mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
synced 2025-08-31 22:23:05 +00:00
f8ed8fd084
Add the PMI8950 LAB-IBB regulator nodes, with the PMI8998 compatible as fallback. The LAB-IBB regulators are used as panels supplies on existing phones or tablets. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20241115-topic-sdm450-upstream-lab-ibb-v1-1-8a8e74befbfe@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
123 lines
2.6 KiB
Plaintext
123 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
// Copyright (c) 2019, AngeloGioacchino Del Regno <kholk11@gmail.com>
|
|
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
&spmi_bus {
|
|
pmic@2 {
|
|
compatible = "qcom,pmi8950", "qcom,spmi-pmic";
|
|
reg = <0x2 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pmi8950_vadc: adc@3100 {
|
|
compatible = "qcom,spmi-vadc";
|
|
reg = <0x3100>;
|
|
interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
|
|
channel@0 {
|
|
reg = <VADC_USBIN>;
|
|
qcom,pre-scaling = <1 4>;
|
|
label = "usbin";
|
|
};
|
|
|
|
channel@1 {
|
|
reg = <VADC_DCIN>;
|
|
qcom,pre-scaling = <1 4>;
|
|
label = "dcin";
|
|
};
|
|
|
|
channel@2 {
|
|
reg = <VADC_VCHG_SNS>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "vchg_sns";
|
|
};
|
|
|
|
channel@9 {
|
|
reg = <VADC_REF_625MV>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "ref_625mv";
|
|
};
|
|
|
|
channel@a {
|
|
reg = <VADC_REF_1250MV>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "ref_1250mv";
|
|
};
|
|
|
|
channel@d {
|
|
reg = <VADC_SPARE2>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "chg_temp";
|
|
};
|
|
};
|
|
|
|
pmi8950_mpps: mpps@a000 {
|
|
compatible = "qcom,pmi8950-mpp", "qcom,spmi-mpp";
|
|
reg = <0xa000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pmi8950_mpps 0 0 4>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pmi8950_gpios: gpio@c000 {
|
|
compatible = "qcom,pmi8950-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pmi8950_gpios 0 0 2>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
};
|
|
|
|
pmic@3 {
|
|
compatible = "qcom,pmi8950", "qcom,spmi-pmic";
|
|
reg = <0x3 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
labibb {
|
|
compatible = "qcom,pmi8950-lab-ibb",
|
|
"qcom,pmi8998-lab-ibb";
|
|
|
|
ibb: ibb {
|
|
interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>,
|
|
<0x3 0xdc 0x0 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-names = "sc-err", "ocp";
|
|
};
|
|
|
|
lab: lab {
|
|
interrupts = <0x3 0xde 0x1 IRQ_TYPE_EDGE_RISING>,
|
|
<0x3 0xde 0x0 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-names = "sc-err", "ocp";
|
|
};
|
|
};
|
|
|
|
pmi8950_pwm: pwm {
|
|
compatible = "qcom,pmi8950-pwm";
|
|
#pwm-cells = <2>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
pmi8950_wled: leds@d800 {
|
|
compatible = "qcom,pmi8950-wled";
|
|
reg = <0xd800>, <0xd900>;
|
|
interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
|
|
<0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
|
|
interrupt-names = "ovp", "short";
|
|
label = "backlight";
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|