mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
synced 2025-09-03 17:51:23 +00:00
12b3642b6c
Code expects array only with 2 items which should be checked.
But also item checking is not working as it should likely because of
incorrect items description.
Fixes: d50f974c4f ("dt-bindings: serial: Convert rs485 bindings to json-schema")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/820c639b9e22fe037730ed44d1b044cdb6d28b75.1726480384.git.michal.simek@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
66 lines
2.1 KiB
YAML
66 lines
2.1 KiB
YAML
# SPDX-License-Identifier: GPL-2.0
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/serial/rs485.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: RS485 serial communications
|
|
|
|
description: The RTS signal is capable of automatically controlling line
|
|
direction for the built-in half-duplex mode. The properties described
|
|
hereafter shall be given to a half-duplex capable UART node.
|
|
|
|
maintainers:
|
|
- Rob Herring <robh@kernel.org>
|
|
|
|
properties:
|
|
rs485-rts-delay:
|
|
description: prop-encoded-array <a b>
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|
items:
|
|
- description: Delay between rts signal and beginning of data sent in
|
|
milliseconds. It corresponds to the delay before sending data.
|
|
default: 0
|
|
maximum: 100
|
|
- description: Delay between end of data sent and rts signal in milliseconds.
|
|
It corresponds to the delay after sending data and actual release
|
|
of the line.
|
|
default: 0
|
|
maximum: 100
|
|
|
|
rs485-rts-active-high:
|
|
description: drive RTS high when sending (this is the default).
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-rts-active-low:
|
|
description: drive RTS low when sending (default is high).
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-rx-active-high:
|
|
description: Polarity of receiver enable signal (when separate from RTS).
|
|
True indicates active high (default is low).
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
linux,rs485-enabled-at-boot-time:
|
|
description: enables the rs485 feature at boot time. It can be disabled
|
|
later with proper ioctl.
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-rx-during-tx:
|
|
description: enables the receiving of data even while sending data.
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-term-gpios:
|
|
description: GPIO pin to enable RS485 bus termination.
|
|
maxItems: 1
|
|
|
|
rs485-rx-during-tx-gpios:
|
|
description: Output GPIO pin that sets the state of rs485-rx-during-tx. This
|
|
signal can be used to control the RX part of an RS485 transceiver. Thereby
|
|
the active state enables RX during TX.
|
|
maxItems: 1
|
|
|
|
additionalProperties: true
|
|
|
|
...
|