If a controller (usually, eDP!) does not support audio, or audio is not
enabled because the endpoint has no audio support, it's useless to lock
a mutex only to unlock it right after because there's no .plugged_cb().
Check if the audio is supported and enabled before locking the mutex in
mtk_dp_update_plugged_status(): if not, we simply return immediately.
While at it, since the update_plugged_status_lock mutex would not be
used if the controller doesn't support audio at all, initialize it
only if `audio_supported` is true.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-8-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
It is useless and error-prone to enable the DisplayPort event interrupt
before finishing to probe and install the driver, as the DP training
cannot happen before the entire pipeline is correctly set up, as the
interrupt handler also requires the full hardware to be initialized by
mtk_dp_bridge_attach().
Anyway, depending in which state the controller is left from the
bootloader, this may cause an interrupt storm and consequently hang
the kernel during boot, so, avoid enabling the interrupt until we
reach a clean state by adding the IRQ_NOAUTOEN flag before requesting
it at probe time and manage the enablement of the ISR in the .attach()
and .detach() handlers for the DP bridge.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-7-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Move the register write to MTK_DP_AUX_P0_3690 to set the AUX reply mode
to function mtk_dp_initialize_aux_settings(), as this is effectively
part of the DPTX AUX setup sequence.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-6-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for aux-bus, which will add a code
path that may fail after the drm_bridge_add() call, change that to
devm_drm_bridge_add() to simplify failure paths later.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-5-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Change logging from drm_{err,info}() to dev_{err,info}() in functions
mtk_dp_aux_transfer() and mtk_dp_aux_do_transfer(): this will be
essential to avoid getting NULL pointer kernel panics if any kind
of error happens during AUX transfers happening before the bridge
is attached.
This may potentially start happening in a later commit implementing
aux-bus support, as AUX transfers will be triggered from the panel
driver (for EDID) before the mtk-dp bridge gets attached, and it's
done in preparation for the same.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Everytime we run bridge detection and/or EDID read we run a poweron
and poweroff sequence for both the AUX and the panel; moreover, this
is also done when enabling the bridge in the .atomic_enable() callback.
Move this power on/off sequence to a new mtk_dp_aux_panel_poweron()
function as to commonize it.
Note that, before this commit, in mtk_dp_bridge_atomic_enable() only
the AUX was getting powered on but the panel was left powered off if
the DP cable wasn't plugged in while now we unconditionally send a D0
request and this is done for two reasons:
- First, whether this request fails or not, it takes the same time
and anyway the DP hardware won't produce any error (or, if it
does, it's ignorable because it won't block further commands)
- Second, training the link between a sleeping/standby/unpowered
display makes little sense.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
If reading the RX capabilities fails the training pattern will be set
wrongly: add error checking for drm_dp_read_dpcd_caps() and return if
anything went wrong with it.
While at it, also add a less critical error check when writing to
clear the ESI0 IRQ vector.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-2-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reduce line count by compressing the entries of struct of_device_id;
while at it, also add the usual /* sentinel */ comment to the last
entry.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230726082245.550929-7-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Instead of the open-coded platform_get_resource, devm_ioremap_resource
switch to devm_platform_ioremap_resource(), also dropping the useless
struct resource pointer, which becomes unused.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230726082245.550929-6-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Function drm_of_find_panel_or_bridge() is marked as deprecated: since
the usage of that in this driver exactly corresponds to the new function
devm_drm_of_get_bridge(), switch to it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230726082245.550929-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmSvvRAACgkQaA3BHVML
eiNpGQgAs8jq1XjN9t8jZsdgXnoCbkZyVUI2NO0HwoVwpRCLgbXp5AX5qq2oRciE
TBhe4Fceh/ZsYqHTZQahnguxgRKM5JgXwbI4Z0iiOVcqasNbycaKAqipxJJ7kdo1
qPhGCbgQFVX7oIq2xjfXehh6O0SYX+R9r88X8dMJxMYv/pcLwOHG74kS040WOcQq
uATgcnobOf/D8ZmlqvfKGAeTUoFo/RSR2Uhlauka58qgeUbicrTELZT2barY9d+k
as6U5vv4wx2zMklTkjrlkMpAT1ZpbB9d3jGHwL27VEnjlfd3wV2bdH7Dzn9qZRf/
gn0ALg/b3u5yBWk/k7YBvijXyNcH6Q==
=bBuG
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-07-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
Clear all assignments of struct drm_driver's fd/handle callbacks to
drm_gem_prime_fd_to_handle() and drm_gem_prime_handle_to_fd(). These
functions are called by default. Add a TODO item to convert vmwgfx
to the defaults as well.
v2:
* remove TODO item (Zack)
* also update amdgpu's amdgpu_partition_driver
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Simon Ser <contact@emersion.fr>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Jeffrey Hugo <quic_jhugo@quicinc.com> # qaic
Link: https://patchwork.freedesktop.org/patch/msgid/20230620080252.16368-3-tzimmermann@suse.de
All drivers initialize this field with drm_gem_prime_mmap(). Call
the function directly and remove the field. Simplifies the code and
resolves a long-standing TODO item.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230613150441.17720-3-tzimmermann@suse.de
DP 1.4a Section 2.8.7.1.5.6.1:
A DP Source device shall retry at least seven times upon receiving
AUX_DEFER before giving up the AUX transaction.
The drm_dp_i2c_do_msg() function in the drm_dp_helper.c file will
judge the status of the msg->reply parameter passed to aux_transfer
for different processing.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1680072203-10394-1-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
1. Add ovl_adaptor get_format and get_num_formats component function.
The two functions are needed for getting the supported format in
mtk_plane_init().
2. Get supported format from the ovl_adaptor's rdma engine - mdp_rdma.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230330032614.18837-3-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add driver data of mt8188 vdosys0 to mediatek-drm and the sub driver.
Signed-off-by: amy zhang <Amy.Zhang@mediatek.com>
Signed-off-by: Nathan Lu <nathan.lu@mediatek.com>
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230324100553.13719-1-jason-jh.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add driver data of mt8195 vdosys1 to mediatek-drm.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-8-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add drm ovl_adaptor sub driver. Bring up ovl_adaptor sub driver if
the component exists in the path.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-7-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
MT8195 have two mmsys. Modify drm for MT8195 multi-mmsys support.
The two mmsys (vdosys0 and vdosys1) will bring up two drm drivers,
only one drm driver register as the drm device.
Each drm driver binds its own component. The last bind drm driver
allocates and registers the drm device to drm core.
Each crtc path is created with the corresponding drm driver data.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-6-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This is a preparation for adding support for the ovl_adaptor sub driver
Ovl_adaptor is a DRM sub driver, which doesn't have dma dev. Add
dma_dev_get function for getting representative dma dev in ovl_adaptor.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioachino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-5-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add ovl_adaptor driver for MT8195.
Ovl_adaptor is an encapsulated module and designed for simplified
DRM control flow. This module is composed of 8 RDMAs, 4 MERGEs and
an ETHDR. Two RDMAs merge into one layer, so this module support 4
layers.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-4-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
ETHDR is a part of ovl_adaptor.
ETHDR is designed for HDR video and graphics conversion in the external
display path. It handles multiple HDR input types and performs tone
mapping, color space/color format conversion, and then combine
different layers, output the required HDR or SDR signal to the
subsequent display path.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-3-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The MediaTek DisplayPort interface bridge driver starts its interrupts
as soon as its probed. However when the interrupts trigger the bridge
might not have been attached to a DRM device. As drm_helper_hpd_irq_event()
does not check whether the passed in drm_device is valid or not, a NULL
pointer passed in results in a kernel NULL pointer dereference in it.
Check whether the bridge is attached and only trigger an HPD event if
it is.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230202045734.2773503-1-wenst@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Modify the overlay driver data for MT8195 to enable bit depth control and
enable support for AR30 and BA30 framebuffer formats. This patch in
combination with the previous two patches in the series will allow MT8195
devices to scanout AR30 and BA30 framebuffers.
Tested using "modetest -P" on an MT8195 device. The test pattern displays
correctly for both AR30 and BA30 formats.
Signed-off-by: Justin Green <greenjustin@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230309210416.1167020-4-greenjustin@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add the ability for the Mediatek DRM driver to control
the bit depth register. If the DTS indicates the device supports
10-bit overlays and the current format has a fourcc of AR30, BA30,
or RA30, we set the bit depth register to 10 bit.
The next patch in the series actually enables 10-bit overlays for
MT8195 devices, but this current patch should be a no-op. This
patch was tested by simply running Chrome on an MT8195 and looking
for regressions.
Signed-off-by: Justin Green <greenjustin@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230309210623.1167567-1-greenjustin@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add an DDP component interface for querying pixel format support
and move list of supported pixel formats into DDP components
instead of mtk_drm_plane.c
Tested by running Chrome on an MT8195.
Signed-off-by: Justin Green <greenjustin@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230309210416.1167020-2-greenjustin@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Because compatible of mt8195 is changing from "mediatek,mt8195-mmsys"
to "mediatek,mt8195-vdosys0".
We have to revert the multiple compatible finding function and
add driver data of mt8195 vdosys0 to mediatek-drm and the sub driver.
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230306080659.15261-2-jason-jh.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
F_SEAL_EXEC") which permits the setting of the memfd execute bit at
memfd creation time, with the option of sealing the state of the X bit.
- Peter Xu adds a patch series ("mm/hugetlb: Make huge_pte_offset()
thread-safe for pmd unshare") which addresses a rare race condition
related to PMD unsharing.
- Several folioification patch serieses from Matthew Wilcox, Vishal
Moola, Sidhartha Kumar and Lorenzo Stoakes
- Johannes Weiner has a series ("mm: push down lock_page_memcg()") which
does perform some memcg maintenance and cleanup work.
- SeongJae Park has added DAMOS filtering to DAMON, with the series
"mm/damon/core: implement damos filter". These filters provide users
with finer-grained control over DAMOS's actions. SeongJae has also done
some DAMON cleanup work.
- Kairui Song adds a series ("Clean up and fixes for swap").
- Vernon Yang contributed the series "Clean up and refinement for maple
tree".
- Yu Zhao has contributed the "mm: multi-gen LRU: memcg LRU" series. It
adds to MGLRU an LRU of memcgs, to improve the scalability of global
reclaim.
- David Hildenbrand has added some userfaultfd cleanup work in the
series "mm: uffd-wp + change_protection() cleanups".
- Christoph Hellwig has removed the generic_writepages() library
function in the series "remove generic_writepages".
- Baolin Wang has performed some maintenance on the compaction code in
his series "Some small improvements for compaction".
- Sidhartha Kumar is doing some maintenance work on struct page in his
series "Get rid of tail page fields".
- David Hildenbrand contributed some cleanup, bugfixing and
generalization of pte management and of pte debugging in his series "mm:
support __HAVE_ARCH_PTE_SWP_EXCLUSIVE on all architectures with swap
PTEs".
- Mel Gorman and Neil Brown have removed the __GFP_ATOMIC allocation
flag in the series "Discard __GFP_ATOMIC".
- Sergey Senozhatsky has improved zsmalloc's memory utilization with his
series "zsmalloc: make zspage chain size configurable".
- Joey Gouly has added prctl() support for prohibiting the creation of
writeable+executable mappings. The previous BPF-based approach had
shortcomings. See "mm: In-kernel support for memory-deny-write-execute
(MDWE)".
- Waiman Long did some kmemleak cleanup and bugfixing in the series
"mm/kmemleak: Simplify kmemleak_cond_resched() & fix UAF".
- T.J. Alumbaugh has contributed some MGLRU cleanup work in his series
"mm: multi-gen LRU: improve".
- Jiaqi Yan has provided some enhancements to our memory error
statistics reporting, mainly by presenting the statistics on a per-node
basis. See the series "Introduce per NUMA node memory error
statistics".
- Mel Gorman has a second and hopefully final shot at fixing a CPU-hog
regression in compaction via his series "Fix excessive CPU usage during
compaction".
- Christoph Hellwig does some vmalloc maintenance work in the series
"cleanup vfree and vunmap".
- Christoph Hellwig has removed block_device_operations.rw_page() in ths
series "remove ->rw_page".
- We get some maple_tree improvements and cleanups in Liam Howlett's
series "VMA tree type safety and remove __vma_adjust()".
- Suren Baghdasaryan has done some work on the maintainability of our
vm_flags handling in the series "introduce vm_flags modifier functions".
- Some pagemap cleanup and generalization work in Mike Rapoport's series
"mm, arch: add generic implementation of pfn_valid() for FLATMEM" and
"fixups for generic implementation of pfn_valid()"
- Baoquan He has done some work to make /proc/vmallocinfo and
/proc/kcore better represent the real state of things in his series
"mm/vmalloc.c: allow vread() to read out vm_map_ram areas".
- Jason Gunthorpe rationalized the GUP system's interface to the rest of
the kernel in the series "Simplify the external interface for GUP".
- SeongJae Park wishes to migrate people from DAMON's debugfs interface
over to its sysfs interface. To support this, we'll temporarily be
printing warnings when people use the debugfs interface. See the series
"mm/damon: deprecate DAMON debugfs interface".
- Andrey Konovalov provided the accurately named "lib/stackdepot: fixes
and clean-ups" series.
- Huang Ying has provided a dramatic reduction in migration's TLB flush
IPI rates with the series "migrate_pages(): batch TLB flushing".
- Arnd Bergmann has some objtool fixups in "objtool warning fixes".
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY/PoPQAKCRDdBJ7gKXxA
jlvpAPsFECUBBl20qSue2zCYWnHC7Yk4q9ytTkPB/MMDrFEN9wD/SNKEm2UoK6/K
DmxHkn0LAitGgJRS/W9w81yrgig9tAQ=
=MlGs
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-02-20-13-37' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Daniel Verkamp has contributed a memfd series ("mm/memfd: add
F_SEAL_EXEC") which permits the setting of the memfd execute bit at
memfd creation time, with the option of sealing the state of the X
bit.
- Peter Xu adds a patch series ("mm/hugetlb: Make huge_pte_offset()
thread-safe for pmd unshare") which addresses a rare race condition
related to PMD unsharing.
- Several folioification patch serieses from Matthew Wilcox, Vishal
Moola, Sidhartha Kumar and Lorenzo Stoakes
- Johannes Weiner has a series ("mm: push down lock_page_memcg()")
which does perform some memcg maintenance and cleanup work.
- SeongJae Park has added DAMOS filtering to DAMON, with the series
"mm/damon/core: implement damos filter".
These filters provide users with finer-grained control over DAMOS's
actions. SeongJae has also done some DAMON cleanup work.
- Kairui Song adds a series ("Clean up and fixes for swap").
- Vernon Yang contributed the series "Clean up and refinement for maple
tree".
- Yu Zhao has contributed the "mm: multi-gen LRU: memcg LRU" series. It
adds to MGLRU an LRU of memcgs, to improve the scalability of global
reclaim.
- David Hildenbrand has added some userfaultfd cleanup work in the
series "mm: uffd-wp + change_protection() cleanups".
- Christoph Hellwig has removed the generic_writepages() library
function in the series "remove generic_writepages".
- Baolin Wang has performed some maintenance on the compaction code in
his series "Some small improvements for compaction".
- Sidhartha Kumar is doing some maintenance work on struct page in his
series "Get rid of tail page fields".
- David Hildenbrand contributed some cleanup, bugfixing and
generalization of pte management and of pte debugging in his series
"mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE on all architectures with
swap PTEs".
- Mel Gorman and Neil Brown have removed the __GFP_ATOMIC allocation
flag in the series "Discard __GFP_ATOMIC".
- Sergey Senozhatsky has improved zsmalloc's memory utilization with
his series "zsmalloc: make zspage chain size configurable".
- Joey Gouly has added prctl() support for prohibiting the creation of
writeable+executable mappings.
The previous BPF-based approach had shortcomings. See "mm: In-kernel
support for memory-deny-write-execute (MDWE)".
- Waiman Long did some kmemleak cleanup and bugfixing in the series
"mm/kmemleak: Simplify kmemleak_cond_resched() & fix UAF".
- T.J. Alumbaugh has contributed some MGLRU cleanup work in his series
"mm: multi-gen LRU: improve".
- Jiaqi Yan has provided some enhancements to our memory error
statistics reporting, mainly by presenting the statistics on a
per-node basis. See the series "Introduce per NUMA node memory error
statistics".
- Mel Gorman has a second and hopefully final shot at fixing a CPU-hog
regression in compaction via his series "Fix excessive CPU usage
during compaction".
- Christoph Hellwig does some vmalloc maintenance work in the series
"cleanup vfree and vunmap".
- Christoph Hellwig has removed block_device_operations.rw_page() in
ths series "remove ->rw_page".
- We get some maple_tree improvements and cleanups in Liam Howlett's
series "VMA tree type safety and remove __vma_adjust()".
- Suren Baghdasaryan has done some work on the maintainability of our
vm_flags handling in the series "introduce vm_flags modifier
functions".
- Some pagemap cleanup and generalization work in Mike Rapoport's
series "mm, arch: add generic implementation of pfn_valid() for
FLATMEM" and "fixups for generic implementation of pfn_valid()"
- Baoquan He has done some work to make /proc/vmallocinfo and
/proc/kcore better represent the real state of things in his series
"mm/vmalloc.c: allow vread() to read out vm_map_ram areas".
- Jason Gunthorpe rationalized the GUP system's interface to the rest
of the kernel in the series "Simplify the external interface for
GUP".
- SeongJae Park wishes to migrate people from DAMON's debugfs interface
over to its sysfs interface. To support this, we'll temporarily be
printing warnings when people use the debugfs interface. See the
series "mm/damon: deprecate DAMON debugfs interface".
- Andrey Konovalov provided the accurately named "lib/stackdepot: fixes
and clean-ups" series.
- Huang Ying has provided a dramatic reduction in migration's TLB flush
IPI rates with the series "migrate_pages(): batch TLB flushing".
- Arnd Bergmann has some objtool fixups in "objtool warning fixes".
* tag 'mm-stable-2023-02-20-13-37' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (505 commits)
include/linux/migrate.h: remove unneeded externs
mm/memory_hotplug: cleanup return value handing in do_migrate_range()
mm/uffd: fix comment in handling pte markers
mm: change to return bool for isolate_movable_page()
mm: hugetlb: change to return bool for isolate_hugetlb()
mm: change to return bool for isolate_lru_page()
mm: change to return bool for folio_isolate_lru()
objtool: add UACCESS exceptions for __tsan_volatile_read/write
kmsan: disable ftrace in kmsan core code
kasan: mark addr_has_metadata __always_inline
mm: memcontrol: rename memcg_kmem_enabled()
sh: initialize max_mapnr
m68k/nommu: add missing definition of ARCH_PFN_OFFSET
mm: percpu: fix incorrect size in pcpu_obj_full_size()
maple_tree: reduce stack usage with gcc-9 and earlier
mm: page_alloc: call panic() when memoryless node allocation fails
mm: multi-gen LRU: avoid futile retries
migrate_pages: move THP/hugetlb migration support check to simplify code
migrate_pages: batch flushing TLB
migrate_pages: share more code between _unmap and _move
...
Replace direct modifications to vma->vm_flags with calls to modifier
functions to be able to track flag changes and to keep vma locking
correctness.
[akpm@linux-foundation.org: fix drivers/misc/open-dice.c, per Hyeonggon Yoo]
Link: https://lkml.kernel.org/r/20230126193752.297968-5-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Minchan Kim <minchan@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Peter Oskolkov <posk@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
-----BEGIN PGP SIGNATURE-----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=ZhnI
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.3' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.3
1. Reduce the time of dsi from LP11 to sending cmd
2. Remove dependency on GEM DMA helper
3. Drop unbalanced obj unref
4. Fix the fallback for mediatek,mt8186-disp-ccorr
5. Fixup for error path.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130125811.2567-1-chunkuang.hu@kernel.org
mtk_drm_bind() can fail, in which case drm_dev_put() is called,
destroying the drm_device object. However a pointer to it was still
being held in the private object, and that pointer would be passed along
to DRM in mtk_drm_sys_prepare() if a suspend were triggered at that
point, resulting in a panic. Clean the pointer when destroying the
object in the error path to prevent this from happening.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20221122143949.3493104-1-nfraprado@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
As the devm_kcalloc may return NULL, the return value needs to be checked
to avoid NULL poineter dereference.
Fixes: 31c5558dae ("drm/mediatek: Refactor plane init")
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20221205095115.2905090-1-ruanjinjie@huawei.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fix the follow sparse warnings by adding missing headers:
drivers/gpu/drm/mediatek/mtk_cec.c:251:24: sparse: warning: symbol 'mtk_cec_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_ccorr.c:221:24: sparse: warning: symbol 'mtk_disp_ccorr_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:390:24: sparse: warning: symbol 'mtk_disp_rdma_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_gamma.c:209:24: sparse: warning: symbol 'mtk_disp_gamma_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:565:24: sparse: warning: symbol 'mtk_disp_ovl_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_color.c:164:24: sparse: warning: symbol 'mtk_disp_color_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_aal.c:161:24: sparse: warning: symbol 'mtk_disp_aal_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_dpi.c:1109:24: sparse: warning: symbol 'mtk_dpi_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_hdmi_ddc.c:340:24: sparse: warning: symbol 'mtk_hdmi_ddc_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_dsi.c:1223:24: sparse: warning: symbol 'mtk_dsi_driver' was not declared. Should it be static?
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230110091647.13265-1-miles.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Use NULL for NULL pointer to fix the following sparse warning:
drivers/gpu/drm/mediatek/mtk_drm_gem.c:265:27: sparse: warning: Using plain integer as NULL pointer
Fixes: 3df64d7b0a ("drm/mediatek: Implement gem prime vmap/vunmap function")
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230111024443.24559-1-miles.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
According to Figure 16 Turnaround Procedure on page 36 in [1], you
can see the status of LP-00 -> LP10 -> LP11. This state can correspond
to the state of DSI from LP00 -> LP11 in mtk_dsi_lane_ready function
in mtk_dsi.c.
LP-00 -> LP10 -> LP11 takes about 2*TLPX time (refer to [1] page 51
to see that TLPX is 50ns)
The delay at the end of the mtk_dsi_lane_ready function should be
greater than the 2*TLPX specified by the DSI spec, and less than
the time specified by the DSI_RX (generally 6ms to 40ms), to avoid
problems caused by the RX specification
[1]:mipi_D-PHY_specification_v1-1
Fixes: 39e8d062b0 ("drm/mediatek: Keep dsi as LP00 before dcs cmds transfer")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1673330093-6771-2-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmO0B0QACgkQaA3BHVML
eiMKtAf9EXt5yaEonR4gsGNVD70VkebW+jPEWbEMg5hMFDHE9sjBja8T7bOxeeL1
BVofJiAuEZW9176eqeWvShuwOuiE7lf4WQLMvXfFmtHF/Nac9HUtEvOcvc1vEDUB
y6VFlVHe8mSp+Iy0WPLyZCtT4d7v2eM+VYm0HgFa74dSTzQTLGPiUI/XVb/YDaA7
FHKB5NvsMX9S1XvjxCsq0jA5bo8SSzh5CVKerdAZkBJMCSmKiY09o2p5C7vw3EAz
WUXL5CXqd9bwgvZa/9ZClQtpJaikNGoOaMSEl67rbWdVTk0LIpqx3nTY15py5LXd
SG4Wtfor3Vf1REa9TrR2uCIOmh+1gQ==
=0/PC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-01-03' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.3:
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y7QIwlfElAYWxRcR@linux-uq9g
Dpi output needs to adjust the output format to dual edge for MT8186.
Co-developed-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1666577099-3859-3-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Commit f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort
driver") added usage of the drm_bridge_chain_ functions which are
to be deprecated.
Replace with the drm_atomic_bridge_chain_ variants using the
current state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221205173328.1395350-3-dave.stevenson@raspberrypi.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
1. Fixup of dpi and hdmi
2. Move panel connector to head
3. Add MT8188 dpi support
4. Add MT8195 AFBC support
-----BEGIN PGP SIGNATURE-----
iQJMBAABCgA2FiEEACwLKSDmq+9RDv5P4cpzo8lZTiQFAmN+rUoYHGNodW5rdWFu
Zy5odUBrZXJuZWwub3JnAAoJEOHKc6PJWU4kaxAP/2rKCugXX0lacqrKqQqvMZ0s
lAcYI8s/J0oUOQ6kdmXUGlulE+F6YflvaNbwxGqZpkqUbcOYgR3/wi5yqKi2+LDl
R3RBeP2IAqlIES5KZZVKRUNg6MYyaiKY3JLm8o9Vs4ZnAKIG57u+6h4Dmue9kT0a
XRVWDwzPG5f8sBmWvwLYa2nMx51JjCuQqhzns3e7i+u/GCz/ON4V6EIfCu0m/Rtk
NXAbgJTrO4Ng9WesRQ17tF9mUvTCEdbPdkXK5rkAsw+JxYgKnvW6Q6u/zh8jyYKj
sFd/wVR1fRzim4KHHn2sSSCSfZ18A/No3FkA1a1OwRzqCIC5rtlUNLfWS776/ju4
WTHClraAkk1dxhamufYKum1ecQbDFT9//Hu4yvZdXDF2CWf9FHz6Dp41qJTH90WS
98HM6MrT+W5khSDWbFUY+ZXYRGyj2KwmieXFMc20SgFOloi0GwtV0VioasE/ZOOH
b9WgNPiodfIL1FwL1PDHXe/MzUU3nEoQSagj2bE9d/7jWRaP7hMRDkAbW7naUhhV
WToiLrVDMF/PmMGiZaJP5AMFUquDCVZw4adRKeKJieEAWkEMTY5iww/MyWmQzuE9
AVf0XrlNPFyzNuKFfNmh1JY//5LrlPthyRpb76OA1HDe3JlZOHhxemNcogbRtqTZ
4zLLYshuhDRsDaV0q9nS
=6ACI
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.2' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.2
1. Fixup of dpi and hdmi
2. Move panel connector to head
3. Add MT8188 dpi support
4. Add MT8195 AFBC support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221123234855.2485-1-chunkuang.hu@kernel.org
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/gpu/drm/mediatek/mtk_hdmi.c:1407:16: error: incompatible function pointer types initializing 'enum drm_mode_status (*)(struct drm_bridge *, const struct drm_display_info *, const struct drm_display_mode *)' with an expression of type 'int (struct drm_bridge *, const struct drm_display_info *, const struct drm_display_mode *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.mode_valid = mtk_hdmi_bridge_mode_valid,
^~~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
->mode_valid() in 'struct drm_bridge_funcs' expects a return type of
'enum drm_mode_status', not 'int'. Adjust the return type of
mtk_hdmi_bridge_mode_valid() to match the prototype's to resolve the
warning and CFI failure.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
[Why]
Some userspaces assume that the first connected connector is the "main"
display, which supposed to display, for example, the login screen.
For laptops, this should be the internal connector.
[How]
This patch calls drm_helper_move_panel_connectors_to_head() right before
crtc creation to ensure internal connectors are at the top of the
connector list.
Tested by ensuring the internal panels are at the top of the connector
list via modetest -c.
This patch does to mediatek what the following patch
https://www.spinics.net/lists/stable/msg590605.html
did for qualcomm.
Signed-off-by: Gil Dekel <gildekel@chromium.org>
Tested-by: Gil Dekel <gildekel@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Modify dpi power on/off sequence so that the first gpio operation will
take effect.
Fixes: 6bd4763fd5 ("drm/mediatek: set dpi pin mode to gpio low to avoid leakage current")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Initialize on-stack modes with drm_mode_init() to guarantee
no stack garbage in the list head.
Based on the following cocci script, with manual fixups:
@decl@
identifier M;
expression E;
@@
- struct drm_display_mode M = E;
+ struct drm_display_mode M;
@@
identifier decl.M;
expression decl.E;
statement S, S1;
@@
struct drm_display_mode M;
... when != S
+ drm_mode_init(&M, &E);
+
S1
@@
expression decl.E;
@@
- &*E
+ E
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107192545.9896-6-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the generic fbdev implementation into its own source and header
file. Adapt drivers. No functional changes, but some of the internal
helpers have been renamed to fit into the drm_fbdev_ naming scheme.
v3:
* rename drm_fbdev.{c,h} to drm_fbdev_generic.{c,h}
* rebase onto vmwgfx changes
* rebase onto xlnx changes
* fix include statements in amdgpu
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103151446.2638-22-tzimmermann@suse.de
core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU: simplified VBIF configuration
- cleanup CTL interfaces
- DSI: removed unused msm_display_dsc_config struct
- switch regulator calls to new API
- switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduces lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- Improve error and edge conditions handling
- Convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- Add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support
-----BEGIN PGP SIGNATURE-----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=u/MJ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff all over, some new AMD IP support and gang submit
support. i915 has further DG2 and Meteorlake pieces, and a bunch of
i915 display refactoring. msm has a shrinker rework. There are also a
bunch of conversions to use kunit.
This has two external pieces, some MEI changes needed for future Intel
discrete GPUs. These should be acked by Greg. There is also a cross
maintainer shared tree with some backlight rework from Hans in here.
Core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU:
simplified VBIF configuration
cleanup CTL interfaces
- DSI:
removed unused msm_display_dsc_config struct
switch regulator calls to new API
switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduce lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- improve error and edge conditions handling
- convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support"
* tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm: (1374 commits)
drm/amdkfd: Fix UBSAN shift-out-of-bounds warning
drm/amdkfd: Track unified memory when switching xnack mode
drm/amdgpu: Enable sram on vcn_4_0_2
drm/amdgpu: Enable VCN DPG for GC11_0_1
drm/msm: Fix build break with recent mm tree
drm/panel: simple: Use dev_err_probe() to simplify code
drm/panel: panel-edp: Use dev_err_probe() to simplify code
drm/panel: simple: Add Multi-Inno Technology MI0800FT-9
dt-bindings: display: simple: Add Multi-Inno Technology MI0800FT-9 panel
drm/amdgpu: correct the memcpy size for ip discovery firmware
drm/amdgpu: Skip put_reset_domain if it doesn't exist
drm/amdgpu: remove switch from amdgpu_gmc_noretry_set
drm/amdgpu: Fix mc_umc_status used uninitialized warning
drm/amd/display: Prevent OTG shutdown during PSR SU
drm/amdgpu: add page retirement handling for CPU RAS
drm/amdgpu: use RAS error address convert api in mca notifier
drm/amdgpu: support to convert dedicated umc mca address
drm/amdgpu: export umc error address convert interface
drm/amdgpu: fix sdma v4 init microcode error
drm/amd/display: fix array-bounds error in dc_stream_remove_writeback()
...
1. Drop of_gpio header
2. Remove the unneeded result
-----BEGIN PGP SIGNATURE-----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=yZ0D
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.1
1. Drop of_gpio header
2. Remove the unneeded result
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922234804.18557-1-chunkuang.hu@kernel.org
As the comment right before the mtk_dsi_stop() call advises,
mtk_dsi_stop() should only be called after
mtk_drm_crtc_atomic_disable(). That's because that function calls
drm_crtc_wait_one_vblank(), which requires the vblank irq to be enabled.
Previously mtk_dsi_stop(), being in mtk_dsi_poweroff() and guarded by a
refcount, would only be called at the end of
mtk_drm_crtc_atomic_disable(), through the call to mtk_crtc_ddp_hw_fini().
Commit cde7e2e35c ("drm/mediatek: Separate poweron/poweroff from
enable/disable and define new funcs") moved the mtk_dsi_stop() call to
mtk_output_dsi_disable(), causing it to be called before
mtk_drm_crtc_atomic_disable(), and consequently generating vblank
timeout warnings during suspend.
Move the mtk_dsi_stop() call back to mtk_dsi_poweroff() so that we have
a working vblank irq during mtk_drm_crtc_atomic_disable() and stop
getting vblank timeout warnings.
Fixes: cde7e2e35c ("drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Link: http://lists.infradead.org/pipermail/linux-mediatek/2022-August/046713.html
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mtk_dp_driver is only used in mtk_dp.c now, change it
to static.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913134929.1970187-1-yangyingliang@huawei.com
Some definitions in mtk_dp_reg.h are not used, so remove these
redundant codes.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916133821.27980-3-rex-bc.chen@mediatek.com
In order to improve human readability, reduce the indentation by
returning early if the dp/edp cable is not plugged in.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916133821.27980-2-rex-bc.chen@mediatek.com
The width and height arguments in the cmdq packet for mtk_dither_config()
are inverted. We fix the incorrect width and height for dither settings
in mtk_dither_config().
Fixes: 73d3724745 ("drm/mediatek: Adjust to the alphabetic order for mediatek-drm")
Co-developed-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220908141205.18256-1-allen-kh.cheng@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This patch adds audio support to the DP driver for MT8195 with up to 8
channels.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-11-rex-bc.chen@mediatek.com
From the DP spec 1.4a chapter 3.3, upstream devices should implement
HPD signal de-bouncing on an external connection.
A period of 100ms should be used to detect an HPD connect event.
To cover these cases, HPD de-bounce should be implemented only after
HPD low has been detected for at least 100ms.
Therefore,
1. If HPD is low (which means plugging out) for longer than 100ms:
we need to do de-bouncing (which means we need to wait for 100ms).
2. If HPD low is for less than 100ms:
we don't need to care about the de-bouncing.
In this patch, we start a 100ms timer and use a need_debounce boolean
to implement the feature.
Two cases when HPD is high:
1. If the timer is expired (>100ms):
- need_debounce is true.
- When HPD high (plugging event comes), need_debounce will be true
and then we need to do de-bouncing (wait for 100ms).
2. If the timer is not expired (<100ms):
- need_debounce is false.
- When HPD high (plugging event comes), need_debounce will be false
and no need to do de-bouncing.
HPD_______ __________________
| |<- 100ms ->
|____________|
<- 100ms ->
Without HPD de-bouncing, USB-C to HDMI Adapaters will not be detected.
The change has been successfully tested with the following devices:
- Dell Adapter - USB-C to HDMI
- Acer 1in1 HDMI dongle
- Ugreen 1in1 HDMI dongle
- innowatt HDMI + USB3 hub
- Acer 2in1 HDMI dongle
- Apple 3in1 HDMI dongle (A2119)
- J5Create 3in1 HDMI dongle (JAC379)
Tested-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-10-rex-bc.chen@mediatek.com
Add External DisplayPort support to the MT8195 eDP driver.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-9-rex-bc.chen@mediatek.com
It's not necessary to have a next_bridge for DP device, so we add this
patch to judge this.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-8-rex-bc.chen@mediatek.com
The calibration data formats of eDP and DP are different. We add
"const struct mtk_dp_efuse_fmt *efuse_fmt" to the device data to
define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-7-rex-bc.chen@mediatek.com
The smc commands of eDP and DP are different. We add smc_cmd to the
device data to define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-6-rex-bc.chen@mediatek.com
The bridge types of eDP and DP are different. We add device data to
this driver and add bridge_type to the device data to define them.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-5-rex-bc.chen@mediatek.com
This patch adds a embedded displayport driver for the MediaTek mt8195 SoC.
It supports the MT8195, the embedded DisplayPort units. It offers
DisplayPort 1.4 with up to 4 lanes.
The driver creates a child device for the phy. The child device will
never exist without the parent being active. As they are sharing a
register range, the parent passes a regmap pointer to the child so that
both can work with the same register range. The phy driver sets device
data that is read by the parent to get the phy device that can be used
to control the phy properties.
This driver is based on an initial version by
Jitao shi <jitao.shi@mediatek.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-4-rex-bc.chen@mediatek.com
Return the value drm_mode_config_helper_suspend() directly instead of
storing it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220825072335.228921-1-ye.xingchen@zte.com.cn/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add callbacks for atomic_destroy_state, atomic_duplicate_state and
atomic_reset to restore functionality of the DSI driver: this solves
vblank timeouts when another bridge is present in the chain.
Tested bridge chain: DSI <=> ANX7625 => aux-bus panel
Fixes: 7f6335c6a2 ("drm/mediatek: Modify dsi funcs to atomic operations")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220721172727.14624-1-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Rename "GEM CMA" helpers to "GEM DMA" helpers - considering the
hierarchy of APIs (mm/cma -> dma -> gem dma) calling them "GEM
DMA" seems to be more applicable.
Besides that, commit e57924d4ae ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(GEM)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(gem)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
# Rename all 'cma_obj's to 'dma_obj'.
for ff in $(grep -RiHl "cma_obj" $DIRS)
do
sed -i -E "s/cma_obj/dma_obj/g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "GEM CMA", but not "FB CMA".
Also drivers/gpu/drm/Makefile was fixed up manually after renaming
drm_gem_cma_helper.c to drm_gem_dma_helper.c.
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-4-dakr@redhat.com
Remove the include statement for drm_plane_helper.h from all the files
that don't need it. Althogh the header file is almost empty, many drivers
include it somewhere.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720083058.15371-5-tzimmermann@suse.de
The macro DRM_PLANE_HELPER_NO_SCALING is only useful with the interfaces
in drm_atomic_helper.h, but defined in drm_plane_helper.h. So half of
DRM includes the latter header file for using this macro. Move the macro
and remove the include statements.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720083058.15371-3-tzimmermann@suse.de
1. Add Mediatek Soc DRM (vdosys0) support for mt8195
2. Cooperate with DSI RX devices to modify dsi funcs and delay mipi high to cooperate with panel sequence
3. Add mt8186 dsi compatible and convert dsi_dtbinding to .yaml
4. Add MediaTek SoC DRM (vdosys1) support for mt8195
5. Add MT8195 dp_intf driver
-----BEGIN PGP SIGNATURE-----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=0Z1o
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.20' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.20
1. Add Mediatek Soc DRM (vdosys0) support for mt8195
2. Cooperate with DSI RX devices to modify dsi funcs and delay mipi high to cooperate with panel sequence
3. Add mt8186 dsi compatible and convert dsi_dtbinding to .yaml
4. Add MediaTek SoC DRM (vdosys1) support for mt8195
5. Add MT8195 dp_intf driver
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fix drm_edid.h include]
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220709142021.24260-1-chunkuang.hu@kernel.org
Dpintf is the displayport interface hardware unit. This unit is similar
to dpi and can reuse most of the code.
This patch adds support for mt8195-dpintf to this dpi driver. Main
differences are:
- 4 pixels for one iteration for dp_intf while dpi is 1 pixel for one
iteration.
- Input of dp_intf is two pixels per iteration.
- Some register contents differ slightly between the two components.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-6-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The quantity of output for one iteration could be different for dpi and
dp_intf. For dp_intf, it's 4 pixels for one iteration it's 1 pixel for one
iteration for dpi. Therefore, we add a new config "pixels_per_iter" to
control quantity of transferred pixels per iteration.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-5-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
MediaTek dpi supports direct connection to dpi panels while dp_intf does
not support. Therefore, add a config "support_direct_pin" to control this.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-3-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Dp_intf supports YUV422 as output format. In MT8195 Chrome project,
YUV422 output format is used for 4K resolution.
To support this, it is also needed to support color format transfer.
Color format transfer is a new feature for both dpi and dpintf of MT8195.
The input format could be RGB888 and output format for dp_intf should be
YUV422. Therefore, we add a mtk_dpi_matrix_sel() helper to update the
DPI_MATRIX_SET register depending on the color format.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-2-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.
Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.
v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com
Add flexibility by moving the yuv422 en bit to SoC specific config
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-12-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add flexibility by moving the swap shift value to SoC specific config.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-11-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add flexibility by moving the hvsize mask to SoC specific config.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-10-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add flexibility by moving the dimension mask to the SoC config
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-9-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The hardware design of dp_intf does not support input swap, so we add
a bit of flexibility to support SoCs without swap_input support.
We also add a warning message if the hardware is not supported and it
needs to swap input.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-8-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Dp_intf does not support CK/DE polarity because the polarity information
is not used for eDP and DP while dp_intf is only for eDP and DP.
Therefore, we add a bit of flexibility to support SoCs without CK/DE pol
support.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-7-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
For RGB colorimetry, CTA-861 support both limited and full range data
when receiving video with RGB color space.
We use drm_default_rgb_quant_range() to determine the correct setting.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-6-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Enabling the dpi too early causes glitches on screen.
Move the call to mtk_dpi_enable() at the end of the bridge_enable
callback to ensure everything is setup properly before enabling dpi.
Fixes: 9e629c17aa ("drm/mediatek: Add DPI sub driver")
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-16-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This driver will support dp_intf and there are many configs between dpi
and dp_intf. Therefore, we will add many configs in "struct mtk_dpi_conf".
To let this structure more readable, we add this kernel doc.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701035845.16458-4-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Make sure bridge_disable will be called before suspend by calling
drm_mode_config_helper_suspend() in .prepare callback.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220629190545.478113-1-hsinyi@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The compatible “mediatek,mt8192-disp-rdma” is being used for reading
the data into DMA for back-end panel driver in mt8192 but there is
no difference between mt8183 and mt8192 in rdma driver.
Remove compatible “mediatek,mt8192-disp-rdma” from the driver and
should use “mediatek,mt8183-disp-rdma” as fallback in 8192 DTS
according to the mediatek,rdma.yaml.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701090547.21429-2-allen-kh.cheng@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add plane color encoding information for color space conversion.
It's a preparation for adding support for mt8195 ovl_adaptor mdp_rdma
csc control.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220620091930.27797-10-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add merge async reset control in mtk_merge_stop. Async hw doesn't do self
reset on each sof signal(start of frame), so need to reset the async to
clear the hw status for the next merge start.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220620091930.27797-8-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add merge start/stop API for cmdq support. The ovl_adaptor merges
are configured with each drm plane update. Need to enable/disable
merge with cmdq making sure all the settings taken effect in the
same vblank.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220620091930.27797-6-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add merge new advance config API. The original merge API is
mtk_ddp_comp_funcs function prototype. The API interface parameters
cannot be modified, so add a new config API for extension. This is
the preparation for ovl_adaptor merge control.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220620091930.27797-5-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add MDP_RDMA driver for MT8195. MDP_RDMA is the DMA engine of
the ovl_adaptor component.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220620091930.27797-4-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
drm_crtc.h has no need for drm_blend.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_blend.h.
Quite a few placs do currently depend on drm_blend.h without
actually including it directly. All of those need to be fixed
up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220613200317.11305-4-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
drm_crtc.h has no need for drm_frambuffer.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_framebuffer.h.
Quite a few placs do currently depend on drm_framebuffer.h without
actually including it directly. All of those need to be fixed
up.
v2: Fix up msm some more
v2: Deal with ingenic and shmobile as well
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614095449.29311-1-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
In the dsi_enable function, mtk_dsi_rxtx_control is to
pull up the MIPI signal operation. Before dsi_disable,
MIPI should also be pulled down by writing a register
instead of disabling dsi.
If disable dsi without pulling the mipi signal low, the value of
the register will still maintain the setting of the mipi signal being
pulled high.
After resume, even if the mipi signal is not pulled high, it will still
be in the high state.
Fixes: 2e54c14e31 ("drm/mediatek: Add DSI sub driver")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-5-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
To comply with the panel sequence, hold the mipi signal to LP00 before
the dcs cmds transmission, and pull the mipi signal high from LP00 to
LP11 until the start of the dcs cmds transmission.
The normal panel timing is :
(1) pp1800 DC pull up
(2) avdd & avee AC pull high
(3) lcm_reset pull high -> pull low -> pull high
(4) Pull MIPI signal high (LP11) -> initial code -> send video data
(HS mode)
The power-off sequence is reversed.
If dsi is not in cmd mode, then dsi will pull the mipi signal high in
the mtk_output_dsi_enable function. The delay in lane_ready func is
the reaction time of dsi_rx after pulling up the mipi signal.
Fixes: 2dd8075d21 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-4-git-send-email-xinlei.lee@mediatek.com/
Cc: <stable@vger.kernel.org> # 5.10.x: 7f6335c6a2: drm/mediatek: Modify dsi funcs to atomic operations
Cc: <stable@vger.kernel.org> # 5.10.x: cde7e2e35c: drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In order to match the changes of "Use the drm_panel_bridge API",
the poweron/poweroff of dsi is extracted from enable/disable and
defined as new funcs (atomic_pre_enable/atomic_post_disable).
Since dsi_poweron is moved from dsi_enable to pre_enable function, in
order to avoid poweron failure, the operation of dsi register fails to
cause bus hang. Therefore, the protection mechanism is added to the
dsi_enable function.
Fixes: 2dd8075d21 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-3-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Because mt8195 vdosys0 has 2 DITHER components,
so the suffix 0 need to be added to DDP_COMPONENT_DITHER.
Then DITHER enum will become:
DDP_COMPONENT_DITHER0 and DDP_COMPONENT_DITHER1.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220526102126.19756-5-jason-jh.lin@mediatek.com/
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
1. Add driver data of mt8195 vdosys0 to mediatek-drm and the sub driver.
2. Add get driver data function to identify which vdosys by io_start.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220526102126.19756-4-jason-jh.lin@mediatek.com/
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
DSC is designed for real-time systems with real-time compression,
transmission, decompression and display.
The DSC standard is a specification of the algorithms used for
compressing and decompressing image display streams, including
the specification of the syntax and semantics of the compressed
video bit stream.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220526102126.19756-2-jason-jh.lin@mediatek.com/
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
1. Add display support for MT8186
2. Miscellaneous refinement and fixup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C1nR
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.19' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.19
1. Add display support for MT8186
2. Miscellaneous refinement and fixup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1651702965-23630-1-git-send-email-chunkuang.hu@kernel.org
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warning:
./drivers/gpu/drm/mediatek/mtk_dsi.c:1092:2-9: line 1092 is redundant
because platform_get_irq() already prints an error
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220224012318.84935-1-yang.lee@linux.alibaba.com/
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mt8183 gamma module usage is different with before soc,
gamma odd(index start from 0) lut value set to hardware
register should be
the difference of current lut value with last lut value.
for example, chrome os user space set lut
like this(only r chanel for example):
2 4 6 8 10 12.
1) mt8183 gamma driver should set the gamma lut to hardware
register like this:
2 [2] 6 [2] 10 [2]
the value with [] is the difference value
2)gamma hardware process display data with original lut
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220428085829.15855-2-yongqiang.niu@mediatek.com/
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.corp-partner.google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The configuration for mt8192 was incorrectly using the output formats
from mt8173. Since the output formats for mt8192 are instead the same
ones as for mt8183, which require two bus samples per pixel, the
pixelclock and DDR edge setting were misconfigured. This made external
displays unable to show the image.
Fix the issue by correcting the output format for mt8192 to be the same
as for mt8183, fixing the usage of external displays for mt8192.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220408013950.674477-1-nfraprado@collabora.com/
Fixes: be63f6e860 ("drm/mediatek: dpi: Add output bus formats to driver data")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add mmsys driver data and compatible for MT8186 in mtk_drm_drv.c.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220421051218.8652-2-rex-bc.chen@mediatek.com/
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In current implementation, mtk_cec_mask() writes val into target register
and ignores the mask. After talking to our hdmi experts, mtk_cec_mask()
should read a register, clean only mask bits, and update (val | mask) bits
to the register.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220315232301.2434-1-miles.chen@mediatek.com/
Fixes: 8f83f26891 ("drm/mediatek: Add HDMI support")
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Zhiqiang Lin <zhiqiang.lin@mediatek.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
When support for MT8192 was added, the DPI device was not added to the
list of components to look for. This causes the secondary display
pipeline to not be able to fully bind, and the DRM driver subsequently
defers probing.
Add the DPI device compatible to list of DPI components to fix this.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220225032754.140168-1-wenst@chromium.org/
Fixes: 01365f549c ("drm/mediatek: Add support for Mediatek SoC MT8192")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
We encountered a kernel panic issue that callback data will be NULL when
it's using in ovl irq handler. There is a timing issue between
mtk_disp_ovl_irq_handler() and mtk_ovl_disable_vblank().
To resolve this issue, we use the flow to register/unregister vblank cb:
- Register callback function and callback data when crtc creates.
- Unregister callback function and callback data when crtc destroies.
With this solution, we can assure callback data will not be NULL when
vblank is disable.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220321072320.15019-1-rex-bc.chen@mediatek.com/
Fixes: 9b0704988b ("drm/mediatek: Register vblank callback function")
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Optimize mtk_drm_crtc_duplicate_state() by switching from kzalloc() to
kmalloc(): the only variable of this struct that gets checked in other
functions is `pending_config`, but if that's set to false, then all of
the remaining variables will only ever be set, but not read - so, also
set `pending_config` to false.
This saves us some small overhead.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220118133759.112458-2-angelogioacchino.delregno@collabora.com/
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
devm_drm_of_get_bridge is capable of looking up the downstream
bridge and panel and trying to add a panel bridge if the panel
is found.
Replace explicit finding calls with devm_drm_of_get_bridge.
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331154503.66054-3-jagan@amarulasolutions.com
Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
There will be a merge conflict in drivers/power/supply/ab8500_chargalg.c
with your tree, the merge conflict should be easy (take all the
changes).
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG6PA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylMFwCfSIyAU4oLEgj+/Rfmx4o45cAVIWMAnit3zbdU
wUUCGqKcOnTJEcW6dMPh
=1VVi
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
Documentation: update stable review cycle documentation
drivers/base/dd.c : Remove the initial value of the global variable
Documentation: update stable tree link
Documentation: add link to stable release candidate tree
devres: fix typos in comments
Documentation: add note block surrounding security patch note
samples/kobject: Use sysfs_emit instead of sprintf
base: soc: Make soc_device_match() simpler and easier to read
driver core: dd: fix return value of __setup handler
driver core: Refactor sysfs and drv/bus remove hooks
driver core: Refactor multiple copies of device cleanup
scripts: get_abi.pl: Fix typo in help message
kernfs: fix typos in comments
kernfs: remove unneeded #if 0 guard
ALSA: hda/realtek: Make use of the helper component_compare_dev_name
video: omapfb: dss: Make use of the helper component_compare_dev
power: supply: ab8500: Make use of the helper component_compare_dev
ASoC: codecs: wcd938x: Make use of the helper component_compare/release_of
iommu/mediatek: Make use of the helper component_compare/release_of
drm: of: Make use of the helper component_release_of
...
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device
-----BEGIN PGP SIGNATURE-----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=uRsT
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of work all over, Intel improving DG2 support, amdkfd CRIU
support, msm new hw support, and faster fbdev support.
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device"
* tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm: (1529 commits)
drm/i915/display: Do not re-enable PSR after it was marked as not reliable
drm/i915/display: Fix HPD short pulse handling for eDP
drm/amdgpu: Use drm_mode_copy()
drm/radeon: Use drm_mode_copy()
drm/amdgpu: Use ternary operator in `vcn_v1_0_start()`
drm/amdgpu: Remove pointless on stack mode copies
drm/amd/pm: fix indenting in __smu_cmn_reg_print_error()
drm/amdgpu/dc: fix typos in comments
drm/amdgpu: fix typos in comments
drm/amd/pm: fix typos in comments
drm/amdgpu: Add stolen reserved memory for MI25 SRIOV.
drm/amdgpu: Merge get_reserved_allocation to get_vbios_allocations.
drm/amdkfd: evict svm bo worker handle error
drm/amdgpu/vcn: fix vcn ring test failure in igt reload test
drm/amdgpu: only allow secure submission on rings which support that
drm/amdgpu: fixed the warnings reported by kernel test robot
drm/amd/display: 3.2.177
drm/amd/display: [FW Promotion] Release 0.0.108.0
drm/amd/display: Add save/restore PANEL_PWRSEQ_REF_DIV2
drm/amd/display: Wait for hubp read line for Pollock
...
-----BEGIN PGP SIGNATURE-----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=Bc0l
-----END PGP SIGNATURE-----
Merge tag 'media/v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a major reorg at platform Kconfig/Makefile files, organizing them per
vendor. The other media Kconfig/Makefile files also sorted
- New sensor drivers: hi847, isl7998x, ov08d10
- New Amphion vpu decoder stateful driver
- New Atmel microchip csi2dc driver
- tegra-vde driver promoted from staging
- atomisp: some fixes for it to work on BYT
- imx7-mipi-csis driver promoted from staging and renamed
- camss driver got initial support for VFE hardware version Titan 480
- mtk-vcodec has gained support for MT8192
- lots of driver changes, fixes and improvements
* tag 'media/v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (417 commits)
media: nxp: Restrict VIDEO_IMX_MIPI_CSIS to ARCH_MXC or COMPILE_TEST
media: amphion: cleanup media device if register it fail
media: amphion: fix some issues to improve robust
media: amphion: fix some error related with undefined reference to __divdi3
media: amphion: fix an issue that using pm_runtime_get_sync incorrectly
media: vidtv: use vfree() for memory allocated with vzalloc()
media: m5mols/m5mols.h: document new reset field
media: pixfmt-yuv-planar.rst: fix PIX_FMT labels
media: platform: Remove unnecessary print function dev_err()
media: amphion: Add missing of_node_put() in vpu_core_parse_dt()
media: mtk-vcodec: Add missing of_node_put() in mtk_vdec_hw_prob_done()
media: platform: amphion: Fix build error without MAILBOX
media: spi: Kconfig: Place SPI drivers on a single menu
media: i2c: Kconfig: move camera drivers to the top
media: atomisp: fix bad usage at error handling logic
media: platform: rename mediatek/mtk-jpeg/ to mediatek/jpeg/
media: media/*/Kconfig: sort entries
media: Kconfig: cleanup VIDEO_DEV dependencies
media: platform/*/Kconfig: make manufacturer menus more uniform
media: platform: Create vendor/{Makefile,Kconfig} files
...
Some DSI RX devices (for example, anx7625) require last alignment of
packets on all lanes after each row of data is sent.
Otherwise, there will be some issues of shift or scroll for screen.
Take horizontal_sync_active_byte for a example,
we roundup the HSA packet data to lane number, and the subtraction of 2
is the packet data value added by the roundup operation, making the
long packets are integer multiples of lane number.
This value (2) varies with the lane number, and that is the reason we
do this operation when the lane number is 4.
In the previous operation of function "mtk_dsi_config_vdo_timing",
the length of HSA and HFP data packets has been adjusted to an
integration multiple of lane number.
Since the number of RGB data packets cannot be guaranteed to be an
integer multiple of lane number, we modify the data packet length of
HBP so that the number of HBP + RGB is equal to the lane number.
So after sending a line of data (HSA + HBP + RGB + HFP), the data
lanes are aligned.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-3-rex-bc.chen@mediatek.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIb/PEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGugMH/R8icwG5gOjAuxBr
fuz9032ECVFS36Cy3ps9Eqgf5EdS4G6yz3joM4aNtp4B7e5FzI9lzBaHS8OAguNL
y7puFtBr9CywsnniJumZzciB9pEHmF/yyEKfMlRZA3JsRfLDacFstETp+duJnXoA
+s49IWsy1ot5zoherhDXcFLqDoFhLVU4hYwE1xpLpW/cllqmSnW8SDZMtWW1Ui/B
Of7zqINR4zBMmRjP4ymGq/ZrPWlFyWLdtOo0xxVoAQkeMgm33kfaaeGzfyK25FqR
JDGUZ7lkKvwz3PYh2hqJ7dc5K+vhJ18I+F1UmOiL6QAAUF/k8jq7i3Qaf6MKqh2Z
2v+A5k0=
=Hiar
-----END PGP SIGNATURE-----
Backmerge tag 'v5.17-rc6' into drm-next
This backmerges v5.17-rc6 so I can merge some amdgpu and some tegra changes on top.
Signed-off-by: Dave Airlie <airlied@redhat.com>
1. Transfer display binding document to yaml format.
2. Add mt8195 display device binding.
3. Allow commands to be sent during video mode.
4. Add wait_for_event for crtc disable by cmdq.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HgGH
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.18' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.18
1. Transfer display binding document to yaml format.
2. Add mt8195 display device binding.
3. Allow commands to be sent during video mode.
4. Add wait_for_event for crtc disable by cmdq.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1645934583-2018-1-git-send-email-chunkuang.hu@kernel.org
mtk_drm_crtc_atomic_disable will send an async cmd to cmdq driver,
so it may not finish when cmdq_suspend is called sometimes.
Add wait_for_event after sending async disable plane cmd to make
sure the lastest cmd is done before cmdq_suspend.
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20211202064039.20797-2-jason-jh.lin@mediatek.com/
Use the common compare helper from component.
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20220214060819.7334-8-yong.wu@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
-----BEGIN PGP SIGNATURE-----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=HuwD
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-02-23' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
Mipi dsi panel drivers can use mipi_dsi_dcs_{set,get}_display_brightness()
to request backlight changes.
This can be done during panel initialization (dsi is in command mode)
or afterwards (dsi is in Video Mode).
When the DSI is in Video Mode, all commands are rejected.
Detect current DSI mode in mtk_dsi_host_transfer() and switch modes
temporarily to allow commands to be sent.
Signed-off-by: Julien STEPHAN <jstephan@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
DRM bridge drivers are now attaching their DSI device at probe time,
which requires us to register our DSI host in order to let the bridge
to probe: this recently started producing an endless -EPROBE_DEFER
loop on some machines that are using external bridges, like the
parade-ps8640, found on the ACER Chromebook R13.
Now that the DSI hosts/devices probe sequence is documented, we can
do adjustments to the mtk_dsi driver as to both fix now and make sure
to avoid this situation in the future: for this, following what is
documented in drm_bridge.c, move the mtk_dsi component_add() to the
mtk_dsi_ops.attach callback and delete it in the detach callback;
keeping in mind that we are registering a drm_bridge for our DSI,
which is only used/attached if the DSI Host is bound, it wouldn't
make sense to keep adding our bridge at probe time (as it would
be useless to have it if mtk_dsi_ops.attach() fails!), so also move
that one to the dsi host attach function (and remove it in detach).
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Rename struct dma_buf_map to struct iosys_map and corresponding APIs.
Over time dma-buf-map grew up to more functionality than the one used by
dma-buf: in fact it's just a shim layer to abstract system memory, that
can be accessed via regular load and store, from IO memory that needs to
be acessed via arch helpers.
The idea is to extend this API so it can fulfill other needs, internal
to a single driver. Example: in the i915 driver it's desired to share
the implementation for integrated graphics, which uses mostly system
memory, with discrete graphics, which may need to access IO memory.
The conversion was mostly done with the following semantic patch:
@r1@
@@
- struct dma_buf_map
+ struct iosys_map
@r2@
@@
(
- DMA_BUF_MAP_INIT_VADDR
+ IOSYS_MAP_INIT_VADDR
|
- dma_buf_map_set_vaddr
+ iosys_map_set_vaddr
|
- dma_buf_map_set_vaddr_iomem
+ iosys_map_set_vaddr_iomem
|
- dma_buf_map_is_equal
+ iosys_map_is_equal
|
- dma_buf_map_is_null
+ iosys_map_is_null
|
- dma_buf_map_is_set
+ iosys_map_is_set
|
- dma_buf_map_clear
+ iosys_map_clear
|
- dma_buf_map_memcpy_to
+ iosys_map_memcpy_to
|
- dma_buf_map_incr
+ iosys_map_incr
)
@@
@@
- #include <linux/dma-buf-map.h>
+ #include <linux/iosys-map.h>
Then some files had their includes adjusted and some comments were
update to remove mentions to dma-buf-map.
Since this is not specific to dma-buf anymore, move the documentation to
the "Bus-Independent Device Accesses" section.
v2:
- Squash patches
v3:
- Fix wrong removal of dma-buf.h from MAINTAINERS
- Move documentation from dma-buf.rst to device-io.rst
v4:
- Change documentation title and level
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204170541.829227-1-lucas.demarchi@intel.com
First backmerge into drm-misc-next. Required for more helpers backmerged,
and to pull in 5.17 (rc2).
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
MediaTek IOMMU has already added the device_link between the consumer
and smi-larb device. If the drm device calls the pm_runtime_get_sync,
the smi-larb's pm_runtime_get_sync also be called automatically.
CC: CK Hu <ck.hu@mediatek.com>
CC: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de> # BPI-R2/MT7623
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Prepare for smi cleaning up "mediatek,larb".
Display use the dispsys device to call pm_rumtime_get_sync before.
This patch add pm_runtime_xx with ovl and rdma device whose nodes has
"iommus" property, then display could help pm_runtime_get for smi via
ovl or rdma device.
(Yong: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync)
CC: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de> # BPI-R2/MT7623
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
According to disable Documentation/admin-guide/kernel-parameters.txt, this
parameter can be used to disable kernel modesetting.
DRM drivers will not perform display-mode changes or accelerated rendering
and only the system framebuffer will be available if it was set-up.
But only a few DRM drivers currently check for nomodeset, make this driver
to also support the command line parameter.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211217003752.3946210-29-javierm@redhat.com
core:
- add privacy screen support
- move nomodeset option into drm subsystem
- clean up nomodeset handling in drivers
- make drm_irq.c legacy
- fix stack_depot name conflicts
- remove DMA_BUF_SET_NAME ioctl restrictions
- sysfs: send hotplug event
- replace several DRM_* logging macros with drm_*
- move hashtable to legacy code
- add error return from gem_create_object
- cma-helper: improve interfaces, drop CONFIG_DRM_KMS_CMA_HELPER
- kernel.h related include cleanups
- support XRGB2101010 source buffers
ttm:
- don't include drm hashtable
- stop pruning fences after wait
- documentation updates
dma-buf:
- add dma_resv selftest
- add debugfs helpers
- remove dma_resv_get_excl_unlocked
- documentation
- make fences mandatory in dma_resv_add_excl_fence
dp:
- add link training delay helpers
gem:
- link shmem/cma helpers into separate modules
- use dma_resv iteratior
- import dma-buf namespace into gem helper modules
scheduler:
- fence grab fix
- lockdep fixes
bridge:
- switch to managed MIPI DSI helpers
- register and attach during probe fixes
- convert to YAML in several places.
panel:
- add bunch of new panesl
simpledrm:
- support FB_DAMAGE_CLIPS
- support virtual screen sizes
- add Apple M1 support
amdgpu:
- enable seamless boot for DCN 3.01
- runtime PM fixes
- use drm_kms_helper_connector_hotplug_event
- get all fences at once
- use generic drm fb helpers
- PSR/DPCD/LTTPR/DSC/PM/RAS/OLED/SRIOV fixes
- add smart trace buffer (STB) for supported GPUs
- display debugfs entries
- new SMU debug option
- Documentation update
amdkfd:
- IP discovery enumeration refactor
- interface between driver fixes
- SVM fixes
- kfd uapi header to define some sysfs bitfields.
i915:
- support VESA panel backlights
- enable ADL-P by default
- add eDP privacy screen support
- add Raptor Lake S (RPL-S) support
- DG2 page table support
- lots of GuC/HuC fw refactoring
- refactored i915->gt interfaces
- CD clock squashing support
- enable 10-bit gamma support
- update ADL-P DMC fw to v2.14
- enable runtime PM autosuspend by default
- ADL-P DSI support
- per-lane DP drive settings for ICL+
- add support for pipe C/D DMC firmware
- Atomic gamma LUT updates
- remove CCS FB stride restrictions on ADL-P
- VRR platform support for display 11
- add support for display audio codec keepalive
- lots of display refactoring
- fix runtime PM handling during PXP suspend
- improved eviction performance with async TTM moves
- async VMA unbinding improvements
- VMA locking refactoring
- improved error capture robustness
- use per device iommu checks
- drop bits stealing from i915_sw_fence function ptr
- remove dma_resv_prune
- add IC cache invalidation on DG2
nouveau:
- crc fixes
- validate LUTs in atomic check
- set HDMI AVI RGB quant to full
tegra:
- buffer objects reworks for dma-buf compat
- NVDEC driver uAPI support
- power management improvements
etnaviv:
- IOMMU enabled system support
- fix > 4GB command buffer mapping
- close a DoS vector
- fix spurious GPU resets
ast:
- fix i2c initialization
rcar-du:
- DSI output support
exynos:
- replace legacy gpio interface
- implement generic GEM object mmap
msm:
- dpu plane state cleanup in prep for multirect
- dpu debugfs cleanups
- dp support for sc7280
- a506 support
- removal of struct_mutex
- remove old eDP sub-driver
anx7625:
- support MIPI DSI input
- support HDMI audio
- fix reading EDID
lvds:
- fix bridge DT bindings
megachips:
- probe both bridges before registering
dw-hdmi:
- allow interlace on bridge
ps8640:
- enable runtime PM
- support aux-bus
tx358768:
- enable reference clock
- add pulse mode support
ti-sn65dsi86:
- use regmap bulk write
- add PWM support
etnaviv:
- get all fences at once
gma500:
- gem object cleanups
kmb:
- enable fb console
radeon:
- use dma_resv_wait_timeout
rockchip:
- add DSP hold timeout
- suspend/resume fixes
- PLL clock fixes
- implement mmap in GEM object functions
- use generic fbdev emulation
sun4i:
- use CMA helpers without vmap support
vc4:
- fix HDMI-CEC hang with display is off
- power on HDMI controller while disabling
- support 4K@60Hz modes
- support 10-bit YUV 4:2:0 output
vmwgfx:
- fix leak on probe errors
- fail probing on broken hosts
- new placement for MOB page tables
- hide internal BOs from userspace
- implement GEM support
- implement GL 4.3 support
virtio:
- overflow fixes
xen:
- implement mmap as GEM object function
omapdrm:
- fix scatterlist export
- support virtual planes
mediatek:
- MT8192 support
- CMDQ refinement
-----BEGIN PGP SIGNATURE-----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=MByd
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-01-07' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights are support for privacy screens found in new laptops, a
bunch of nomodeset refactoring, and i915 enables ADL-P systems by
default, while starting to add RPL-S support.
vmwgfx adds GEM and support for OpenGL 4.3 features in userspace.
Lots of internal refactorings around dma reservations, and lots of
driver refactoring as well.
Summary:
core:
- add privacy screen support
- move nomodeset option into drm subsystem
- clean up nomodeset handling in drivers
- make drm_irq.c legacy
- fix stack_depot name conflicts
- remove DMA_BUF_SET_NAME ioctl restrictions
- sysfs: send hotplug event
- replace several DRM_* logging macros with drm_*
- move hashtable to legacy code
- add error return from gem_create_object
- cma-helper: improve interfaces, drop CONFIG_DRM_KMS_CMA_HELPER
- kernel.h related include cleanups
- support XRGB2101010 source buffers
ttm:
- don't include drm hashtable
- stop pruning fences after wait
- documentation updates
dma-buf:
- add dma_resv selftest
- add debugfs helpers
- remove dma_resv_get_excl_unlocked
- documentation
- make fences mandatory in dma_resv_add_excl_fence
dp:
- add link training delay helpers
gem:
- link shmem/cma helpers into separate modules
- use dma_resv iteratior
- import dma-buf namespace into gem helper modules
scheduler:
- fence grab fix
- lockdep fixes
bridge:
- switch to managed MIPI DSI helpers
- register and attach during probe fixes
- convert to YAML in several places.
panel:
- add bunch of new panesl
simpledrm:
- support FB_DAMAGE_CLIPS
- support virtual screen sizes
- add Apple M1 support
amdgpu:
- enable seamless boot for DCN 3.01
- runtime PM fixes
- use drm_kms_helper_connector_hotplug_event
- get all fences at once
- use generic drm fb helpers
- PSR/DPCD/LTTPR/DSC/PM/RAS/OLED/SRIOV fixes
- add smart trace buffer (STB) for supported GPUs
- display debugfs entries
- new SMU debug option
- Documentation update
amdkfd:
- IP discovery enumeration refactor
- interface between driver fixes
- SVM fixes
- kfd uapi header to define some sysfs bitfields.
i915:
- support VESA panel backlights
- enable ADL-P by default
- add eDP privacy screen support
- add Raptor Lake S (RPL-S) support
- DG2 page table support
- lots of GuC/HuC fw refactoring
- refactored i915->gt interfaces
- CD clock squashing support
- enable 10-bit gamma support
- update ADL-P DMC fw to v2.14
- enable runtime PM autosuspend by default
- ADL-P DSI support
- per-lane DP drive settings for ICL+
- add support for pipe C/D DMC firmware
- Atomic gamma LUT updates
- remove CCS FB stride restrictions on ADL-P
- VRR platform support for display 11
- add support for display audio codec keepalive
- lots of display refactoring
- fix runtime PM handling during PXP suspend
- improved eviction performance with async TTM moves
- async VMA unbinding improvements
- VMA locking refactoring
- improved error capture robustness
- use per device iommu checks
- drop bits stealing from i915_sw_fence function ptr
- remove dma_resv_prune
- add IC cache invalidation on DG2
nouveau:
- crc fixes
- validate LUTs in atomic check
- set HDMI AVI RGB quant to full
tegra:
- buffer objects reworks for dma-buf compat
- NVDEC driver uAPI support
- power management improvements
etnaviv:
- IOMMU enabled system support
- fix > 4GB command buffer mapping
- close a DoS vector
- fix spurious GPU resets
ast:
- fix i2c initialization
rcar-du:
- DSI output support
exynos:
- replace legacy gpio interface
- implement generic GEM object mmap
msm:
- dpu plane state cleanup in prep for multirect
- dpu debugfs cleanups
- dp support for sc7280
- a506 support
- removal of struct_mutex
- remove old eDP sub-driver
anx7625:
- support MIPI DSI input
- support HDMI audio
- fix reading EDID
lvds:
- fix bridge DT bindings
megachips:
- probe both bridges before registering
dw-hdmi:
- allow interlace on bridge
ps8640:
- enable runtime PM
- support aux-bus
tx358768:
- enable reference clock
- add pulse mode support
ti-sn65dsi86:
- use regmap bulk write
- add PWM support
etnaviv:
- get all fences at once
gma500:
- gem object cleanups
kmb:
- enable fb console
radeon:
- use dma_resv_wait_timeout
rockchip:
- add DSP hold timeout
- suspend/resume fixes
- PLL clock fixes
- implement mmap in GEM object functions
- use generic fbdev emulation
sun4i:
- use CMA helpers without vmap support
vc4:
- fix HDMI-CEC hang with display is off
- power on HDMI controller while disabling
- support 4K@60Hz modes
- support 10-bit YUV 4:2:0 output
vmwgfx:
- fix leak on probe errors
- fail probing on broken hosts
- new placement for MOB page tables
- hide internal BOs from userspace
- implement GEM support
- implement GL 4.3 support
virtio:
- overflow fixes
xen:
- implement mmap as GEM object function
omapdrm:
- fix scatterlist export
- support virtual planes
mediatek:
- MT8192 support
- CMDQ refinement"
* tag 'drm-next-2022-01-07' of git://anongit.freedesktop.org/drm/drm: (1241 commits)
drm/amdgpu: no DC support for headless chips
drm/amd/display: fix dereference before NULL check
drm/amdgpu: always reset the asic in suspend (v2)
drm/amdgpu: put SMU into proper state on runpm suspending for BOCO capable platform
drm/amd/display: Fix the uninitialized variable in enable_stream_features()
drm/amdgpu: fix runpm documentation
amdgpu/pm: Make sysfs pm attributes as read-only for VFs
drm/amdgpu: save error count in RAS poison handler
drm/amdgpu: drop redundant semicolon
drm/amd/display: get and restore link res map
drm/amd/display: support dynamic HPO DP link encoder allocation
drm/amd/display: access hpo dp link encoder only through link resource
drm/amd/display: populate link res in both detection and validation
drm/amd/display: define link res and make it accessible to all link interfaces
drm/amd/display: 3.2.167
drm/amd/display: [FW Promotion] Release 0.0.98
drm/amd/display: Undo ODM combine
drm/amd/display: Add reg defs for DCN303
drm/amd/display: Changed pipe split policy to allow for multi-display pipe split
drm/amd/display: Set optimize_pwr_state for DCN31
...
At the reset hook, call __drm_atomic_helper_plane_reset which is
called at the initialization of the plane and sets the default value of
rotation on all planes to DRM_MODE_ROTATE_0 which is equal to 1.
Tested on Jacuzzi (MTK).
Resolves IGT@kms_properties@plane-properties-{legacy,atomic}
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In commit 41ca9caaae
("drm/mediatek: hdmi: Add check for CEA modes only") a check
for CEA modes was added to function mtk_hdmi_bridge_mode_valid()
in order to address possible issues on MT8167;
moreover, with commit c91026a938
("drm/mediatek: hdmi: Add optional limit on maximal HDMI mode clock")
another similar check was introduced.
Unfortunately though, at the time of writing, MT8173 does not provide
any mtk_hdmi_conf structure and this is crashing the kernel with NULL
pointer upon entering mtk_hdmi_bridge_mode_valid(), which happens as
soon as a HDMI cable gets plugged in.
To fix this regression, add a NULL pointer check for hdmi->conf in the
said function, restoring HDMI functionality and avoiding NULL pointer
kernel panics.
Fixes: 41ca9caaae ("drm/mediatek: hdmi: Add check for CEA modes only")
Fixes: c91026a938 ("drm/mediatek: hdmi: Add optional limit on maximal HDMI mode clock")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Adjust to the alphabetic order for the define, function, struct
and array in mediatek-drm driver
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add DISP_REG prefix for the define of register offset to
make the difference from the define of register value.
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Remove the unsed define in mtk_drm_ddp_comp.c
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In cmdq mode, packet may be flushed before it is executed, so
the pending flag should be cleared after cmdq packet is done.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
One mtk_crtc need just one cmdq_handle, so add one cmdq_handle
in mtk_crtc to prevent frequently allocation and free of
cmdq_handle.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
CMDQ is used to update display register in vblank period, so
it should be execute in next 2 vblank. One vblank interrupt
before send message (occasionally) and one vblank interrupt
after cmdq done. If it fail to execute in next 3 vblank,
tiemout happen.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
In mailbox rx_callback, it pass struct mbox_client to callback
function, but it could not map back to mtk_drm_crtc instance
because struct cmdq_client use a pointer to struct mbox_client:
struct cmdq_client {
struct mbox_client client;
struct mbox_chan *chan;
};
struct mtk_drm_crtc {
/* client instance data */
struct cmdq_client *cmdq_client;
};
so remove the pointer of struct cmdq_client and let mtk_drm_crtc
instance define cmdq_client as:
struct mtk_drm_crtc {
/* client instance data */
struct cmdq_client cmdq_client;
};
and in rx_callback function, use struct mbox_client to get
struct mtk_drm_crtc.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
rx_callback is a standard mailbox callback mechanism and could cover the
function of proprietary cmdq_task_cb, so use the standard one instead of
the proprietary one.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Add support for Mediatek SoC MT8192
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
These are all the driver updates for SoC specific drivers. There
are a couple of subsystems with individual maintainers picking up
their patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this
tree this time. There are only minor changes, but they depend
on other tegra driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process.
This depends on a small sound driver change that is included
here as well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains
a mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for
the "Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed
BMCs, something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better suspend/resume
support
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
allwinner, broadcom, and omap.
-----BEGIN PGP SIGNATURE-----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=tUuj
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
This reverts commit f4be17cd5b.
Commit c1ec54b7b5
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This reverts commit 8cdcb36534.
Commit c1ec54b7b5
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This reverts commit bc9241be73.
Commit c1ec54b7b5
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This reverts commit 9efb16c2fd.
Commit c1ec54b7b5
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reset dsi0 HW to default when power on. This prevents to have different
settingis between the bootloader and the kernel.
As not all Mediatek boards have the reset consumer configured in their
board description, also is not needed on all of them, the reset is optional,
so the change is compatible with all boards.
Cc: Jitao Shi <jitao.shi@mediatek.com>
Suggested-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20210930103105.v4.7.Idbb4727ddf00ba2fe796b630906baff10d994d89@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
core:
- extract i915 eDP backlight into core
- DP aux bus support
- drm_device.irq_enabled removed
- port drivers to native irq interfaces
- export gem shadow plane handling for vgem
- print proper driver name in framebuffer registration
- driver fixes for implicit fencing rules
- ARM fixed rate compression modifier added
- updated fb damage handling
- rmfb ioctl logging/docs
- drop drm_gem_object_put_locked
- define DRM_FORMAT_MAX_PLANES
- add gem fb vmap/vunmap helpers
- add lockdep_assert(once) helpers
- mark drm irq midlayer as legacy
- use offset adjusted bo mapping conversion
vgaarb:
- cleanups
fbdev:
- extend efifb handling to all arches
- div by 0 fixes for multiple drivers
udmabuf:
- add hugepage mapping support
dma-buf:
- non-dynamic exporter fixups
- document implicit fencing rules
amdgpu:
- Initial Cyan Skillfish support
- switch virtual DCE over to vkms based atomic
- VCN/JPEG power down fixes
- NAVI PCIE link handling fixes
- AMD HDMI freesync fixes
- Yellow Carp + Beige Goby fixes
- Clockgating/S0ix/SMU/EEPROM fixes
- embed hw fence in job
- rework dma-resv handling
- ensure eviction to system ram
amdkfd:
- uapi: SVM address range query added
- sysfs leak fix
- GPUVM TLB optimizations
- vmfault/migration counters
i915:
- Enable JSL and EHL by default
- preliminary XeHP/DG2 support
- remove all CNL support (never shipped)
- move to TTM for discrete memory support
- allow mixed object mmap handling
- GEM uAPI spring cleaning
- add I915_MMAP_OBJECT_FIXED
- reinstate ADL-P mmap ioctls
- drop a bunch of unused by userspace features
- disable and remove GPU relocations
- revert some i915 misfeatures
- major refactoring of GuC for Gen11+
- execbuffer object locking separate step
- reject caching/set-domain on discrete
- Enable pipe DMC loading on XE-LPD and ADL-P
- add PSF GV point support
- Refactor and fix DDI buffer translations
- Clean up FBC CFB allocation code
- Finish INTEL_GEN() and friends macro conversions
nouveau:
- add eDP backlight support
- implicit fence fix
msm:
- a680/7c3 support
- drm/scheduler conversion
panfrost:
- rework GPU reset
virtio:
- fix fencing for planes
ast:
- add detect support
bochs:
- move to tiny GPU driver
vc4:
- use hotplug irqs
- HDMI codec support
vmwgfx:
- use internal vmware device headers
ingenic:
- demidlayering irq
rcar-du:
- shutdown fixes
- convert to bridge connector helpers
zynqmp-dsub:
- misc fixes
mgag200:
- convert PLL handling to atomic
mediatek:
- MT8133 AAL support
- gem mmap object support
- MT8167 support
etnaviv:
- NXP Layerscape LS1028A SoC support
- GEM mmap cleanups
tegra:
- new user API
exynos:
- missing unlock fix
- build warning fix
- use refcount_t
-----BEGIN PGP SIGNATURE-----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=vZkA
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2021-08-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights:
- i915 has seen a lot of refactoring and uAPI cleanups due to a
change in the upstream direction going forward
This has all been audited with known userspace, but there may be
some pitfalls that were missed.
- i915 now uses common TTM to enable discrete memory on DG1/2 GPUs
- i915 enables Jasper and Elkhart Lake by default and has preliminary
XeHP/DG2 support
- amdgpu adds support for Cyan Skillfish
- lots of implicit fencing rules documented and fixed up in drivers
- msm now uses the core scheduler
- the irq midlayer has been removed for non-legacy drivers
- the sysfb code now works on more than x86.
Otherwise the usual smattering of stuff everywhere, panels, bridges,
refactorings.
Detailed summary:
core:
- extract i915 eDP backlight into core
- DP aux bus support
- drm_device.irq_enabled removed
- port drivers to native irq interfaces
- export gem shadow plane handling for vgem
- print proper driver name in framebuffer registration
- driver fixes for implicit fencing rules
- ARM fixed rate compression modifier added
- updated fb damage handling
- rmfb ioctl logging/docs
- drop drm_gem_object_put_locked
- define DRM_FORMAT_MAX_PLANES
- add gem fb vmap/vunmap helpers
- add lockdep_assert(once) helpers
- mark drm irq midlayer as legacy
- use offset adjusted bo mapping conversion
vgaarb:
- cleanups
fbdev:
- extend efifb handling to all arches
- div by 0 fixes for multiple drivers
udmabuf:
- add hugepage mapping support
dma-buf:
- non-dynamic exporter fixups
- document implicit fencing rules
amdgpu:
- Initial Cyan Skillfish support
- switch virtual DCE over to vkms based atomic
- VCN/JPEG power down fixes
- NAVI PCIE link handling fixes
- AMD HDMI freesync fixes
- Yellow Carp + Beige Goby fixes
- Clockgating/S0ix/SMU/EEPROM fixes
- embed hw fence in job
- rework dma-resv handling
- ensure eviction to system ram
amdkfd:
- uapi: SVM address range query added
- sysfs leak fix
- GPUVM TLB optimizations
- vmfault/migration counters
i915:
- Enable JSL and EHL by default
- preliminary XeHP/DG2 support
- remove all CNL support (never shipped)
- move to TTM for discrete memory support
- allow mixed object mmap handling
- GEM uAPI spring cleaning
- add I915_MMAP_OBJECT_FIXED
- reinstate ADL-P mmap ioctls
- drop a bunch of unused by userspace features
- disable and remove GPU relocations
- revert some i915 misfeatures
- major refactoring of GuC for Gen11+
- execbuffer object locking separate step
- reject caching/set-domain on discrete
- Enable pipe DMC loading on XE-LPD and ADL-P
- add PSF GV point support
- Refactor and fix DDI buffer translations
- Clean up FBC CFB allocation code
- Finish INTEL_GEN() and friends macro conversions
nouveau:
- add eDP backlight support
- implicit fence fix
msm:
- a680/7c3 support
- drm/scheduler conversion
panfrost:
- rework GPU reset
virtio:
- fix fencing for planes
ast:
- add detect support
bochs:
- move to tiny GPU driver
vc4:
- use hotplug irqs
- HDMI codec support
vmwgfx:
- use internal vmware device headers
ingenic:
- demidlayering irq
rcar-du:
- shutdown fixes
- convert to bridge connector helpers
zynqmp-dsub:
- misc fixes
mgag200:
- convert PLL handling to atomic
mediatek:
- MT8133 AAL support
- gem mmap object support
- MT8167 support
etnaviv:
- NXP Layerscape LS1028A SoC support
- GEM mmap cleanups
tegra:
- new user API
exynos:
- missing unlock fix
- build warning fix
- use refcount_t"
* tag 'drm-next-2021-08-31-1' of git://anongit.freedesktop.org/drm/drm: (1318 commits)
drm/amd/display: Move AllowDRAMSelfRefreshOrDRAMClockChangeInVblank to bounding box
drm/amd/display: Remove duplicate dml init
drm/amd/display: Update bounding box states (v2)
drm/amd/display: Update number of DCN3 clock states
drm/amdgpu: disable GFX CGCG in aldebaran
drm/amdgpu: Clear RAS interrupt status on aldebaran
drm/amdgpu: Add support for RAS XGMI err query
drm/amdkfd: Account for SH/SE count when setting up cu masks.
drm/amdgpu: rename amdgpu_bo_get_preferred_pin_domain
drm/amdgpu: drop redundant cancel_delayed_work_sync call
drm/amdgpu: add missing cleanups for more ASICs on UVD/VCE suspend
drm/amdgpu: add missing cleanups for Polaris12 UVD/VCE on suspend
drm/amdkfd: map SVM range with correct access permission
drm/amdkfd: check access permisson to restore retry fault
drm/amdgpu: Update RAS XGMI Error Query
drm/amdgpu: Add driver infrastructure for MCA RAS
drm/amd/display: Add Logging for HDMI color depth information
drm/amd/amdgpu: consolidate PSP TA init shared buf functions
drm/amd/amdgpu: add name field back to ras_common_if
drm/amdgpu: Fix build with missing pm_suspend_target_state module export
...
1. MT8133 AAL support, adjust rdma fifo threshold formula.
2. Implement mmap as GEM object function.
3. Add support for MT8167.
4. Test component initialization earlier in the function mtk_drm_crtc_create.
5. CMDQ refinement.
-----BEGIN PGP SIGNATURE-----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=OMls
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.15' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.15
1. MT8133 AAL support, adjust rdma fifo threshold formula.
2. Implement mmap as GEM object function.
3. Add support for MT8167.
4. Test component initialization earlier in the function mtk_drm_crtc_create.
5. CMDQ refinement.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210816232427.13368-1-chunkuang.hu@kernel.org
In cmdq mode, packet may be flushed before it is executed, so
the pending flag should be cleared after cmdq packet is done.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
One mtk_crtc need just one cmdq_handle, so add one cmdq_handle
in mtk_crtc to prevent frequently allocation and free of
cmdq_handle.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
CMDQ is used to update display register in vblank period, so
it should be execute in next vblank. If it fail to execute
in next 2 vblank, tiemout happen.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In mailbox rx_callback, it pass struct mbox_client to callback
function, but it could not map back to mtk_drm_crtc instance
because struct cmdq_client use a pointer to struct mbox_client:
struct cmdq_client {
struct mbox_client client;
struct mbox_chan *chan;
};
struct mtk_drm_crtc {
/* client instance data */
struct cmdq_client *cmdq_client;
};
so remove struct cmdq_client and let mtk_drm_crtc instance define
mbox_client as:
struct mtk_drm_crtc {
/* client instance data */
struct mbox_client cl;
};
and in rx_callback function, use struct mbox_client to get
struct mtk_drm_crtc.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
rx_callback is a standard mailbox callback mechanism and could cover the
function of proprietary cmdq_task_cb, so use the standard one instead of
the proprietary one.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add component_del in OVL and COLOR remove function.
Fixes: ff1395609e ("drm/mediatek: Move mtk_ddp_comp_init() from sub driver to DRM driver")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
To avoid the output width and height is incorrect,
AAL_OUTPUT_SIZE configuration should be set.
Fixes: 0664d1392c ("drm/mediatek: Add AAL engine basic function")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The initialization is currently tested in a later stage in
the function for no reason.
In addition, the test '!comp' will never fail since comp is
set with the '&' operator. Instead, test if a comp was not
initialized by testing "!comp->dev".
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add the main (DSI) drm display path for MT8167.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Moving the driver-specific mmap code into a GEM object function allows
for using DRM helpers for various mmap callbacks.
The respective mediatek functions are being removed. The file_operations
structure fops is now being created by the helper macro
DEFINE_DRM_GEM_FOPS().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
-----BEGIN PGP SIGNATURE-----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=ZSMl
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-07-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a753221a-e23e-0dc4-7ca6-8c1b179738d0@linux.intel.com
Being informed of a failure to attach a bridge is useful, and many
drivers prints an error message in that case. Move the message to
drm_bridge_attach() to avoid code duplication.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Many of the DSI flags have names opposite to their actual effects,
e.g. MIPI_DSI_MODE_EOT_PACKET means that EoT packets will actually
be disabled. Fix this by including _NO_ in the flag names, e.g.
MIPI_DSI_MODE_NO_EOT_PACKET.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@samsung.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com> # anx7625.c
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> # msm/dsi
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727094435.v3.1.I629b2366a6591410359c7fcf6d385b474b705ca2@changeid
MT8173 aal has gamma function but mt8183 aal has no gamma
function, so separate aal sub driver to have a private
data for different SoC.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The cursor plane should use the current plane state in atomic_async_update
because it would not be the new plane state in the global atomic state
since _swap_state happened when those hook are run.
Fix cursor plane issue by below modification:
1. Remove plane_helper_funcs->atomic_update(plane, state) in
mtk_drm_crtc_async_update.
2. Add mtk_drm_update_new_state in to mtk_plane_atomic_async_update to
update the cursor plane by current plane state hook and update
others plane by the new_state.
Fixes: 37418bf14c ("drm: Use state helper instead of the plane state pointer")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
atomic_get_output_bus_fmts() is only called when the bridge is the last
element in the bridge chain.
If mtk-dpi is not the last bridge, the format of output_bus_cfg is
MEDIA_BUS_FMT_FIXED, and mtk_dpi_dual_edge() will fail to write correct
value to regs.
Fixes: ec8747c524 ("drm/mediatek: dpi: Add bus format negotiation")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
bridge->driver_private is not set (NULL) so use bridge_to_dpi(bridge)
like it's done in bridge_atomic_get_output_bus_fmts
Fixes: ec8747c524 ("drm/mediatek: dpi: Add bus format negotiation")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
-----BEGIN PGP SIGNATURE-----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=x8Eo
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-07-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Fri 16 Jul 2021 21:06:04 AEST
# gpg: using RSA key B97BD6A80CAC4981091AE547FE558C72A67013C3
# gpg: Good signature from "Maarten Lankhorst <maarten.lankhorst@linux.intel.com>" [expired]
# gpg: aka "Maarten Lankhorst <maarten@debian.org>" [expired]
# gpg: aka "Maarten Lankhorst <maarten.lankhorst@canonical.com>" [expired]
# gpg: Note: This key has expired!
# Primary key fingerprint: B97B D6A8 0CAC 4981 091A E547 FE55 8C72 A670 13C3
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/444811c3-cbec-e9d5-9a6b-9632eda7962a@linux.intel.com
The orginal formula will caused rdma fifo threshold config overflow
and no one could come out a solution for all SoC,
set threshold to 70% of max fifo size to make sure it will
not overflow, and 70% is a empirical vlaue.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The field drm_device.irq_enabled is only used by legacy drivers
with userspace modesetting. Don't set it in mediatek.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625082222.3845-14-tzimmermann@suse.de
Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negotiate
the possible output and input formats for the current mode and monitor,
and use the negotiated formats in a basic atomic_check callback.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
For each SoC, dpi support different output bus formats, so
add these information into driver data.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
To support RGB888_2X12_LE and RGB888_2X12_BE, dpi should sample
on dual edge which could recude half data io pins.
For RGB888_1X24, dpi just sample on single edge (rising or falling
edge).
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:72: warning: Function parameter or member 'clk' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:72: warning: Function parameter or member 'regs' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:72: warning: Function parameter or member 'cmdq_reg' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:72: warning: Function parameter or member 'vblank_cb' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:72: warning: Function parameter or member 'vblank_cb_data' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:72: warning: Function parameter or member 'fifo_size' not described in 'mtk_disp_rdma'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210602143300.2330146-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:83: warning: Function parameter or member 'clk' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:83: warning: Function parameter or member 'regs' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:83: warning: Function parameter or member 'cmdq_reg' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:83: warning: Function parameter or member 'vblank_cb' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:83: warning: Function parameter or member 'vblank_cb_data' not described in 'mtk_disp_ovl'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210602143300.2330146-4-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_gamma.c:42: warning: Function parameter or member 'clk' not described in 'mtk_disp_gamma'
drivers/gpu/drm/mediatek/mtk_disp_gamma.c:42: warning: Function parameter or member 'regs' not described in 'mtk_disp_gamma'
drivers/gpu/drm/mediatek/mtk_disp_gamma.c:42: warning: Function parameter or member 'cmdq_reg' not described in 'mtk_disp_gamma'
drivers/gpu/drm/mediatek/mtk_disp_gamma.c:42: warning: Function parameter or member 'data' not described in 'mtk_disp_gamma'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210602143300.2330146-3-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_color.c:45: warning: Function parameter or member 'clk' not described in 'mtk_disp_color'
drivers/gpu/drm/mediatek/mtk_disp_color.c:45: warning: Function parameter or member 'regs' not described in 'mtk_disp_color'
drivers/gpu/drm/mediatek/mtk_disp_color.c:45: warning: Function parameter or member 'cmdq_reg' not described in 'mtk_disp_color'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210602143300.2330146-2-lee.jones@linaro.org
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The MT8167 SoC have a hard limit on the maximal supported
HDMI TMDS clock, and is not validated and supported for
HDMI modes out of HDMI CEA modes, so add a configuration entry
linked to the MT8167 compatible.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some SoCs like the MT8167 have a hard limit on the maximal
supported HDMI TMDS clock, so add a configuration value to
filter out those modes.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some SoCs like the MT8167 are not validated and supported for
HDMI modes out of HDMI CEA modes, so add a configuration boolean
to filter out non-CEA modes.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
1. Fine tune the line time for EOTp.
2. Add support mt8192 dpi.
3. Make crtc config-updating atomic.
4. Don't support hdmi connector creation.
-----BEGIN PGP SIGNATURE-----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=VClB
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.13' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.13
1. Fine tune the line time for EOTp.
2. Add support mt8192 dpi.
3. Make crtc config-updating atomic.
4. Don't support hdmi connector creation.
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210405082248.3578-1-chunkuang.hu@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit f011951489 ("drm/mediatek: mtk_dpi: Create connector for bridges")
broke the display support for elm device since mtk_dpi calls
drm_bridge_attach with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR
while mtk_hdmi does not yet support this flag.
Fix this by accepting DRM_BRIDGE_ATTACH_NO_CONNECTOR in bridge attachment.
Implement the drm_bridge_funcs .detect() and .get_edid() operations, and
call drm_bridge_hpd_notify() to report HPD. This provides the
necessary API to support disabling connector creation.
In addition, the field 'conn' is removed from the mtk_hdmi struct since
mtk_hdmi don't create a connector. It is replaced with a pointer
'curr_conn' that points to the current connector which can be access
through the global state.
This patch is inspired by a similar patch for bridge/synopsys/dw-hdmi.c:
commit ec971aaa67
("drm: bridge: dw-hdmi: Make connector creation optional")
But with the difference that in mtk-hdmi only the option of not creating
a connector is supported.
Fixes: f011951489 ("drm/mediatek: mtk_dpi: Create connector for bridges")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The bridge operation '.enable' and the audio cb '.get_eld'
access hdmi->conn. In the future we will want to support
the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR and then we will
not have direct access to the connector.
The atomic version '.atomic_enable' allows accessing the
current connector from the state.
This patch switches the bridge to the atomic version to
prepare access to the connector in later patches.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This patch adds the missing MODULE_DEVICE_TABLE definitions on different
Mediatek drivers which generates correct modalias for automatic loading
when these drivers are compiled as an external module.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
While updating config, the irq would occur and get the partial
config, so use variable config_updating to make updating atomic.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add dpi config setting and compatible for MT8192.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
platform_get_irq() has already checked and printed the return value,
the printing here is nothing special, it is not necessary at all.
Signed-off-by: tangchunyou <tangchunyou@yulong.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
platform_get_irq() has already checked and printed the return value,
the printing here is nothing special, it is not necessary at all.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Enabling EoTp will make the line time larger, so the hfp and
hbp should be reduced to keep line time.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
For HSTX_CKLP_EN and DIS_EOT, use symbolized register
definition instead of magic number.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Many drivers reference the plane->state pointer in order to get the
current plane state in their atomic_update or atomic_disable hooks,
which would be the new plane state in the global atomic state since
_swap_state happened when those hooks are run.
Use the drm_atomic_get_new_plane_state helper to get that state to make it
more obvious.
This was made using the coccinelle script below:
@ plane_atomic_func @
identifier helpers;
identifier func;
@@
(
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_disable = func,
...,
};
|
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_update = func,
...,
};
)
@ adds_new_state @
identifier plane_atomic_func.func;
identifier plane, state;
identifier new_state;
@@
func(struct drm_plane *plane, struct drm_atomic_state *state)
{
...
- struct drm_plane_state *new_state = plane->state;
+ struct drm_plane_state *new_state = drm_atomic_get_new_plane_state(state, plane);
...
}
@ include depends on adds_new_state @
@@
#include <drm/drm_atomic.h>
@ no_include depends on !include && adds_new_state @
@@
+ #include <drm/drm_atomic.h>
#include <drm/...>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20210219120032.260676-1-maxime@cerno.tech
The current atomic helpers have either their object state being passed as
an argument or the full atomic state.
The former is the pattern that was done at first, before switching to the
latter for new hooks or when it was needed.
Let's convert all the remaining helpers to provide a consistent
interface, starting with the planes atomic_check.
The conversion was done using the coccinelle script below plus some
manual changes for vmwgfx, built tested on all the drivers.
@@
identifier plane, plane_state;
symbol state;
@@
struct drm_plane_helper_funcs {
...
int (*atomic_check)(struct drm_plane *plane,
- struct drm_plane_state *plane_state);
+ struct drm_atomic_state *state);
...
}
@ plane_atomic_func @
identifier helpers;
identifier func;
@@
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_check = func,
...,
};
@@
struct drm_plane_helper_funcs *FUNCS;
identifier f;
identifier dev;
identifier plane, plane_state, state;
@@
f(struct drm_device *dev, struct drm_atomic_state *state)
{
<+...
- FUNCS->atomic_check(plane, plane_state)
+ FUNCS->atomic_check(plane, state)
...+>
}
@ ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
... when != new_plane_state
}
@ adds_new_state depends on plane_atomic_func && !ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
+ struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
...
}
@ depends on plane_atomic_func @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane,
- struct drm_plane_state *new_plane_state
+ struct drm_atomic_state *state
)
{ ... }
@ include depends on adds_new_state @
@@
#include <drm/drm_atomic.h>
@ no_include depends on !include && adds_new_state @
@@
+ #include <drm/drm_atomic.h>
#include <drm/...>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-4-maxime@cerno.tech
The function drm_gem_fb_prepare_fb() is a helper for atomic modesetting,
but currently located next to framebuffer helpers. Move it to GEM atomic
helpers, rename it slightly and adopt the drivers. Same for the rsp
simple-pipe helper.
Compile-tested with x86-64, aarch64 and arm. The patch is fairly large,
but there are no functional changes.
v3:
* remove out-comented line in drm_gem_framebuffer_helper.h
(Maxime)
v2:
* rename to drm_gem_plane_helper_prepare_fb() (Daniel)
* add tutorial-style documentation
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222141756.7864-1-tzimmermann@suse.de
1. Decouple Mediatek DRM sub driver
2. Share mtk mutex driver for both DRM and MDP
3. Add support for SoC MT8183
-----BEGIN PGP SIGNATURE-----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=s8K8
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.12' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.12
1. Decouple Mediatek DRM sub driver
2. Share mtk mutex driver for both DRM and MDP
3. Add support for SoC MT8183
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210204151750.7550-1-chunkuang.hu@kernel.org
Add matrix_bits and coeffs_precision to ccorr private data:
- matrix bits of mt8183 is 10
- matrix bits of mt8192 is 11
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fix setting to follow hardware datasheet. The original error setting
affects mt8192 display.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
ccorr ctm matrix bits will be different in mt8192.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Enable dither function to improve the display quality.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Enable OVL_LAYER_SMI_ID_EN for multi-layer usecase, without this patch,
ovl will hang up when more than 1 layer enabled.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
1. Add ovl private data
2. Add rdma private data
3. Add gamma privte data
4. Add main and external path module for crtc create
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Not all SoC has dither function in gamma module.
Add private data to control this function setting.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mt8183 gamma module will different with mt8173,
so separate gamma for adding private data.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Current implementation of mtk_dither_set() cast dev data to
struct mtk_ddp_comp_dev. But other devices with different dev data
would also call this function.
Separate necessary parameters out so other device components (dither,
gamma) can call this function.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mtk mutex is used by DRM and MDP driver, and its function is SoC-specific,
so move it to soc folder.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Moving mutex resource management from client driver to mutex driver
could prevent client drivers negotiating for resource management.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mtk mutex is used by both drm and mdp driver, so change disp/ddp term to
mutex to show that it's a common driver for drm and mdp.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
After mmsys routing function is moved out of mtk_drm_ddp.c, mtk_drm_ddp.c
has only mtk mutex function, so rename it to match the function in it.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Get the fifo size from device tree
because each rdma in the same SoC may have different fifo size
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The orginal setting is not correct, fix it to follow hardware data sheet.
If keep this error setting, mt8173/mt8183 display ok
but mt8192 display abnormal.
Fixes: 0664d1392c ("drm/mediatek: Add AAL engine basic function")
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Similar to commit a9d9fea74b
("drm/mediatek: mtk_dsi: Create connector for bridges"):
Use the drm_bridge_connector helper to create a connector for pipelines
that use drm_bridge. This allows splitting connector operations across
multiple bridges when necessary, instead of having the last bridge in
the chain creating the connector and handling all connector operations
internally.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
It's possible that state->base.fb is null. Add a check before access its
format.
Fixes: b6b1bb980e ("drm/mediatek: Turn off Alpha bit when plane format has no alpha")
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
-----BEGIN PGP SIGNATURE-----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=orEC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-12-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com
The interrupt trigger is already set by OF. When do devm_request_irq()
in driver, please use IRQF_TRIGGER_NONE and don't specify trigger type
again.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so
sub driver should not directly call DRM driver's function. Moving
mtk_ddp_comp_init() from sub driver to DRM driver to achieve this.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so
sub driver should not directly call DRM driver's function. Let
DRM driver directly refer to sub driver's function so that sub
driver need not register these function to DRM driver.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so
sub driver should not directly call crtc function. crtc register
callback function to sub driver to prevent sub driver directly
call crtc function.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so
sub driver interface should get rid of display info. Using device
instead of mtk_ddp_comp make interface general.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so data
belonged to sub driver should be moved into sub driver private data so it
could be used for multiple path. cmdq_reg info is one of sub driver data,
so move it.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
struct cmdq_client_reg include subsys and offset, so use it to replace
these two variable.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so data
belonged to sub driver should be moved into sub driver private data so it
could be used for multiple path. regs info is one of sub driver data, so
move it.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so data
belonged to sub driver should be moved into sub driver private data so it
could be used for multiple path. clk info is one of sub driver data, so
move it.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
To make the code cleaner, separate getting larb device to
a function.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component use mmsys device pointer to get CMDQ client
register, this would get mmsys' CMDQ client register, so use
each ddp component's device pointer to get.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Only OVL, RDMA,and WDMA get CMDQ client register information,
but all ddp component should work with CMDQ, so get this
information for all ddp component.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
To support legacy gamma ioctls the drivers need to set
drm_crtc_funcs.gamma_set either to a custom implementation or to
drm_atomic_helper_legacy_gamma_set. Most of the atomic drivers do the
latter.
We can simplify this by making the core handle it automatically.
Move the drm_atomic_helper_legacy_gamma_set() functionality into
drm_color_mgmt.c to make drm_mode_gamma_set_ioctl() use
drm_crtc_funcs.gamma_set if set or GAMMA_LUT property if not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201211114237.213288-2-tomi.valkeinen@ti.com
Required backmerge since we will be based on top of v5.11, and there
has been a request to backmerge already to upstream some features.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
1. Add MT8167 support
2. Cleanup function
3. Convert the dpi bindings to yaml
4. Drop local dma_parms
5. Fix formatting and provide missing member description
6. Introduce GEM object functions
7. Fix aliases name
8. Move MIPI DSI phy driver to phy folder
-----BEGIN PGP SIGNATURE-----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=iVNn
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.11-2
1. Add MT8167 support
2. Cleanup function
3. Convert the dpi bindings to yaml
4. Drop local dma_parms
5. Fix formatting and provide missing member description
6. Introduce GEM object functions
7. Fix aliases name
8. Move MIPI DSI phy driver to phy folder
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130234807.936-1-chunkuang.hu@kernel.org
mtk_mipi_dsi_phy is currently placed inside mediatek drm driver, but it's
more suitable to place a phy driver into phy driver folder, so move
mtk_mipi_dsi_phy driver into phy driver folder.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
mtk_mipi_tx is a part of mtk_drm module, but phy driver should be an
independent module rather than be part of drm module, so separate the phy
driver to an independent module.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Mapping the imported pages of a DMA-buf into an userspace process
doesn't work as expected.
But we have reoccurring requests on this approach, so split the
functions for this and document that dma_buf_mmap() needs to be used
instead.
v2: split it into two functions
v3: rebased on latest changes
v4: update commit message a bit
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/403838/
Aliases property name must include only lowercase and '-', so fix this
in the driver, so we're not tempted to do "ovl_2l0 = &ovl_2l0" in the
device-tree instead of the right one which is "ovl-2l0 = &ovl_2l0".
Fixes: b17bdd0d7a ("drm/mediatek: add component OVL_2L0")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
MMSYS is the driver which controls the routing of these DDP components,
so the definition of the mtk_ddp_comp_id enum should be placed in mtk-mmsys.h
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20201006193320.405529-2-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
For each client driver, its timeout handler need to dump hardware register
or its state machine information, and their way to detect timeout are
also different, so remove timeout handler in helper function and
let client driver implement its own timeout handler.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20201102000438.29225-1-chunkuang.hu@kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
GEM object functions deprecate several similar callback interfaces in
struct drm_driver. This patch replaces the per-driver callbacks with
per-instance callbacks in mediatek. The only exception is gem_prime_mmap,
which is non-trivial to convert.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:75: warning: Function parameter or member 'ddp_comp' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:75: warning: Function parameter or member 'crtc' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:75: warning: Function parameter or member 'data' not described in 'mtk_disp_ovl'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_color.c:40: warning: Function parameter or member 'ddp_comp' not described in 'mtk_disp_color'
drivers/gpu/drm/mediatek/mtk_disp_color.c:40: warning: Function parameter or member 'crtc' not described in 'mtk_disp_color'
drivers/gpu/drm/mediatek/mtk_disp_color.c:40: warning: Function parameter or member 'data' not described in 'mtk_disp_color'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:66: warning: Function parameter or member 'ddp_comp' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:66: warning: Function parameter or member 'crtc' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:66: warning: Function parameter or member 'data' not described in 'mtk_disp_rdma'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Also the DMA segment size is simply a size, not a bitmask.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In the patch to be fixed, horizontal_backporch_byte become too large
for some panel, so roll back that patch. For small hfp or hbp panel,
using vm->hfront_porch + vm->hback_porch to calculate
horizontal_backporch_byte would make it negtive, so
use horizontal_backporch_byte itself to make it positive.
Fixes: 35bf948f1e ("drm/mediatek: dsi: Fix scrolling of panel with small hfp or hbp")
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Bilal Wasim <bilal.wasim@imgtec.com>
This needs someone with in-depth knowledge of the driver to complete.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_drm_crtc.c:62: warning: Function parameter or member 'pending_needs_vblank' not described in 'mtk_drm_crtc'
drivers/gpu/drm/mediatek/mtk_drm_crtc.c:62: warning: Function parameter or member 'event' not described in 'mtk_drm_crtc'
drivers/gpu/drm/mediatek/mtk_drm_crtc.c:62: warning: Function parameter or member 'layer_nr' not described in 'mtk_drm_crtc'
drivers/gpu/drm/mediatek/mtk_drm_crtc.c:62: warning: Function parameter or member 'pending_async_planes' not described in 'mtk_drm_crtc'
drivers/gpu/drm/mediatek/mtk_drm_crtc.c:62: warning: Function parameter or member 'cmdq_client' not described in 'mtk_drm_crtc'
drivers/gpu/drm/mediatek/mtk_drm_crtc.c:62: warning: Function parameter or member 'cmdq_event' not described in 'mtk_drm_crtc'
drivers/gpu/drm/mediatek/mtk_drm_crtc.c:62: warning: Function parameter or member 'hw_lock' not described in 'mtk_drm_crtc'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-12-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:66: warning: Function parameter or member 'ddp_comp' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:66: warning: Function parameter or member 'crtc' not described in 'mtk_disp_rdma'
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:66: warning: Function parameter or member 'data' not described in 'mtk_disp_rdma'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-11-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:75: warning: Function parameter or member 'ddp_comp' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:75: warning: Function parameter or member 'crtc' not described in 'mtk_disp_ovl'
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:75: warning: Function parameter or member 'data' not described in 'mtk_disp_ovl'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-10-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/mediatek/mtk_disp_color.c:40: warning: Function parameter or member 'ddp_comp' not described in 'mtk_disp_color'
drivers/gpu/drm/mediatek/mtk_disp_color.c:40: warning: Function parameter or member 'crtc' not described in 'mtk_disp_color'
drivers/gpu/drm/mediatek/mtk_disp_color.c:40: warning: Function parameter or member 'data' not described in 'mtk_disp_color'
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-9-lee.jones@linaro.org
Function mtk_hdmi_aud_set_input always return 0, no need to
keep the return value. Functions mtk_hdmi_aud_enable_packet &
mtk_hdmi_aud_on_off_hw_ncts are the same, these two functions
just call next functions. Maybe it`s a bit better to just call
the inner function.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Only the following drivers aren't converted:
- amdgpu, because of the driver_feature mangling due to virt support.
Subsequent patch will address this.
- nouveau, because DRIVER_ATOMIC uapi is still not the default on the
platforms where it's supported (i.e. again driver_feature mangling)
- vc4, again because of driver_feature mangling
- qxl, because the ioctl table is somewhere else and moving that is
maybe a bit too much, hence the num_ioctls assignment prevents a
const driver structure.
- arcpgu, because that is stuck behind a pending tiny-fication series
from me.
- legacy drivers, because legacy requires non-const drm_driver.
Note that for armada I also went ahead and made the ioctl array const.
Only cc'ing the driver people who've not been converted (everyone else
is way too much).
v2: Fix one misplaced const static, should be static const (0day)
v3:
- Improve commit message (Sam)
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: kernel test robot <lkp@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201104100425.1922351-5-daniel.vetter@ffwll.ch
Commit f89c696e7f ("drm/mediatek: mtk_dpi: Convert to bridge driver")
introduced the following build warning with W=1
drivers/gpu/drm/mediatek/mtk_dpi.c:530:39: warning: unused variable 'mtk_dpi_encoder_funcs' [-Wunused-const-variable]
static const struct drm_encoder_funcs mtk_dpi_encoder_funcs = {
This struct is and the 'mtk_dpi_encoder_destroy()' are not needed
anymore, so remove them.
Fixes: f89c696e7f ("drm/mediatek: mtk_dpi: Convert to bridge driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
New driver:
Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config
-----BEGIN PGP SIGNATURE-----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=4H8J
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
1. Move Mediatek HDMI PHY driver from DRM folder to PHY folder
2. Convert mtk-dpi to drm_bridge API
3. Disable tmds on mt2701
-----BEGIN PGP SIGNATURE-----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=NyM2
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.10
1. Move Mediatek HDMI PHY driver from DRM folder to PHY folder
2. Convert mtk-dpi to drm_bridge API
3. Disable tmds on mt2701
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200914231227.30500-1-chunkuang.hu@kernel.org
No need to clear event again since event always clear before wait.
This fix depend on patch:
"soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api"
Fixes: 2f965be7f9 ("drm/mediatek: apply CMDQ control flow")
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Reviewed-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/1594136714-11650-10-git-send-email-dennis-yc.hsieh@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clear parameter to let client decide if
event should be clear to 0 after GCE receive it.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/1594136714-11650-9-git-send-email-dennis-yc.hsieh@mediatek.com
[mb: fix commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
GEM object functions deprecate several similar callback interfaces in
struct drm_driver. This patch replaces the per-driver callbacks with
per-instance callbacks in mediatek. The only exception is gem_prime_mmap,
which is non-trivial to convert.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923102159.24084-9-tzimmermann@suse.de
if of_find_device_by_node() succeed, mtk_drm_kms_init() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
Fixes: 8f83f26891 ("drm/mediatek: Add HDMI support")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
if of_find_device_by_node() succeed, mtk_drm_kms_init() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mtk_ddp_comp_init() is called in a loop in mtk_drm_probe(), if it
fail, previous successive init component is not proccessed.
Thus uninitialize valid component and put their device if component
init failed.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
if of_find_device_by_node() succeed, mtk_ddp_comp_init() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: d0afe37f52 ("drm/mediatek: support CMDQ interface in ddp component")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Even though cmdq client is created successfully, without the cmdq event,
cmdq could not work correctly, so use CPU when fail to get cmdq event.
Fixes: 60fa8c13ab ("drm/mediatek: Move gce event property to mutex device node")
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Remove mtk_drm_ddp.h which is included more than once
Fixes: 9aef5867c8 ("drm/mediatek: drop use of drmP.h")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Convert mtk_dpi to a bridge driver with built-in encoder support for
compatibility with existing component drivers.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This is really a cosmetic change just to make a bit more readable the
code after convert the driver to drm_bridge. The bridge variable name
will be used by the encoder drm_bridge, and the chained bridge will be
named next_bridge.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Use common helper for converting a sg_table object into struct
page pointer array.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Use common helper for checking the contiguity of the imported dma-buf and
do this check before allocating resources, so the error path is simpler.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mtk_hdmi_phy is currently placed inside mediatek drm driver, but it's
more suitable to place a phy driver into phy driver folder, so move
mtk_hdmi_phy driver into phy driver folder.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
mtk_hdmi_phy is a part of mtk_hdmi module, but phy driver should be an
independent module rather than be part of drm module, so separate the phy
driver to an independent module.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
tz_disabled is used to control mtk_hdmi output signal, but this variable
is stored in mtk_hdmi_phy and mtk_hdmi_phy does not use it. So move
tz_disabled to mtk_hdmi where it's used.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
For current mediatek dsi encoder, its possible crtc is fixed in crtc
0, and mediatek dpi encoder's possible crtc is fixed in crtc 1. In
some SoC the possible crtc is not fixed in this case, so search
pipeline information to find out the correct possible crtc.
Signed-off-by: Stu Hsieh <stu.hsieh@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
on BPi-R2/mt7623 main-path have to be routed to DPI0 (hdmi) instead of DSI0
using compatible "mt7623-mmsys" already defined in dts
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
horizontal_backporch_byte should be hbp * bpp - hbp extra bytes.
So remove the wrong subtraction 10.
Fixes: 7a5bc4e22e ("drm/mediatek: change the dsi phytiming calculate method")
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larget cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
-
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJfK1atAAoJEAx081l5xIa+vDkQAJvl/mjbEA7fDy8Ysa0cgPLI
8nI4Bo/MaxkyRfUcP8+f/n3QQrRME37C0xa/Mn6SG1oFAdlovPwDqmDr5kjhkrMI
geo8oJb2Q+AsrJr+ejpuF+iq0FxWi64bLbwJFJ2nBet+lHTMzoPceWeq3gG1Vvfl
h6PV4B/9TjrnbhcKLIQSEmJ0kZp9uMkDBF/iynVn4+AKAkG1rQNjigdTH48IFPoz
28KuqG0B4NWu648zYXhjsN0kD3Dxjv3YOH+FsoWQpQa9icCTySYbySsQ7l0/XvA3
4BPtP3rWMhU46FHTBkWF72WQR4F0B4wm5DJJKMeG4vb1mXakOqAKcAq7JAbka+wL
PBIiU+AcAKRSiwHmYDuDWtDoSpvYncuo0p3IvNP5hhih+7hqCnLIULDWS+V8AUzW
39usS/DXsVKk/HGYIYC89cRwsqWYD4c7edzOBdPQxW4LNYCD2gXezLJ5TeeR2lih
y9JIVnPiluWleOovs4W3BoZNRuLc1rHBO6COToXjlme/48Z+sRHBAoge6UZurqRN
jr+e60cS7n/DOeJQuNf4UHZnK48Pc24+3kVfMHlX+OKn8VuKPGr+USkeHV/NYL/B
USiKCAxkkZM0dxerSb1/Ra9kGnchf0QBpA6Fsem8kV61Z4GVc+K6xJWg7KXB6n/3
7ZyalUKLwlOCz9sYsCCe
=Yvtd
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"New xilinx displayport driver, AMD support for two new GPUs (more
header files), i915 initial support for RocketLake and some work on
their DG1 (discrete chip).
The core also grew some lockdep annotations to try and constrain what
drivers do with dma-fences, and added some documentation on why the
idea of indefinite fences doesn't work.
The long list is below.
I do have some fixes trees outstanding, but I'll follow up with those
later.
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larger cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages"
* tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm: (1747 commits)
drm/msm: use kthread_create_worker instead of kthread_run
drm/msm/mdp5: Add MDP5 configuration for SDM636/660
drm/msm/dsi: Add DSI configuration for SDM660
drm/msm/mdp5: Add MDP5 configuration for SDM630
drm/msm/dsi: Add phy configuration for SDM630/636/660
drm/msm/a6xx: add A640/A650 hwcg
drm/msm/a6xx: hwcg tables in gpulist
drm/msm/dpu: add SM8250 to hw catalog
drm/msm/dpu: add SM8150 to hw catalog
drm/msm/dpu: intf timing path for displayport
drm/msm/dpu: set missing flush bits for INTF_2 and INTF_3
drm/msm/dpu: don't use INTF_INPUT_CTRL feature on sdm845
drm/msm/dpu: move some sspp caps to dpu_caps
drm/msm/dpu: update UBWC config for sm8150 and sm8250
drm/msm/dpu: use right setup_blend_config for sm8150 and sm8250
drm/msm/a6xx: set ubwc config for A640 and A650
drm/msm/adreno: un-open-code some packets
drm/msm: sync generated headers
drm/msm/a6xx: add build_bw_table for A640/A650
drm/msm/a6xx: fix crashstate capture for A650
...
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
-----BEGIN PGP SIGNATURE-----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=C3jr
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.9' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.9
This include converting mtk_dsi to drm_bridge API.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716233102.566-1-chunkuang.hu@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge v5.8-rc6 into drm-next
I've got a silent conflict + two trees based on fixes to merge.
Fixes a silent merge with amdgpu
Signed-off-by: Dave Airlie <airlied@redhat.com>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
For hdmi-codec, we need to update struct hdmi_codec_ops,
and all its users in the same time.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87d055xxj2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the drm_bridge_connector helper to create a connector for pipelines
that use drm_bridge. This allows splitting connector operations across
multiple bridges when necessary, instead of having the last bridge in
the chain creating the connector and handling all connector operations
internally.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Replace the manual panel handling code by a drm_panel_bridge. This
simplifies the driver and allows all components in the display pipeline
to be treated as bridges, paving the way to generic connector handling.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The mtk_dsi driver uses an empty implementation for its encoder. Replace
the code with the generic simple encoder.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Convert mtk_dsi to a bridge driver with built-in encoder support for
compatibility with existing component drivers.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This is really a cosmetic change just to make a bit more readable the
code after convert the driver to drm_bridge. The bridge variable name
will be used by the encoder drm_bridge, and the chained bridge will be
named next_bridge.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Equivalent information can be nowadays obtained using function tracer
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
There are some `static const u8` variables that are not used, this
triggers a warning building with `make W=1`, it is safe to remove them,
so do it and make the compiler more happy.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The driver will be loaded by via a platform device. So we
will need to get the device_node from the parent device.
Depending on this we will set the driver data.
As all this is done later already, just delete the call to
of_device_get_match_data.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In function mtk_dsi_clk_hs_state, remove unnecessary conversion
to bool return, this change is to make the code a bit readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Disable the plane if it's not visible. Otherwise mtk_ovl_layer_config()
would proceed with invalid plane and we may see vblank timeout.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Equivalent information can be nowadays obtained using function tracer.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----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=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
Export finalize function to client which helps append eoc and jump
command to pkt. Let client decide call finalize or not.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/1592749115-24158-9-git-send-email-dennis-yc.hsieh@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
-----BEGIN PGP SIGNATURE-----
iQJMBAABCgA2FiEEACwLKSDmq+9RDv5P4cpzo8lZTiQFAl7FwFkYHGNodW5rdWFu
Zy5odUBrZXJuZWwub3JnAAoJEOHKc6PJWU4khCkP/1ZKyyJd83FLQZ142j5KD64j
XeiJ7xxVNIjMcgJMLImOevF3XbNuON58D0xwcU+06yrUntt7qbWztug0OrmZvRiI
H4qxMXf5Yp/5EFGCVXrKw+UP9LPcYas2z2aD7WWI9p1NI6SQIBsazWu01daMd87U
GbxTg5xpOT0rFt6fpTpRyWEeQD2AALDRWTovxG1VfmYB5ZnioBk29vReSPQA93Un
HZhBQPTvj3NBgFtqhZQlS+4nr8CnAcJs++fcAKHnSJyQ3klmLcYIux8fKSRCd81W
F7dzshL1S1tPgFnU/CegiysfdEZX1FEaYSuzk6ALKAV6s/Xz+qz9FdUVZYxcE/2s
eG1fCXu6OVg1JYoFRO4ZcyfuMDHNwZzhyRb58atCN5s2gJwY+nID5nRiyFrPTA47
J+1cJubk/n3mWyezZp2oqo6u2a74C80RPMgjpAAG3VPoQGvEvUuNZXn4u5idpixT
LDYyMfdgJNL+cP78+y2WXFfAqUtg8A7IfnisT5teSr5t+HQ74H57mBb5muYehKhu
6gzyBkj5Nen1NIpwF+v0EX73PtzpUWmzk6AT6/8lrfq6Sjf3WTBzGeiI4e0vrUs9
aqIYRImMKGPZ5rTAvKx9fh2oZzH9B6x/zTUOMCZPkkXuHKg3PncXZywDVdq1Nwgz
vrsKuCrpNsyHPDQ6G+D6
=qbjB
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.8' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.8
This include dpi pin mode swap, config mipi_tx current and impedance,
and some fixup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200521014612.17175-1-chunkuang.hu@kernel.org
Eiminate the magic number in array size, there macro defines in
hdmi.h.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This code change is to make code bit more readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
If dma_map_sg() merges pages when creating the mapping, only the first
entries will have a valid sg_dma_address() and sg_dma_len(), followed by
entries with sg_dma_len() == 0.
Signed-off-by: Anand K Mistry <amistry@google.com>
Signed-off-by: Anand K Mistry <amistry@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
