Downgrade the "msg lost in rx" message to debug level, to prevent
flooding the kernel log with error messages.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250711-mcan_ratelimit-v3-1-7413e8e21b84@geanix.com
[mkl: enhance commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch for the introduction of CAN XL.
CAN FD and CAN XL uses similar bittiming parameters. Add one level of
nesting for all the CAN FD parameters. Typically:
priv->can.data_bittiming;
becomes:
priv->can.fd.data_bittiming;
This way, the CAN XL equivalent (to be introduced later) would be:
priv->can.xl.data_bittiming;
Add the new struct data_bittiming_params which contains all the data
bittiming parameters, including the TDC and the callback functions.
This done, update all the CAN FD drivers to make use of the new
layout.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250501171213.2161572-2-mailhol.vincent@wanadoo.fr
[mkl: fix rcar_canfd]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 1be37d3b04 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/all/f1a87fcba211f6ce262a2d23fd152185f452c32d.1738746872.git.namcao@linutronix.de
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEUEC6huC2BN0pvD5fKDiiPnotvG8FAmeA/ocTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAoOKI+ei28b7FlB/9c3ThnLVI/eezSZGE2UpvjN3eZWemk
UkTxypJ9NpJkd1UovpOGVTNjAmlN+6+yjATJm8GBpSg99cN5Y8gcu7lWnsnidopm
mkUNE+ZPPmkxe/ay1d6BfqJKzZTqkdJ6w1QlIXFfDgbRr4YaX9bn3egdtoNhq4fR
0qRt6++7V3hhhlr3x0hrhB+3nrTkL8eVBVWNEKFPCnCn9E3p7izXwZAG/y/IC4sP
swTk1BbSZg9ajds/1DE2AVeUvqz63FnzjY7YChU5WdNY5bq/cFHGoCWn8aZEX/kC
YFrQC3lonlNa/A5IFfb32HaFT0qFFbOKBHXru/wFuuwJCKVLUKsmLsd/
=c3SH
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.14-20250110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-01-10
Pierre-Henry Moussay adds PIC64GX compatibility to the DT bindings for
Microchip's mpfs-can IP core.
The next 3 patches are by Sean Nyekjaer and target the tcan4x5x
driver. First the DT bindings is converted to DT schema, then nWKRQ
voltage selection is added to the driver.
Dario Binacchi's patch for the sun4i_can makes the driver more
consistent by adding a likely() to the driver.
Another patch by Sean Nyekjaer for the tcan4x5x driver gets rid of a
false error message.
Charan Pedumuru converts the atmel-can DT bindings to DT schema.
The next 2 patches are by Oliver Hartkopp. The first one maps Oliver's
former mail addresses to a dedicated CAN mail address. The second one
assigns net/sched/em_canid.c additionally to the CAN maintainers.
Ariel Otilibili's patch removes dead code from the CAN dev helper.
The next 3 patches are by Sean Nyekjaer and add HW standby support to
the tcan4x5x driver.
A patch by Dario Binacchi fixes the DT bindings for the st,stm32-bxcan
driver.
The last 4 patches are by Jimmy Assarsson and target the kvaser_usb
and the kvaser_pciefd driver: error statistics are improved and
CAN_CTRLMODE_BERR_REPORTING is added.
* tag 'linux-can-next-for-6.14-20250110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: kvaser_pciefd: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_pciefd: Update stats and state even if alloc_can_err_skb() fails
can: kvaser_usb: Add support for CAN_CTRLMODE_BERR_REPORTING
can: kvaser_usb: Update stats and state even if alloc_can_err_skb() fails
dt-bindings: can: st,stm32-bxcan: fix st,gcan property type
can: m_can: call deinit/init callback when going into suspend/resume
can: tcan4x5x: add deinit callback to set standby mode
can: m_can: add deinit callback
can: dev: can_get_state_str(): Remove dead code
MAINTAINERS: assign em_canid.c additionally to CAN maintainers
mailmap: add an entry for Oliver Hartkopp
dt-bindings: net: can: atmel: Convert to json schema
can: tcan4x5x: get rid of false clock errors
can: sun4i_can: continue to use likely() to check skb
can: tcan4x5x: add option for selecting nWKRQ voltage
dt-bindings: can: tcan4x5x: Document the ti,nwkrq-voltage-vio option
dt-bindings: can: convert tcan4x5x.txt to DT schema
dt-bindings: can: mpfs: add PIC64GX CAN compatibility
====================
Link: https://patch.msgid.link/20250110112712.3214173-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is added in preparation for calling standby mode in the tcan4x5x
driver or other users of m_can.
For the tcan4x5x; If Vsup 12V, standby mode will save 7-8mA, when the
interface is down.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20241122-tcan-standby-v3-1-90bafaf5eccd@geanix.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The interrupt line of PCI devices is interpreted as edge-triggered,
however the interrupt signal of the m_can controller integrated in Intel
Elkhart Lake CPUs appears to be generated level-triggered.
Consider the following sequence of events:
- IR register is read, interrupt X is set
- A new interrupt Y is triggered in the m_can controller
- IR register is written to acknowledge interrupt X. Y remains set in IR
As at no point in this sequence no interrupt flag is set in IR, the
m_can interrupt line will never become deasserted, and no edge will ever
be observed to trigger another run of the ISR. This was observed to
result in the TX queue of the EHL m_can to get stuck under high load,
because frames were queued to the hardware in m_can_start_xmit(), but
m_can_finish_tx() was never run to account for their successful
transmission.
On an Elkhart Lake based board with the two CAN interfaces connected to
each other, the following script can reproduce the issue:
ip link set can0 up type can bitrate 1000000
ip link set can1 up type can bitrate 1000000
cangen can0 -g 2 -I 000 -L 8 &
cangen can0 -g 2 -I 001 -L 8 &
cangen can0 -g 2 -I 002 -L 8 &
cangen can0 -g 2 -I 003 -L 8 &
cangen can0 -g 2 -I 004 -L 8 &
cangen can0 -g 2 -I 005 -L 8 &
cangen can0 -g 2 -I 006 -L 8 &
cangen can0 -g 2 -I 007 -L 8 &
cangen can1 -g 2 -I 100 -L 8 &
cangen can1 -g 2 -I 101 -L 8 &
cangen can1 -g 2 -I 102 -L 8 &
cangen can1 -g 2 -I 103 -L 8 &
cangen can1 -g 2 -I 104 -L 8 &
cangen can1 -g 2 -I 105 -L 8 &
cangen can1 -g 2 -I 106 -L 8 &
cangen can1 -g 2 -I 107 -L 8 &
stress-ng --matrix 0 &
To fix the issue, repeatedly read and acknowledge interrupts at the
start of the ISR until no interrupt flags are set, so the next incoming
interrupt will also result in an edge on the interrupt line.
While we have received a report that even with this patch, the TX queue
can become stuck under certain (currently unknown) circumstances on the
Elkhart Lake, this patch completely fixes the issue with the above
reproducer, and it is unclear whether the remaining issue has a similar
cause at all.
Fixes: cab7ffc032 ("can: m_can: add PCI glue driver for Intel Elkhart Lake")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/fdf0439c51bcb3a46c21e9fb21c7f1d06363be84.1728288535.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While an m_can controller usually already has the init flag from a
hardware reset, no such reset happens on the integrated m_can_pci of the
Intel Elkhart Lake. If the CAN controller is found in an active state,
m_can_dev_setup() would fail because m_can_niso_supported() calls
m_can_cccr_update_bits(), which refuses to modify any other configuration
bits when CCCR_INIT is not set.
To avoid this issue, set CCCR_INIT before attempting to modify any other
configuration flags.
Fixes: cd5a46ce6f ("can: m_can: don't enable transceiver when probing")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/e247f331cb72829fcbdfda74f31a59cbad1a6006.1728288535.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The m_can_handle_lec_err() function was incorrectly incrementing only the
receive error counter, even in cases of bit or acknowledgment errors that
occur during transmission.
Fix the issue by incrementing the appropriate counter based on the
type of error.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit b382380c0d ("can: m_can: Add hrtimer to generate software
interrupt") support for IRQ-less devices was added. Instead of an
interrupt, the interrupt routine is called by a hrtimer-based polling
loop.
That patch forgot to change free_irq() to be only called for devices
with IRQs. Fix this, by calling free_irq() conditionally only if an
IRQ is available for the device (and thus has been requested
previously).
Fixes: b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20240930-m_can-cleanups-v1-1-001c579cdee4@pengutronix.de
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After calling m_can_stop() an interrupt may be pending or NAPI might
still be executed. This means the driver might still touch registers
of the IP core after the clocks have been disabled. This is not good
practice and might lead to aborts depending on the SoC integration.
To avoid these potential problems, make m_can_close() symmetric to
m_can_open(), i.e. stop the clocks at the end, right before shutting
down the transceiver.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-2-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If an interrupt (RX-complete or error flag) is set when bringing up
the CAN device, e.g. due to CAN bus traffic before initializing the
device, when m_can_start() is called and interrupts are enabled,
m_can_isr() is called immediately, which disables all CAN interrupts
and calls napi_schedule().
Because napi_enable() isn't called until later in m_can_open(), the
call to napi_schedule() never schedules the m_can_poll() callback and
the device is left with interrupts disabled and can't receive any CAN
packets until rebooted.
This can be verified by running "cansend" from another device before
setting the bitrate and calling "ip link set up can0" on the test
device. Adding debug lines to m_can_isr() shows it's called with flags
(IR_EP | IR_EW | IR_CRCE), which calls m_can_disable_all_interrupts()
and napi_schedule(), and then m_can_poll() is never called.
Move the call to napi_enable() above the call to m_can_start() to
enable any initial interrupt flags to be handled by m_can_poll() so
that interrupts are reenabled. Add a call to napi_disable() in the
error handling section of m_can_open(), to handle the case where later
functions return errors.
Also, in m_can_close(), move the call to napi_disable() below the call
to m_can_stop() to ensure all interrupts are handled when bringing
down the device. This race condition is much less likely to occur.
Tested on a Microchip SAMA7G54 MPU. The fix should be applicable to
any SoC with a Bosch M_CAN controller.
Signed-off-by: Jake Hamby <Jake.Hamby@Teledyne.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-1-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The use of coalescing for non-peripheral chips in the current
implementation is limited to non-existing. Disable the possibility to
set coalescing through ethtool.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-8-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To force writing the enabled interrupts, reset the active_interrupts
cache.
Fixes: 07f25091ca ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-7-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
active_interrupts is a cache for the enabled interrupts and not the
global masking of interrupts. Do not clear this variable otherwise we
may loose the state of the interrupts.
Fixes: 07f25091ca ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On setups without interrupts, the interrupt handler is called from a
timer callback. For non-peripheral receives napi is scheduled,
interrupts are disabled and the timer is canceled with a blocking call.
In case of an error this can happen as well.
Check if napi is scheduled in the timer callback after the interrupt
handler executed. If napi is scheduled, the timer is disabled. It will
be reenabled by m_can_poll().
Return error values from the interrupt handler so that interrupt threads
and timer callback can deal differently with it. In case of the timer
we only disable the timer. The rest will be done when stopping the
interface.
Fixes: b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
Fixes: a163c57610 ("can: m_can: Start/Cancel polling timer together with interrupts")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_rx_peripheral() is a wrapper around m_can_rx_handler() that calls
m_can_disable_all_interrupts() on error. The same handling for the same
error path is done in m_can_isr() as well.
So remove m_can_rx_peripheral() and do the call from m_can_isr()
directly.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We don't need to disable coalescing when the interrupt handler executes
while the chip is suspended. The coalescing is already reset during
suspend.
Fixes: 07f25091ca ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During resume the interrupts are limited to IR_RF0N and the chip keeps
running. In this case if coalescing is enabled and active we may miss
waterlevel interrupts during suspend. It is safer to reset the
coalescing by stopping the timer and adding IR_RF0N | IR_TEFN to the
interrupts.
This is a theoratical issue and probably extremely rare.
Cc: Martin Hundebøll <martin@geanix.com>
Fixes: 4a94d7e31c ("can: m_can: allow keeping the transceiver running in suspend")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240805183047.305630-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It appears that the irq requested in m_can_open() may be leaked
if an error subsequently occurs: if m_can_start() fails.
Address this by calling free_irq in the unwind path for
such cases.
Flagged by Smatch.
Compile tested only.
Fixes: eaacfeaca7 ("can: m_can: Call the RAM init directly from m_can_chip_config")
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240805-mcan-irq-v2-1-7154c0484819@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The m_can driver sets and clears the CCCR.INIT bit during probe (both
when testing the NON-ISO bit, and when configuring the chip). After
clearing the CCCR.INIT bit, the transceiver enters normal mode, where it
affects the CAN bus (i.e. it ACKs frames). This can cause troubles when
the m_can node is only used for monitoring the bus, as one cannot setup
listen-only mode before the device is probed.
Rework the probe flow, so that the CCCR.INIT bit is only cleared when
upping the device. First, the tcan4x5x driver is changed to stay in
standby mode during/after probe. This in turn requires changes when
setting bits in the CCCR register, as its CSR and CSA bits are always
high in standby mode.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240607105210.155435-1-martin@geanix.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a flag to the device class structure that leaves the chip in a
running state with rx interrupt enabled, so that an m_can device driver
can configure and use the interrupt as a wakeup source.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_clk_start() already skip starting the clock when
clock support is disabled, remove the redundant check in
m_can_class_register().
This also solves the imbalance with m_can_clk_stop() that is called
afterward in the same function before the return.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240104235723.46931-1-francesco@dolcini.it
[mkl: rebased to net-next/main]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can supports submitting multiple transmits with one register write.
This is an interesting option to reduce the number of SPI transfers for
peripheral chips.
The m_can_tx_op is extended with a bool that signals if it is the last
transmission and the submit should be executed immediately.
The worker then writes the skb to the FIFO and submits it only if the
submit bool is set. If it isn't set, the worker will write the next skb
which is waiting in the workqueue to the FIFO, etc.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-15-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The network queue is currently always stopped in start_xmit and
continued in the interrupt handler. This is not possible anymore if we
want to keep multiple transmits in flight in parallel.
Use the previously introduced tx_fifo_in_flight counter to control the
network queue instead. This has the benefit of not needing to ask the
hardware about fifo status.
This patch stops the network queue in start_xmit if the number of
transmits in flight reaches the size of the fifo and wakes up the queue
from the interrupt handler once the transmits in flight drops below the
fifo size. This means any skbs over the limit will be rejected
immediately in start_xmit (it shouldn't be possible at all to reach that
state anyways).
The maximum number of transmits in flight is the size of the fifo.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-13-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Keep track of the number of transmits in flight.
This patch prepares the driver to control the network interface queue
based on this counter. By itself this counter be
implemented with an atomic, but as we need to do other things in the
critical sections later I am using a spinlock instead.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-12-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current implementation uses the workqueue for peripheral chips to
submit work. Only a single work item is queued and used at any time.
To be able to keep more than one transmit in flight at a time, prepare
the workqueue to support multiple transmits at the same time.
Each work item now has a separate storage for a skb and a pointer to
cdev. This assures that each workitem can be processed individually.
The workqueue is replaced by an ordered workqueue which makes sure that
only a single worker processes the items queued on the workqueue. Also
items are ordered by the order they were enqueued. This removes most of
the concurrency the workqueue normally offers. It is not necessary for
this driver.
The cleanup functions have to be adopted a bit to handle this new
mechanism.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-11-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_tx_handler is the only place where data is written to the tx fifo.
We can calculate the putidx in the driver code here to avoid the
dependency on the txfqs register.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-10-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
putidx is not an integer normally, it is an unsigned field used in
hardware registers. Use a u32 for it.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-9-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add TX support to get/set functions for ethtool coalescing.
tx-frames-irq and tx-usecs-irq can only be set/unset together.
tx-frames-irq needs to be less than TXE and TXB.
As rx and tx share the same timer, rx-usecs-irq and tx-usecs-irq can be
enabled/disabled individually but they need to have the same value if
enabled.
Polling is excluded from TX irq coalescing.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-8-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the possibility to set coalescing parameters with ethtool.
rx-frames-irq and rx-usecs-irq can only be set and unset together as the
implemented mechanism would not work otherwise. rx-frames-irq can't be
greater than the RX FIFO size.
Also all values can only be changed if the chip is not active.
Polling is excluded from irq coalescing support.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-7-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Extend the coalescing implementation for transmits.
In normal mode the chip raises an interrupt for every finished transmit.
This implementation switches to coalescing mode as soon as an interrupt
handled a transmit. For coalescing the watermark level interrupt is used
to interrupt exactly after x frames were sent. It switches back into
normal mode once there was an interrupt with no finished transmit and
the timer being inactive.
The timer is shared with receive coalescing. The time for receive and
transmit coalescing timers have to be the same for that to work. The
benefit is to have only a single running timer.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can offers the possibility to set an interrupt on reaching a watermark
level in the receive FIFO. This can be used to implement coalescing.
Unfortunately there is no hardware timeout available to trigger an
interrupt if only a few messages were received within a given time. To
solve this I am using a hrtimer to wake up the irq thread after x
microseconds.
The timer is always started if receive coalescing is enabled and new
received frames were available during an interrupt. The timer is stopped
if during a interrupt handling no new data was available.
If the timer is started the new item interrupt is disabled and the
watermark interrupt takes over. If the timer is not started again, the
new item interrupt is enabled again, notifying the handler about every
new item received.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Combine header and data before writing to the transmit fifo to reduce
the overhead for peripheral chips.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hrtimer_init() is called in m_can_plat_probe() and the hrtimer
function is set in m_can_class_register(). For readability it is better
to keep these two together in m_can_class_register().
Cc: Judith Mendez <jm@ti.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Interrupts are enabled/disabled in more places than just m_can_start()
and m_can_stop(). Couple the polling timer with enabling/disabling of
all interrupts to achieve equivalent behavior.
Cc: Judith Mendez <jm@ti.com>
Fixes: b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To reduce debugging effort in case the mram is misconfigured, add this
size check of the DT configuration. Currently if the mram configuration
doesn't fit into the available MRAM it just overwrites other areas of
the MRAM.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/all/20230728141923.162477-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the rx_offload_get_echo_skb() function to
can_rx_offload_get_echo_skb_queue_timestamp(), since it inserts the
echo skb into the rx-offload queue sorted by timestamp.
This is a preparation for adding
can_rx_offload_get_echo_skb_queue_tail(), which adds the echo skb to
the end of the queue. This is intended for devices that do not support
timestamps.
Link: https://lore.kernel.org/all/20230718-gs_usb-rx-offload-v2-1-716e542d14d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/all/20230724211841.805053-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce timer polling method to MCAN since some SoCs may not
have M_CAN interrupt routed to A53 Linux and do not have
interrupt property in device tree M_CAN node.
On AM62x SoC, MCANs on MCU domain do not have hardware interrupt
routed to A53 Linux, instead they will use timer polling method.
Add an hrtimer to MCAN class device. Each MCAN will have its own
hrtimer instantiated if there is no hardware interrupt found in
device tree M_CAN node. The timer will generate a software
interrupt every 1 ms. In hrtimer callback, we check if there is
a transaction pending by reading a register, then process by
calling the isr if there is.
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Verdin AM62
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/all/20230707204714.62964-3-jm@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch aligns code to match open parenthesis and removes a
trailing whitespace.
Fixes: eb38c2053b ("can: rx-offload: rename can_rx_offload_queue_sorted() -> can_rx_offload_queue_timestamp()")
Fixes: f5071d9e72 ("can: m_can: m_can_handle_bus_errors(): add support for handling DLEC error on CAN-FD frames")
Reported-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/all/20230523062410.1984098-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Interrupts currently get disabled if the interrupt status shows new
received data. Non-peripheral chips handle receiving in a worker thread,
but peripheral chips are handling the receive process in the threaded
interrupt routine itself without scheduling it for a different worker.
So there is no need to disable interrupts for peripheral chips.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are a number of interrupts that are not used by the driver at the
moment. Disable all of these.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Interrupts are enabled a few lines further down as well. Remove this
second call to enable all interrupts.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The code already exits the function on !ir before this condition. No
need to check again if anything is set as IR_ALL_INT is 0xffffffff.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
