This adds SDHCI_AM654_QUIRK_DISABLE_HS400 quirk which shall be used
to disable HS400 support. AM62P SR1.0 and SR1.1 do not support HS400
due to errata i2458 [0] so disable HS400 for these SoC revisions.
[0] https://www.ti.com/lit/er/sprz574a/sprz574a.pdf
Fixes: 37f2816551 ("arm64: dts: ti: k3-am62p: Add ITAP/OTAP values for MMC")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250820193047.4064142-1-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During SD suspend/resume without a full card rescan (when using
non-removable SD cards for rootfs), the SD card initialization may fail
after resume. This occurs because, after a host controller reset, the
card detect logic may take time to stabilize due to debounce logic.
Without waiting for stabilization, the host may attempt powering up the
card prematurely, leading to command timeouts during resume flow.
Add sdhci_arasan_set_power_and_bus_voltage() to wait for the card detect
stable bit before power up the card. Since the stabilization time
is not fixed, a maximum timeout of one second is used to ensure
sufficient wait time for the card detect signal to stabilize.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250730060543.1735971-1-sai.krishna.potthuri@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to a flaw in the hardware design, the GL9763e replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9763e
PCI config. Therefore, the replay timer timeout must be masked.
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Fixes: 1ae1d2d6e5 ("mmc: sdhci-pci-gli: Add Genesys Logic GL9763E support")
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250731065752.450231-4-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to fix replay timer timeout, add
sdhci_gli_mask_replay_timer_timeout() function
to simplify some of the code, allowing it to be re-used.
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Fixes: 1ae1d2d6e5 ("mmc: sdhci-pci-gli: Add Genesys Logic GL9763E support")
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250731065752.450231-2-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Remove redundant pm_runtime_mark_last_busy() calls
MMC host:
- Convert drivers to use devm_mmc_alloc_host()
- Remove redundant pm_runtime_mark_last_busy() calls
- renesas_sdhi: Add support for the RZ/T2H and RZ/N2H variants
- renesas_sdhi: Fix incorrect auto retuning for an SDIO card
- rtsx_usb_sdmmc: Add 74 clocks in poweron flow
- rtsx_usb_sdmmc: Re-work the code in sd_set_power_mode()
- loongson2: Add driver for the Loongson-2K SD/SDIO controller
- loongson2: Add support for the Loongson-2K2000 SD/SDIO/eMMC controller
- sdhci: Drop sdhci_free_host()/sdhci_pltfm_free() interface
- sdhci: Remove the sdhci_free_host() and sdhci_pltfm_free() helpers
- sdhci-cadence: Add support for the Mobileye EyeQ controller
- sdhci-esdhc-imx: Optimize clock loopback selection
- sdhci-esdhc-imx: Don't change pinctrl in suspend if wakeup source
- sdhci-msm: Add support for the Milos variant
- sdhci-msm: Add support for the qcs8300 variant
- sdhci-msm: Ensure SD card power isn't ON when card gets removed
- sdhci-of-k1: Disable HW busy detection
-----BEGIN PGP SIGNATURE-----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=bC9D
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Remove redundant pm_runtime_mark_last_busy() calls
MMC host:
- Convert drivers to use devm_mmc_alloc_host()
- Remove redundant pm_runtime_mark_last_busy() calls
- renesas_sdhi:
- Add support for the RZ/T2H and RZ/N2H variants
- Fix incorrect auto retuning for an SDIO card
- rtsx_usb_sdmmc:
- Add 74 clocks in poweron flow
- Re-work the code in sd_set_power_mode()
- loongson2:
- Add driver for the Loongson-2K SD/SDIO controller
- Add support for the Loongson-2K2000 SD/SDIO/eMMC controller
- sdhci:
- Drop sdhci_free_host()/sdhci_pltfm_free() interface
- Remove the sdhci_free_host() and sdhci_pltfm_free() helpers
- sdhci-cadence: Add support for the Mobileye EyeQ controller
- sdhci-esdhc-imx:
- Optimize clock loopback selection
- Don't change pinctrl in suspend if wakeup source
- sdhci-msm:
- Add support for the Milos variant
- Add support for the qcs8300 variant
- Ensure SD card power isn't ON when card gets removed
- sdhci-of-k1: Disable HW busy detection"
* tag 'mmc-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (102 commits)
mmc: loongson2: Unify the function prefixes for loongson2_mmc_pdata
mmc: loongson2: Fix error code in loongson2_mmc_resource_request()
dt-bindings: mmc: sdhci-msm: document the Milos SDHCI Controller
mmc: loongson2: prevent integer overflow in ret variable
mmc: Remove redundant pm_runtime_mark_last_busy() calls
mmc: sdhci-msm: Ensure SD card power isn't ON when card removed
dt-bindings: mmc: Add sdhci compatible for qcs8300
mmc: sdhci-cadence: use of_property_present
mmc: loongson2: Add Loongson-2K2000 SD/SDIO/eMMC controller driver
dt-bindings: mmc: loongson,ls2k0500-mmc: Add compatible for Loongson-2K2000
mmc: loongson2: Add Loongson-2K SD/SDIO controller driver
dt-bindings: mmc: Add Loongson-2K SD/SDIO/eMMC controller binding
mmc: Convert ternary operator to str_true_false() helper
dt-bindings: mmc: renesas,sdhi: Document RZ/T2H and RZ/N2H support
mmc: sdhci-cadence: add Mobileye eyeQ support
dt-bindings: mmc: cdns: add Mobileye EyeQ MMC/SDHCI controller
mmc: rtsx_usb_sdmmc: Fix clang -Wimplicit-fallthrough in sd_set_power_mode()
mmc: cb710-mmc: Convert ternary operator to str_plural() helper
mmc: rtsx_usb_sdmmc: Add 74 clocks in poweron flow
mmc: rtsx_usb_sdmmc: Re-work the code in sd_set_power_mode()
...
- Fix two initialization ordering issues in the cpufreq core and a
governor initialization error path in it, and clean it up (Lifeng
Zheng)
- Add Granite Rapids support in no-HWP mode to the intel_pstate cpufreq
driver (Li RongQing)
- Make intel_pstate always use HWP_DESIRED_PERF when operating in the
passive mode (Rafael Wysocki)
- Allow building the tegra124 cpufreq driver as a module (Aaron Kling)
- Do minor cleanups for Rust cpufreq and cpumask APIs and fix MAINTAINERS
entry for cpu.rs (Abhinav Ananthu, Ritvik Gupta, Lukas Bulwahn)
- Clean up assorted cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Krzysztof Kozlowski, Sven Peter, Svyatoslav Ryhel, Lifeng Zheng)
- Add the NEED_UPDATE_LIMITS flag to the CPPC cpufreq driver (Prashant
Malani)
- Fix minimum performance state label error in the amd-pstate driver
documentation (Shouye Liu)
- Add the CPUFREQ_GOV_STRICT_TARGET flag to the userspace cpufreq
governor and explain HW coordination influence on it in the
documentation (Shashank Balaji)
- Fix opencoded for_each_cpu() in idle_state_valid() in the DT cpuidle
driver (Yury Norov)
- Remove info about non-existing QoS interfaces from the PM QoS
documentation (Ulf Hansson)
- Use c_* types via kernel prelude in Rust for OPP (Abhinav Ananthu)
- Add HiSilicon uncore frequency scaling driver to devfreq (Jie Zhan)
- Allow devfreq drivers to add custom sysfs ABIs (Jie Zhan)
- Simplify the sun8i-a33-mbus devfreq driver by using more devm
functions (Uwe Kleine-König)
- Fix an index typo in trans_stat() in devfreq (Chanwoo Choi)
- Check devfreq governor before using governor->name (Lifeng Zheng)
- Remove a redundant devfreq_get_freq_range() call from
devfreq_add_device() (Lifeng Zheng)
- Limit max_freq with scaling_min_freq in devfreq (Lifeng Zheng)
- Replace sscanf() with kstrtoul() in set_freq_store() (Lifeng Zheng)
- Extend the asynchronous suspend and resume of devices to handle
suppliers like parents and consumers like children (Rafael Wysocki)
- Make pm_runtime_force_resume() work for drivers that set the
DPM_FLAG_SMART_SUSPEND flag and allow PCI drivers and drivers that
collaborate with the general ACPI PM domain to set it (Rafael
Wysocki)
- Add kernel parameter to disable asynchronous suspend/resume of
devices (Tudor Ambarus)
- Drop redundant might_sleep() calls from some functions in the device
suspend/resume core code (Zhongqiu Han)
- Fix the handling of monitors connected right before waking up the
system from sleep (tuhaowen)
- Clean up MAINTAINERS entries for suspend and hibernation (Rafael
Wysocki)
- Fix error code path in the KEXEC_JUMP flow and drop a redundant
pm_restore_gfp_mask() call from it (Rafael Wysocki)
- Rearrange suspend/resume error handling in the core device suspend
and resume code (Rafael Wysocki)
- Fix up white space that does not follow coding style in the
hibernation core code (Darshan Rathod)
- Document return values of suspend-related API functions in the
runtime PM framework (Sakari Ailus)
- Mark last busy stamp in multiple autosuspend-related functions in the
runtime PM framework and update its documentation (Sakari Ailus)
- Take active children into account in pm_runtime_get_if_in_use() for
consistency (Rafael Wysocki)
- Fix NULL pointer dereference in get_pd_power_uw() in the dtpm_cpu
power capping driver (Sivan Zohar-Kotzer)
- Add support for the Bartlett Lake platform to the Intel RAPL power
capping driver (Qiao Wei)
- Add PL4 support for Panther Lake to the intel_rapl_msr power capping
driver (Zhang Rui)
- Update contact information in the PM ABI docs and maintainer
information in the power domains DT binding (Rafael Wysocki)
- Update PM header inclusions to follow the IWYU (Include What You Use)
principle (Andy Shevchenko)
- Add flags to specify power on attach/detach for PM domains, make the
driver core detach PM domains in device_unbind_cleanup(), and drop
the dev_pm_domain_detach() call from the platform bus type (Claudiu
Beznea)
- Improve Python binding's Makefile for cpupower (John B. Wyatt IV)
- Fix printing of CORE, CPU fields in cpupower-monitor (Gautham Shenoy)
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmh/wC4SHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1O6MIAJtfclAleksv+PzbEyC+yk72zKinJg35
WJUk4Kz1yMOqAPazbpXRXt1tuxqyB3HWeixnTFyZbz+bbhZjYJ0lvpWGkdsFaS0i
NSbILSpHNGtOrP6s6hVKTBmLAdAzdWYWMQizlWgGrkhOiN5BnQzL7pAi2aGqu9KS
tGqnIg/3QwBAvnxijgpkm7qozOUMPJ9dzSvxMaFeB6JH7SNbTOODVFtsoD+mbJlH
YVMMWxih8b4MRJgAo4N2bL1Glp/Qnwg4ACawnQokt8Rknbtwku57QF9YwTbubr36
Ok7qbNnUSx0h9KtMQQNogLLkFreTJkbGknVWEwaWWhXNeW9l4cr6MWo=
=xVF9
-----END PGP SIGNATURE-----
Merge tag 'pm-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"As is tradition, cpufreq is the part with the largest number of
updates that include core fixes and cleanups as well as updates of
several assorted drivers, but there are also quite a few updates
related to system sleep, mostly focused on asynchronous suspend and
resume of devices and on making the integration of system suspend
and resume with runtime PM easier.
Runtime PM is also updated to allow some code duplication in drivers
to be eliminated going forward and to work more consistently overall
in some cases.
Apart from that, there are some driver core updates related to PM
domains that should help to address ordering issues with devm_ cleanup
routines relying on PM domains, some assorted devfreq updates
including core fixes and cleanups, tooling updates, and documentation
and MAINTAINERS updates.
Specifics:
- Fix two initialization ordering issues in the cpufreq core and a
governor initialization error path in it, and clean it up (Lifeng
Zheng)
- Add Granite Rapids support in no-HWP mode to the intel_pstate
cpufreq driver (Li RongQing)
- Make intel_pstate always use HWP_DESIRED_PERF when operating in the
passive mode (Rafael Wysocki)
- Allow building the tegra124 cpufreq driver as a module (Aaron
Kling)
- Do minor cleanups for Rust cpufreq and cpumask APIs and fix
MAINTAINERS entry for cpu.rs (Abhinav Ananthu, Ritvik Gupta, Lukas
Bulwahn)
- Clean up assorted cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Krzysztof Kozlowski, Sven Peter, Svyatoslav Ryhel, Lifeng Zheng)
- Add the NEED_UPDATE_LIMITS flag to the CPPC cpufreq driver
(Prashant Malani)
- Fix minimum performance state label error in the amd-pstate driver
documentation (Shouye Liu)
- Add the CPUFREQ_GOV_STRICT_TARGET flag to the userspace cpufreq
governor and explain HW coordination influence on it in the
documentation (Shashank Balaji)
- Fix opencoded for_each_cpu() in idle_state_valid() in the DT
cpuidle driver (Yury Norov)
- Remove info about non-existing QoS interfaces from the PM QoS
documentation (Ulf Hansson)
- Use c_* types via kernel prelude in Rust for OPP (Abhinav Ananthu)
- Add HiSilicon uncore frequency scaling driver to devfreq (Jie Zhan)
- Allow devfreq drivers to add custom sysfs ABIs (Jie Zhan)
- Simplify the sun8i-a33-mbus devfreq driver by using more devm
functions (Uwe Kleine-König)
- Fix an index typo in trans_stat() in devfreq (Chanwoo Choi)
- Check devfreq governor before using governor->name (Lifeng Zheng)
- Remove a redundant devfreq_get_freq_range() call from
devfreq_add_device() (Lifeng Zheng)
- Limit max_freq with scaling_min_freq in devfreq (Lifeng Zheng)
- Replace sscanf() with kstrtoul() in set_freq_store() (Lifeng Zheng)
- Extend the asynchronous suspend and resume of devices to handle
suppliers like parents and consumers like children (Rafael Wysocki)
- Make pm_runtime_force_resume() work for drivers that set the
DPM_FLAG_SMART_SUSPEND flag and allow PCI drivers and drivers that
collaborate with the general ACPI PM domain to set it (Rafael
Wysocki)
- Add kernel parameter to disable asynchronous suspend/resume of
devices (Tudor Ambarus)
- Drop redundant might_sleep() calls from some functions in the
device suspend/resume core code (Zhongqiu Han)
- Fix the handling of monitors connected right before waking up the
system from sleep (tuhaowen)
- Clean up MAINTAINERS entries for suspend and hibernation (Rafael
Wysocki)
- Fix error code path in the KEXEC_JUMP flow and drop a redundant
pm_restore_gfp_mask() call from it (Rafael Wysocki)
- Rearrange suspend/resume error handling in the core device suspend
and resume code (Rafael Wysocki)
- Fix up white space that does not follow coding style in the
hibernation core code (Darshan Rathod)
- Document return values of suspend-related API functions in the
runtime PM framework (Sakari Ailus)
- Mark last busy stamp in multiple autosuspend-related functions in
the runtime PM framework and update its documentation (Sakari
Ailus)
- Take active children into account in pm_runtime_get_if_in_use() for
consistency (Rafael Wysocki)
- Fix NULL pointer dereference in get_pd_power_uw() in the dtpm_cpu
power capping driver (Sivan Zohar-Kotzer)
- Add support for the Bartlett Lake platform to the Intel RAPL power
capping driver (Qiao Wei)
- Add PL4 support for Panther Lake to the intel_rapl_msr power
capping driver (Zhang Rui)
- Update contact information in the PM ABI docs and maintainer
information in the power domains DT binding (Rafael Wysocki)
- Update PM header inclusions to follow the IWYU (Include What You
Use) principle (Andy Shevchenko)
- Add flags to specify power on attach/detach for PM domains, make
the driver core detach PM domains in device_unbind_cleanup(), and
drop the dev_pm_domain_detach() call from the platform bus type
(Claudiu Beznea)
- Improve Python binding's Makefile for cpupower (John B. Wyatt IV)
- Fix printing of CORE, CPU fields in cpupower-monitor (Gautham
Shenoy)"
* tag 'pm-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
cpufreq: CPPC: Mark driver with NEED_UPDATE_LIMITS flag
PM: docs: Use my kernel.org address in ABI docs and DT bindings
PM: hibernate: Fix up white space that does not follow coding style
PM: sleep: Rearrange suspend/resume error handling in the core
Documentation: amd-pstate:fix minimum performance state label error
PM: runtime: Take active children into account in pm_runtime_get_if_in_use()
kexec_core: Drop redundant pm_restore_gfp_mask() call
kexec_core: Fix error code path in the KEXEC_JUMP flow
PM: sleep: Clean up MAINTAINERS entries for suspend and hibernation
drivers: cpufreq: add Tegra114 support
rust: cpumask: Replace `MaybeUninit` and `mem::zeroed` with `Opaque` APIs
cpufreq: Exit governor when failed to start old governor
cpufreq: Move the check of cpufreq_driver->get into cpufreq_verify_current_freq()
cpufreq: Init policy->rwsem before it may be possibly used
cpufreq: Initialize cpufreq-based frequency-invariance later
cpufreq: Remove duplicate check in __cpufreq_offline()
cpufreq: Contain scaling_cur_freq.attr in cpufreq_attrs
cpufreq: intel_pstate: Add Granite Rapids support in no-HWP mode
cpufreq: intel_pstate: Always use HWP_DESIRED_PERF in passive mode
PM / devfreq: Add HiSilicon uncore frequency scaling driver
...
Merge miscellaneous power management updates and cpupower utility
updates for 6.17-rc1:
- Update contact information in the PM ABI docs and maintainer
information in the power domains DT binding (Rafael Wysocki)
- Update PM header inclusions to follow the IWYU (Include What You Use)
principle (Andy Shevchenko)
- Add flags to specify power on attach/detach for PM domains, make the
driver core detach PM domains in device_unbind_cleanup(), and drop
the dev_pm_domain_detach() call from the platform bus type (Claudiu
Beznea)
- Improve Python binding's Makefile for cpupower (John B. Wyatt IV)
- Fix printing of CORE, CPU fields in cpupower-monitor (Gautham Shenoy)
* pm-misc:
PM: docs: Use my kernel.org address in ABI docs and DT bindings
driver core: platform: Drop dev_pm_domain_detach() call
PM: domains: Detach on device_unbind_cleanup()
PM: domains: Add flags to specify power on attach/detach
PM: Don't use "proxy" headers
* pm-tools:
cpupower: Improve Python binding's Makefile
pm: cpupower: Fix printing of CORE, CPU fields in cpupower-monitor
pm: cpupower: Fix the snapshot-order of tsc,mperf, clock in mperf_stop()
The function prefixes for loongson2_mmc_pdata follow two naming
conventions: SoC-based and DMA-based.
First, DMA-based prefixes are the preferred choice, as they clearly
highlight differences, such as prepare_dma; however, for functions
related to SoC, such as reorder_cmd_data, it is agreed to use the
smallest SoC name as the fallback prefix, such as ls2k0500.
No functional change intended.
Suggested-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250716064421.3823418-1-zhoubinbin@loongson.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a cut and paste bug so we accidentally return the wrong
variable. It should be "ret" instead of PTR_ERR(host->clk).
Fixes: 2115772014 ("mmc: loongson2: Add Loongson-2K SD/SDIO controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/847bf395-6d62-49c9-a39d-8e82c5b17bf7@sabinyo.mountain
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704075434.3220506-1-sakari.ailus@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Calling dev_pm_domain_attach()/dev_pm_domain_detach() in bus driver
probe/remove functions can affect system behavior when the drivers
attached to the bus use devres-managed resources. Since devres actions
may need to access device registers, calling dev_pm_domain_detach() too
early, i.e., before these actions complete, can cause failures on some
systems. One such example is Renesas RZ/G3S SoC-based platforms.
If the device clocks are managed via PM domains, invoking
dev_pm_domain_detach() in the bus driver's remove function removes the
device's clocks from the PM domain, preventing any subsequent
pm_runtime_resume*() calls from enabling those clocks.
The second argument of dev_pm_domain_attach() specifies whether the PM
domain should be powered on during attachment. Likewise, the second
argument of dev_pm_domain_detach() indicates whether the domain should be
powered off during detachment.
Upcoming changes address the issue described above (initially for the
platform bus only) by deferring the call to dev_pm_domain_detach() until
after devres_release_all() in device_unbind_cleanup(). The detach_power_off
field in struct dev_pm_info stores the detach power off info from the
second argument of dev_pm_domain_attach().
Because there are cases where the device's PM domain power-on/off behavior
must be conditional (e.g., in i2c_device_probe()), the patch introduces
PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF flags to be passed
to dev_pm_domain_attach().
Finally, dev_pm_domain_attach() and its users are updated to use the newly
introduced PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF macros.
This change is preparatory.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # I2C
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20250703112708.1621607-2-claudiu.beznea.uj@bp.renesas.com
[ rjw: Changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many mobile phones feature multi-card tray designs, where the same
tray is used for both SD and SIM cards. If the SD card is placed
at the outermost location in the tray, the SIM card may come in
contact with SD card power-supply while removing the tray, possibly
resulting in SIM damage.
To prevent that, make sure the SD card is really inserted by reading
the Card Detect pin state. If it's not, turn off the power in
sdhci_msm_check_power_status() and also set the BUS_FAIL power state
on the controller as part of pwr_irq handling for BUS_ON request.
Signed-off-by: Sarthak Garg <quic_sartgarg@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250701100659.3310386-1-quic_sartgarg@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.16-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.17.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i2312 [0] for K3 silicon mentions the maximum obtainable
timeout through MMC host controller is 700ms. And for commands taking
longer than 700ms, hardware timeout should be disabled and software
timeout should be used.
The workaround for Errata i2312 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci_am654.
[0] https://www.ti.com/lit/pdf/sprz487
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 41fd4caeb0 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250626231452.3460987-1-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of using of_property_read_bool to check the presence of the
cdns,phy-* properties in the device tree, use of_property_present in
function sdhci_cdns_phy_param_count.
This silences the following warning messages since the cdns,phy-*
properties are all u32, not boolean.
OF: /soc/sdhci@d8010000: Read of boolean property 'cdns,phy-input-delay-legacy' with a value.
OF: /soc/sdhci@d8010000: Read of boolean property 'cdns,phy-input-delay-mmc-highspeed' with a value.
OF: /soc/sdhci@d8010000: Read of boolean property 'cdns,phy-input-delay-mmc-ddr' with a value.
OF: /soc/sdhci@d8010000: Read of boolean property 'cdns,phy-dll-delay-sdclk' with a value.
OF: /soc/sdhci@d8010000: Read of boolean property 'cdns,phy-dll-delay-sdclk-hsmmc' with a value.
Signed-off-by: Benoît Monin <benoit.monin@bootlin.com>
Link: https://lore.kernel.org/r/e244c1377f7b2ad5d026c9d9368a08de3887129f.1750943549.git.benoit.monin@bootlin.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch describes the two MMC controllers of the Loongson-2K2000 SoC,
one providing an eMMC interface and the other exporting an SD/SDIO
interface.
Compared to the Loongson-2K1000's MMC controllers, their internals are
similar, except that we use an internally exclusive DMA engine instead of
an externally shared APBDMA engine.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/1df46b976abd36003bd553ad8a039e5c97369df0.1750765495.git.zhoubinbin@loongson.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC controllers on the Loongson-2K series CPUs are similar,
except for the interface characteristics and the use of DMA controllers.
This patch describes the MMC controllers on the Loongson-2K0500/2K1000,
with the distinguishing feature being the use of an externally shared
APBDMA engine.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/c0a9f0c0279d8e09165c6e2d694b0c35f7fc7e31.1750765495.git.zhoubinbin@loongson.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace direct ternary condition check with existing helper function
str_true_false() to improve code readability and maintain consistency.
Signed-off-by: Li Dong <lidong@vivo.com>
Link: https://lore.kernel.org/r/20250620043517.172705-1-lidong@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.16-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.17.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Do not leave host with dangling ->mrq pointer if we hit
the msdc_prepare_data() error out path.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Fixes: f5de469990 ("mtk-sd: Prevent memory corruption from DMA map failure")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250625052106.584905-1-senozhatsky@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.16-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.17.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out the trying to strictly conform to the SDHCI specification
is causing problems. Let's revert and start over.
This reverts commit fb3bbc46c9.
Cc: Erick Shepherd <erick.shepherd@ni.com>
Cc: stable@vger.kernel.org
Fixes: fb3bbc46c9 ("mmc: sdhci: Disable SD card clock before changing parameters")
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Reported-by: Jonathan Liu <net147@gmail.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Closes: https://bugs.debian.org/1108065
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20250624110932.176925-1-ulf.hansson@linaro.org
Merge the mmc fixes for v6.16-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.17.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns (or errors with CONFIG_WERROR=y):
drivers/mmc/host/rtsx_usb_sdmmc.c:1042:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
1042 | case MMC_POWER_UNDEFINED:
| ^
drivers/mmc/host/rtsx_usb_sdmmc.c:1042:2: note: insert 'break;' to avoid fall-through
1042 | case MMC_POWER_UNDEFINED:
| ^
| break;
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Fixes: 2c3809bd6f65 ("mmc: rtsx_usb_sdmmc: Add 74 clocks in poweron flow")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250620-mmc-rtsx-usb-sdmmc-fix-clang-implicit-fallthrough-v1-1-4031d11159c0@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace direct ternary condition check with existing helper function
str_plural() to improve code readability and maintain consistency.
Signed-off-by: Li Dong <lidong@vivo.com>
Link: https://lore.kernel.org/r/20250618115954.10260-1-lidong@vivo.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To conform with SD spec definition, that the host must provide at least 74
clocks before issuing first command, let's add these clock cycles at
MMC_POWER_UP.
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20250616064956.1846258-1-ricky_wu@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's only at MMC_POWER_OFF and at MMC_POWER_UP when some operations must be
carried out in sd_set_power_mode(). The code is a bit obfuscated in this
regards. Let's convert it into a switch-case-clause to make this clear.
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20250610111633.504366-5-ulf.hansson@linaro.org
The sdmmc_set_ios() is the only caller of sd_set_power_mode() and it
ignores the return code. Let's therefore convert sd_set_power_mode() into a
void function instead.
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20250610111633.504366-4-ulf.hansson@linaro.org
It should be useful to know when we fail to power-on/off a card. Let's
therefore print debug-messages when this happens.
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20250610111633.504366-3-ulf.hansson@linaro.org
In the error path of sd_set_power_mode() we don't update host->power_mode,
which could lead to an imbalance of the runtime PM usage count. Fix this by
always updating host->power_mode.
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20250610111633.504366-2-ulf.hansson@linaro.org
This host controller is possible to change incorrect tap if an SDIO
card is used because DAT1 is used for interrupt signal on SDIO standard
but the controller doesn't take care of it. So, in the worst case,
this behavior causes a CRC error.
To resolve the issue, this driver uses manual correction mode instead
of auto correction if an SDIO card is used. Also, even if DAT1 is
mismatched on an SDIO card, this driver will not change the TAP.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250610072545.2001435-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI controller requires vender specific handling when
an SDIO irq occurs. So, add .sdio_irq() to the tmio core.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250610072545.2001435-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the devm_mmc_alloc_host() helper is already in use,
sdhci_pltfm_free() is no longer needed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/88a24d5f60bc916712cca813e24ae49b7e691eb2.1749127796.git.zhoubinbin@loongson.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the devm_mmc_alloc_host() helper is already in use,
sdhci_pltfm_free() is no longer needed.
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Acked-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/67b5e9076056da66d9fc8951fafd4f48ddd3ca25.1749127796.git.zhoubinbin@loongson.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
