Proxmox-Port/linux-loongson
1
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson synced 2025-09-01 15:14:52 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
loongarch-next
linux-loongson/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
Krzysztof Kozlowski 5dfdedf0de arm64: dts: allwinner: drop underscore in node names 
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.  Use also generic name for pwrseq
node, because generic naming is favored by Devicetree spec.  All the
clocks affected by this change use clock-output-names, so resulting
clock name should not change.  Functional impact checked with comparing
before/after DTBs with dtx_diff and fdtdump.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2024-04-15 23:09:55 +02:00

383 lines
6.7 KiB
Plaintext
Raw Permalink Blame History

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (c) 2016 ARM Ltd.
/dts-v1/;
#include "sun50i-a64.dtsi"
#include "sun50i-a64-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "BananaPi-M64";
compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "bananapi-m64:red:pwr";
gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
default-state = "on";
};
led-1 {
label = "bananapi-m64:green:user";
gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
};
led-2 {
label = "bananapi-m64:blue:user";
gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
};
};
wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "ext_clock";
};
};
&codec {
status = "okay";
};
&codec_analog {
cpvdd-supply = <&reg_eldo1>;
status = "okay";
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&cpu1 {
cpu-supply = <&reg_dcdc2>;
};
&cpu2 {
cpu-supply = <&reg_dcdc2>;
};
&cpu3 {
cpu-supply = <&reg_dcdc2>;
};
&dai {
status = "okay";
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii-id";
phy-handle = <&ext_rgmii_phy>;
phy-supply = <&reg_dc1sw>;
status = "okay";
};
&hdmi {
hvcc-supply = <&reg_dldo1>;
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&i2c1 {
status = "okay";
};
&i2c1_pins {
bias-pull-up;
};
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <&reg_dcdc1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
disable-wp;
bus-width = <4>;
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&reg_dldo2>;
vqmmc-supply = <&reg_dldo4>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&r_pio>;
interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
interrupt-names = "host-wake";
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
vmmc-supply = <&reg_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&r_rsb {
status = "okay";
axp803: pmic@3a3 {
compatible = "x-powers,axp803";
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
};
};
#include "axp803.dtsi"
&ac_power_supply {
status = "okay";
};
&battery_power_supply {
status = "okay";
};
&reg_aldo1 {
/*
* This regulator also drives the PE pingroup GPIOs,
* which also controls two LEDs.
*/
regulator-always-on;
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "afvcc-csi";
};
&reg_aldo2 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-pl";
};
&reg_aldo3 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-pll-avcc";
};
&reg_dc1sw {
/*
* This regulator also indirectly drives the PD pingroup GPIOs,
* which also controls the power LED.
*/
regulator-always-on;
regulator-name = "vcc-phy";
};
&reg_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-3v3";
};
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1040000>;
regulator-max-microvolt = <1300000>;
regulator-name = "vdd-cpux";
};
/* DCDC3 is polyphased with DCDC2 */
&reg_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vcc-dram";
};
&reg_dcdc6 {
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-sys";
};
&reg_dldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-hdmi-dsi";
};
&reg_dldo2 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
&reg_dldo4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi-io";
};
&reg_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
&reg_eldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "cpvdd";
};
&reg_fldo1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vcc-1v2-hsic";
};
/*
* The A64 chip cannot work without this regulator off, although
* it seems to be only driving the AR100 core.
* Maybe we don't still know well about CPUs domain.
*/
&reg_fldo2 {
regulator-always-on;
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpus";
};
&reg_rtc_ldo {
regulator-name = "vcc-rtc";
};
&simplefb_hdmi {
vcc-hdmi-supply = <&reg_dldo1>;
};
&sound {
status = "okay";
simple-audio-card,widgets = "Headphone", "Headphone Jack",
"Microphone", "Microphone Jack",
"Microphone", "Onboard Microphone";
simple-audio-card,routing =
"Left DAC", "DACL",
"Right DAC", "DACR",
"ADCL", "Left ADC",
"ADCR", "Right ADC",
"Headphone Jack", "HP",
"MIC2", "Microphone Jack",
"Onboard Microphone", "MBIAS",
"MIC1", "Onboard Microphone";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "brcm,bcm43438-bt";
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "lpo";
vbat-supply = <&reg_dldo2>;
vddio-supply = <&reg_dldo4>;
device-wakeup-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
host-wakeup-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
shutdown-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
};
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <&reg_drivevbus>;
status = "okay";
};
Reference in New Issue View Git Blame Copy Permalink