Proxmox-Port/linux-loongson
1
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson synced 2025-09-01 06:39:05 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
loongarch-next
linux-loongson/arch/arm64/boot/dts/rockchip/rk3588-h96-max-v58.dts
Sebastian Reichel f94500eb73 arm64: dts: rockchip: Add GPU power domain regulator dependency for RK3588 
Enabling the GPU power domain requires that the GPU regulator is
enabled. The regulator is enabled at boot time, but gets disabled
automatically when there are no users.

This means the system might run into a failure state hanging the
whole system for the following use cases:

 * if the GPU driver is being probed late (e.g. build as a
   module and firmware is not in initramfs), the regulator
   might already have been disabled. In that case the power
   domain is enabled before the regulator.
 * unbinding the GPU driver will disable the PM domain and
   the regulator. When the driver is bound again, the PM
   domain will be enabled before the regulator and error
   appears.

Avoid this by adding an explicit regulator dependency to the
power domain.

Tested-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: Adrián Martínez Larumbe <adrian.larumbe@collabora.com>
Tested-by: Adrian Larumbe <adrian.larumbe@collabora.com> # On Rock 5B
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250220-rk3588-gpu-pwr-domain-regulator-v6-8-a4f9c24e5b81@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-02-28 14:44:49 +01:00

831 lines
17 KiB
Plaintext
Raw Permalink Blame History

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/soc/rockchip,vop2.h>
#include "rk3588.dtsi"
/ {
model = "H96 Max V58 TV Box";
compatible = "haochuangyi,h96-max-v58", "rockchip,rk3588";
aliases {
ethernet0 = &gmac1;
mmc0 = &sdhci;
};
adc-keys {
compatible = "adc-keys";
io-channels = <&saradc 1>;
io-channel-names = "buttons";
keyup-threshold-microvolt = <1800000>;
poll-interval = <100>;
button-function {
label = "Reset";
linux,code = <KEY_VENDOR>;
press-threshold-microvolt = <1750>;
};
};
chosen {
stdout-path = "serial2:1500000n8";
};
hdmi0-con {
compatible = "hdmi-connector";
type = "a";
port {
hdmi0_con_in: endpoint {
remote-endpoint = <&hdmi0_out_con>;
};
};
};
ir-receiver {
compatible = "gpio-ir-receiver";
gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&ir_receiver_pin>;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
led {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_STATUS;
gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
vcc_1v1_nldo_s3: regulator-1v1 {
compatible = "regulator-fixed";
regulator-name = "vcc_1v1_nldo_s3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
vin-supply = <&vcc5v0_sys>;
};
pcie_3v3: regulator-3v3-pcie {
compatible = "regulator-fixed";
enable-active-high;
gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&pcie2_0_pow>;
pinctrl-names = "default";
regulator-name = "pcie_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc5v0_sys>;
};
wl_en_3v3: regulator-3v3-wlen {
compatible = "regulator-fixed";
enable-active-high;
gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&wl_en>;
pinctrl-names = "default";
/*
* Needs to be brought up before the PCIe driver is probed,
* otherwise detecting the WLAN module requires rescanning
* the bus, and even then it fails half of the time during
* firmware load
*/
regulator-always-on;
regulator-boot-on;
regulator-name = "wl_en_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc5v0_sys>;
};
vcc5v0_host: regulator-5v0-host {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_host";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&vcc5v0_host_en>;
pinctrl-names = "default";
vin-supply = <&vcc5v0_sys>;
};
vcc5v0_otg: regulator-5v0-otg {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_otg";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
pinctrl-0 = <&vcc5v0_otg_en>;
pinctrl-names = "default";
vin-supply = <&vcc5v0_sys>;
};
vcc5v0_sys: regulator-5v0-sys {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_sys";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
spdif_dit: spdif-dit {
compatible = "linux,spdif-dit";
#sound-dai-cells = <0>;
};
spdif_sound: spdif-sound {
compatible = "simple-audio-card";
simple-audio-card,name = "SPDIF";
simple-audio-card,cpu {
sound-dai = <&spdif_tx0>;
};
simple-audio-card,codec {
sound-dai = <&spdif_dit>;
};
};
};
&combphy0_ps {
status = "okay";
};
&combphy1_ps {
status = "okay";
};
&combphy2_psu {
status = "okay";
};
&cpu_b0 {
cpu-supply = <&vdd_cpu_big0_s0>;
};
&cpu_b1 {
cpu-supply = <&vdd_cpu_big0_s0>;
};
&cpu_b2 {
cpu-supply = <&vdd_cpu_big1_s0>;
};
&cpu_b3 {
cpu-supply = <&vdd_cpu_big1_s0>;
};
&cpu_l0 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
&cpu_l1 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
&cpu_l2 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
&cpu_l3 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
&gpu {
mali-supply = <&vdd_gpu_s0>;
status = "okay";
};
&hdmi0 {
status = "okay";
};
&hdmi0_in {
hdmi0_in_vp0: endpoint {
remote-endpoint = <&vp0_out_hdmi0>;
};
};
&hdmi0_out {
hdmi0_out_con: endpoint {
remote-endpoint = <&hdmi0_con_in>;
};
};
&hdptxphy0 {
status = "okay";
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0m2_xfer>;
status = "okay";
vdd_cpu_big0_s0: regulator@42 {
compatible = "rockchip,rk8602";
reg = <0x42>;
fcs,suspend-voltage-selector = <1>;
regulator-name = "vdd_cpu_big0_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <1050000>;
regulator-ramp-delay = <2300>;
vin-supply = <&vcc5v0_sys>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_cpu_big1_s0: regulator@43 {
compatible = "rockchip,rk8603", "rockchip,rk8602";
reg = <0x43>;
fcs,suspend-voltage-selector = <1>;
regulator-name = "vdd_cpu_big1_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <1050000>;
regulator-ramp-delay = <2300>;
vin-supply = <&vcc5v0_sys>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
};
&i2c6 {
status = "okay";
hym8563: rtc@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-output-names = "hym8563";
pinctrl-names = "default";
pinctrl-0 = <&hym8563_int>;
interrupt-parent = <&gpio0>;
interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
wakeup-source;
};
};
&gmac1 {
clock_in_out = "output";
phy-handle = <&rgmii_phy1>;
phy-mode = "rgmii-id";
pinctrl-0 = <&gmac1_miim
&gmac1_tx_bus2
&gmac1_rx_bus2
&gmac1_rgmii_clk
&gmac1_rgmii_bus>;
pinctrl-names = "default";
status = "okay";
};
&mdio1 {
rgmii_phy1: ethernet-phy@1 {
/* RTL8211F */
compatible = "ethernet-phy-id001c.c916";
reg = <0x1>;
pinctrl-names = "default";
pinctrl-0 = <&rtl8211f_rst>;
reset-assert-us = <20000>;
reset-deassert-us = <100000>;
reset-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
};
};
&pcie2x1l0 {
pinctrl-names = "default";
pinctrl-0 = <&pcie2_0_rst>;
reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
status = "okay";
pcie@0,0 {
reg = <0x200000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
device_type = "pci";
bus-range = <0x20 0x2f>;
wifi: wifi@0,0 {
compatible = "pci14e4,449d";
reg = <0x210000 0 0 0 0>;
clocks = <&hym8563>;
clock-names = "lpo";
};
};
};
&pd_gpu {
domain-supply = <&vdd_gpu_s0>;
};
&pinctrl {
hym8563 {
hym8563_int: hym8563-int {
rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
ir-receiver {
ir_receiver_pin: ir-receiver-pin {
rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
leds {
led_pins: led-pins {
rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
pcie2 {
pcie2_0_rst: pcie2-0-rst {
rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
};
pcie2_0_pow: pcie2-0-pow {
rockchip,pins = <4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
rtl8211f {
rtl8211f_rst: rtl8211f-rst {
rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
usb {
vcc5v0_host_en: vcc5v0-host-en {
rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
};
vcc5v0_otg_en: vcc5v0-otg-en {
rockchip,pins = <4 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
wifibt {
wl_en: wl-en {
rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>;
};
wl_wake_host: wl-wake-host {
rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
};
bt_en: bt-en {
rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
};
bt_wake: bt-wake {
rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
};
bt_wake_host: bt-wake-host {
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
};
&saradc {
vref-supply = <&avcc_1v8_s0>;
status = "okay";
};
&sdhci {
bus-width = <8>;
no-sdio;
no-sd;
non-removable;
mmc-hs400-1_8v;
mmc-hs400-enhanced-strobe;
status = "okay";
};
&spdif_tx0 {
pinctrl-names = "default";
pinctrl-0 = <&spdif0m1_tx>;
status = "okay";
};
&spi2 {
assigned-clocks = <&cru CLK_SPI2>;
assigned-clock-rates = <200000000>;
num-cs = <1>;
pinctrl-names = "default";
pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
status = "okay";
pmic@0 {
compatible = "rockchip,rk806";
reg = <0x0>;
interrupt-parent = <&gpio0>;
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
<&rk806_dvs2_null>, <&rk806_dvs3_null>;
spi-max-frequency = <1000000>;
system-power-controller;
vcc1-supply = <&vcc5v0_sys>;
vcc2-supply = <&vcc5v0_sys>;
vcc3-supply = <&vcc5v0_sys>;
vcc4-supply = <&vcc5v0_sys>;
vcc5-supply = <&vcc5v0_sys>;
vcc6-supply = <&vcc5v0_sys>;
vcc7-supply = <&vcc5v0_sys>;
vcc8-supply = <&vcc5v0_sys>;
vcc9-supply = <&vcc5v0_sys>;
vcc10-supply = <&vcc5v0_sys>;
vcc11-supply = <&vcc_2v0_pldo_s3>;
vcc12-supply = <&vcc5v0_sys>;
vcc13-supply = <&vcc_1v1_nldo_s3>;
vcc14-supply = <&vcc_1v1_nldo_s3>;
vcca-supply = <&vcc5v0_sys>;
gpio-controller;
#gpio-cells = <2>;
rk806_dvs1_null: dvs1-null-pins {
pins = "gpio_pwrctrl1";
function = "pin_fun0";
};
rk806_dvs2_null: dvs2-null-pins {
pins = "gpio_pwrctrl2";
function = "pin_fun0";
};
rk806_dvs3_null: dvs3-null-pins {
pins = "gpio_pwrctrl3";
function = "pin_fun0";
};
regulators {
vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
regulator-name = "vdd_gpu_s0";
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <950000>;
regulator-ramp-delay = <12500>;
regulator-enable-ramp-delay = <400>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
regulator-name = "vdd_cpu_lit_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <950000>;
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_log_s0: dcdc-reg3 {
regulator-name = "vdd_log_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <675000>;
regulator-max-microvolt = <750000>;
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
regulator-suspend-microvolt = <750000>;
};
};
vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
regulator-name = "vdd_vdenc_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <550000>;
regulator-max-microvolt = <950000>;
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_ddr_s0: dcdc-reg5 {
regulator-name = "vdd_ddr_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <675000>;
regulator-max-microvolt = <900000>;
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
regulator-suspend-microvolt = <850000>;
};
};
vdd2_ddr_s3: dcdc-reg6 {
regulator-name = "vdd2_ddr_s3";
regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
};
};
vcc_2v0_pldo_s3: dcdc-reg7 {
regulator-name = "vdd_2v0_pldo_s3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <2000000>;
};
};
vcc_3v3_s3: dcdc-reg8 {
regulator-name = "vcc_3v3_s3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <3300000>;
};
};
vddq_ddr_s0: dcdc-reg9 {
regulator-name = "vddq_ddr_s0";
regulator-always-on;
regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_1v8_s3: dcdc-reg10 {
regulator-name = "vcc_1v8_s3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
};
avcc_1v8_s0: pldo-reg1 {
regulator-name = "avcc_1v8_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_1v8_s0: pldo-reg2 {
regulator-name = "vcc_1v8_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-state-mem {
regulator-off-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
};
avdd_1v2_s0: pldo-reg3 {
regulator-name = "avdd_1v2_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_3v3_s0: pldo-reg4 {
regulator-name = "vcc_3v3_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vccio_sd_s0: pldo-reg5 {
regulator-name = "vccio_sd_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-ramp-delay = <12500>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
pldo6_s3: pldo-reg6 {
regulator-name = "pldo6_s3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
};
vdd_0v75_s3: nldo-reg1 {
regulator-name = "vdd_0v75_s3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <750000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <750000>;
};
};
vdd_ddr_pll_s0: nldo-reg2 {
regulator-name = "vdd_ddr_pll_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <850000>;
regulator-state-mem {
regulator-off-in-suspend;
regulator-suspend-microvolt = <850000>;
};
};
avdd_0v75_s0: nldo-reg3 {
regulator-name = "avdd_0v75_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <750000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_0v85_s0: nldo-reg4 {
regulator-name = "vdd_0v85_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <850000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_0v75_s0: nldo-reg5 {
regulator-name = "vdd_0v75_s0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <750000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
};
};
};
&tsadc {
status = "okay";
};
&u2phy0 {
status = "okay";
};
&u2phy0_otg {
phy-supply = <&vcc5v0_otg>;
status = "okay";
};
&u2phy1 {
status = "okay";
};
&u2phy1_otg {
phy-supply = <&vcc5v0_host>;
status = "okay";
};
&uart2 {
pinctrl-0 = <&uart2m0_xfer>;
status = "okay";
};
&uart9 {
pinctrl-0 = <&uart9m0_xfer &uart9m0_ctsn &uart9m0_rtsn>;
pinctrl-names = "default";
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "brcm,bcm43438-bt";
clocks = <&hym8563>;
clock-names = "lpo";
device-wakeup-gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
interrupt-parent = <&gpio0>;
interrupts = <RK_PA0 IRQ_TYPE_EDGE_FALLING>;
pinctrl-0 = <&bt_en>, <&bt_wake_host>, <&bt_wake>;
pinctrl-names = "default";
shutdown-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
};
};
&usbdp_phy0 {
status = "okay";
};
&usbdp_phy1 {
status = "okay";
};
&usb_host0_xhci {
dr_mode = "host";
status = "okay";
};
&usb_host1_xhci {
dr_mode = "host";
status = "okay";
};
&vop_mmu {
status = "okay";
};
&vop {
status = "okay";
};
&vp0 {
vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
reg = <ROCKCHIP_VOP2_EP_HDMI0>;
remote-endpoint = <&hdmi0_in_vp0>;
};
};
Reference in New Issue View Git Blame Copy Permalink