Commit 0d297df038 ("ARM: s3c: simplify platform code") removes the line
in Makefile.s3c64xx to configure the inclusion of setup-ide-s3c64xx.c,
with CONFIG_S3C64XX_SETUP_IDE. So, since then, config S3C64XX_SETUP_IDE has
no effect and any further purpose.
Remove the obsolete config S3C64XX_SETUP_IDE.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230508040433.13648-1-lukas.bulwahn@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Following down the now unused symbols and header files, some additional
content can be dropped that is used by neither the s3c64xx DT support
nor the crag6410 board.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This driver could not be enabled on s3c64xx for a long time
because of the ARCH_MULTIPLATFORM dependency, so remove it.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All traditional board files except for MACH_WLF_CRAGG_6410 were
marked as unused, so remove them now.
Cc: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Maurus Cuelenaere <mcuelenaere@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Over the past ten years, new machine support was based on device tree,
and an initial set of about 400 boards using ATAGS with boardfile
for booting were grandfathered in, with about half of them either
removed or converted to DT over time.
Based on the recent mailing list discussion I started, I have now
turned the findings into a set of patches that marks most board files as
'depends on UNUSED_BOARD_FILES', leaving only 38 of the 196 boards.
For the boards that are marked as unused, there are two final chances
for potential users: The removal is scheduled to take place after the
longterm stable kernel at the end of 2022, so users can stay on that
version for another few years, and if anyone still has one of these
machines and is planning to keep updating kernels beyond that version,
they can speak up now to have their boards taken off the list again.
Waiting for the LTS release also makes sure that there will be at
least one longterm kernel that contains the recent multiplatform
conversion along while still supporting all legacy boards.
The short summary of the current status is:
- The s3c24xx, cns3xxx, iop32x and mv78xx0 platforms have no known
users and will be removed entirely.
- The mmp and davinci platforms have DT support for the important
machines and will become DT-only after this.
- s3c64xx, dove, orion5x, and pxa keep some board files to allow
those to be migrated over to DT more easily, but most board files
are getting removed now. DT support on these platforms is partially
working but requires changes to additional drivers for the other
boards.
- omap1, ep93xx, sa1100, footbridge and rpc have no DT support at
the moment but have some boards with known users. Removing the board
files that nobody uses should make it easier to try a DT conversion
if anyone cares.
There is no explicit timeline what happens with the boards that remain
after this removal, but I expect to revisit this in the future, and
with most boards gone, there will be a good time to do a treewide
review of platform drivers that never gained DT support and have no
remaining in-tree board files.
Link: https://lore.kernel.org/linux-arm-kernel/CAK8P3a0Z9vGEQbVRBo84bSyPFM-LF+hs5w8ZA51g2Z+NsdtDQA@mail.gmail.com/
-----BEGIN PGP SIGNATURE-----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=wd/l
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfiles-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM boardfile deprecation from Arnd Bergmann:
"Over the past ten years, new machine support was based on device tree,
and an initial set of about 400 boards using ATAGS with boardfile for
booting were grandfathered in, with about half of them either removed
or converted to DT over time.
Based on the recent mailing list discussion I started, I have now
turned the findings into a set of patches that marks most board files
as 'depends on UNUSED_BOARD_FILES', leaving only 38 of the 196 boards.
For the boards that are marked as unused, there are two final chances
for potential users: The removal is scheduled to take place after the
longterm stable kernel at the end of 2022, so users can stay on that
version for another few years, and if anyone still has one of these
machines and is planning to keep updating kernels beyond that version,
they can speak up now to have their boards taken off the list again.
Waiting for the LTS release also makes sure that there will be at
least one longterm kernel that contains the recent multiplatform
conversion along while still supporting all legacy boards.
The short summary of the current status is:
- The s3c24xx, cns3xxx, iop32x and mv78xx0 platforms have no known
users and will be removed entirely.
- The mmp and davinci platforms have DT support for the important
machines and will become DT-only after this.
- s3c64xx, dove, orion5x, and pxa keep some board files to allow
those to be migrated over to DT more easily, but most board files
are getting removed now. DT support on these platforms is partially
working but requires changes to additional drivers for the other
boards.
- omap1, ep93xx, sa1100, footbridge and rpc have no DT support at the
moment but have some boards with known users. Removing the board
files that nobody uses should make it easier to try a DT conversion
if anyone cares.
There is no explicit timeline what happens with the boards that remain
after this removal, but I expect to revisit this in the future, and
with most boards gone, there will be a good time to do a treewide
review of platform drivers that never gained DT support and have no
remaining in-tree board files"
Link: https://lore.kernel.org/linux-arm-kernel/CAK8P3a0Z9vGEQbVRBo84bSyPFM-LF+hs5w8ZA51g2Z+NsdtDQA@mail.gmail.com/
* tag 'arm-boardfiles-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: cns3xxx: add CONFIG_UNUSED_BOARD_FILES dependency
ARM: iop32x: mark as unused
ARM: s3c: mark most board files as unused
ARM: omap1: add Kconfig dependencies for unused boards
ARM: sa1100: mark most boards as unused
ARM: footbridge: mark cats board for removal
ARM: mmp: mark all board files for removal
ARM: ep93xx: mark most board files as unused
ARM: davinci: mark all ATAGS board files as unused
ARM: orion: add ATAGS dependencies
ARM: pxa: add Kconfig dependencies for ATAGS based boards
ARM: add CONFIG_UNUSED_BOARD_FILES
ARM: add ATAGS dependencies to non-DT platforms
The s3c24xx platform is already scheduled for removal in early 2023,
with s3c64xx meeting the same fate a year later.
Most of the s3c64xx board files appear to be unused, as the better
maintained ones already got converted to DT. The main exception is
the Wolfson Cragganmore board, which remains in use as the reference
design for Wolfson/Cirrus devices. As the other boards get removed,
this one stays around along with the DT based machines.
The s3c6400_defconfig file now disables the unused boards, while the
s3c24xx defconfig files all turn on CONFIG_UNUSED_BOARD_FILES to
remain usable.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The convention for indentation seems to be a single tab. Help text is
further indented by an additional two whitespaces. Fix the lines that
violate these rules.
Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Link: https://lore.kernel.org/r/20220609082154.115301-4-juerg.haefliger@canonical.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The Samsung S3C24xx and S3C64xx platforms are very old designs. S3C2416
was introduced in 2008 and S3C6410 in 2009/2010. They are not widely
available anymore - out-of-stock on FriendlyArm (one of manufacturers of
boards) and only few specialist stores still offer them for quite a high
price.
The community around these platforms was not very active, so I suspect
no one really uses them anymore. Maintenance takes precious time so
there is little sense in keeping them alive if there are no real users.
Let's mark all S3C24xx and S3C64xx platforms as deprecated and mention
possible removal in after 2022 for the first and 2024 for the lattere.
The deprecation message will be as text in Kconfig, build message (not a
warning though) and runtime print error.
If there are any users, they might respond and postpone the removal.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220407072319.75614-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A separate Kconfig option HAVE_S3C2410_I2C for Samsung SoCs is not
really needed and the i2c-s3c24xx driver can depend on Samsung ARM
architectures instead. This also enables i2c-s3c2410 for arm64 Exynos
SoCs, which is required for example by Exynos850.
This is basically continuation of work made in following commits:
- commit d96890fca9 ("rtc: s3c: remove HAVE_S3C_RTC in favor of
direct dependencies")
- commit 7dd3cae90d ("ARM: samsung: remove HAVE_S3C2410_WATCHDOG and
use direct dependencies")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211121150558.21801-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
s3c24xx and s3c64xx have a lot in common, but are split across three
separate directories, which makes the interaction of the header files
more complicated than necessary.
Move all three directories into a new mach-s3c, with a minimal
set of changes to each file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[krzk: Rebase, add s3c24xx and s3c64xx suffix to several files, add SPDX
headers to new files, remove plat-samsung from MAINTAINERS]
Co-developed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
https://lore.kernel.org/r/20200806182059.2431-39-krzk@kernel.org
