Add the missing video resets that are needed for the iris video codec.
Copied from gcc-sm8550.c.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250709-x1e-videocc-v2-5-ad1acf5674b4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Update the force mem core bit for UFS ICE clock and UFS PHY AXI clock to
force the core on signal to remain active during halt state of the clk.
If force mem core bit of the clock is not set, the memories of the
subsystem will not retain the logic across power states. This is
required for the MCQ feature of UFS.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Imran Shaik <quic_imrashai@quicinc.com>
Link: https://lore.kernel.org/r/20250414-gcc_ufs_mem_core-v1-2-67b5529b9b5d@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The GPU clock is required for CPU access to GPUSS registers. It was
previously decided (on this and many more platforms) that the added
overhead/hassle introduced by keeping track of it would not bring much
measurable improvement in the power department.
The display clock is basically the same story over again.
Now, we're past that discussion and this commit is not trying to change
that. Instead, the clocks are both force-enabled in .probe *and*
registered with the common clock framework, resulting in them being
toggled off after ignore_unused.
Unregister said clocks to fix breakage when clk_ignore_unused is absent
(as it should be).
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250111-topic-x1e_fixups-v1-1-77dc39237c12@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Allowing the usb_2 controller GDSC to be turned off during system suspend
renders the controller unable to resume.
So use PWRSTS_RET_ON instead in order to make sure this the GDSC doesn't
go down.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250107-x1e80100-clk-gcc-fix-usb2-gdsc-pwrsts-v1-1-e15d1a5e7d80@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Allowing these GDSCs to collapse makes the QMP combo PHYs lose their
configuration on machine suspend. Currently, the QMP combo PHY driver
doesn't reinitialise the HW on resume. Under such conditions, the USB
SuperSpeed support is broken. To avoid this, mark the pwrsts flags with
RET_ON. This has been already done for USB 0 and 1 SS PHY GDSCs,
Do this also for the USB MP SS1 PHY GDSC config. The USB MP SS0 PHY GDSC
already has it.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241021-x1e80100-clk-gcc-fix-usb-mp-phy-gdsc-pwrsts-flags-v2-1-0bfd64556238@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The pipediv2_clk's source from the same mux as pipe clock. So they have
same limitation, which is that the PHY sequence requires to enable these
local CBCs before the PHY is actually outputting a clock to them. This
means the clock won't actually turn on when we vote them. Hence, let's
skip the halt bit check of the pipediv2_clk, otherwise pipediv2_clk may
stuck at off state during bootup.
Cc: stable@vger.kernel.org
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Suggested-by: Mike Tipton <quic_mdtipton@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241011104142.1181773-6-quic_qianyu@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Per Stephen Boyd's explanation in the link below, QUP RCG clocks do not
need to be parked when switching frequency. A side-effect in parking to a
lower frequency can be a momentary invalid clock driven on an in-use serial
peripheral.
This can cause "junk" to spewed out of a UART as a low-impact example. On
the x1e80100-crd this serial port junk can be observed on linux-next.
Apply a similar fix to the x1e80100 Global Clock controller to remediate.
Link: https://lore.kernel.org/all/20240819233628.2074654-3-swboyd@chromium.org/
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Fixes: 929c75d575 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240823-x1e80100-clk-fix-v1-1-0b1b4f5a96e8@linaro.org
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Allowing these GDSCs to collapse makes the QMP combo PHYs lose their
configuration on machine suspend. Currently, the QMP combo PHY driver
doesn't reinitialise the HW on resume. Under such conditions, the USB
SuperSpeed support is broken. To avoid this, mark the pwrsts flags with
RET_ON. This is in line with USB 2 PHY GDSC config.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240801-x1e80100-clk-gcc-fix-usb-phy-gdscs-pwrsts-v1-1-8df016768a0f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Allow the USB3 second and third GCC PHY pipe clocks to propagate the
rate to the pipe clocks provided by the QMP combo PHYs. The first
instance is already doing that.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240530-x1e80100-clk-gcc-usb3-sec-tert-set-parent-rate-v1-1-7b2b04cad545@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In case of all pipe clocks, there is a QMP PHY clock that is feeding them.
If, for whatever reason, the clock from the PHY is not enabled, halt bit
will not get set, and the clock controller driver will assume the clock
is stuck in a specific state. The way this is supposed to be properly
fixed is to defer the checking of the halt bit until after the PHY clock
has been initialized, but doing so complicates the clock controller
driver. In fact, since these pipe clocks are consumed by the PHY, while
the PHY is also the one providing the source, if clock gets stuck, the PHY
driver would be to blame. So instead of checking the halt bit in here,
just skip it and assume the PHY driver is handling the source clock
correctly.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20240628-x1e80100-clk-gcc-fix-halt-check-for-usb-phy-pipe-clks-v2-1-db3be54b1143@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The previous wrapper qcom_cc_really_probe takes the platform
device as parameter, which is limited to platform driver.
As for qca8k clock controller driver, which is registered as
the MDIO device, which also follows the qcom clock framework.
To commonize qcom_cc_really_probe, updating it to take the
struct device as parameter, so that the qcom_cc_really_probe
can be utilized by the previous platform device and the new
added MDIO device.
Also update the current clock controller drivers to take
&pdev->dev as parameter when calling qcom_cc_really_probe.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://lore.kernel.org/r/20240605124541.2711467-4-quic_luoj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Instead of magically poking at the bit0 of branch clocks' CBCR, use
the newly introduced helper.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240212-topic-clk_branch_en-v7-2-5b79eb7278b2@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h.
of_device.h isn't needed, but mod_devicetable.h and platform_device.h
were implicitly included.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20231211160510.0aef871b@canb.auug.org.au
[robh: Redo commit msg]
Signed-off-by: Rob Herring <robh@kernel.org>
Add support for the global clock controller found on X1E80100
based devices.
Co-developed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20231205061002.30759-3-quic_sibis@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
