSIX_VEC_MAX
value to 512, even though the maximum # of MSIx vectors supported by adapter
are 1280.
Fixes: f399e84978 ("bnxt_en: Use msix_vec_per_pf_max and msix_vec_per_pf_min devlink params.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the following information via devlink info command:
- Driver name
- Board id
- Broad revision
- Board Serial number
- Board FW version
- FW parameter set version
- FW App version
- FW management version
- FW RoCE version
Standard output example:
$ devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver bnxt_en
serial_number 00-10-18-FF-FE-AD-05-00
versions:
fixed:
asic.id D802
asic.rev 1
running:
fw 216.1.124.0
fw.psid 0.0.0
fw.app 216.1.122.0
fw.mgmt 864.0.32.0
fw.roce 216.1.15.0
[ This version has incorporated changes suggested by Jakub Kicinski to
use generic devlink version tags. ]
v2: Use fw.psid
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return EINPROGRESS to devlink health reporter recover as we are not yet
done and call devlink_health_reporter_recovery_done once reset is
successfully completed from workqueue context.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the logic to properly check the fw capabilities and create the
devlink health reporters only when needed. The current code creates
the reporters unconditionally as long as bp->fw_health is valid, and
that's not correct.
Call bnxt_dl_fw_reporters_create() directly from the init and reset
code path instead of from bnxt_dl_register(). This allows the
reporters to be adjusted when capabilities change. The same
applies to bnxt_dl_fw_reporters_destroy().
Fixes: 6763c779c2 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code that rounds up the NVRAM parameter bit size to the next
byte size for the devlink parameter is not always correct. The MSIX
devlink parameters are 4 bytes and we don't get the correct size
using this method.
Fix it by adding a new dl_num_bytes member to the bnxt_dl_nvm_param
structure which statically provides bytesize information according
to the devlink parameter type definition.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial port params table and register it")
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add devlink health reporter for the firmware reset event. Once we get
the notification from firmware about the impending reset, the driver
will report this to devlink and the call to bnxt_fw_reset() will be
initiated to complete the reset sequence.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds following driver-specific permanent mode boolean
parameter.
gre_ver_check - Generic Routing Encapsulation(GRE) version check
will be enabled in the device. If disabled, device skips version
checking for GRE packets.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for following generic permanent mode
devlink parameters. They can be modified using devlink param
commands.
msix_vec_per_pf_max - This param sets the number of MSIX vectors
that the device requests from the host on driver initialization.
This value is set in the device which limits MSIX vectors per PF.
msix_vec_per_pf_min - This param sets the number of minimal MSIX
vectors required for the device initialization. Value 0 indicates
a default value is selected. This value is set in the device which
limits MSIX vectors per PF.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ignore_ari generic permanent mode
devlink parameter. This parameter is disabled by default. It can be
enabled using devlink param commands.
ignore_ari - If enabled, device ignores ARI(Alternate Routing ID)
capability, even when platforms has the support and creates same number
of partitions when platform does not support ARI capability.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create initial devlink parameters table for bnxt_en.
Table consists of a permanent generic parameter.
enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving generic devlink code (registration) out of VF-R code
into new bnxt_devlink file, in preparation for future work
to add additional devlink functionality to bnxt.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
