mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
synced 2025-08-30 21:52:21 +00:00
d21bbeee52
Add a compatible entry for the onsemi FSUSB42 USB switch, which can be used for switching orientation of the SBU lines in USB Type-C applications. Drivers work as-is with the existing fallback compatible. Link to datasheet: https://www.onsemi.com/pdf/datasheet/fsusb42-d.pdf Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20241212-x1e80100-qcp-dp-v1-1-37cb362a0dfe@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
116 lines
2.6 KiB
YAML
116 lines
2.6 KiB
YAML
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/usb/gpio-sbu-mux.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: GPIO-based SBU mux
|
|
|
|
maintainers:
|
|
- Bjorn Andersson <andersson@kernel.org>
|
|
|
|
description:
|
|
In USB Type-C applications the SBU lines needs to be connected, disconnected
|
|
and swapped depending on the altmode and orientation. This binding describes
|
|
a family of hardware solutions which switches between these modes using GPIO
|
|
signals.
|
|
|
|
properties:
|
|
compatible:
|
|
items:
|
|
- enum:
|
|
- nxp,cbdtu02043
|
|
- onnn,fsusb42
|
|
- onnn,fsusb43l10x
|
|
- pericom,pi3usb102
|
|
- ti,tmuxhs4212
|
|
- const: gpio-sbu-mux
|
|
|
|
enable-gpios:
|
|
description: Switch enable GPIO
|
|
|
|
select-gpios:
|
|
description: Orientation select
|
|
|
|
vcc-supply:
|
|
description: power supply
|
|
|
|
mode-switch: true
|
|
orientation-switch: true
|
|
|
|
port:
|
|
$ref: /schemas/graph.yaml#/properties/port
|
|
description:
|
|
A port node to link the SBU mux to a TypeC controller for the purpose of
|
|
handling altmode muxing and orientation switching.
|
|
|
|
required:
|
|
- compatible
|
|
- select-gpios
|
|
- orientation-switch
|
|
- port
|
|
|
|
allOf:
|
|
- $ref: usb-switch.yaml#
|
|
- if:
|
|
required:
|
|
- mode-switch
|
|
then:
|
|
required:
|
|
- enable-gpios
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
tcpm {
|
|
connector {
|
|
compatible = "usb-c-connector";
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
tcpm_hs_out: endpoint {
|
|
remote-endpoint = <&usb_hs_phy_in>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
tcpm_ss_out: endpoint {
|
|
remote-endpoint = <&usb_ss_phy_in>;
|
|
};
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
tcpm_sbu_out: endpoint {
|
|
remote-endpoint = <&sbu_mux_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
sbu-mux {
|
|
compatible = "pericom,pi3usb102", "gpio-sbu-mux";
|
|
|
|
enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
|
|
select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
|
|
|
|
mode-switch;
|
|
orientation-switch;
|
|
|
|
port {
|
|
sbu_mux_in: endpoint {
|
|
remote-endpoint = <&tcpm_sbu_out>;
|
|
};
|
|
};
|
|
};
|
|
...
|