mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
synced 2025-09-01 06:39:05 +00:00
07e858e7e1
Convert the Maxim MAX3191x and similar GPIO binding to DT schema format. It's a straight forward conversion. Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/20250714202843.3011698-1-robh@kernel.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
105 lines
2.7 KiB
YAML
105 lines
2.7 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/gpio/maxim,max31910.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Maxim MAX3191x GPIO serializer
|
|
|
|
maintainers:
|
|
- Lukas Wunner <lukas@wunner.de>
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- maxim,max31910
|
|
- maxim,max31911
|
|
- maxim,max31912
|
|
- maxim,max31913
|
|
- maxim,max31953
|
|
- maxim,max31963
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
gpio-controller: true
|
|
|
|
'#gpio-cells':
|
|
const: 2
|
|
|
|
'#daisy-chained-devices':
|
|
description: Number of chips in the daisy-chain.
|
|
default: 1
|
|
|
|
maxim,modesel-gpios:
|
|
description:
|
|
GPIO pins to configure modesel of each chip. The number of GPIOs must
|
|
equal "#daisy-chained-devices" (if each chip is driven by a separate pin)
|
|
or 1 (if all chips are wired to the same pin).
|
|
|
|
maxim,fault-gpios:
|
|
description:
|
|
GPIO pins to read fault of each chip. The number of GPIOs must equal
|
|
"#daisy-chained-devices" or 1.
|
|
|
|
maxim,db0-gpios:
|
|
description:
|
|
GPIO pins to configure debounce of each chip. The number of GPIOs must
|
|
equal "#daisy-chained-devices" or 1.
|
|
|
|
maxim,db1-gpios:
|
|
description:
|
|
GPIO pins to configure debounce of each chip. The number of GPIOs must
|
|
equal "maxim,db0-gpios".
|
|
|
|
maxim,modesel-8bit:
|
|
description:
|
|
Boolean whether the modesel pin of the chips is pulled high (8-bit mode).
|
|
Use this if the modesel pin is hardwired and consequently
|
|
"maxim,modesel-gpios" cannot be specified. By default if neither this nor
|
|
"maxim,modesel-gpios" is given, the driver assumes that modesel is pulled
|
|
low (16-bit mode).
|
|
type: boolean
|
|
|
|
maxim,ignore-undervoltage:
|
|
description:
|
|
Boolean whether to ignore undervoltage alarms signaled by the
|
|
"maxim,fault-gpios" or by the status byte (in 16-bit mode). Use this if
|
|
the chips are powered through 5VOUT instead of VCC24V, in which case they
|
|
will constantly signal undervoltage.
|
|
type: boolean
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- gpio-controller
|
|
- '#gpio-cells'
|
|
|
|
allOf:
|
|
- $ref: /schemas/spi/spi-peripheral-props.yaml#
|
|
|
|
unevaluatedProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
spi {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
gpio@0 {
|
|
compatible = "maxim,max31913";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
maxim,modesel-gpios = <&gpio2 23>;
|
|
maxim,fault-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
|
|
maxim,db0-gpios = <&gpio2 25>;
|
|
maxim,db1-gpios = <&gpio2 26>;
|
|
|
|
spi-max-frequency = <25000000>;
|
|
};
|
|
};
|