Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201210212748.5849-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add proper modalias structures to let this driver load automatically if
compiled as module, because max14577 MFD driver creates MFD cells with
such compatible strings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210112139.5370-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes a couple of bugs in the DA9121 driver.
One in an uninialised string I forgot to remove when changing to of_parse_cb()
The other is an index for an optional DT property which overflows
Adam Ward (2):
regulator: da9121: Remove uninitialised string variable
regulator: da9121: Fix index used for DT property
drivers/regulator/da9121-regulator.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
--
1.9.1
There is a missing "return ret;" on this error path so we call
"da9121_check_device_type(i2c, chip);" which will end up dereferencing
"chip->regmap" and lead to an Oops.
Fixes: c860476b9e ("regulator: da9121: Add device variant regmaps")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/X85soGKnWAjPUA7a@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
When I use the axp20x chip to power my SDIO device on the 5.4 kernel,
the output voltage of DLDO2 is wrong. After comparing the register
manual and source code of the chip, I found that the mask bit of the
driver register of the port was wrong. I fixed this error by modifying
the mask register of the source code. This error seems to be a copy
error of the macro when writing the code. Now the voltage output of
the DLDO2 port of axp20x is correct. My development environment is
Allwinner A40I of arm architecture, and the kernel version is 5.4.
Signed-off-by: DingHua Ma <dinghua.ma.sz@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org>
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Link: https://lore.kernel.org/r/20201201001000.22302-1-dinghua.ma.sz@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support from RPMH regulators found in PM8350 and PM8350c PMICs
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201203071244.2652297-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_GPIOLIB is disabled, the declarations from linux/gpio/consumer.h
are not visible:
drivers/regulator/da9121-regulator.c:371:14: error: implicit declaration of function 'fwnode_gpiod_get_index' [-Werror,-Wimplicit-function-declaration]
ena_gpiod = fwnode_gpiod_get_index(of_fwnode_handle(np), "enable", 0,
^
drivers/regulator/da9121-regulator.c:372:7: error: use of undeclared identifier 'GPIOD_OUT_HIGH'
GPIOD_OUT_HIGH |
^
drivers/regulator/da9121-regulator.c:373:7: error: use of undeclared identifier 'GPIOD_FLAGS_BIT_NONEXCLUSIVE'
GPIOD_FLAGS_BIT_NONEXCLUSIVE,
Include this explicitly to help compile testing.
Fixes: 46c413d5bb ("regulator: da9121: Add support for device variants via devicetree")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201204165229.3754763-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following sparse warnings:
drivers/regulator/da9121-regulator.c:55:21: warning: symbol 'da9121_10A_2phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:63:21: warning: symbol 'da9121_6A_2phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:71:21: warning: symbol 'da9121_5A_1phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:79:21: warning: symbol 'da9121_3A_1phase_current' was not declared. Should it be static?
drivers/regulator/da9121-regulator.c:151:32: warning: symbol 'status_event_handling' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/1606994795-36182-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds interrupt handler for variants, and notifications for events; over
temperature/voltage/current. Because the IRQs are triggered by persisting
status, they must be masked and the status polled until clear, before the
IRQ can be enabled again.
Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/fe21796bbcbadff84a472a4cc581ae8fafc7f8f5.1606755367.git.Adam.Ward.opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NXP PF8100/PF8121A/PF8200 regulator driver.
PF8100/PF8121A/PF8200 is PMIC designed for highperformance
consumer applications. It features seven high efficiency buck,
four linear and one vsnvs regulators.
Tested in Engicam i.Core MX8M Mini SOM platform boards.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201130112329.104614-2-jagan@amarulasolutions.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Selectors lower than linear_min_sel should not be considered invalid.
Thus return zero in case _regulator_list_voltage(),
regulator_list_hardware_vsel() or regulator_list_voltage_table()
receives such selectors as argument.
Fixes: bdcd117757 ("regulator: core: validate selector against linear_min_sel")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1606325147-606-1-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel test robot reported the following build error:
All errors (new ones prefixed by >>):
xtensa-linux-ld: drivers/regulator/qcom-rpmh-regulator.o: in function `rpmh_regulator_vrm_get_voltage_sel':
qcom-rpmh-regulator.c:(.text+0x270): undefined reference to `rpmh_write'
xtensa-linux-ld: drivers/regulator/qcom-rpmh-regulator.o: in function `rpmh_regulator_send_request':
qcom-rpmh-regulator.c:(.text+0x2f2): undefined reference to `rpmh_write'
xtensa-linux-ld: drivers/regulator/qcom-rpmh-regulator.o: in function `rpmh_regulator_vrm_get_voltage_sel':
>> qcom-rpmh-regulator.c:(.text+0x274): undefined reference to `rpmh_write_async'
xtensa-linux-ld: drivers/regulator/qcom-rpmh-regulator.o: in function `rpmh_regulator_send_request':
qcom-rpmh-regulator.c:(.text+0x2fc): undefined reference to `rpmh_write_async'
Which is due to REGULATOR_QCOM_RPMH depending on
QCOM_RPMH || COMPILE_TEST. The problem is that QOM_RPMH can now
be a module, which in that case requires REGULATOR_QCOM_RPMH=m
to build.
However, if COMPILE_TEST is enabled, REGULATOR_QCOM_RPMH can be
set to =y while QCOM_RPMH=m which will cause build failures.
The fix here is to add (QCOM_RPMH=n && COMPILE_TEST) to the
dependency.
Feedback would be appreciated!
Cc: Todd Kjos <tkjos@google.com>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201123222359.103822-1-john.stultz@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a simple regulator based on SCMI Voltage Domain Protocol.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
----
v6 --> v7
- add proper blank lines between semantic blocks
- fix return value on error path of scmi_reg_is_enabled()
- use generic Failure message on err path of info_get()
- fix comment containing apostrophe
v3 --> v4
- using of_match_full_name core regulator flag
- avoid coccinelle falde complaints about pointer-sized allocations
v2 --> v3
- remove multiple linear mappings support
- removed duplicated voltage name printout
- added a few comments
- simplified return path in scmi_reg_set_voltage_sel()
v1 --> v2
- removed duplicate regulator naming
- removed redundant .get/set_voltage ops: only _sel variants implemented
- removed condexpr on fail path to increase readability
v0 --> v1
- fixed init_data constraint parsing
- fixes for v5.8 (linear_range.h)
- fixed commit message content and subject line format
- factored out SCMI core specific changes to distinct patch
- reworked Kconfig and Makefile to keep proper alphabetic order
- fixed SPDX comment style
- removed unneeded inline functions
- reworked conditionals for legibility
- fixed some return paths to properly report SCMI original errors codes
- added some more descriptive error messages when fw returns invalid ranges
- removed unneeded explicit devm_regulator_unregister from .remove()
Link: https://lore.kernel.org/r/20201123202336.46701-4-cristian.marussi@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
this series introduces the support for the new SCMI Voltage Domain Protocol
defined by the upcoming SCMIv3.0 specification, whose BETA release is
available at [1].
Afterwards, a new generic SCMI Regulator driver is developed on top of the
new SCMI VD Protocol.
In V4 Patch 3/5 introduced a needed fix in Regulator framework to cope with
generic named nodes.
The series is currently based on for-next/scmi [2] on top of:
commit b141fca08207 ("firmware: arm_scmi: Fix missing destroy_workqueue()")
Any feedback welcome,
Thanks,
Cristian
---
v5 --> v6
- reordered dt bindings patch
- removed single field struct
- reviewed args to scmi_init_voltage_levels()
- allocating scmi_voltage_info_array contiguously
v4 --> v5
- rebased
- VD Protocol
- removed inline
- moved segmented intervals defines
- fixed some macros complaints by checkpatch
v3 --> v4
- DT bindings
- using generic node names
- listing explicitly subset of supported regulators bindings
- SCMI Regulator
- using of_match_full_name core regulator flag
- avoid coccinelle false flag complaints
- VD Protocol
- avoid coccinelle false flag complaints
- avoiding fixed size typing
v2 --> v3
- DT bindings
- avoid awkard examples based on _cpu/_gpu regulators
- SCMI Regulator
- remove multiple linear mappings support
- removed duplicated voltage name printout
- added a few comments
- simplified return path in scmi_reg_set_voltage_sel()
- VD Protocol
- restrict segmented voltage domain descriptors to one triplet
- removed unneeded inline
- free allocated resources for invalid voltage domain
- added __must_check to info_get voltage operations
- added a few comments
- removed fixed size typing from struct voltage_info
v1 --> v2
- rebased on for-next/scmi v5.10
- DT bindings
- removed any reference to negative voltages
- SCMI Regulator
- removed duplicate regulator naming
- removed redundant .get/set_voltage ops: only _sel variants implemented
- removed condexpr on fail path to increase readability
- VD Protocol
- fix voltage levels query loop to reload full cmd description
between iterations as reported by Etienne Carriere
- ensure transport rx buffer is properly sized calli scmi_reset_rx_to_maxsz
between transfers
[1]:https://developer.arm.com/documentation/den0056/c/
[2]:https://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux.git/log/?h=for-next/scmi
Cristian Marussi (5):
firmware: arm_scmi: Add Voltage Domain Support
firmware: arm_scmi: add SCMI Voltage Domain devname
regulator: core: add of_match_full_name boolean flag
dt-bindings: arm: add support for SCMI Regulators
regulator: add SCMI driver
.../devicetree/bindings/arm/arm,scmi.txt | 43 ++
drivers/firmware/arm_scmi/Makefile | 2 +-
drivers/firmware/arm_scmi/common.h | 1 +
drivers/firmware/arm_scmi/driver.c | 3 +
drivers/firmware/arm_scmi/voltage.c | 380 ++++++++++++++++
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/of_regulator.c | 8 +-
drivers/regulator/scmi-regulator.c | 409 ++++++++++++++++++
include/linux/regulator/driver.h | 3 +
include/linux/scmi_protocol.h | 64 +++
11 files changed, 920 insertions(+), 3 deletions(-)
create mode 100644 drivers/firmware/arm_scmi/voltage.c
create mode 100644 drivers/regulator/scmi-regulator.c
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
During regulators registration, if .of_match and .regulators_node are
defined as non-null strings in struct regulator_desc the core searches the
DT subtree rooted at .regulators_node trying to match, at first, .of_match
against the 'regulator-compatible' property and, then, falling back to use
the name of the node itself to determine a good match.
Property 'regulator-compatible', though, is now deprecated and falling back
to match against the node name, works fine only as long as the involved
nodes are named in an unique way across the searched subtree; if that's not
the case, like when using <common-name>@<unit> style naming for properties
indexed via 'reg' property (as advised by the standard), the above matching
mechanism based on the simple common name will lead to multiple matches and
the only viable alternative would be to properly define the now deprecated
'regulator-compatible' as the node full name, i.e. <common-name>@<unit>.
In order to address this case without using such deprecated binding, define
a new boolean flag .of_match_full_name in struct regulator_desc to force
the core to match against the node full-name instead of the plain name.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20201119191051.46363-4-cristian.marussi@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efe ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
This series adds support for ramp delay on mcp16502. It also adds
some cleanup on mcp16502.
Apart from that patches 1/6 fixes the selector validation in case
the regulator::desc::linear_min_sel is not zero.
Thank you,
Claudiu Beznea
Changes in v3:
- fix compilation error in patch 5/6
Reported-by: kernel test robot <lkp@intel.com>
Changes in v2:
- rebase on top of regulator/for-next
- checked 1/6 and 3/6 applies on top of regulator/for-5.10
Claudiu Beznea (6):
regulator: core: validate selector against linear_min_sel
regulator: core: do not continue if selector match
regulator: mcp16502: add linear_min_sel
regulator: mcp16502: adapt for get/set on other registers
regulator: mcp16502: add support for ramp delay
regulator: mcp16502: remove void documentation of struct mcp16502
drivers/regulator/core.c | 12 +++-
drivers/regulator/helpers.c | 3 +-
drivers/regulator/mcp16502.c | 135 ++++++++++++++++++++++++++++++++++++-------
3 files changed, 127 insertions(+), 23 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
There are regulators who's min selector is not zero. Selectors loops
(looping b/w zero and regulator::desc::n_voltages) might throw errors
because invalid selectors are used (lower than
regulator::desc::linear_min_sel). For this situations validate selectors
against regulator::desc::linear_min_sel.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605280870-32432-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MCP16502 have multiple registers for each regulator (as described
in enum mcp16502_reg). Adapt the code to be able to get/set all these
registers. This is necessary for the following commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605280870-32432-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Workaround regulators whose supply name happens to be the same as its
own name. This fixes boards that used to work before the early supply
resolving was removed. The error message is left in place so that
offending drivers can be detected.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/d703acde2a93100c3c7a81059d716c50ad1b1f52.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator's name equals its supply's name the
regulator_resolve_supply() recurses indefinitely. Add a check
so that debugging the problem is easier. The "fixed" commit
just exposed the problem.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/c6171057cfc0896f950c4d8cb82df0f9f1b89ad9.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed commit introduced a possible second call to
set_machine_constraints() and that allocates memory for
rdev->constraints. Move the allocation to the caller so
it's easier to manage and done once.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/78c3d4016cebc08d441aad18cb924b4e4d9cf9df.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Limit the fsl,pfuze-support-disable-sw to the pfuze100 and pfuze200
variants.
When enabling fsl,pfuze-support-disable-sw and using a pfuze3000 or
pfuze3001, the driver would choose pfuze100_sw_disable_regulator_ops
instead of the newly introduced and correct pfuze3000_sw_regulator_ops.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Fixes: 6f1cf5257a ("regualtor: pfuze100: correct sw1a/sw2 on pfuze3000")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201110174113.2066534-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
RFC for adding a support for typical voltage scaling connection
In few occasions there has been a need to scale the voltage output
from bucks on BD71837. Usually this is done when buck8 is used to
power specific GPU which can utilize voltages down to 0.7V. As lowest
the buck8 on BD71837 can go is 0.8V, and external connection is used to
scale the voltages.
The BD71837, BD71847 and BD71850 bucks can be adjusted by pulling up the
feedback pin using suitable voltage/resistors.
|---------------|
| buck 8 |-------+----->Vout
| | |
|---------------| |
| |
| |
+-------+--R2----+
|
R1
|
V FB-pull-up
This will scale the voltage as follows:
- Vout_o = Vo - (Vpu - Vo)*R2/R1
- Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
>From HW point of view this does not need to be limited to buck 8. This
connection can be used to adjust output from any of the bucks on
BD71837/47/50.
As this seems to be a 'de-facto' way to scale the voltages on BD71837 it
might be a good idea to support computing the new voltage ranges for
bucks based on the V-pull-up and resistor R1/R2 values given from
device-tree. This allows describing the external HW connection using DT
to correctly scale the voltages.
This RFC uses "rohm,feedback-pull-up-r1-ohms" and
"rohm,feedback-pull-up-r2-ohms" to provide the resistor values - but
these names (without the picture) might not be too descriptive. I am
grateful for all suggestions as better and more descriptive names.
This patch series is an RFC because this connection feels somewhat
"hacky". OTOH - when hack becomes widely used, it is less of an hack and
more of a standard - and occasionally supporting HW hacks using SW may
benefit us all, right? :)
The other thing some projects do is allowing the change of BD71837 buck8
voltages when buck8 is enabled. This however will introduce voltage
spikes as buck8 was not originally designed for this. The specific HW
platform must be evaluated to be able to tolerate these spikes. Thus
this patch series does not support buck8 voltage changes when buck8 is
enabled. I wonder if this should be allowed per some config option(?) I
don't want to help people frying their boards... Opinions? Is there
suggested way of allowing this type of features at own risk? Config or
even Some #ifdef which is not listed in Kconfig? Device-tree property?
If you have (good) suggestions I could add the optional (non default)
DVS support for non DVS bucks on BD71837.
Matti Vaittinen (3):
dt-bindings: regulator: BD71837 support commonly used feedback
connection
dt-bindings: regulator: BD71847 support commonly used feedback
connection
regulator: bd718x7: Support external connection to scale voltages
.../regulator/rohm,bd71837-regulator.yaml | 48 +++++
.../regulator/rohm,bd71847-regulator.yaml | 49 ++++++
drivers/regulator/bd718x7-regulator.c | 164 +++++++++++++++++-
3 files changed, 254 insertions(+), 7 deletions(-)
base-commit: 3cea11cd5e
--
2.21.3
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
Setups where regulator (especially the buck8) output voltage is scaled
by adding external connection where some other regulator output is
connected to feedback-pin (over suitable resistors) is getting popular
amongst users of BD71837. This allows for example scaling down the
buck8 voltages to suit lover GPU voltages for projects where buck8 is
(ab)used to supply power for GPU. As a note - some setups do allow DVS
for buck8. This do produce voltage spikes and the HW must be evaluated
to be able to survive them. Thus this commit still keep the DVS disabled
for non DVS bucks by default. Let's not help you burn your proto board.
Allow describing this external connection from DT and scale the
voltages accordingly. This is what the connection should look like:
|------------|
| buck 8 |-------+----->Vout
| | |
|------------| |
| FB pin |
| |
+-------+--R2---+
|
R1
|
V FB-pull-up
Here the buck output is sifted according to formula:
Vout_o = Vo - (Vpu - Vo)*R2/R1
Linear_step = step_orig*(R1+R2)/R1
where:
Vout_o is adjusted voltage output at vsel reg value 0
Vo is original voltage output at vsel reg value 0
Vpu is the pull-up voltage V FB-pull-up in the picture
R1 and R2 are resistor values.
Bring support for specifying the Vpu, R1 and R2 from device tree and
scale voltages if they are given.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/89b2be87074f307a8823f15f34e1f662023cbf36.1604994184.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In regulator_late_cleanup when is_enabled failed, don't try to disable
the regulator since it would likely to fail too and causing confusing
error messages.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Link: https://lore.kernel.org/r/20201106064817.3290927-1-pihsun@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the Dialog Semiconductor DA9121, a single-channel
dual-phase buck converter controlled via I2C.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20201103100021.19603-3-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_get_voltage_rdev() is called in regulator probe() when
applying machine constraints. The "fixed" commit exposed the problem
that non-bypassed regulators can forward the request to its parent
(like bypassed ones) supply. Return -EPROBE_DEFER when the supply
is expected but not resolved yet.
Fixes: aea6cb9970 ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-by: Ondřej Jirman <megous@megous.com>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Ondřej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/a9041d68b4d35e4a2dd71629c8a6422662acb5ee.1604351936.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
On SM8250 MDSS_GDSC (and the rest of display clock controller) is
supplied power by MMCX power domain. Handle this link in GDSC code by
binding the power domain in dts file.
This patchset depends on [1]
Changes since v1:
- Define fixed-regulator-domain regulator using power domain
performance state for enabling/disabling.
- Rework to use new fixed regulator type (fixed-regulator-domain)
instead of controlling power domain directly from gdsc code.
Changes since RFC:
- Fix naming of gdsc_supply_on/gdsc_supply_off functions
- Fix detaching of solo gdsc's power domain in error handling code
- Drop the dts patch, as respective display nodes are still not
submitted to the mailing list.
[1]
https://lore.kernel.org/linux-arm-msm/20200927190653.13876-1-jonathan@marek.ca/
Don't populate const array lp872x_num_regulators on the stack but
instead make it static. Makes the object code smaller by 29 bytes.
Before:
text data bss dec hex filename
18441 4624 64 23129 5a59 drivers/regulator/lp872x.o
After:
text data bss dec hex filename
18316 4720 64 23100 5a3c drivers/regulator/lp872x.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201016222235.686981-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds possibility to choose the compatible "fixed-regulator-domain" for
regulators which use power domain for enabling/disabling corresponding
regulator.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201023131925.334864-3-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8953 is commonly used on board with MSM8953 SoCs or its variants:
APQ8053, SDM(SDA)450 and SDM(SDA)632.
It provides 7 SMPS and 23 LDO regulators.
Signed-off-by: Vladimir Lypak <junak.pub@gmail.com>
Link: https://lore.kernel.org/r/20201004083413.324351-1-junak.pub@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If debugging is disabled, print_constraints() does not print the actual
constraints, but still performs some processing and string formatting,
only to throw away the result later.
Fix this by moving all constraint debug processing to a separate
function, and replacing it by a dummy when debugging is disabled.
This reduces kernel size by almost 800 bytes (on arm/arm64).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201005131546.22448-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno <kholk11@gmail.com>:
From: AngeloGioacchino Del Regno <kholk11@gmail.com>
This patch series enables support for the regulators as found in
the PM660 and PM660L PMICs.
While at it, and to make them work, along with other regulators
for other qcom PMICs, enlarge the maximum property name length in
the regulator core, so that we're able to correctly parse the
supply parents, which have got very long names (details in patch 1/5).
This patch series has been tested against the following devices:
- Sony Xperia XA2 Ultra (SDM630 Nile Discovery)
- Sony Xperia 10 (SDM630 Ganges Kirin)
- Sony Xperia 10 Plus (SDM636 Ganges Mermaid)
AngeloGioacchino Del Regno (7):
regulator: core: Enlarge max OF property name length to 64 chars
regulator: qcom_spmi: Add support for new regulator types
regulator: qcom_spmi: Add PM660/PM660L regulators
regulator: dt-bindings: Document the PM660/660L SPMI PMIC entries
regulator: qcom_smd: Add PM660/PM660L regulator support
mfd: qcom-spmi-pmic: Add support for PM660/PM660L
regulator: dt-bindings: Document the PM660/PM660L PMICs entries
.../regulator/qcom,smd-rpm-regulator.yaml | 7 ++
.../regulator/qcom,spmi-regulator.txt | 31 +++++
drivers/mfd/qcom-spmi-pmic.c | 4 +
drivers/regulator/core.c | 4 +-
drivers/regulator/qcom_smd-regulator.c | 113 ++++++++++++++++++
drivers/regulator/qcom_spmi-regulator.c | 107 +++++++++++++++++
include/linux/soc/qcom/smd-rpm.h | 4 +
7 files changed, 268 insertions(+), 2 deletions(-)
--
2.28.0
The only usage of qcom_labibb_ops is to assign it to the ops field in
the regulator_desc struct, which is a const pointer. The only usage of
pmi8998_lab_desc and pmi8998_ibb_desc is to assign their address to the
desc field in the labibb_regulator_data struct which can be made const,
since it is only copied into the desc field in the
labbibb_regulator_data struct. This struct is modified, but that's a
copy of the static one. Make them const to allow the compiler to put
them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200930162602.18583-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM660 and PM660L are a very very common PMIC combo, found on
boards using the SDM630, SDM636, SDM660 (and SDA variants) SoC.
PM660 provides 6 SMPS and 19 LDOs (of which one is unaccesible),
while PM660L provides 5 SMPS (of which S3 and S4 are combined),
10 LDOs and a Buck-or-Boost (BoB) regulator.
The PM660L IC also provides other regulators that are very
specialized (for example, for the display) and will be managed
in the other appropriate drivers (for example, labibb).
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-6-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM660 PMIC is very often paired with the PM660L option on
SDM630/663/660 (and SDA variants) boards.
The PM660 has 11 "660" LDOs (2 NMOS, 9 PMOS) and 7 HT LDOs (4 NMOS,
3 PMOS) and a quirk: the L4 regulator is unaccessible or does not
exist on the PMIC.
The PM660L has 8 "660" LDOs (1 NMOS, 7 PMOS) and 2 HT NMOS LDOs.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-4-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the support for some regulator types that are
missing in this driver, such as the ht nmos-ldo, ht-lv nmos-ldo
and new gen n/pmos-ldo, all belonging to the FTSMPS426 register
layout.
This is done in preparation for adding support for the PM660 and
PM660L PMICs.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-3-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulator drivers may be defining very long names: this is the
case with the qcom_smd and qcom_spmi regulators, where we need to
parse the regulator parents from DT.
For clarity, this is an example:
{ "l13a", QCOM_SMD_RPM_LDOA, 13, &pm660_ht_lvpldo,
"vdd_l8_l9_l10_l11_l12_l13_l14" },
pm660-regulators {
...
vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>
...
};
Now, with a 32 characters limit, the function is trying to parse,
exactly, "vdd_l8_l9_l10_l11_l12_l13_l14-s" (32 chars) instead of
the right one, which is 37 chars long in this specific case.
... And this is not only the case with PM660/PM660L, but also with
PMA8084, PM8916, PM8950 and others that are not implemented yet.
The length of 64 chars was chosen based on the longest parsed property
name that I could find, which is in PM8916, and would be 53 characters
long.
At that point, rounding that to 64 looked like being the best idea.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20200926125549.13191-2-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
1. Add vendor suffix to all proprietary properties.
2. Fix typo.
3. Change lsw to normal property, not pattern property.
4. Due to item 1, modify source code for property parsing.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1601460480-4259-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Three simple patches to aid in debugging regulators.
Michał Mirosław (3):
regulator: print state at boot
regulator: print symbolic errors in kernel messages
regulator: resolve supply after creating regulator
drivers/regulator/core.c | 124 ++++++++++++++++++++++-----------------
1 file changed, 69 insertions(+), 55 deletions(-)
--
2.20.1
When creating a new regulator its supply cannot create the sysfs link
because the device is not yet published. Remove early supply resolving
since it will be done later anyway. This makes the following error
disappear and the symlinks get created instead.
DCDC_REG1: supplied by VSYS
VSYS: could not add device link regulator.3 err -2
Note: It doesn't fix the problem for bypassed regulators, though.
Fixes: 45389c4752 ("regulator: core: Add early supply resolution for regulators")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/ba09e0a8617ffeeb25cb4affffe6f3149319cef8.1601155770.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
A single fix for incorrect specification of some of the register fields
on axp20x devices which would break voltage setting on affected systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uTFQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OEZB/9tRSg6gHVdp2OwAbWPzJQcHYYP4stQ
H3mPcsDJRmpVnHhUQe3qlUvG4QZ7bDhnHFYS1G7LFgEBNVhCwKtpnseaQMJaCaa+
t9LLWNtzltuo75995bBtPYcSQI6U0yUYbu7U7n+4vibh/pjqY3eNg4lLrWtVL/OC
FwkCEql5+ZTTg3OcRHzKlYe1UlOB0kSHNCjySiVytPrC0UH32gFCs/LSZxDR8lbo
a9x8Vi8brbcmpASoCY0d+c0hM6PWB/chNwVHGnoWYJ+xoJMVLzC8TN/mkUgG++9i
wnwXfbUd0EbLKuLrZto0qdx14n2nLp2YpeLJhTbsJaQ5C+FQGvv7D2v5
=Uvnh
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"A single fix for incorrect specification of some of the register
fields on axp20x devices which would break voltage setting on affected
systems"
* tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: axp20x: fix LDO2/4 description
Currently we wrongly set the mask of value of LDO2/4 both to the mask of
LDO2, and the LDO4 voltage configuration is left untouched. This leads
to conflict when LDO2/4 are both in use.
Fix this issue by setting different vsel_mask to both regulators.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Link: https://lore.kernel.org/r/20200923005142.147135-1-icenowy@aosc.io
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was using subsys_initcall() because in old times deferred
probe was not supported everywhere and specific ordering was needed.
Since probe deferral works fine and specific ordering is discouraged
(hides dependencies between drivers and couples their boot order), the
driver can be converted to regular module_platform_driver.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200921203616.19623-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of Maxim and Samsung PMIC/MUIC regulator drivers can be compile
tested to increase build coverage. This allows to build them on
configurations without I2C (as I2C is required by dependency - parent
MFD driver).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200920214107.6299-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial support for ROHM BD9576MUF and BD9573MUF PMICs.
These PMICs are primarily intended to be used to power the R-Car family
processors. BD9576MUF includes some additional safety features the
BD9573MUF does not have. This initial version of drivers does not
utilize these features and for now the SW behaviour is identical.
Please note that this version of drivers is only tested on BD9576MUF
but according to the data-sheets the relevant parts of registers should
be same so drivers should also work on BD9573MUF.
This patch series includes MFD, watchdog and regulator drivers with
basic functionality such as:
- Enabling and pinging the watchdog
- configuring watchog timeout / window from device-tree
- reading regulator states/voltages
- enabling/disabling VOUT1 (VD50) when control mode B is used.
This patch series does not bring interrupt support. BD9576MUF and BD9573MUF
are designed to keep the IRQ line low for whole duration of error
condition. IRQ can't be 'acked'. So proper IRQ support would require
some IRQ limiter implementation (delayed unmask?) in order to not hog
the CPU.
---
Matti Vaittinen (6):
dt_bindings: mfd: Add ROHM BD9576MUF and BD9573MUF PMICs
dt_bindings: regulator: Add ROHM BD9576MUF and BD9573MUF PMICs
mfd: Support ROHM BD9576MUF and BD9573MUF
wdt: Support wdt on ROHM BD9576MUF and BD9573MUF
regulator: Support ROHM BD9576MUF and BD9573MUF
MAINTAINERS: Add ROHM BD9576MUF and BD9573MUF drivers
.../bindings/mfd/rohm,bd9576-pmic.yaml | 129 +++++++
.../regulator/rohm,bd9576-regulator.yaml | 33 ++
MAINTAINERS | 4 +
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rohm-bd9576.c | 130 +++++++
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd9576-regulator.c | 337 ++++++++++++++++++
drivers/watchdog/Kconfig | 13 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/bd9576_wdt.c | 295 +++++++++++++++
include/linux/mfd/rohm-bd957x.h | 61 ++++
include/linux/mfd/rohm-generic.h | 2 +
14 files changed, 1028 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd9576-pmic.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml
create mode 100644 drivers/mfd/rohm-bd9576.c
create mode 100644 drivers/regulator/bd9576-regulator.c
create mode 100644 drivers/watchdog/bd9576_wdt.c
create mode 100644 include/linux/mfd/rohm-bd957x.h
base-commit: f4d51dffc6
--
2.21.0
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
The only usage of ti_abb_reg_ops is to assign its address to the ops
field in the regulator_desc struct, which is a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200913084114.8851-6-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usages of these is to assign their address to the ops field in
the regulator_desc struct, which is a const pointer. Make them const to
allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200913084114.8851-5-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of stw481x_vmmc_ops is to assign its address to the ops
field in the regulator_desc struct which is a const pointer.
The only usage of vmmc_regulator is to pass its address to
of_get_regulator_init_data() and devm_regulator_register(), both which
take const pointers.
Make both of them const to allow the compiler to put them in read-only
memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200913084114.8851-4-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of fixed_voltage_ops and fixed_voltage_clkenabled_ops is
to assign their address the ops field in the regulator_desc struct,
which is a const pointer. Make them const to allow the compiler to put
them in read-only memory.
make them const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200913084114.8851-3-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of dummy_initdata is to assign its address to the
init_data field of the regulator_config struct and the only usage
dummy_ops is to assign its address to the ops field in the
regulator_desc struct, both which are const pointers. Make them const to
allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200913084114.8851-2-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The biggest set of fixes here is those from Michał Mirosław fixing some
locking issues with coupled regulators that are triggered in cases where
a coupled regulator is used by a device involved in fs_reclaim like eMMC
storage. These are relatively serious for the affected systems, though
the circumstances where they trigger are very rare.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9baDITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NAOCACGwc1Rxsr9cMDY5vQS7AHzfPVRdoQJ
Z9KIOQT9ER0hFHRNh1/t1n/p4DcK+3ke0MH/R/VndijvePJgHyL01Bsjq92iDiIy
b80nDJwRwLWWdvKAPG5JklVK8pL/6LxaC9eL8zK93Hm4fGkNJzBi7jF2++jep/tB
2jRM4Vrq8B0dkh/jPQMscl4Z66purIiyKLJjy1QFjXXq0/jkjZizURy+aofS3uJD
0vebim9OI7z0H4g6cflJrHUAuDraNmGCfGAyUMH7AESJlUGNRk7BzNYT51tLVYqG
ithNZDh/AbWhGzntuUUKNlM4D8p26FNJmU51crh33kBH3va737dvc/BT
=3fwP
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The biggest set of fixes here is those from Michał Mirosław fixing
some locking issues with coupled regulators that are triggered in
cases where a coupled regulator is used by a device involved in
fs_reclaim like eMMC storage.
These are relatively serious for the affected systems, though the
circumstances where they trigger are very rare"
* tag 'regulator-fix-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pwm: Fix machine constraints application
regulator: core: Fix slab-out-of-bounds in regulator_unlock_recursive()
regulator: remove superfluous lock in regulator_resolve_coupling()
regulator: cleanup regulator_ena_gpio_free()
regulator: plug of_node leak in regulator_register()'s error path
regulator: push allocation in set_consumer_device_supply() out of lock
regulator: push allocations in create_regulator() outside of lock
regulator: push allocation in regulator_ena_gpio_request() out of lock
regulator: push allocation in regulator_init_coupling() outside of lock
regulator: fix spelling mistake "Cant" -> "Can't"
regulator: cros-ec-regulator: Add NULL test for devm_kmemdup call
Fix sparse warnings:
drivers/regulator/bd718x7-regulator.c:576:28: warning: symbol 'bd71847_swcontrol_ops' was not declared. Should it be static?
drivers/regulator/bd718x7-regulator.c:585:28: warning: symbol 'bd71847_hwcontrol_ops' was not declared. Should it be static?
drivers/regulator/bd718x7-regulator.c:902:28: warning: symbol 'bd71837_swcontrol_ops' was not declared. Should it be static?
drivers/regulator/bd718x7-regulator.c:913:28: warning: symbol 'bd71837_hwcontrol_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200910034240.37268-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This removes regulator_lock/unlock() calls around
regulator_notifier_call_chain() as they are redundant - drivers
already have to guarantee regulator_dev's existence during the call.
This should make reasoing about the lock easier, as this was the only
use outside regulator core code.
The only client that needed recursive locking from the notifier chain
was drivers/usb/host/ohci-da8xx.c, which responds to over-current
notification by calling regulator_disable().
Michał Mirosław (3):
regulator: don't require mutex for regulator_notifier_call_chain()
regulator: remove locking around regulator_notifier_call_chain()
regulator: unexport regulator_lock/unlock()
drivers/regulator/core.c | 11 +++--------
drivers/regulator/da9055-regulator.c | 2 --
drivers/regulator/da9062-regulator.c | 2 --
drivers/regulator/da9063-regulator.c | 2 --
drivers/regulator/da9210-regulator.c | 4 ----
drivers/regulator/da9211-regulator.c | 4 ----
drivers/regulator/lp8755.c | 6 ------
drivers/regulator/ltc3589.c | 10 ++--------
drivers/regulator/ltc3676.c | 10 ++--------
drivers/regulator/pv88060-regulator.c | 10 ++--------
drivers/regulator/pv88080-regulator.c | 10 ++--------
drivers/regulator/pv88090-regulator.c | 10 ++--------
drivers/regulator/slg51000-regulator.c | 4 ----
drivers/regulator/stpmic1_regulator.c | 4 ----
drivers/regulator/wm831x-dcdc.c | 4 ----
drivers/regulator/wm831x-isink.c | 2 --
drivers/regulator/wm831x-ldo.c | 2 --
drivers/regulator/wm8350-regulator.c | 2 --
include/linux/regulator/driver.h | 3 ---
19 files changed, 13 insertions(+), 89 deletions(-)
--
2.20.1
In the case of an unrecognised mini-card the Lochnagar will not
initialise the VDDCORE voltage register leading to a value outside of the
current range. Add an additional range to cover these values, initially
this wasn't done since they are duplicates of the existing minimum
value.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200904122506.28017-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_notifier_call_chain() doesn't need rdev lock and rdev's
existence is assumed in the code anyway. Remove the locks from drivers.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/42393f66dcc4d80dcd9797be45216b4035aa96cb.1597032945.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 3801b86aa4 ("regulator: Refactor supply implementation
to work as regular consumers") we no longer cascade notifications
and so notifier head's built-in rwsem is enough to protect the
notifier chain. Remove the requirement to fix one case where
rdev->mutex might be forced to be taken recursively.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/5a0da9017c69a4dbc3f9b50f44476fce80a73387.1597032945.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD718(37/47/50) regulator enable states can be controlled
either by SW or by PMIC internal state machine. The bd718x7
driver has not supported leaving the regulators under HW state
machine control (except for cases where this is required to
avoid boot-up problems due to critical regulators being turned
OFF at reset when SNVS used as reset state).
On some systems this is undesirable as there now are setups where
mixture of SW and HW state machine controlled regulators is needed.
Specifically, some SoCs signal SUSPEND state change to PMIC via
STBY_REQ line. Now there are setups that expect certain regulators
then to be disabled (by PMIC state machine) while other regulators
should stay enabled (regardless of HW state => SW control required).
Add support for a new device-tree property
"rohm,no-regulator-enable-control" which can be used to leave
regulator(s) under HW state machine control.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/6ebba33dd08f2dcc9f1137bbff4d2dc905278a5a.1599029335.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the zero duty cycle doesn't correspond to any voltage in the voltage
table, the PWM regulator returns an -EINVAL from get_voltage_sel() which
results in the core erroring out with a "failed to get the current
voltage" and ending up not applying the machine constraints.
Instead, return -ENOTRECOVERABLE which makes the core set the voltage
since it's at an unknown value.
For example, with this device tree:
fooregulator {
compatible = "pwm-regulator";
pwms = <&foopwm 0 100000>;
regulator-min-microvolt = <2250000>;
regulator-max-microvolt = <2250000>;
regulator-name = "fooregulator";
regulator-always-on;
regulator-boot-on;
voltage-table = <2250000 30>;
};
Before this patch:
fooregulator: failed to get the current voltage(-22)
After this patch:
fooregulator: Setting 2250000-2250000uV
fooregulator: 2250 mV
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20200902130952.24880-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of these is to assign their address to the ops field in
the regulator_desc struct, which is a const pointer. Make them const to
allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-9-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of tps65912_ops_dcdc and tps65912_ops_ldo is to assign
their address to the ops field in the regulator_desc struct, which is a
const pointer. Make them const to allow the compiler to put them in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-8-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of these are to assign their address to the ops field in
the regulator_desc struct, which is a const pointer. Make them const to
allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-7-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usages of these are to assign their address to the ops field in
the regulator_desc struct, which is a const pointer. Make them const to
allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-6-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of reg_ops and switch_ops is to assign their addresses to
the ops field in the regulator_desc struct, which is a const pointer.
Make them const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-5-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of tps62360_dcdc_ops is to assign its address to the ops
field in the regulator_desc struct, which is a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-4-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of tps6105x_regulator_ops is to assign its address to the
ops field in the regulator_desc struct, which is a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-3-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of tps51632_dcdc_ops is to assign its address to the ops
field in the regulator_desc struct, which is a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200829221104.20870-2-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent commit 7d8196641e ("regulator: Remove pointer table
overallocation") changed the size of coupled_rdevs and now KASAN is able
to detect slab-out-of-bounds problem in regulator_unlock_recursive(),
which is a legit problem caused by a typo in the code. The recursive
unlock function uses n_coupled value of a parent regulator for unlocking
supply regulator, while supply's n_coupled should be used. In practice
problem may only affect platforms that use coupled regulators.
Cc: stable@vger.kernel.org # 5.0+
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200831204335.19489-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As Rob suggested, use the "mps,switch-frequency-hz" instead of the
"mps,switch-frequency" for switch frequency. Fortunately, the switch
frequency support isn't released, so we can modify it now without
any concern.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200824102402.4047fa5f@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
The following build warning is seen after commit 8bdaa43808 ("regulator:
dbx500: no need to check return value of debugfs_create functions"):
drivers/regulator/dbx500-prcmu.c:144:1: warning: label 'exit_no_debugfs' defined but not used [-Wunused-label]
Remove the unused label and its associated error message.
Fixes: 8bdaa43808 ("regulator: dbx500: no need to check return value of debugfs_create functions")
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200821144823.13404-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/tps65023-regulator.c:319:34: warning: ‘tps65023_of_match’ defined but not used [-Wunused-const-variable=]
319 | static const struct of_device_id tps65023_of_match[] = {
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821112009.58ee8511@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/qcom-rpmh-regulator.c:970:34: warning: ‘rpmh_regulator_match_table’ defined but not used [-Wunused-const-variable=]
970 | static const struct of_device_id rpmh_regulator_match_table[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111913.1096f7cc@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/sy8106a-regulator.c:126:34: warning: ‘sy8106a_i2c_of_match’ defined but not used [-Wunused-const-variable=]
126 | static const struct of_device_id sy8106a_i2c_of_match[] = {
| ^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111820.5c6ddb04@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/stm32-pwr.c:169:34: warning: ‘stm32_pwr_of_match’ defined but not used [-Wunused-const-variable=]
169 | static const struct of_device_id stm32_pwr_of_match[] = {
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111726.38e0e746@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/pwm-regulator.c:393:34: warning: ‘pwm_of_match’ defined but not used [-Wunused-const-variable=]
393 | static const struct of_device_id pwm_of_match[] = {
| ^~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111658.59a7218b@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/max77826-regulator.c:277:34: warning: ‘max77826_of_match’ defined but not used [-Wunused-const-variable=]
277 | static const struct of_device_id max77826_of_match[] = {
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111631.4e799c86@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/max1586.c:204:34: warning: ‘max1586_of_match’ defined but not used [-Wunused-const-variable=]
204 | static const struct of_device_id max1586_of_match[] = {
| ^~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111601.26243417@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/ltc3676.c:371:34: warning: ‘ltc3676_of_match’ defined but not used [-Wunused-const-variable=]
371 | static const struct of_device_id ltc3676_of_match[] = {
| ^~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111517.59d7b8c8@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/ltc3589.c:460:34: warning: ‘ltc3589_of_match’ defined but not used [-Wunused-const-variable=]
460 | static const struct of_device_id ltc3589_of_match[] = {
| ^~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111449.7cf580f2@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warnings when CONFIG_OF=n:
drivers/regulator/fixed.c:48:36: warning: ‘fixed_clkenable_data’ defined but not used [-Wunused-const-variable=]
48 | static const struct fixed_dev_type fixed_clkenable_data = {
| ^~~~~~~~~~~~~~~~~~~~
drivers/regulator/fixed.c:44:36: warning: ‘fixed_voltage_data’ defined but not used [-Wunused-const-variable=]
44 | static const struct fixed_dev_type fixed_voltage_data = {
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111403.3e8b58a3@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/fan53555.c:439:34: warning: ‘fan53555_dt_ids’ defined but not used [-Wunused-const-variable=]
439 | static const struct of_device_id fan53555_dt_ids[] = {
| ^~~~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111324.430fe1da@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/da9210-regulator.c:128:34: warning: ‘da9210_dt_ids’ defined but not used [-Wunused-const-variable=]
128 | static const struct of_device_id da9210_dt_ids[] = {
| ^~~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200821111235.14473a88@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below warning when CONFIG_OF=n:
drivers/regulator/88pg86x.c:87:34: warning: ‘pg86x_dt_ids’ defined but not used [-Wunused-const-variable=]
87 | static const struct of_device_id pg86x_dt_ids [] = {
| ^~~~~~~~~~~~
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200821111210.0a0bed94@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20200818133701.462958-1-gregkh@linuxfoundation.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows the regulator to be found by devm_regulator_get().
Fixes: 4fe66d5a62 ("regulator: Add support for QCOM PMIC VBUS booster")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200818162508.5246-1-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang <Jisheng.Zhang@synaptics.com>:
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This is to improve the mp886x regulator driver support.
patch1 implments .set_ramp_delay
patch2 and patch3 support the switch freq setting
patch4 converts dt binding to json-schema
Since v2:
- put any schema conversions at the end of the series as Mark
suggested.
Jisheng Zhang (4):
regulator: mp886x: implement set_ramp_delay
dt-bindings: regulator: mp886x: support mps,switch-frequency
regulator: mp886x: support setting switch freq
dt-bindings: regulator: Convert mp886x to json-schema
.../devicetree/bindings/regulator/mp886x.txt | 27 -----
.../bindings/regulator/mps,mp886x.yaml | 58 ++++++++++
drivers/regulator/mp886x.c | 109 +++++++++++++++++-
3 files changed, 164 insertions(+), 30 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/regulator/mp886x.txt
create mode 100644 Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
--
2.28.0.rc1
For systems that have eg. eMMC storage using voltage regulator, memory
reclaim path might call back into regulator subsystem. This means we
have to make sure no allocations happen with a regulator or regulator
list locked.
After this series I see no more lockdep complaints on my test system,
but please review and test further.
First four patches move allocations out of locked regions, next three
came as a drive-by cleanups.
---
v2: fix bug in patch #4 spotted by kernel test robot
reworded commit #7 description
Michał Mirosław (7):
regulator: push allocation in regulator_init_coupling() outside of
lock
regulator: push allocation in regulator_ena_gpio_request() out of lock
regulator: push allocations in create_regulator() outside of lock
regulator: push allocation in set_consumer_device_supply() out of lock
regulator: plug of_node leak in regulator_register()'s error path
regulator: cleanup regulator_ena_gpio_free()
regulator: remove superfluous lock in regulator_resolve_coupling()
drivers/regulator/core.c | 164 +++++++++++++++++++++------------------
1 file changed, 87 insertions(+), 77 deletions(-)
--
2.20.1
By checking data->pin_ctrl_enable / data->pin_ctrl_hpm flags first, then
use switch-case to improve readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200801054820.134859-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This regulator/backlight driver handles the ATTINY88 present on the
RPi 7" touchscreen panel and exposes the power/backlight interfaces.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: dri-devel@lists.freedesktop.org
Link: https://lore.kernel.org/r/20200809105938.6388-2-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
I see it takes about 5us per regulator to grab the lock, check that this
regulator isn't going to do anything for suspend, and then release the
lock. When that is combined with PMICs that have dozens of regulators we
get into a state where we spend a few miliseconds doing a bunch of
locking operations synchronously to figure out that there's nothing to
do. Let's reorganize the code here a bit so that we don't grab the lock
until we're actually going to do something so that suspend is a little
faster.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200804070837.1084024-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing W=1 build warning when no support for device tree is there.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200810095753.59ce9f75@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regmap_cache to reduce wakeups events of interrupt if regulator is
accessed frequently. This results in saving more power.
Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200812133101.2513317-1-hsinyi@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds support for the RT4801 DSV. It has two regulators (DSVP/DSVN) with
an I2C interface. DSVP/DSVN can provide the display panel module for the
positive/negative voltage range from (+/-)4V to (+/-)6V.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1597461262-25878-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code modifies rdev, but locks c_rdev instead. Remove the lock
as this is held together by regulator_list_mutex taken in the caller.
Fixes: f9503385b1 ("regulator: core: Mutually resolve regulators coupling")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/25eb81cefb37a646f3e44eaaf1d8ae8881cfde52.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Since only regulator_ena_gpio_request() allocates rdev->ena_pin, and it
guarantees that same gpiod gets same pin structure, it is enough to
compare just the pointers. Also we know there can be only one matching
entry on the list. Rework the code take advantage of the facts.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/3ff002c7aa3bd774491af4291a9df23541fcf892.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
By calling device_initialize() earlier and noting that kfree(NULL) is
ok, we can save a bit of code in error handling and plug of_node leak.
Fixed commit already did part of the work.
Fixes: 9177514ce3 ("regulator: fix memory leak on error path of regulator_register()")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/f5035b1b4d40745e66bacd571bbbb5e4644d21a1.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all allocations outside of the regulator_lock()ed section.
======================================================
WARNING: possible circular locking dependency detected
5.7.13+ #535 Not tainted
------------------------------------------------------
f2fs_discard-179:7/702 is trying to acquire lock:
c0e5d920 (regulator_list_mutex){+.+.}-{3:3}, at: regulator_lock_dependent+0x54/0x2c0
but task is already holding lock:
cb95b080 (&dcc->cmd_lock){+.+.}-{3:3}, at: __issue_discard_cmd+0xec/0x5f8
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
[...]
-> #3 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire.part.11+0x40/0x50
fs_reclaim_acquire+0x24/0x28
__kmalloc_track_caller+0x54/0x218
kstrdup+0x40/0x5c
create_regulator+0xf4/0x368
regulator_resolve_supply+0x1a0/0x200
regulator_register+0x9c8/0x163c
[...]
other info that might help us debug this:
Chain exists of:
regulator_list_mutex --> &sit_i->sentry_lock --> &dcc->cmd_lock
[...]
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/6eebc99b2474f4ffaa0405b15178ece0e7e4f608.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Move another allocation out of regulator_list_mutex-protected region, as
reclaim might want to take the same lock.
WARNING: possible circular locking dependency detected
5.7.13+ #534 Not tainted
------------------------------------------------------
kswapd0/383 is trying to acquire lock:
c0e5d920 (regulator_list_mutex){+.+.}-{3:3}, at: regulator_lock_dependent+0x54/0x2c0
but task is already holding lock:
c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire.part.11+0x40/0x50
fs_reclaim_acquire+0x24/0x28
kmem_cache_alloc_trace+0x40/0x1e8
regulator_register+0x384/0x1630
devm_regulator_register+0x50/0x84
reg_fixed_voltage_probe+0x248/0x35c
[...]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
lock(regulator_list_mutex);
lock(fs_reclaim);
lock(regulator_list_mutex);
*** DEADLOCK ***
[...]
2 locks held by kswapd0/383:
#0: c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
#1: cb70e5e0 (hctx->srcu){....}-{0:0}, at: hctx_lock+0x60/0xb8
[...]
Fixes: 541d052d72 ("regulator: core: Only support passing enable GPIO descriptors")
[this commit only changes context]
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
[this is when the regulator_list_mutex was introduced in reclaim locking path]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/41fe6a9670335721b48e8f5195038c3d67a3bf92.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Allocating memory with regulator_list_mutex held makes lockdep unhappy
when memory pressure makes the system do fs_reclaim on eg. eMMC using
a regulator. Push the lock inside regulator_init_coupling() after the
allocation.
======================================================
WARNING: possible circular locking dependency detected
5.7.13+ #533 Not tainted
------------------------------------------------------
kswapd0/383 is trying to acquire lock:
cca78ca4 (&sbi->write_io[i][j].io_rwsem){++++}-{3:3}, at: __submit_merged_write_cond+0x104/0x154
but task is already holding lock:
c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire.part.11+0x40/0x50
fs_reclaim_acquire+0x24/0x28
__kmalloc+0x54/0x218
regulator_register+0x860/0x1584
dummy_regulator_probe+0x60/0xa8
[...]
other info that might help us debug this:
Chain exists of:
&sbi->write_io[i][j].io_rwsem --> regulator_list_mutex --> fs_reclaim
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
lock(regulator_list_mutex);
lock(fs_reclaim);
lock(&sbi->write_io[i][j].io_rwsem);
*** DEADLOCK ***
1 lock held by kswapd0/383:
#0: c0e38518 (fs_reclaim){+.+.}-{0:0}, at: __fs_reclaim_acquire+0x0/0x50
[...]
Fixes: d8ca7d184b ("regulator: core: Introduce API for regulators coupling customization")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1a889cf7f61c6429c9e6b34ddcdde99be77a26b6.1597195321.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Both MP8867 and MP8869 support different switch frequency.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200729131023.77cc1dd2@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement the .set_ramp_delay for MP8867 and MP8869. MP8867 and MP8869
could share the implementation, the only difference is the slew_rates
array.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200729130913.3ac38b32@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
The desc->name field is allocated with devm_kstrdup, but is also kfreed
on the error path, causing it to be double freed. Remove the kfree on
the error path.
Fixes: 8d9f8d57e0 ("regulator: Add driver for cros-ec-regulator")
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200728091909.2009771-1-pihsun@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The change corrects registration and deregistration on error path
of a regulator, the problem was manifested by a reported memory
leak on deferred probe:
as3722-regulator as3722-regulator: regulator 13 register failed -517
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xecc43740 (size 64):
comm "swapper/0", pid 1, jiffies 4294937640 (age 712.880s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 2e 32 34 00 5a 5a 5a regulator.24.ZZZ
5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
backtrace:
[<0c4c3d1c>] __kmalloc_track_caller+0x15c/0x2c0
[<40c0ad48>] kvasprintf+0x64/0xd4
[<109abd29>] kvasprintf_const+0x70/0x84
[<c4215946>] kobject_set_name_vargs+0x34/0xa8
[<62282ea2>] dev_set_name+0x40/0x64
[<a39b6757>] regulator_register+0x3a4/0x1344
[<16a9543f>] devm_regulator_register+0x4c/0x84
[<51a4c6a1>] as3722_regulator_probe+0x294/0x754
...
The memory leak problem was introduced as a side ef another fix in
regulator_register() error path, I believe that the proper fix is
to decouple device_register() function into its two compounds and
initialize a struct device before assigning any values to its fields
and then using it before actual registration of a device happens.
This lets to call put_device() safely after initialization, and, since
now a release callback is called, kfree(rdev->constraints) shall be
removed to exclude a double free condition.
Fixes: a3cde9534e ("regulator: core: fix regulator_register() error paths to properly release rdev")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Wen Yang <wenyang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20200724005013.23278-1-vz@mleia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719200623.61524-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Consider the following example:
- regulator-X is provided by device-X.
- regulator-X is a supplier to device-A, device-B and device-C.
- device-A is off/inactive from boot.
- device-B and device-C are left on/active by the bootloader
- regulator-X is left on boot by the bootloader at 2000 mV to supply
device-B and device-C.
Example boot sequence 1:
1. device-X is probed successfully.
2. device-A is probed by driver-A
a. driver-A gets regulator-X
b. driver-A votes on regulator-X
c. driver-A initializes device-A
d. driver-A votes off regulator-X
e. regulator-X is turned off.
3. System crashes or device-B and device-C become unreliable because
regulator-X was turned off without following the proper quiescing
steps for device-B and device-C.
Example boot sequence 2:
1. device-X is probed successfully.
2. device-B is probed by driver-B
a. driver-B gets regulator-X
b. driver-B votes on regulator-X
c. driver-B lowers device-B performance point.
d. driver-B lowers voltage vote to 1000 mV.
e. regulator-X voltage is lowered to 1000 mV.
3. System crashes or device-C becomes unreliable because regulator-X
voltage was lowered to 1000 mV when device-C still needed it at 2000 mV
This patch series makes sure these examples are handled correctly and
system crash or device instability is avoided and the system remains
usable.
More details provided in the commit texts.
v2->v3:
Patch 2/4 - No functional change. Simple refactor.
Patch 3/4
- Was Patch 2/2 in v2.
- Rewrote commit text to hopefully address all previous points.
- Renamed variable/functions. Hope it's clearer.
- Added more comments.
- Added logging
- Fixed timeout functionality.
- Handle exclusive consumers properly
- Handle coupled regulators properly
Patch 4/4 - Prevents voltage from going too low during boot.
v1->v2:
Patch 1/2
- New patch
Patch 2/2
- This was the only patch in v1
- Made the late_initcall_sync timeout a commandline param
- If timeout is set, we also give up waiting for all consumers after
the timeout expires.
- Made every regulator driver add sync_state() support
Saravana Kannan (4):
driver core: Add dev_set_drv_sync_state()
regulator: core: Add destroy_regulator()
regulator: core: Add basic enable/disable support for sync_state()
callbacks
regulator: core: Add voltage support for sync_state() callbacks
drivers/regulator/core.c | 200 ++++++++++++++++++++++++++++---
include/linux/device.h | 12 ++
include/linux/regulator/driver.h | 2 +
3 files changed, 198 insertions(+), 16 deletions(-)
--
2.28.0.rc0.105.gf9edc3c819-goog
When requesting the enable GPIO, the driver should do so with the
correct output level matching some expected state. This is especially
important if the regulator is a critical one, such as a supply for
the boot CPU. This is currently done by checking for the enable-at-boot
property, but this is not documented in the device tree binding, nor
does it match the common regulator properties.
Honor the common regulator-boot-on property by checking the boot_on
constraint setting within the DT probe path. This is the same as what
is done in the fixed regulator driver.
Also add a comment stating that the enable-at-boot property should not
be used.
Fixes: 006694d099 ("regulator: gpio-regulator: Allow use of GPIO controlled regulators though DT")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200720132809.26908-1-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Part of the regulator_get() code is already factored out into
create_regulator(). This patch factors out some of the regulator_put()
code into destroy_regulator() so that create_regulator() has a
corresponding unwind function. Subsequent patches will use this
function.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20200716042053.1927676-3-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm platforms have LAB(LCD AMOLED Boost)/IBB(Inverting Buck Boost)
regulators, labibb for short, which are used as power supply for
LCD Mode displays.
This patch adds labibb regulator driver for pmi8998 PMIC, found on
SDM845 platforms.
[sumits: reworked the driver design as per upstream review]
Signed-off-by: Nisha Kumari <nishakumari@codeaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://lore.kernel.org/r/20200622124110.20971-5-sumit.semwal@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators might need to verify that they have indeed been enabled
after the enable() call is made and enable_time delay has passed.
This is implemented by repeatedly checking is_enabled() upto
poll_enabled_time, waiting for the already calculated enable delay in
each iteration.
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://lore.kernel.org/r/20200622124110.20971-2-sumit.semwal@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is never modified, so make it const to allow the compiler to put it
in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Pi-Hsun Shih <pihsun@chromium.org>
Link: https://lore.kernel.org/r/20200711114409.9911-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Line up descriptions, start description with a lower-case character and
omit old definitions such as quoting the old argument "consumer".
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200708124832.3441649-4-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Kerneldoc validation gets confused if syntax isn't "@.*: ".
Adding the missing colons squashes the following W=1 warnings:
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Rajendra Nayak <rnayak@ti.com>
Link: https://lore.kernel.org/r/20200708124832.3441649-3-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide descriptions for some missing function args and
rename others to match the names used.
Fixes the following W=1 warning(s):
drivers/regulator/devres.c:187: warning: Function parameter or member 'dev' not described in 'devm_regulator_register'
drivers/regulator/devres.c:226: warning: Function parameter or member 'dev' not described in 'devm_regulator_unregister'
drivers/regulator/devres.c:226: warning: Function parameter or member 'rdev' not described in 'devm_regulator_unregister'
drivers/regulator/devres.c:226: warning: Excess function parameter 'regulator' description in 'devm_regulator_unregister'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200708124832.3441649-2-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for COMPILE_TEST while fixing a warning when
no support for device tree is there.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/1c437154873ace65ff738a0ebca511308f1cecc1.camel@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for ON Semiconductor FAN53880 regulator.
The FAN53880 is an I2C porgrammable power management IC (PMIC)
that contains a BUCK (step-down converter), four LDOs (low dropouts)
and one BOOST (step-up converter). It is designed for mobile power
applications.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/20200702210846.31659-2-chf.fritz@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds support for being able to change regulator modes for
the mt6397 regulator. This is needed to allow the voltage scaling
support in the MT8173 SoC to be used on the elm (Acer Chromebook R13)
and hana (several Lenovo Chromebooks) devices.
Without a of_map_mode implementation, the regulator-allowed-modes
devicetree field is skipped, and attempting to change the regulator mode
results in an error:
[ 1.439165] vpca15: mode operation not allowed
Changes in v2:
- Introduce constants in dt-bindings
- Improve conditional readability
Anand K Mistry (4):
regulator: mt6397: Move buck modes into header file
dt-bindings: regulator: mt6397: Document valid modes
regulator: mt6397: Implement of_map_mode
arm64: dts: mediatek: Update allowed mt6397 regulator modes for elm
boards
.../bindings/regulator/mt6397-regulator.txt | 3 +++
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 4 +++-
drivers/regulator/mt6397-regulator.c | 17 ++++++++++++++---
.../regulator/mediatek,mt6397-regulator.h | 15 +++++++++++++++
4 files changed, 35 insertions(+), 4 deletions(-)
create mode 100644 include/dt-bindings/regulator/mediatek,mt6397-regulator.h
--
2.27.0.212.ge8ba1cc988-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
This patchset adds support for being able to change regulator modes for
the da9211 regulator. This is needed to allow the voltage scaling
support in the MT8173 SoC to be used in the elm (Acer Chromebook R13)
and hana (several Lenovo Chromebooks) devices.
Anand K Mistry (4):
regulator: da9211: Move buck modes into header file
dt-bindings: regulator: da9211: Document allowed modes
regulator: da9211: Implement of_map_mode
arm64: dts: mediatek: Update allowed regulator modes for elm boards
.../devicetree/bindings/regulator/da9211.txt | 4 +++
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 4 ++-
drivers/regulator/da9211-regulator.c | 30 +++++++++++++++----
.../regulator/dlg,da9211-regulator.h | 16 ++++++++++
4 files changed, 47 insertions(+), 7 deletions(-)
create mode 100644 include/dt-bindings/regulator/dlg,da9211-regulator.h
--
2.27.0.212.ge8ba1cc988-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The SY8827N from Silergy Corp is a single output DC/DC converter. The
voltage can be controlled via I2C.
Jisheng Zhang (2):
dt-bindings: regulator: add document bindings for sy8827n
regulator: add support for SY8827N regulator
.../bindings/regulator/silergy,sy8827n.yaml | 45 +++++
drivers/regulator/Kconfig | 7 +
drivers/regulator/Makefile | 1 +
drivers/regulator/sy8827n.c | 185 ++++++++++++++++++
4 files changed, 238 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/silergy,sy8827n.yaml
create mode 100644 drivers/regulator/sy8827n.c
--
2.27.0
Use the new .probe_new for mp886x. It does not use the const
struct i2c_device_id * argument, so convert it to utilise the
simplified i2c driver registration.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200702100200.1a4c65d1@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
The null pointer check on regmap that checks for a dev_get_regmap failure
is currently returning -ENOENT if the regmap succeeded. Fix this by adding
in the missing ! operator.
Fixes: 4fe66d5a62 ("regulator: Add support for QCOM PMIC VBUS booster")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference after null check")
Link: https://lore.kernel.org/r/20200702115659.38208-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SY8827N from Silergy Corp is a single output DC/DC converter. The
voltage can be controlled via I2C.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200702171438.20edc523@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Changes in v4:
- Modified qcom,pmic-typec binding to include the SS mux and the DRD remote
endpoint nodes underneath port@1, which is assigned to the SSUSB path
according to usb-connector
- Added usb-connector reference to the typec dt-binding
- Added tags to the usb type c and vbus nodes
- Removed "qcom" tags from type c and vbus nodes
- Modified Kconfig module name, and removed module alias from the typec driver
Changes in v3:
- Fix driver reference to match driver name in Kconfig for
qcom_usb_vbus-regulator.c
- Utilize regulator bitmap helpers for enable, disable and is enabled calls in
qcom_usb_vbus-regulator.c
- Use of_get_regulator_init_data() to initialize regulator init data, and to
set constraints in qcom_usb_vbus-regulator.c
- Remove the need for a local device structure in the vbus regulator driver
Changes in v2:
- Use devm_kzalloc() in qcom_pmic_typec_probe()
- Add checks to make sure return value of typec_find_port_power_role() is
valid
- Added a VBUS output regulator driver, which will be used by the PMIC USB
type c driver to enable/disable the source
- Added logic to control vbus source from the PMIC type c driver when
UFP/DFP is detected
- Added dt-binding for this new regulator driver
- Fixed Kconfig typec notation to match others
- Leave type C block disabled until enabled by a platform DTS
Add the required drivers for implementing type C orientation and role
detection using the Qualcomm PMIC. Currently, PMICs such as the PM8150B
have an integrated type C block, which can be utilized for this. This
series adds the dt-binding, PMIC type C driver, and DTS nodes.
The PMIC type C driver will register itself as a type C port w/ a
registered type C switch for orientation, and will fetch a USB role switch
handle for the role notifications. It will also have the ability to enable
the VBUS output to any connected devices based on if the device is behaving
as a UFP or DFP.
Wesley Cheng (6):
usb: typec: Add QCOM PMIC typec detection driver
dt-bindings: usb: Add Qualcomm PMIC type C controller dt-binding
arm64: boot: dts: qcom: pm8150b: Add node for USB type C block
regulator: Add support for QCOM PMIC VBUS booster
dt-bindings: regulator: Add dt-binding for QCOM PMIC VBUS output
regulator
arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster
.../regulator/qcom,usb-vbus-regulator.yaml | 41 +++
.../bindings/usb/qcom,pmic-typec.yaml | 113 +++++++
arch/arm64/boot/dts/qcom/pm8150b.dtsi | 13 +
arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 4 +
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/qcom_usb_vbus-regulator.c | 97 ++++++
drivers/usb/typec/Kconfig | 12 +
drivers/usb/typec/Makefile | 1 +
drivers/usb/typec/qcom-pmic-typec.c | 275 ++++++++++++++++++
10 files changed, 567 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml
create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
create mode 100644 drivers/regulator/qcom_usb_vbus-regulator.c
create mode 100644 drivers/usb/typec/qcom-pmic-typec.c
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
IPQ6018 SoC uses the PMIC MP5496. SMPA2 and LDOA2 regulator of MP5496
controls the APSS and SDCC voltage scaling respectively. Add support
for the same.
changes since V1:
- Moved YAML conversion to the last as per Mark's comments
Kathiravan T (6):
dt-bindings: soc: qcom: Add IPQ6018 compatible
soc: qcom: smd-rpm: Add IPQ6018 compatible
dt-bindings: regulator: add MP5496 regulator compatible
regulator: qcom_smd: Add MP5496 regulators
dt-bindings: soc: qcom: convert the SMD-RPM document to YAML schema
dt-bindings: regulator: convert QCOM SMD-RPM regulator document to
YAML schema
.../bindings/regulator/qcom,smd-rpm-regulator.txt | 320 ---------------------
.../bindings/regulator/qcom,smd-rpm-regulator.yaml | 106 +++++++
.../devicetree/bindings/soc/qcom/qcom,smd-rpm.txt | 62 ----
.../devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml | 92 ++++++
drivers/regulator/qcom_smd-regulator.c | 34 +++
drivers/soc/qcom/smd-rpm.c | 1 +
6 files changed, 233 insertions(+), 382 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt
create mode 100644 Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml
delete mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
This driver enables outputs by setting bit EN_BUCKn in the BUCKn_CTRL1
register. However, if bit EN_PIN_CTRLn in the same register is set, the
output is actually enabled only if EN_BUCKn is set AND an enable pin is
active. Since the driver does not touch EN_PIN_CTRLn, the choice is left to
the hardware, which in turn gets this bit from OTP memory, and in absence
of OTP data it uses a default value that is documented in the datasheet for
LP8752x, but not for LP8756x.
Thus the driver doesn't really "know" whether it is actually enabling the
output or not.
In order to make sure activation is always driver-controlled, just clear
the EN_PIN_CTRLn bit. Now all activation solely depend on the EN_BUCKn bit.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20200622204329.11147-2-luca@lucaceresoli.net
Signed-off-by: Mark Brown <broonie@kernel.org>
IPQ6018 SoC uses the PMIC MP5496. SMPA2 and LDOA2 regulator controls the
APSS and SDCC voltage scaling respectively. Add support for the same.
Signed-off-by: Kathiravan T <kathirav@codeaurora.org>
Link: https://lore.kernel.org/r/1592889472-6843-5-git-send-email-kathirav@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
These are never modified, so make them const to allow the compiler to
put them in read-only memory.
Before:
text data bss dec hex filename
20362 2592 152 23106 5a42 drivers/regulator/qcom_spmi-regulator.o
After:
text data bss dec hex filename
21814 1140 152 23106 5a42 drivers/regulator/qcom_spmi-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200629194632.8147-3-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These are never modified, so make them const to allow the compiler to
put them in read-only memory.
Before:
text data bss dec hex filename
17485 500 8 17993 4649 drivers/regulator/qcom_rpm-regulator.o
After:
text data bss dec hex filename
17881 104 8 17993 4649 drivers/regulator/qcom_rpm-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200629194632.8147-2-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Qualcomm PMICs have the capability to source the VBUS output to
connected peripherals. This driver will register a regulator to the
regulator list to enable or disable this source by an external driver.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20200626185516.18018-5-wcheng@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This was an upstreaming error. Remove it as it's not to be used.
Fixes the following W=1 kernel build warning:
drivers/regulator/qcom_smd-regulator.c:477:36: warning: ‘pmi8994_boost’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-10-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
W=1 kernel builds report a lack of descriptions for various
function arguments. In reality they are documented, but the
formatting was not as expected '@.*:'. Instead, some weird
arg identifiers were used.
This change fixes the following warnings:
drivers/regulator/wm8400-regulator.c:243: warning: Function parameter or member 'dev' not described in 'wm8400_register_regulator'
drivers/regulator/wm8400-regulator.c:243: warning: Function parameter or member 'reg' not described in 'wm8400_register_regulator'
drivers/regulator/wm8400-regulator.c:243: warning: Function parameter or member 'initdata' not described in 'wm8400_register_regulator'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Link: https://lore.kernel.org/r/20200626065738.93412-9-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
'rid' is declared as unsigned int, so there is little point checking for <0.
Removing these checks fixes the following W=1 warnings:
drivers/regulator/tps65218-regulator.c: In function ‘tps65218_pmic_set_suspend_enable’:
drivers/regulator/tps65218-regulator.c:131:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
131 | if (rid < TPS65218_DCDC_1 || rid > TPS65218_LDO_1)
| ^
drivers/regulator/tps65218-regulator.c: In function ‘tps65218_pmic_set_suspend_disable’:
drivers/regulator/tps65218-regulator.c:144:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
144 | if (rid < TPS65218_DCDC_1 || rid > TPS65218_LDO_1)
| ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-8-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Until now the aforementioned return value has been ignored.
Previous and current calls to tps65217_reg_read() return
instantly when the value is not 0, so let's do that.
Fixes the following W=1 warning:
drivers/regulator/tps65217-regulator.c: In function ‘tps65217_regulator_probe’:
drivers/regulator/tps65217-regulator.c:227:9: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
227 | int i, ret;
| ^~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Russ Dill <Russ.Dill@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-7-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
'rid' is declared as unsigned int, so there is little point checking for <0.
Removing these checks fixes the following W=1 warnings:
drivers/regulator/tps65217-regulator.c: In function ‘tps65217_pmic_set_suspend_enable’:
drivers/regulator/tps65217-regulator.c:127:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
127 | if (rid < TPS65217_DCDC_1 || rid > TPS65217_LDO_4)
| ^
drivers/regulator/tps65217-regulator.c: In function ‘tps65217_pmic_set_suspend_disable’:
drivers/regulator/tps65217-regulator.c:140:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
140 | if (rid < TPS65217_DCDC_1 || rid > TPS65217_LDO_4)
| ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Russ Dill <Russ.Dill@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-6-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In kerneldoc format, data structures have to start with 'struct'
else the kerneldoc tooling/parsers/validators get confused.
Fixes the following W=1 kernel build warning:
drivers/regulator/stpmic1_regulator.c:25: warning: cannot understand function prototype: 'struct stpmic1_regulator_cfg '
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Pascal Paillet <p.paillet@st.com>
Link: https://lore.kernel.org/r/20200626065738.93412-5-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This particular comment doesn't have anything to do with documenting
functions or data structures. Instead it is used as a section header.
Fixes W=1 warning:
drivers/regulator/pwm-regulator.c:55: warning: Function parameter or member 'rdev' not described in 'pwm_regulator_init_state'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200626065738.93412-4-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
W=1 kernel builds report a lack of descriptions for various
enum properties and function arguments. In reality they are
documented, but the formatting was not as expected '@.*:'.
Instead, some weird arg identifiers were used or none at all.
This change fixes the following warnings:
drivers/regulator/qcom-rpmh-regulator.c:33: warning: Enum value 'VRM' not described in enum 'rpmh_regulator_type'
drivers/regulator/qcom-rpmh-regulator.c:33: warning: Enum value 'XOB' not described in enum 'rpmh_regulator_type'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'vreg' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'dev' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'node' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'pmic_id' not described in 'rpmh_regulator_init_vreg'
drivers/regulator/qcom-rpmh-regulator.c:416: warning: Function parameter or member 'pmic_rpmh_data' not described in 'rpmh_regulator_init_vreg'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20200626065738.93412-3-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
max8998_get_current_limit() is only used via the .get_current_limit,
so it doesn't need to be publicly supported, or to have its own
external prototype. Instead, we'll make it static.
Fixes the following W=1 warning:
drivers/regulator/max8998.c:418:5: warning: no previous prototype for ‘max8998_get_current_limit’ [-Wmissing-prototypes]
418 | int max8998_get_current_limit(struct regulator_dev *rdev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200626065738.93412-2-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Nothing about this comment identifies it as a kerneldoc header.
It's missing all of it's function argument descriptions and the
correct function header.
Fixes the following W=1 warning(s):
drivers/regulator/max14577-regulator.c:166: warning: Function parameter or member 'max14577' not described in 'max14577_get_regma
drivers/regulator/max14577-regulator.c:166: warning: Function parameter or member 'reg_id' not described in 'max14577_get_regmap'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200625163614.4001403-11-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Nothing about this comment identifies it as a kerneldoc header.
They're missing all of their struct's property descriptions and
the correct 'struct *' header.
Fixes the following W=1 warning(s):
drivers/regulator/cpcap-regulator.c:99: warning: cannot understand function prototype: 'struct cpcap_regulator '
drivers/regulator/cpcap-regulator.c:337: warning: cannot understand function prototype: 'const struct cpcap_regulator omap4_regulators[] = '
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200625163614.4001403-9-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It's okay to not check the return value that you're not conserned
about, however it is not okay to assign a variable and not check or
use the result.
Fixes W=1 warnings(s):
drivers/regulator/cpcap-regulator.c:172:13: warning: variable ‘ignore’ set but not used [-Wunused-but-set-variable]
172 | int error, ignore;
| ^~~~~~
drivers/regulator/cpcap-regulator.c: In function ‘cpcap_regulator_disable’:
drivers/regulator/cpcap-regulator.c:196:13: warning: variable ‘ignore’ set but not used [-Wunused-but-set-variable]
196 | int error, ignore;
| ^~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200625163614.4001403-8-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Kerneldoc expects function arguments to be in the format '@.*:'. If
this format is not followed the kerneldoc tooling/parsers/validators
get confused.
Fixes the following W=1 warning(s):
drivers/regulator/wm8350-regulator.c🔢 warning: Function parameter or member 'wm8350' not described in 'wm8350_register_led'
drivers/regulator/wm8350-regulator.c🔢 warning: Function parameter or member 'lednum' not described in 'wm8350_register_led'
drivers/regulator/wm8350-regulator.c🔢 warning: Function parameter or member 'dcdc' not described in 'wm8350_register_led'
drivers/regulator/wm8350-regulator.c🔢 warning: Function parameter or member 'isink' not described in 'wm8350_register_led'
drivers/regulator/wm8350-regulator.c🔢 warning: Function parameter or member 'pdata' not described in 'wm8350_register_led'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200625163614.4001403-7-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Used primarily for the AB8540 which lost support in early 2018.
It is now deemed safe to remove this legacy data structure.
Also fixes W=1 issue:
drivers/regulator/ab8500.c:88: warning: Function parameter or member 'expand_register' not described in 'ab8500_regulator_info'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200625163614.4001403-6-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There isn't any code present within the current kernel to
override this 'weak' function. Besides returning '0', which
is never checked anyway, the whole function appears to be
superfluous.
Consequently fixes W=1 warning:
drivers/regulator/dbx500-prcmu.c:113:27: warning: no previous prototype for ‘dbx500_regulator_testcase’ [-Wmissing-prototypes]
113 | int __attribute__((weak)) dbx500_regulator_testcase(
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200625163614.4001403-5-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This module shares the same name as its parent PMIC driver, which
confuses tools like kmod. Rename the regulator driver to avoid
such problems.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Link: https://lore.kernel.org/r/20200624171010.845271-1-seth.forshee@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These are not modified so make them const to allow the compiler to put
them in read-only memory.
Before:
text data bss dec hex filename
13114 8596 0 21710 54ce drivers/regulator/max8997-regulator.o
After:
text data bss dec hex filename
14038 7672 0 21710 54ce drivers/regulator/max8997-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200617223247.25566-6-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These are not modified so make them const to allow the compiler to put
them in read-only memory.
Before:
text data bss dec hex filename
2753 7328 0 10081 2761 drivers/regulator/max8907-regulator.o
After:
text data bss dec hex filename
9405 684 0 10089 2769 drivers/regulator/max8907-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200617223247.25566-5-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ltc3676_regulators is not modified and can be made const to allow the
compiler to put it in read-only memory.
Before:
text data bss dec hex filename
4361 2064 8 6433 1921 drivers/regulator/ltc3676.o
After:
text data bss dec hex filename
6121 304 8 6433 1921 drivers/regulator/ltc3676.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200617223247.25566-4-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cpcap_regulator_ops is not modified and can be made const to allow the
compiler to put it in read-only memory.
Before:
text data bss dec hex filename
14472 236 0 14708 3974 drivers/regulator/cpcap-regulator.o
After:
text data bss dec hex filename
14604 104 0 14708 3974 drivers/regulator/cpcap-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200617223247.25566-3-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
anatop_core_rops is not modified and can therefore be made const which
allows the compiler to put it in read-only memory.
Before:
text data bss dec hex filename
4502 412 0 4914 1332 drivers/regulator/anatop-regulator.o
After:
text data bss dec hex filename
4634 280 0 4914 1332 drivers/regulator/anatop-regulator.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200617223247.25566-2-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for controlling voltage regulator that is connected and
controlled by ChromeOS EC. Kernel controls these regulators through
newly added EC host commands.
Changes from v5:
* Move new host command to a separate patch.
* Use devm_regulator_register.
* Address review comments.
Changes from v4:
* Change compatible name from regulator-cros-ec to cros-ec-regulator.
Changes from v3:
* Fix dt bindings file name.
* Remove check around CONFIG_OF in driver.
* Add new host commands to cros_ec_trace.
* Address review comments.
Changes from v2:
* Add 'depends on OF' to Kconfig.
* Add Kconfig description about compiling as module.
Changes from v1:
* Change compatible string to google,regulator-cros-ec.
* Use reg property in device tree.
* Change license for dt binding according to checkpatch.pl.
* Address comments on code styles.
Pi-Hsun Shih (3):
dt-bindings: regulator: Add DT binding for cros-ec-regulator
platform/chrome: cros_ec: Add command for regulator control.
regulator: Add driver for cros-ec-regulator
.../regulator/google,cros-ec-regulator.yaml | 51 ++++
drivers/platform/chrome/cros_ec_trace.c | 5 +
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/cros-ec-regulator.c | 257 ++++++++++++++++++
.../linux/platform_data/cros_ec_commands.h | 82 ++++++
6 files changed, 406 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/google,cros-ec-regulator.yaml
create mode 100644 drivers/regulator/cros-ec-regulator.c
base-commit: b791d1bdf9
--
2.27.0.290.gba653c62da-goog
Add driver for cros-ec-regulator, representing a voltage regulator that
is connected and controlled by ChromeOS EC, and is controlled by kernel
with EC host commands.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200612040526.192878-4-pihsun@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
PFUZE100_SWB_REG is not proper for sw1a/sw2, because enable_mask/enable_reg
is not correct. On PFUZE3000, sw1a/sw2 should be the same as sw1a/sw2 on
pfuze100 except that voltages are not linear, so add new PFUZE3000_SW_REG
and pfuze3000_sw_regulator_ops which like the non-linear PFUZE100_SW_REG
and pfuze100_sw_regulator_ops.
Fixes: 1dced996ee ("regulator: pfuze100: update voltage setting for pfuze3000 sw1a")
Reported-by: Christophe Meynard <Christophe.Meynard@ign.fr>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592171648-8752-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pickable ranges mapping function never used range min selector. Thus
existing drivers broke when proper linear_ranges functionality was taken
in use. Fix this for now just by ignoring the minimum selector.
Fixes: 60ab7f4153 ("regulator: use linear_ranges helper")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200612090225.GA3243@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 99f75ce666 ("regulator: da9063: fix suspend") converted
the regulators to use a common (corrected) suspend bit setting but
one of regulators (LDO9) slipped through the crack.
This means that the original problem was not fixed for LDO9 and
also leads to a warning found by the test robot.
da9063-regulator.c:515:3: warning: initialized field overwritten
Fix this by converting that regulator too like the others.
Fixes: 99f75ce666 ("regulator: da9063: fix suspend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Link: https://lore.kernel.org/r/1591959073-16792-1-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new trace points for the start and end of enabling bypass on a
regulator, to allow monitoring of when regulators are moved into bypass
and how long that takes.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200529152216.9671-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi!
This patchset is another attempt to fix the regulator coupling on
Exynos5800/5422 SoCs. Here are links to the previous attempts:
https://lore.kernel.org/linux-samsung-soc/20191008101709.qVNy8eijBi0LynOteWFMnTg4GUwKG599n6OyYoX1Abs@z/https://lore.kernel.org/lkml/20191017102758.8104-1-m.szyprowski@samsung.com/https://lore.kernel.org/linux-pm/cover.1589528491.git.viresh.kumar@linaro.org/https://lore.kernel.org/linux-pm/20200528131130.17984-1-m.szyprowski@samsung.com/
The problem is with "vdd_int" regulator coupled with "vdd_arm" on Odroid
XU3/XU4 boards family. "vdd_arm" is handled by CPUfreq. "vdd_int" is
handled by devfreq. CPUfreq initialized quite early during boot and it
starts changing OPPs and "vdd_arm" value. Sometimes CPU activity during
boot goes down and some low-frequency OPPs are selected, what in turn
causes lowering "vdd_arm". This happens before devfreq applies its
requirements on "vdd_int". Regulator balancing code reduces "vdd_arm"
voltage value, what in turn causes lowering "vdd_int" value to the lowest
possible value. This is much below the operation point of the wcore bus,
which still runs at the highest frequency.
The issue was hard to notice because in the most cases the board managed
to boot properly, even when the regulator was set to lowest value allowed
by the regulator constraints. However, it caused some random issues,
which can be observed as "Unhandled prefetch abort" or low USB stability.
Adding more and more special cases to the generic code has been rejected,
so the only way to ensure the desired behavior on Exynos5800-based SoCs
is to make a custom regulator coupler driver.
Best regards,
Marek Szyprowski
Patch summary:
Marek Szyprowski (2):
regulator: extract voltage balancing code to separate function
soc: samsung: Add simple voltage coupler for Exynos5800
arch/arm/mach-exynos/Kconfig | 1 +
drivers/regulator/core.c | 49 ++++++++-------
drivers/soc/samsung/Kconfig | 3 +
drivers/soc/samsung/Makefile | 1 +
.../soc/samsung/exynos-regulator-coupler.c | 59 +++++++++++++++++++
include/linux/regulator/coupler.h | 8 +++
6 files changed, 101 insertions(+), 20 deletions(-)
create mode 100644 drivers/soc/samsung/exynos-regulator-coupler.c
--
2.17.1
base-commit: 8f3d9f3542
Move the coupled regulators voltage balancing code to the separate
function and allow to call it from the custom regulator couplers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200529124940.10675-2-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The max8998 has a current regulator for charging control. The
charger driver in drivers/power/supply/max8998_charger.c has a
comment in it stating that 'charger control is done by a current
regulator "CHARGER"', but this regulator was never added until
now.
The current values have been extracted from a downstream driver
for the SGH-T959V.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/BN6PR04MB0660E1F4A3D5A348BE88311CA3BA0@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add maintainer entries to a few ROHM devices and Linear Ranges
Linear Ranges helpers were refactored out of regulator core to lib so
that other drivers could utilize them too. (I guess power/supply drivers
and possibly clk drivers can benefit from them). As regulators is
currently the main user it makes sense the changes to linear_ranges go
through Mark's tree.
During past two years few ROHM PMIC drivers have been added to
mainstream. They deserve a supporter from ROHM side too :)
Patch 1:
Maintainer entries for few ROHM IC drivers
Patch 2:
Maintainer entry for linear ranges helpers
---
Matti Vaittinen (2):
MAINTAINERS: Add entry for ROHM power management ICs
MAINTAINERS: Add maintainer entry for linear ranges helper
MAINTAINERS | 37 +++++++++++++++++++++++++++++++++++++
1 file changed, 37 insertions(+)
base-commit: b9bbe6ed63
--
2.21.0
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
The BD71837 had a HW "feature" where changing the regulator output
voltages of other regulators but bucks 1-4 might cause spikes if
regulators were enabled. Thus SW prohibit voltage changes for other
regulators except for bucks 1-4 when regulator is enabled.
The HW colleagues did inadvertly fix this issue for BD71847 and
BD71850.
The power-good detection for LDOs can still cause false alarms if
LDO voltage is changed upwards when LDO is enabled.
Allow LDO voltage changes and disabe the power-good monioring for
the duration of the LDO voltage change and enable it after LDO
voltage has stabilized. ROHM HW colleagues measured the safety
limit of 1000uS for guaranteeing the voltage has stabilized. Let's
use that for starters and add confiurable stabilization wait-time
later if needed.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200513143921.GA22143@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lKwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HxeB/9dblIbC+28MvcEHXCcYBZBouOnrM8E
bIOMXkgEj1uL78ozOm7tMCgEpaKgv6BHdDuClCBvjbr0uOtAi0qUiv0IBotuVrdo
lq73l8l7OPz6TFFKIt8WsgwKnzdkuQC08+qrZasAdluRQnqnmkU2tvl2y9zaaaR4
6hGw+Nwx/pgeCXCa3pu+rCYwA7g0Tf8a6DDC6LyQWZameBJ1ey/YDjhJEeSmY7P7
306zs8YVxHhQMLUQ5T7DA6r/KWMNkO1SOueCqTjxWZc/XamGEcbsZG1cWrAnkoE2
VKLXBtYC75coNxIiu8ZxnQwLLdz1EQPdtg0qmzSjXJ68QjbWWzf4K1ra
=LG9G
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lPUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GuGB/9kDFxKo0DWsH6tqZGS/retk0ddT+4B
mnkkZGvoKkkDe1lh84vRbrPHhiI9LIXaj3lFgzyYeTuAi9tb77mPNnYIPLDye7bO
OvgJgovo4tK3dUVSUFatvOhuAMSZLyN2WjWRX+YeHMd1nNZSHxEz0CuG3npNtuKa
KoZd0Dfom4ds66qDlWdfonFhMJbMvQbEs4BhnfdvpD/soylyDB+29SHlhTBv8+UC
I7BNzsmVDlp/JyrX3yJbuTum9wbPaMLcyL96EbvRykmTywz5FXudffqzPfPnoQxT
rbN5DfwKsnySToUYDfp9dcIMyTF0/MtneaeBMRu2NIkpMmnicvExNrbU
=/+DM
-----END PGP SIGNATURE-----
Merge tag 'linear-ranges-lib' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-5.8
lib: Add linear ranges helper library and start using it
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
Change the regulator helpers to use common linear_ranges code.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/64f01d5e381b8631a271616b7790f9d5640974fb.1588944082.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following coccicheck warning:
drivers/regulator/db8500-prcmu.c:184:1-17: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200506061726.19289-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit dca0b44957 ("regulator: Use
driver_deferred_probe_timeout for regulator_init_complete_work"),
as we ended up reverting the default deferred_probe_timeout
value back to zero, to preserve behavior with 5.6 we need to
decouple the regulator timeout which was previously 30 seconds.
This avoids breaking some systems that depend on the regulator
timeout but don't require the deferred probe timeout.
Cc: linux-pm@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200429172349.55979-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BD71837 had a HW "feature" where changing the regulator output
voltages of other regulators but bucks 1-4 might cause spikes if
regulators were enabled. Thus SW prohibit voltage changes for other
regulators except for bucks 1-4 when regulator is enabled.
The HW colleagues did inadvertly fix this issue for BD71847 and
BD71850. Remove voltage change restrictions from other PMICs but
BD71837.
The LDO voltage changing is still restricted. I did not yet receive
answer whether there is voltage spikes to be expected for LDOs. I
only know that the power-good detection for LDOs can cause false
alarms if LDO voltage is changed when LDO is enabled. We might be
able to work-around this by disabling the power-good monioring for
the duration of the LDO voltage change - but as I said, I don't
know yet. Let's fix it later if we can confirm that also LDO voltage
changes are safe.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200428092930.GA9721@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding regulator driver for the Maxim max77826 device.
The max77826 PMIC contains a high-efficiency BUCK regulator, a BUCK
BOOST regulator and 15 LDOs. It is designed for smartphone and tablet
applications and is accessed over I2C.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200414172250.2363235-2-iskren.chernev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variables ret and val are being initialized with values that are
never read and are being updated later with a new value. The
initializations are redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20200410133406.24458-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following gcc warning:
drivers/regulator/ab8500.c:195:27: warning: ‘ldo_vdmic_voltages’ defined
but not used [-Wunused-const-variable=]
static const unsigned int ldo_vdmic_voltages[] = {
^~~~~~~~~~~~~~~~~~
drivers/regulator/ab8500.c:169:27: warning: ‘fixed_3300000_voltage’
defined but not used [-Wunused-const-variable=]
static const unsigned int fixed_3300000_voltage[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/regulator/ab8500.c:142:27: warning: ‘ldo_sdio_voltages’ defined
but not used [-Wunused-const-variable=]
static const unsigned int ldo_sdio_voltages[] = {
^~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200410073343.39031-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it easier to identify regulator consumers when consumer device
uses more than one supply.
Before:
regulator ena use open bypass voltage current min max
-----------------------------------------------------------------------------------
regulator-dummy 1 0 2 0 0mV 0mA 0mV 0mV
1-0010 0mV 0mV
1-0010 0mV 0mV
After:
regulator ena use open bypass voltage current min max
-----------------------------------------------------------------------------------
regulator-dummy 1 0 2 0 0mV 0mA 0mV 0mV
1-0010-vccio 0mV 0mV
1-0010-vcc33 0mV 0mV
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/731a4b299c6ae0ee9d8995157600a3477f21a36c.1585959068.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following gcc warning:
drivers/regulator/qcom_rpm-regulator.c:607:34: warning: ‘pm8921_ftsmps’
defined but not used [-Wunused-const-variable=]
static const struct qcom_rpm_reg pm8921_ftsmps = {
^~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200409114026.38383-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
At one point in the release cycle I managed to fat finger things and
apply some SPI fixes onto a regulator branch and merge that into the SPI
tree, then pull in a change shared with the MTD tree moving the Mediatek
quadspi driver over to become the Mediatek spi-nor driver in the SPI
tree. This has made a mess which I only just noticed while preparing
this and I can't see a sensible way to unpick things due to other
subsequent merge commits especially the pull from MTD so it looks like
the most sensible thing to do is give up and combine the two pull
requests - I hope this is OK. Sorry about this, I've changed some bits
of workflow which should hopefully help me spot such issues earlier in
future.
Fortunately both subsystems were fairly quiet this cycle, the highlights
are:
regulator:
- Support for Monoloithic Power Systems MP5416, MP8867 and MPS8869 and
Qualcomm PMI8994 and SMB208.
SPI:
- Lots of enhancements for spi-fsl-dspi, including XSPI mode support,
from Vladimir Oltean.
- Support for amlogic Meson G12A, IBM FSI, Mediatek spi-nor (moved from
MTD), NXP i.MX8Mx, Rockchip PX30, RK3308 and RK3328, and Qualcomm
Atheros AR934x/QCA95xx.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl6B5OUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0F64B/wMN9AALiI+L8yLWbhlCebJLrtX4Nc5
2Pe25eJNnYRor+s8SxWK7rJ1IlMHQv/lkD2kCtjtmAvLXQwxyy2r8gW0hsZ8bmUS
O1otrQ8wqfY8Enr8w/qXBMxR46U6vs1sfKDsAEPPUDt5voPbiDGpNazHytWU5Nnp
yLh/8LdACFbanueeth5b14aYZNRVHb04Dh6yDjZOKu0zgNtBmkTQGNN8A4jJyVHC
0SFE0vo1nYsc2w02U6i9ko/GEA/lRSTNZZslXif3wvZQXvy0EgC8sQGLbCdxu8ES
K2EBdeSCaMEoU+s2mFZ2Fuvd3RvGliHxWbn4SZtpaDp+/SBIu52kM4B+
=Eqwk
-----END PGP SIGNATURE-----
Merge tag 'regulator-spi-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi and regulator updates from Mark Brown:
"At one point in the release cycle I managed to fat finger things and
apply some SPI fixes onto a regulator branch and merge that into the
SPI tree, then pull in a change shared with the MTD tree moving the
Mediatek quadspi driver over to become the Mediatek spi-nor driver in
the SPI tree.
This has made a mess which I only just noticed while preparing this
and I can't see a sensible way to unpick things due to other
subsequent merge commits especially the pull from MTD so it looks like
the most sensible thing to do is give up and combine the two pull
requests.
Fortunately both subsystems were fairly quiet this cycle, the
highlights are:
regulator:
- Support for Monoloithic Power Systems MP5416, MP8867 and MPS8869
and Qualcomm PMI8994 and SMB208.
SPI:
- Lots of enhancements for spi-fsl-dspi, including XSPI mode support,
from Vladimir Oltean.
- Support for amlogic Meson G12A, IBM FSI, Mediatek spi-nor (moved
from MTD), NXP i.MX8Mx, Rockchip PX30, RK3308 and RK3328, and
Qualcomm Atheros AR934x/QCA95xx"
* tag 'regulator-spi-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (118 commits)
spi: efm32: Convert to use GPIO descriptors
regulator: qcom_smd: Add pmi8994 regulator support
regulator: da9063: Fix get_mode() functions to read sleep field
spi: spi-fsl-lpspi: Replace zero-length array with flexible-array member
spi: spi-s3c24xx: Replace zero-length array with flexible-array member
spi: stm32: Fix comments compilation warnings
spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses
spi: spi-fsl-dspi: Add support for LS1028A
spi: spi-fsl-dspi: Move invariant configs out of dspi_transfer_one_message
spi: spi-fsl-dspi: Fix interrupt-less DMA mode taking an XSPI code path
spi: spi-fsl-dspi: Avoid NULL pointer in dspi_slave_abort for non-DMA mode
spi: spi-fsl-dspi: Replace interruptible wait queue with a simple completion
spi: spi-fsl-dspi: Protect against races on dspi->words_in_flight
spi: spi-fsl-dspi: Avoid reading more data than written in EOQ mode
spi: spi-fsl-dspi: Fix bits-per-word acceleration in DMA mode
spi: spi-fsl-dspi: Fix little endian access to PUSHR CMD and TXDATA
spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR
regulator: driver.h: fix regulator_map_* function names
regulator: da9063: fix suspend
spi: mxs: Drop GPIO includes
...
The pmi8994 is commonly found on MSM8996 based devices, such as the
Dragonboard 820c, where it supplies power to a number of LDOs on the
primary PMIC.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324041424.518160-1-bjorn.andersson@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
get_mode() is used to retrieve the active mode state. Settings-A
config is used during active state, whilst Settings-B is for
suspend. This means we only need to check the sleep field of each
buck and LDO as that field solely relates to Settings-A config.
This change is a clone of the get_mode() update which was committed
as part of:
- regulator: da9062: fix suspend_enable/disable preparation
[a72865f057]
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200324092516.60B5C3FB8D@swsrvapps-01.diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The .set_suspend_enable() and .set_suspend_disable() methods are not
supposed to immediately change the regulator state but just indicated
if the regulator should be enabled or disabled when standby mode is
entered (by a hardware signal).
However currently they set control the SEL bits in the DVC registers,
which causes the voltage to change to immediately between the "A"
(normal) and "B" (standby) values as programmed and does nothing for
the enable state...
This means that "regulator-on-in-suspend" does not work (the regulator
is switched off when the PMIC enters standby mode on the hardware
signal) and, potentially, depending on the A and B voltage
configurations the voltage could be incorrectly changed *before*
actually entering suspend.
The right bit to use for the functionality is the "CONF" bit in the
"CONT" register.
The detailed register description says "Sequencer target state"
for this bit which is not very clear but the functional description
is clearer.
>From 5.1.5 System Enable:
De-asserting SYS_EN (changing from active to passive state)
clears control SYSTEM_EN which triggers a power down sequence
into hibernate/standby mode
...
With the exception of supplies that have the xxxx_CONF control
bit asserted, all regulators in power domains POWER1, POWER, and
SYSTEM are sequentially disabled in reverse order.
Regulators with the <x>_CONF bit set remain on but change the
active voltage controlregisters from V<x>_A to V<x>_B
(if V<x>_B is notalready selected).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Link: https://lore.kernel.org/r/1584461691-14344-1-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Mark Brown <broonie@kernel.org>
MP8867 is an I2C-controlled adjustable voltage regulator made by
Monolithic Power Systems. The difference between MP8867 and MP8869
are:
1.If V_BOOT, the vref of MP8869 is fixed at 600mv while vref of
MP8867 is determined by the I2C control.
2.For MP8867, when setting voltage, if the step is within 5, we
need to manually set the GO BIT to 0.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223127.4b1ecc92@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
The MP8869 from Monolithic Power Systems is a single output DC/DC
converter. The voltage can be controlled via I2C.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200316223020.1a6d92ae@xhacker
Signed-off-by: Mark Brown <broonie@kernel.org>
With current code:
st-gyro-i2c i2c-PRP0001:00: i2c-PRP0001:00 supply vdd not found, using dummy regulator
which looks a bit oververbose.
Replace this with simplified format string for the above case, and drop
"deviceless" case since for all dev_*() macros used in _regulator_get()
the "(null)" will be printed anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200312183245.1612-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of small fixes, one for a minor issue in the stm32-vrefbuf
driver and a documentation fix in the Qualcomm code.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5ie5ITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0J5lB/wOdphcQj9YKbq1fO5Z2i4zROn85dbT
JREqpS5SNY+znox3WFct08L7xyrUBwFgZwzlF0KTnoBfNLznjcdY34YNSswWMZzY
vo0frRtEzdetjtQOYzuKfr+cWSozNLFCz4rGb9eMZicR28yaU+WluKlNLtwgkgq0
WEqyDZKK1KhVZYDJPVY6gb3NgTYlUvaJyRKEFGxSNHTDR9qL5koP7ym1yIqBjAu/
N596CtL8A24z9x7Wlmt2I9m13S/YXPUbDibYU10UC6amFWfsiuZ0hi577ToXvr1X
PruiRr63WgFlHGedAjsyfW1y1O9oBvGksb9rlBmwYzssgnuqV5DTuxsB
=s+Ng
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small fixes, one for a minor issue in the stm32-vrefbuf
driver and a documentation fix in the Qualcomm code"
* tag 'regulator-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: stm32-vrefbuf: fix a possible overshoot when re-enabling
regulator: qcom_spmi: Fix docs for PM8004
The regulator_init_complete_work logic defers the cleanup for an
arbitrary 30 seconds of time to allow modules loaded by userland
to start.
This arbitrary timeout is similar to the
driver_deferred_probe_timeout value, and its been suggested we
align these so users have a method to extend the timeouts as
needed.
So this patch changes the logic to use the
driver_deferred_probe_timeout value for the delay value if it
is set (using a delay of 0 if it is not).
Cc: linux-pm@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200225050828.56458-7-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There maybe an overshoot, when disabling, then re-enabling vrefbuf
too quickly. VREFBUF is used by ADC/DAC on some boards. When re-enabling
too quickly, an overshoot on the reference voltage make the conversions
inaccurate for a short period of time.
- Don't put the VREFBUF in HiZ when disabling, to force an active
discharge.
- Enforce a 1ms OFF/ON delay
Fixes: 0cdbf481e9 ("regulator: Add support for stm32-vrefbuf")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Message-Id: <1583312132-20932-1-git-send-email-fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_regulator_register() could return -EPROBE_DEFER when trying to
get init data and NOT all resources are available at that time, for
this case, error message is better to be present for debug level ONLY.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1583243052-1930-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Deferred probe is an expected return value for devm_pwm_get(). Given
that the driver deals with it properly, rather than warn on probe
deferral, only output a message on probe deferral if debug level
prints are enabled.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200302141428.14119-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Smb208 regulators are used on some ipq806x soc.
Add support for it to make it avaiable on some routers
that use it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200219163711.479-1-ansuelsmth@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It works incidentally, because AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN
is non-zero, but the false branch value really should be just 0.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200222235634.243805-1-megous@megous.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200211234612.GA28682@embeddedor
Signed-off-by: Mark Brown <broonie@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211234710.GA29532@embeddedor
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding regulator driver for the device mp5416.
The MP5416 PMIC device contains four DC-DC buck converters and
five regulators, accessed over I2C.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Link: https://lore.kernel.org/r/20200204110419.25933-3-sravanhome@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_request_threaded_irq() already returns 0 on success
and negative error code on failure. So return from this itself
can be used while preserving error log in case of failure.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Link: https://lore.kernel.org/r/1580996996-28798-1-git-send-email-gupt21@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit fixes following errors & warnings in this driver
as reported by checkpatch.pl:
- WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
- WARNING: line over 80 characters
- ERROR: space prohibited before that ',' (ctx:WxW)
- ERROR: code indent should use tabs where possible
- WARNING: Block comments use * on subsequent lines
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Link: https://lore.kernel.org/r/1580996917-28494-1-git-send-email-gupt21@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add vin_supply to the regulator description to support a nice
regulator tree.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200203110034.1448-1-m.reichl@fivetechno.de
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----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=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Few ROHM PMICs allow setting the voltage states for different system states
like RUN, IDLE, SUSPEND and LPSR. States are then changed via SoC specific
mechanisms. bd718x7 driver implemented device-tree parsing functions for
these state specific voltages. The parsing functions can be re-used by
other ROHM chip drivers like bd71828. Split the generic functions from
bd718x7-regulator.c to rohm-regulator.c and export them for other modules
to use.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Thanks to Stephen Boyd I today learned we can use platform_device_id
to do device and module matching for MFD sub-devices!
Do device matching using the platform_device_id instead of using
explicit module_aliases to load modules and custom parent-data field
to do module loading and sub-device matching.
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the exported symbols introduced by commit e915331149
("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
from EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL(), like is used for all the core
parts.
Fixes: e915331149 ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200120123921.1204339-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix defines for MPQ7920_MASK_BUCK_ILIM and MPQ7920_DISCHARGE_ON
Remove unused MPQ7920_REG_REGULATOR_EN1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20200115002953.14731-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200116023344.163592-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
`cat /sys/kernel/debug/regulator/regulator_summary` ends on a deadlock
when you have a voltage controlled regulator (vctrl).
The problem is that the vctrl_get_voltage() and vctrl_set_voltage() calls the
regulator_get_voltage() and regulator_set_voltage() and that will try to lock
again the dependent regulators (the regulator supplying the control voltage).
Fix the issue by exporting the unlocked version of the regulator_get_voltage()
and regulator_set_voltage() API so drivers that need it, like the voltage
controlled regulator driver can use it.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Reported-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200116094543.2847321-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator_is_equal() helper to compare whether two regulators are
the same. This is useful for checking whether two separate regulators
in a driver are actually the same supply.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20191220164450.1395038-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Both *dev and *rdev are only used in .probe, so use local variable instead.
Also remove mpq7920_regulator_register() because it is so trivial and
there is only one caller.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20200114124449.28408-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few trivial clean up:
* Make ipq4019_regulator_voltage_ops and vmmc_regulator const
* Make ipq4019_vmmcq_regmap_config static
* Use regulator_map_voltage_ascend
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20200114065847.31667-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using devm_regulator_register() so no need to call
regulator_unregister() in ipq4019_regulator_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20200114065847.31667-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Nowdays ROHM_CHIP_TYPE_AMOUNT includes not only BD71837/BD71847 but also
BD70528/BD71828 which are not supported by this driver. So it seems not
necessay to have pmic_regulators[ROHM_CHIP_TYPE_AMOUNT] as mapping table.
Simplify the code by removing struct bd718xx_pmic_inits and
pmic_regulators[ROHM_CHIP_TYPE_AMOUNT].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20200108014256.11282-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This introduces the IPQ4019 VQMMC LDO driver needed for
the SD/EMMC driver I/O level operation.
This will enable introducing SD/EMMC support for the built-in controller.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20200112113003.11110-1-robert.marko@sartura.hr
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new .probe_new for i2c drivers.
These drivers do not use const struct i2c_device_id * argument, so convert
them to utilise the simplified i2c driver registration.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20200109155808.22003-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a typo in the error checking. We should be checking
"->rdev[i]" instead of just "->rdev".
Fixes: 6501c1f54a ("regulator: mpq7920: add mpq7920 regulator driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200113125805.xri6jqoxy2ldzqyg@kili.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding regulator driver for the device mpq7920.
The MPQ7920 PMIC device contains four DC-DC buck converters and
five regulators, is designed for automotive and accessed over I2C.
Fixed sparse warning reported on this patch
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Link: https://lore.kernel.org/r/20200109195346.30270-1-sravanhome@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MP8859 from Monolithic Power Systems is a single output DC/DC
converter. The voltage can be controlled via I2C.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/20200106211633.2882-2-m.reichl@fivetechno.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200103171131.9900-20-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Three small fixes here, two the result of Axel Lin's amazing work
tracking down inconsistencies in drivers.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4TMHsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HADB/9B1xZUrTCDH4Fsd+T/iRtIpdaTOnxI
FNf/O2maHM4fyNeyrK7POzs+Dr2Oa7a+HI/EsWq20g2venDxxF9W8R3/4QQt12Id
S4MBP6gYCxQwH9hleDyCNn2IilRqiMkJUsgHRDcAqAtW1T310PRpU8xkZM6uAwyM
24ZGUdtnq9CGHssvzbqmbOCfSgDwt7cU9MdYhcigcJK8hfFIu6cwMHFX4lgZkd+7
E3vs2YvNJh8KnNC/a0rMb9pOUgbCJ9HxP2SGQ/Npa6KjhP2ZLB9Xw3ifQC55+o3p
pkbJK3Bv9dFoODE4g+vqqw/reaE58/rcbUmiYd4Du4a4US/BwAW+4CX4
=srs1
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Three small fixes here, two the result of Axel Lin's amazing work
tracking down inconsistencies in drivers"
* tag 'regulator-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: bd70528: Remove .set_ramp_delay for bd70528_ldo_ops
regulator: axp20x: Fix axp20x_set_ramp_delay
regulator: axp20x: Fix AXP22x ELDO2 regulator enable bitmask
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The .set_ramp_delay should be for bd70528_buck_ops only.
Setting .set_ramp_delay for for bd70528_ldo_ops causes problem because
BD70528_MASK_BUCK_RAMP (0x10) overlaps with BD70528_MASK_LDO_VOLT (0x1f).
So setting ramp_delay for LDOs may change the voltage output, fix it.
Fixes: 99ea37bd1e ("regulator: bd70528: Support ROHM BD70528 regulator block")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200101022406.15176-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code set incorrect bits when set ramp_delay for AXP20X_DCDC2,
fix it.
Fixes: d29f54df8b ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20191221081049.32490-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify LDO6 voltage getting on BD71828 by removing the
get_voltage call-back and providing the fixed voltage in
regulator_desc instead
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191219113444.GA28299@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
A copy-paste error was introduced when bitmasks were converted to
macros, incorrectly setting the enable bitmask for ELDO2 to the one
for ELDO1 for the AXP22x units.
Fix it by using the correct macro.
On affected boards, ELDO1 and/or ELDO2 are used to power the camera,
which is currently unsupported.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20191218044720.21990-1-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
A small set of fixes for mostly minor issues here, the only real code
ones are Wen Yang's fixes for error handling in the core and Christian
Marussi's list_voltage() change which is a fix for disruptively bad
performance for regulators with continuous voltage control (which are
rare).
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl34yr4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KJyB/97dTSIk+gJxwFSc9tTPbMvSGvGqoEL
AUE8JSHVNqav9IdFKwtzxa6dnjVy1U23ySemeOAvabmLmyJjoIRMJAeA10+OwcMl
2dq3j/3z6Vl305QSVNu3yMcxp2XtQ8nhKOpNz+rDGwRAvr08YBjdrCPv4dbiv/ei
G7z7sOwcNNACE7CNGat3kOh9cOJm3wVzls1bF5Ix+kDlWH6v591GSY1MMXdhx6Tj
RS9HCjj8Gp4O+vnJH4r/AVkOyZp8SOSOje/+81pF68wc2g+S7XV8hE4kDipRlHS3
4aKpBbfyA4twjZ4AOCVGTwJrGXh6W7GhDlrbWCYyQ3y2hOfwgbh8sKzo
=Lx6m
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of fixes for mostly minor issues here, the only real code
ones are Wen Yang's fixes for error handling in the core and Christian
Marussi's list_voltage() change which is a fix for disruptively bad
performance for regulators with continuous voltage control (which are
rare)"
* tag 'regulator-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: rn5t618: fix module aliases
regulator: max77650: add of_match table
regulator: core: avoid unneeded .list_voltage calls
regulator: s5m8767: Fix a warning message
regulator: core: fix regulator_register() error paths to properly release rdev
regulator: fix use after free issue
ROHM BD71828 is a power management IC containing 7 bucks and 7 LDOs. Bucks
1,2,6 and 7 can be assigned to a regulator group controlled by run-levels.
Eg. Voltages and enable/disable statuses for specific run-levels (run0 to
run3) can be set via register interface and run level changes can then be
done either via I2C or GPIO.
This initial commit does not support assigning bucks to be controlled via
run-levels but only allows them to be individually controlled.
LDO5 voltage can also be controlled by GPIO2 pin and register interfaces
but this driver only supports the control via register.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/5b1c4a22c7945e97ff2a7924abfeb3239043f8eb.1576054779.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
platform device aliases were missing, preventing
autoloading of module.
Fixes: 811b700630 ("regulator: rn5t618: add driver for Ricoh RN5T618 regulators")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20191211221600.29438-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the regulator driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20191210100725.11005-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS
(Dynamic Voltage Scaling). These GPIOs are entirely optional but a
dev_warn() appeared when cleaning this driver to use a more up-to-date
gpiod API. At least reduce the log level to 'info' as it is totally
fine to not populate these GPIO on a hardware design.
This change is trivial but it is worth not polluting the logs during
bringup phase by having real warnings and errors sorted out
correctly.
Fixes: a13eaf02e2 ("regulator: rk808: make better use of the gpiod API")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Inside machine_constraints_voltage() a loop is in charge of verifying that
each of the defined voltages are within the configured constraints and
that those constraints are in fact compatible with the available voltages'
list.
When the registered regulator happens to be defined with a wide range of
possible voltages the above O(n) loop can be costly.
Moreover since this behaviour is triggered during the registration process,
it means also that it can be easily triggered at probe time, slowing down
considerably some module loading.
On the other side if such wide range of voltage values happens to be also
continuous and without discontinuity of any kind, the above potentially
cumbersome operation is also useless.
For these reasons, avoid such .list_voltage poll loop when regulator is
described as 'continuous_voltage_range' as is, indeed, similarly already
done inside regulator_is_supported_voltage().
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20191209125239.46054-1-cristian.marussi@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several issues with the error handling code of
the regulator_register() function:
ret = device_register(&rdev->dev);
if (ret != 0) {
put_device(&rdev->dev); --> rdev released
goto unset_supplies;
}
...
unset_supplies:
...
unset_regulator_supplies(rdev); --> use-after-free
...
clean:
if (dangling_of_gpiod)
gpiod_put(config->ena_gpiod);
kfree(rdev); --> double free
We add a variable to record the failure of device_register() and
move put_device() down a bit to avoid the above issues.
Fixes: c438b9d017 ("regulator: core: Move registration of regulator device")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191201030250.38074-1-wenyang@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is caused by dereferencing 'rdev' after put_device() in
the _regulator_get()/_regulator_put() functions.
This patch just moves the put_device() down a bit to avoid the
issue.
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191124145835.25999-1-wenyang@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-EINVAL is not a valid return value for .of_map_mode, return
REGULATOR_MODE_INVALID instead.
Fixes: 844e7492ee ("regulator: da9062: add of_map_mode support for bucks")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20191122045154.802-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133949.13996-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tell the regulator framework to retrieve regulator init
data from the 'regulator' subnode, or from the parent mfd
device's platform data.
Example:
i2c0 {
tps61052@33 {
compatible = "ti,tps61052";
reg = <0x33>;
regulator {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
};
};
Tree: next-20191118
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191119154611.29625-3-TheSven73@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/regulator/vexpress-regulator.c:78:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1574074762-34629-1-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds of_map_mode support for bucks to set regulator modes
from within regulator framework.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Link: https://lore.kernel.org/r/1573652416-9848-3-git-send-email-chf.fritz@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refactors buck modes into a header file so that device trees
can make use of these mode constants.
The new header filename uses da9063 because DA9063 was the earlier chip
and its driver code will want updating at some point in a similar manner.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/1573652416-9848-2-git-send-email-chf.fritz@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Boot-on regulators are always kept on because their use_count value
is now incremented at boot time and never cleaned.
Only increment count value for alway-on regulators.
regulator_late_cleanup() is now able to power off boot-on regulators
when unused.
Fixes: 05f224ca66 ("regulator: core: Clean enabling always-on regulators + their supplies")
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Link: https://lore.kernel.org/r/20191113102737.27831-1-p.paillet@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
device_link_add() might not always succeed depending on the type of
device link and the rest of the dependencies in the system. If
device_link_add() didn't succeed, then we shouldn't try to remove the
link later on as it might remove a link someone else created.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20191115000438.45970-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The USB regulator was removed for AB8500 in
commit 41a06aa738 ("regulator: ab8500: Remove USB regulator").
It was then added for AB8505 in
commit 547f384f33 ("regulator: ab8500: add support for ab8505").
However, there was never an entry added for it in
ab8505_regulator_match. This causes all regulators after it
to be initialized with the wrong device tree data, eventually
leading to an out-of-bounds array read.
Given that it is not used anywhere in the kernel, it seems
likely that similar arguments against supporting it exist for
AB8505 (it is controlled by hardware).
Therefore, simply remove it like for AB8500 instead of adding
an entry in ab8505_regulator_match.
Fixes: 547f384f33 ("regulator: ab8500: add support for ab8505")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191106173125.14496-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Depends on board design, the gpio controlling regulator may
connects with a big capacitance. When need off, it takes some time
to let the regulator to be truly off. If not add enough delay, the
regulator might have always been on, so introduce off-on-delay to
handle such case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1572311875-22880-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes memory leak which should happen if regulator's coupling
fails to initialize.
Fixes: d8ca7d184b ("regulator: core: Introduce API for regulators coupling customization")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20191025002240.25288-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window. That fixes one of
the last two errors preventing successful execution of "make dt_binding_check"
which will be enourmously helpful for DT schema development.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl2wgdsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PxRB/4uqIJR3n3mIdrHtB0DVaZEWm7jsC6L
PUYZZH//EkLe6d5hgb2qKYrpIJIlKdrVukySl/uyE//gxNH6BUOgggfAGx5qIAjN
qGB6dv+M+AWiDW3hRkMPQ/RnnNgm/llM5cOIHjFqHvYiVbfppIYkKFoCMS8BPWDT
8DUlSwRTGHDKlR1Zn7+HJqvE+eoDAgTVnwoDKaZUh6sL2UrNA8nf0irsB6yq1n+u
1O9D02oTd01tw8Qy3/zAdL+E1RfHbYAuobz367mRUaEzZg6AFG3eWkuJdGIYR+14
C5ypBi/e0zXOyWHEjA5qfxXNbw0U+j4R37iPdgvQvhVQp7D8gIPqXIxX
=r41P
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window.
That fixes one of the last two errors preventing successful execution
of "make dt_binding_check" which will be enormously helpful for DT
schema development"
* tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: Fix PMIC5 BoB min voltage
regulator: pfuze100-regulator: Variable "val" in pfuze100_regulator_probe() could be uninitialized
regulator: lochnagar: Add on_off_delay for VDDCORE
regulator: ti-abb: Fix timeout in ti_abb_wait_txdone/ti_abb_clear_all_txdone
regulator: da9062: fix suspend_enable/disable preparation
dt-bindings: fixed-regulator: fix compatible enum
regulator: fixed: Prevent NULL pointer dereference when !CONFIG_OF
regulator: core: make regulator_register() EPROBE_DEFER aware
regulator: of: fix suspend-min/max-voltage parsing
The bd70528 regulator driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell for
regulators is added.
Fixes: 99ea37bd1e ("regulator: bd70528: Support ROHM BD70528 regulator block")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20191023121452.GA1812@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
The sleep flag bit decides the mode for BUCK_MODE_MANUAL case, simplify
the logic as the result is the same.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20191007115009.25672-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The implement is exactly the same as rk808_set_suspend_voltage, so just
use rk808_set_suspend_voltage instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20191008010628.8513-3-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20191008010628.8513-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_get_from_of_node() is being retired in favor of
fwnode_gpiod_get_index(), that behaves similar to gpiod_get_index(),
but can work with arbitrary firmware node. It will also be able to
support secondary software nodes.
Let's switch this driver over.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20191004231017.130290-8-dmitry.torokhov@gmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_fwnode_get_index_gpiod_from_child() is going away as the name is
too unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Note that we no longer need to check for NULL as devm_fwnode_gpiod_get()
will return -ENOENT if GPIO is missing.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20191004231017.130290-7-dmitry.torokhov@gmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get_from_of_node() is being retired in favor of
devm_fwnode_gpiod_get_index(), that behaves similar to
devm_gpiod_get_index(), but can work with arbitrary firmware node. It
will also be able to support secondary software nodes.
Let's switch this driver over.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20191004231017.130290-6-dmitry.torokhov@gmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get_from_of_node() is being retired in favor of
devm_fwnode_gpiod_get_index(), that behaves similar to
devm_gpiod_get_index(), but can work with arbitrary firmware node. It
will also be able to support secondary software nodes.
Let's switch this driver over.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20191004231017.130290-5-dmitry.torokhov@gmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get_from_of_node() is being retired in favor of
devm_fwnode_gpiod_get_index(), that behaves similar to
devm_gpiod_get_index(), but can work with arbitrary firmware node. It
will also be able to support secondary software nodes.
Let's switch this driver over.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20191004231017.130290-4-dmitry.torokhov@gmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get_from_of_node() is being retired in favor of
[devm_]fwnode_gpiod_get_index(), that behaves similar to
devm_gpiod_get_index(), but can work with arbitrary firmware node. It
will also be able to support secondary software nodes.
Let's switch this driver over.
Note that now that we have a good non-devm API for getting GPIO from
arbitrary firmware node, there is no reason to use devm API here as
regulator core takes care of managing lifetime of "enable" GPIO and we
were immediately detaching requested GPIO from devm anyway.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20191004231017.130290-3-dmitry.torokhov@gmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get_from_of_node() is being retired in favor of
devm_fwnode_gpiod_get_index(), that behaves similar to
devm_gpiod_get_index(), but can work with arbitrary firmware node. It
will also be able to support secondary software nodes.
Let's switch this driver over.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20191004231017.130290-2-dmitry.torokhov@gmail.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only the desc field is really used, so use struct regulator_desc instead.
Then struct pbias_regulator_data can be removed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20191007114320.20977-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's more straightforward to use for statement here.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Link: https://lore.kernel.org/r/20191007115009.25672-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Inside function max8907_regulator_probe(), variable val could
be uninitialized if regmap_read() fails. However, val is used
later in the if statement to decide the content written to
"pmic", which is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20191003175813.16415-1-yzhai003@ucr.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
In function pfuze100_regulator_probe(), variable "val" could be
initialized if regmap_read() fails. However, "val" is used to
decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20190929170957.14775-1-yzhai003@ucr.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
The VDDCORE regulator takes a good length of time to discharge down, so
add an on_off_delay to ensure DCVDD is removed before it is powered on
again.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191001132017.1785-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/pcap-regulator.c:89:27: warning:
SW3_table defined but not used [-Wunused-const-variable=]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190928085540.45332-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sleep flag bit decides the mode for BUCK_MODE_MANUAL case, simplify
the logic as the result is the same.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20190926055128.23434-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This Power IC is used in combination with various PMIC combos,
generally found on boards with MSM8992, MSM8994, MSM8996,
MSM8956, MSM8976 and others, usually at address 0x5 on the SPMI
bus, and its usual usage is to provide power to the GPU and/or
to the CPU clusters (APC0/APC1).
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20190921095043.62593-6-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8950 provides 6 SMPS regulators, of which 5 HFSMPS
and one FTSMPS2.5 (s5), and 23 LDOs.
Add these to the RPM regulator driver.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20190921095043.62593-4-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8950 has 5 HFSMPS, 1 FTSMPS2.5 (s5, controlling APC voltage)
and 23 LDO regulators.
Add the configuration for this chip.
Signed-off-by: Angelo G. Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20190921095043.62593-3-kholk11@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ti_abb_wait_txdone() may return -ETIMEDOUT when ti_abb_check_txdone()
returns true in the latest iteration of the while loop because the timeout
value is abb->settling_time + 1. Similarly, ti_abb_clear_all_txdone() may
return -ETIMEDOUT when ti_abb_check_txdone() returns false in the latest
iteration of the while loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20190929095848.21960-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the suspend reg_field maps to the pmic voltage selection bits
and is used during suspend_enabe/disable() and during get_mode(). This
seems to be wrong for both use cases.
Use case one (suspend_enabe/disable):
Those callbacks are used to mark a regulator device as enabled/disabled
during suspend. Marking the regulator enabled during suspend is done by
the LDOx_CONF/BUCKx_CONF bit within the LDOx_CONT/BUCKx_CONT registers.
Setting this bit tells the DA9062 PMIC state machine to keep the
regulator on in POWERDOWN mode and switch to suspend voltage.
Use case two (get_mode):
The get_mode callback is used to retrieve the active mode state. Since
the regulator-setting-A is used for the active state and
regulator-setting-B for the suspend state there is no need to check
which regulator setting is active.
Fixes: 4068e5182a ("regulator: da9062: DA9062 regulator driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20190917124246.11732-2-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data which has NULL test for match before
dereference match->data. Add NULL test for drvtype so it still works
for fixed_voltage_ops when !CONFIG_OF.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190922022928.28355-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
Sometimes it can happen that the regulator_of_get_init_data() can't
retrieve the config due to a not probed device the regulator depends on.
Fix that by checking the return value of of_parse_cb() and return
EPROBE_DEFER in such cases.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-4-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the regulator-suspend-min/max-microvolt must be within the
root regulator node but the dt-bindings specifies it as subnode
properties for the regulator-state-[mem/disk/standby] node. The only DT
using this bindings currently is the at91-sama5d2_xplained.dts and this
DT uses it correctly. I don't know if it isn't tested but it can't work
without this fix.
Fixes: f7efad10b5 ("regulator: add PM suspend and resume hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-3-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_uV_show() is missing error handling if regulator_get_voltage_rdev()
returns negative values. Instead it prints the errno as a string, e.g. -EINVAL
as "-22" which could be interpreted as -22 µV.
We also do not need to hold the lock while converting the integer to a string.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/f37f2a1276efcb34cf3b7f1a25481175be048806.1568143348.git.hns@goldelico.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes 11da04af0d, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply "enable"
when moving to using devm_gpiod_get_from_of_node().
Fixes: 11da04af0d ("regulator: da9211: Pass descriptors instead of GPIO numbers")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170246.GA56792@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes 96392c3d8c, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply
"maxim,ena" when moving to using devm_gpiod_get_from_of_node().
Fixes: 96392c3d8c ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170050.GA55530@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.
This is a special regulator-fixed that has to have a clock, from which
the regulator gets switched on and off.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190910062103.39641-2-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The value under 's2mps11->ext_control_gpiod[i]' is assigned to local
variable and used in probe in one place before. Use it consistently
later so code will be easier to read.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190909155723.24734-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev->regmap/&rdev->dev instead of lp87565->regmap/lp87565->dev.
In additional, the lp87565->dev actually is the parent mfd device,
so the dev_err message is misleading here with lp87565->dev.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190908035720.17748-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS GPIO line is clearly optional GPIO (and marked as such in the
binding document) and we should handle it accordingly. The current code
treats all errors as meaning that there is no GPIO defined, which is
wrong, as it does not handle deferrals raised by the underlying code
properly, nor does it recognize non-existing GPIO from any other
initialization error.
As far as I can see the only reason the driver, unlike all others,
is using OF-specific devm_gpiod_get_from_of_node() so that it can
assign a custom label to the selected GPIO line. Given that noone else
needs that, it should not be doing that either.
Let's switch to using more appropriate devm_gpiod_get_optional().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190904214200.GA66118@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the array en_mask on the stack but instead make it
static const. Makes the object code smaller by 87 bytes.
Before:
text data bss dec hex filename
12967 3408 0 16375 3ff7 drivers/regulator/lp8788-ldo.o
After:
text data bss dec hex filename
12816 3472 0 16288 3fa0 drivers/regulator/lp8788-ldo.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190906130632.6709-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of a missing (optional) gpio don't fall through up to
"ti,active-discharge-time-us" due to
devm_fwnode_get_index_gpiod_from_child() returning NULL (since
gpiod_get_from_of_node() returned NULL) but rather indicate success as
intended.
This makes the driver probe correctly when e.g. only the enable gpio is
given.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/363bd50cc7c60daa57d614a341d1fd649f05194c.1567625660.git.agx@sigxcpu.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel has no way of knowing when we have finished instantiating
drivers, between deferred probe and systems that build key drivers as
modules we might be doing this long after userspace has booted. This has
always been a bit of an issue with regulator_init_complete since it can
power off hardware that's not had it's driver loaded which can result in
user visible effects, the main case is powering off displays. Practically
speaking it's not been an issue in real systems since most systems that
use the regulator API are embedded and build in key drivers anyway but
with Arm laptops coming on the market it's becoming more of an issue so
let's do something about it.
In the absence of any better idea just defer the powering off for 30s
after late_initcall(), this is obviously a hack but it should mask the
issue for now and it's no more arbitrary than late_initcall() itself.
Ideally we'd have some heuristics to detect if we're on an affected
system and tune or skip the delay appropriately, and there may be some
need for a command line option to be added.
Link: https://lore.kernel.org/r/20190904124250.25844-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Cc: stable@vger.kernel.org
There are many regulator consumers who - before using the regulator
bulk functions - set the supply names in regulator_bulk_data using
a for loop.
Let's provide a simple helper in the consumer API that allows users
to do the same with a single function call.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190830071740.4267-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The mt6358 driver was merged in error, it depends on an existing MFD
rather than a newly added one and needs updates to that driver. Disable
the build until those are merged.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MT6358 is a regulator found on boards based on MediaTek MT8183 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1566531931-9772-8-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The differences between SY8824C and SY20278 are different regs
for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163830.2c94f29b@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
The differences between SY8824C and SY20276 are different vsel_min,
vsel_step, vsel_count and regs for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163721.1947f7a0@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
SY8824C is an I2C attached single output regulator made by Silergy Corp,
which is used on several Synaptics berlin platforms to control the
power supply of the ARM cores.
Add a driver for it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163418.1a32fc48@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
In function of_get_child_regulator(), the loop for_each_child_of_node()
contains two mid-loop return statements, each preceded by a statement
putting child. In order to reduce this repetition, create a new label,
err_node_put, that puts child and then returns the required value;
edit the mid-loop return blocks to instead go to this new label.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815053704.32156-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable ret is initialized to a value that is never read before
a return statement and hence can be removed. Remove it.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190813133114.14931-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
_opp_supported_by_regulators() wrongly ignored errors from
regulator_is_supported_voltage(), so it considered errors as
success. Since
commit 4982094451 ("regulator: core: simplify return value on suported_voltage")
regulator_is_supported_voltage() returns a real boolean, so
errors make _opp_supported_by_regulators() return false.
That reveals a problem with the declaration of the VDD1/2
regulators on twl4030.
The VDD1/VDD2 regulators on twl4030 are neither defined with
voltage lists nor with the continuous flag set, so
regulator_is_supported_voltage() returns false and an error
before above mentioned commit (which was considered success)
The result is that after the above mentioned commit cpufreq
does not work properly e.g. dm3730.
[ 2.490997] core: _opp_supported_by_regulators: OPP minuV: 1012500 maxuV: 1012500, not supported by regulator
[ 2.501617] cpu cpu0: _opp_add: OPP not supported by regulators (300000000)
[ 2.509246] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1200000, not supported by regulator
[ 2.519775] cpu cpu0: _opp_add: OPP not supported by regulators (600000000)
[ 2.527313] core: _opp_supported_by_regulators: OPP minuV: 1325000 maxuV: 1325000, not supported by regulator
[ 2.537750] cpu cpu0: _opp_add: OPP not supported by regulators (800000000)
The patch fixes declaration of VDD1/2 regulators by
adding proper voltage lists.
Fixes: 4982094451 ("regulator: core: simplify return value on suported_voltage")
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Link: https://lore.kernel.org/r/20190814214319.24087-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
During reset the VMMC regulator doesn't reach 0V and only drops to
1.8V, furthermore the pulse width is under 200us whereas the SD
specification expect 1ms.
The WR_S bit allows the TWL6030 to no reset at all the VMMC during warm
reset and keep the current voltage. Thanks to this workaround the SD
card doesn't reach a undefined reset stage.
Actually this behavior is available for all the LDO regulator, so the
driver will also allow to use it with any of these regulator.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-4-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It helps to keep sorted order for compatibles, so sort them
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Building without CONFIG_POWER_SUPPLY will fail:
drivers/regulator/act8865-regulator.o: In function `act8865_pmic_probe':
act8865-regulator.c:(.text+0x357): undefined reference to `devm_power_supply_register'
drivers/regulator/act8865-regulator.o: In function `act8600_charger_get_property':
act8865-regulator.c:(.text+0x3f1): undefined reference to `power_supply_get_drvdata'
Add POWER_SUPPLY dependency to Kconfig.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2d09a79bf6 ("regulator: act8865: Add support for act8600 charger")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190807133822.67124-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_gpiod_get_from_of_node() function never returns NULL, it
returns error pointers on error.
Fixes: a867bde3dd ("regulator: slg51000: add slg51000 regulator driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190808103335.GD30506@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804162023.5673-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-38-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The local variable search in regulator_of_get_init_node takes the value
returned by either of_get_child_by_name or of_node_get, both of which
get a node. If this node is not put before returning, it could cause a
memory leak. Hence put search before a mid-loop return statement.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190724083231.10276-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/act8865-regulator.c:447:8-14: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes: 2d09a79bf6 ("regulator: act8865: Add support for act8600 charger")
CC: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20190724092236.witxtfmubun25l2t@1905cc33b6dd
Signed-off-by: Mark Brown <broonie@kernel.org>
The "ti,lp87565" compatible string is still in of_lp87565_match_table,
but current code will return -EINVAL because lp87565->dev_type is unknown.
This was working in earlier kernel versions, so fix it.
Fixes: 7ee63bd747 ("regulator: lp87565: Add 4-phase lp87561 regulator support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190711113517.26077-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting .n_voltages = 1 and .fixed_uV is enough for fixed regulator,
remove the redundant .min_uV and .list_voltage settings.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20190723014102.25103-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This provides a way to monitor battery charge status via the power
supply subsystem.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20190723011418.29143-1-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet http://www.ti.com/lit/ds/symlink/lm36274.pdf:
Table 23. VPOS Bias Register Field Descriptions VPOS[5:0]:
VPOS voltage (50-mV steps): VPOS = 4 V + (Code × 50 mV), 6.5 V max
000000 = 4 V
000001 = 4.05 V
:
011110 = 5.5 V (Default)
:
110010 = 6.5 V
110011 to 111111 map to 6.5 V
So the LM36274_LDO_VSEL_MAX should be 0b110010 (0x32).
The valid selectors are 0 ... LM36274_LDO_VSEL_MAX, n_voltages should be
LM36274_LDO_VSEL_MAX + 1. Similarly, the n_voltages should be
LM36274_BOOST_VSEL_MAX + 1 for LM36274_BOOST.
Fixes: bff5e80715 ("regulator: lm363x: Add support for LM36274")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V
The LM3632_LDO_VSEL_MAX should be 0b101000 (0x28), so the maximum voltage
can match the datasheet.
Fixes: 3a8d1a73a0 ("regulator: add LM363X driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactoring of axp20x driver introduced a bug in AXP803's DCDC6
regulator definition. AXP803_DCDC6_1120mV_STEPS was obtained by
subtracting 0x47 and 0x33. This should be 0x14 (hex) and not 14
(dec).
Refactoring also carried over a bug in DCDC5 regulator definition.
Number of possible voltages must be for 1 bigger than maximum valid
voltage index, because 0 is also valid and it means lowest voltage.
Fixes: 1dbe0ccb06 ("regulator: axp20x-regulator: add support for AXP803")
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20190713090717.347-3-jernej.skrabec@siol.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactoring of the driver introduced bugs in AXP806's DCDCA and DCDCD
regulator definitions.
In DCDCA case, AXP806_DCDCA_1120mV_STEPS was obtained by subtracting
0x47 and 0x33. This should be 0x14 (hex) and not 14 (dec).
In DCDCD case, axp806_dcdcd_ranges[] contains two ranges with same
start and end macros, which is clearly wrong. Second range starts at
1.6V so it should use AXP806_DCDCD_1600mV_[START|END] macros. They are
already defined but unused.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20190713090717.347-2-jernej.skrabec@siol.net
Signed-off-by: Mark Brown <broonie@kernel.org>
- Set 'struct device' fwnode when registering a new device
- New Drivers
- Add support for ROHM BD70528 PMIC
- New Device Support
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
- New Functionality
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
- Fix-ups
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
- Bug Fixes
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera
-----BEGIN PGP SIGNATURE-----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=A3jw
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
A couple of new features in the core, the most interesting one
being support for complex regulator coupling configurations
initially targeted at nVidia Tegra SoCs, and some new drivers but
otherwise quite a quiet release.
- Core support for gradual ramping of voltages for devices that
can't manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jIZwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PG+B/9EQnjM29THpBKM6bKdl8cYcf3Hq/FX
KNtXjwaTM0DqYtpk1RkaHgecxTJwesJ0k9AYijh0ieeMhb5UES280+6B4NqPb7xr
UmFBbNcdk9G+x9q1TyT8akRMkCugEMscQodyk4npzZRjGv8qUsNJUY71Bq2T/JJx
QXo5fKlWICzBahF87DCB5pKC7PKfNkx3BWCrGGXOqoBX2ZEKytyWlCa0nGUZ+LqL
GqXmmIjKL7H8MP3avmrrRHYpeF5DLXAzH+HEIM9Y0F1cRcdgOS1Exv2eG+90a634
yybVDBX2d5zfiEIoRnpldtB52EGXjvwbo7w1mFwh9UgJRbOCZgb+ZQXT
=26r6
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A couple of new features in the core, the most interesting one being
support for complex regulator coupling configurations initially
targeted at nVidia Tegra SoCs, and some new drivers but otherwise
quite a quiet release.
Summary:
- Core support for gradual ramping of voltages for devices that can't
manage large changes in hardware from Bartosz Golaszewski.
- Core support for systems that have complex coupling requirements
best described via code, contributed by Dmitry Osipenko.
- New drivers for Dialog SLG51000, Qualcomm PM8005 and ST
Microelectronics STM32-Booster"
* tag 'regulator-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (52 commits)
regulator: max77650: use vsel_step
regulator: implement selector stepping
regulator: max77650: add MODULE_ALIAS()
regulator: max77620: remove redundant assignment to variable ret
dt-bindings: regulator: add support for the stm32-booster
regulator: add support for the stm32-booster
regulator: s2mps11: Adjust supported buck voltages to real values
regulator: s2mps11: Fix buck7 and buck8 wrong voltages
gpio: Fix return value mismatch of function gpiod_get_from_of_node()
regulator: core: Expose some of core functions needed by couplers
regulator: core: Introduce API for regulators coupling customization
regulator: s2mps11: Add support for disabling S2MPS11 regulators in suspend
regulator: s2mps11: Reduce number of rdev_get_id() calls
regulator: qcom_spmi: Do NULL check for lvs
regulator: qcom_spmi: Fix math of spmi_regulator_set_voltage_time_sel
regulator: da9061/62: Adjust LDO voltage selection minimum value
regulator: s2mps11: Fix ERR_PTR dereference on GPIO lookup failure
regulator: qcom_spmi: add PMS405 SPMI regulator
dt-bindings: qcom_spmi: Document pms405 support
arm64: dts: msm8998-mtp: Add pm8005_s1 regulator
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXRozKAAKCRBiEGxRG/Sl
25okAP9I0Rmscpqjb/+GEeXH4EmL3moGzc9o/BzHRqfeO4wqYAEA+8f7L20xHe8g
tvEGfP7mN/oBmcAfqgH5K9F4eJsBRAw=
=NkCn
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- Add a new LED common module for ti-lmu driver family
- Modify MFD ti-lmu bindings
- add ti,brightness-resolution
- add the ramp up/down property
- Add regulator support for LM36274 driver to lm363x-regulator.c
- New LED class drivers with DT bindings:
- leds-spi-byte
- leds-lm36274
- leds-lm3697 (move the support from MFD to LED subsystem)
- Simplify getting the I2C adapter of a client:
- leds-tca6507
- leds-pca955x
- Convert LED documentation to ReST
* tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
dt: leds-lm36274.txt: fix a broken reference to ti-lmu.txt
docs: leds: convert to ReST
leds: leds-tca6507: simplify getting the adapter of a client
leds: leds-pca955x: simplify getting the adapter of a client
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: max77650: Remove set but not used variable 'parent'
leds: avoid flush_work in atomic context
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
leds: spi-byte: add single byte SPI LED driver
dt-bindings: leds: Add binding for spi-byte LED.
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
Use the new vsel_step field in the regulator description to instruct
the regulator API on the required voltage ramping. Switch to using the
generic regmap helpers for voltage setting and remove the old set_voltage
callback that handcoded the selector stepping.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703161035.31808-3-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators require that the requested voltage be reached gradually
by setting all or some of the intermediate values. Implement a new field
in the regulator description struct that allows users to specify the
number of selectors by which the regulator API should step when ramping
the voltage up/down.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703161035.31808-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Define a MODULE_ALIAS() in the regulator sub-driver for max77650 so that
the appropriate module gets loaded together with the core mfd driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190703084849.9668-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable ret is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190703082009.18779-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
This regulator is supplied by vdda. It's controlled by using SYSCFG:
- STM32H7 has a unique register to set/clear the booster enable bit
- STM32MP1 has separate set and clear registers to configure it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the LP87565_DEVICE_TYPE_LP87561_Q1 case does not have a
break statement, causing it to fall through to a dev_err message.
Fix this by adding in the missing break statement.
Addresses-Coverity: ("Missing break in switch")
Fixes: 7ee63bd747 ("regulator: lp87565: Add 4-phase lp87561 regulator support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the rk809 and rk817 regulator driver.
Their specifications are as follows：
1. The RK809 and RK809 consist of 5 DCDCs, 9 LDOs
and have the same registers for these components except dcdc5.
2. The dcdc5 is a boost dcdc for RK817 and is a buck for RK809.
3. The RK817 has one switch but The Rk809 has two.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Mark Brown <broonie@kernel.org>
[rebased on top of 5.2-rc1]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Split the bd718x7.h to ROHM common and bd718x7 specific parts
so that we do not need to add same things in every new ROHM
PMIC header. Please note that this change requires changes also
in bd718x7 sub-device drivers for regulators and clk.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case the requested gpio property is not found in the device tree, some
callers of gpiod_get_from_of_node() expect a return value of NULL, others
expect -ENOENT.
In particular devm_fwnode_get_index_gpiod_from_child() expects -ENOENT.
Currently it gets a NULL, which breaks the loop that tries all
gpio_suffixes. The result is that a gpio property is not found, even
though it is there.
This patch changes gpiod_get_from_of_node() to return -ENOENT instead
of NULL when the requested gpio property is not found in the device
tree. Additionally it modifies all calling functions to properly
evaluate the return value.
Another approach would be to leave the return value of
gpiod_get_from_of_node() as is and fix the bug in
devm_fwnode_get_index_gpiod_from_child(). Other callers would still need
to be reworked. The effort would be the same as with the chosen solution.
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose some of internal functions that are required for implementation of
customized regulator couplers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Right now regulator core supports only one type of regulators coupling,
the "voltage max-spread" which keeps voltages of coupled regulators in a
given range from each other. A more sophisticated coupling may be required
in practice, one example is the NVIDIA Tegra SoCs which besides the
max-spreading have other restrictions that must be adhered. Introduce API
that allow platforms to provide their own customized coupling algorithms.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supported turning off regulators in suspend only for S2MPS14
device. However this makes also sense for S2MPS11 and can reduce the
power consumption during suspend to RAM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the regulator ID instead of calling rdev_get_id() every time.
This makes code slightly easier to read as shorter 'rdev_id' variable is
used instead of full call. This can also speed things up by reducing
number of calls, although effect was not measured.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Low-voltage switches (lvs) don't have set_points since the voltage ranges
of the output are really controlled by the inputs. This is a problem for
the newly added linear range support in the probe(), as that will cause
a null pointer dereference error on older platforms like msm8974 which
happen to need to control some of the implemented lvs.
Fix this by adding the appropriate null check.
Fixes: 86f4ff7a0c ("regulator: qcom_spmi: enable linear range info")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
spmi_regulator_set_voltage_time_sel() calculates the amount of delay
needed as the result of setting a new voltage. Essentially this is the
absolute difference of the old and new voltages, divided by the slew rate.
The implementation of spmi_regulator_set_voltage_time_sel() is wrong.
It attempts to calculate the difference in voltages by using the
difference in selectors and multiplying by the voltage step between
selectors. This ignores the possibility that the old and new selectors
might be from different ranges, which have different step values. Also,
the difference between the selectors may encapsulate N ranges inbetween,
so a summation of each selector change from old to new would be needed.
Lets avoid all of that complexity, and just get the actual voltage
represented by both the old and new selector, and use those to directly
compute the voltage delta. This is more straight forward, and has the
side benifit of avoiding issues with regulator implementations that don't
have hardware register support to get the current configured range.
Fixes: e92a404741 ("regulator: Add QCOM SPMI regulator driver")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reported-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the DA9061 and DA9062 datasheets the LDO voltage selection
registers have a lower value of 0x02. This applies to voltage registers
VLDO1_A, VLDO2_A, VLDO3_A and VLDO4_A. This linear offset of 0x02 was
previously not observed by the driver, causing the LDO output voltage to
be systematically lower by two steps (= 0.1V).
This patch fixes the minimum linear selector offset by setting it to a
value of 2 and increases the n_voltages by the same amount allowing
voltages in the range 0x02 -> 0.9V to 0x38 -> 3.6V to be correctly
selected. Also fixes an incorrect calculaton for the n_voltages value in
the regulator LDO2.
These fixes effect all LDO regulators for DA9061 and DA9062.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_gpiod_get_from_of_node() call returns ERR_PTR, it is assigned
into an array of GPIO descriptors and used later because such error is
not treated as critical thus it is not propagated back to the probe
function.
All code later expects that such GPIO descriptor is either a NULL or
proper value. This later might lead to dereference of ERR_PTR.
Only devices with S2MPS14 flavor are affected (other do not control
regulators with GPIOs).
Fixes: 1c984942f0 ("regulator: s2mps11: Pass descriptor instead of GPIO number")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMS405 has 5 HFSMPS and 13 LDO regulators,
This commit adds support for one of the 5 HFSMPS regulators (s3) to
the spmi regulator driver.
The PMIC HFSMPS 430 regulators have 8 mV step size and a voltage
control scheme consisting of two 8-bit registers defining a 16-bit
voltage set point in units of millivolts
S3 controls the cpu voltages (s3 is a buck regulator of type HFS430);
it is therefore required so we can enable voltage scaling for safely
running cpufreq.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8005 is used on the msm8998 MTP. The S1 regulator is VDD_GFX, ie
it needs to be on and controlled inorder to use the GPU. Add support to
drive the PM8005 regulators so that we can bring up the GPU on msm8998.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
spmi_regulator_common_get_mode and spmi_regulator_common_set_mode use
multi-level ifs which mirror a switch statement. Refactor to use a switch
statement to make the code flow more clear.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The LP8756x family has a single output 4-phase regulator
configuration. Add support for the same. The control
lies in the master buck which is buck0 for 4-phase
configuration. Enable/disable/voltage set happen via
buck0 registers.
Data Sheet: https://www.ti.com/lit/ds/symlink/lp87561-q1.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The conversion here is really trivial: just a bunch of title
markups and very few puntual changes is enough to make it to
be parsed by Sphinx and generate a nice html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This finalizes the descriptor conversion of the MAX8952 driver
by letting the VID0 and VID1 GPIOs be fetched from descriptors.
Both VID0 and VID1 must be supplied for the VID selection to work,
I add some code to preserve the semantics that if only one of
the two VID gpios is supplied, it will be initialized to low.
This might be a bit overzealous, but I want to preserve any
implicit semantics.
This is currently only used by device tree in-kernel but it is
still also possible to supply the same GPIOs using a machine
descriptor table if a board file is used.
Ideally this should be phased over to using gpio-regulator.c
that does the same thing, but it might require some refactoring
and needs testing on real hardware.
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building with CONFIG_MFD_88PM800 and CONFIG_REGULATOR_88PM800
enabled as loadable modules, we see the following warning:
warning: same module names found:
drivers/regulator/88pm800.ko
drivers/mfd/88pm800.ko
Rework so that the file is named 88pm800-regulator.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the Wolfson Micro WM831x DCDC converter to use
a GPIO descriptor for the GPIO driving the DVS pin.
There is just one (non-DT) machine in the kernel using this, and
that is the Wolfson Micro (now Cirrus) Cragganmore 6410 so we
patch this board to pass a descriptor table and fix up the driver
accordingly.
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just one driver specific fix here, for a boot regression introduced
during some modernization work on the tps6507x driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlz+aOcTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PtiB/96XSSJtLQxArYN2tnTPzeq2asZK3y6
nH1r+d9GAbAj8rIzO9qRSEz/x9oZcikYqR2QdyXSI4pJNH+KRbNpktMTq5HHtm7E
9KNRtz8Ni4dR6Paz04vWA2gUaEps5uMCMDKk38gnL21PLQlaaAn4M0TN/iBBLdgR
8n8tTgPez6gyqtZZ17cwyHAKh4z7Vln5Ps+dyHwLbbzXg0RFwGwRXXIVLFfnGu9E
euBinP6MS3SYvbgnas0+5uXbpGNhXeVPSKnP+muRvTkCs9TxjgV55IUhrWaxXb3+
mrhgElvZ45AwqpQbyQ1+dW7nXQhzFLK6YCVD25BfNe5iq4o1GAjI61CJ
=Dz+r
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Just one driver specific fix here, for a boot regression introduced
during some modernization work on the tps6507x driver"
* tag 'regulator-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps6507x: Fix boot regression due to testing wrong init_data pointer
This driver does not use any symbols from <linux/gpio.h>
no <linux/gpio/consumer.h> so just drop the includes.
Cc: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers are common enough between the LM36274 and the LM363x
series of devices.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published bythe free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190116.345887520@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver does not use any symbols from <linux/gpio.h>
so just drop the include.
Cc: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver does not use any symbols from <linux/gpio.h>
so just drop the include.
Cc: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver uses no symbols from <linux/gpio.h> so just drop
this include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 37 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.724130665@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 83 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.021731668@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 82 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just use a local variable *ena_gpiod in slg51000_of_parse_cb instead.
With this change, the struct slg51000_pdata can be removed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
drivers/regulator/max77650-regulator.c:32:39: warning: tentative
definition of variable with internal linkage has incomplete non-array
type 'struct max77650_regulator_desc'
[-Wtentative-definition-incomplete-type]
static struct max77650_regulator_desc max77651_SBB1_desc;
^
drivers/regulator/max77650-regulator.c:32:15: note: forward declaration
of 'struct max77650_regulator_desc'
static struct max77650_regulator_desc max77651_SBB1_desc;
^
1 warning generated.
Move max77651_SBB1_desc's declaration below max77650_regulator_desc's
definition so this warning does not happen.
Fixes: 3df4235ac4 ("regulator: max77650: Convert MAX77651 SBB1 to pickable linear range")
Link: https://github.com/ClangBuiltLinux/linux/issues/491
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a new driver identity "madera-micsupp" and probe function
so that this driver can be used to control the micsupp regulator on
Cirrus Logic Madera codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a new driver identity "madera-ldo1" and probe function
so that this driver can be used to control the LDO1 regulator on
some Cirrus Logic Madera codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With OF being the only configuration possibility left, depend on it to
simplify some code.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Those definitions are only used within the driver meanwhile, so put them
there.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in-kernel users anymore, so remove this outdated interface.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
A NULL init_data once incremented will lead to oops, fix it.
Fixes: f979c08f76 ("regulator: tps6507x: Convert to regulator core's simplified DT parsing code")
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding regulator driver for the device Dialog SLG51000.
The SLG51000 device contains seven compact and customizable low
dropout regulators and is designed for high performance camera modules
and other small multi-rail applications.
Signed-off-by: Eric Jeong <eric.jeong.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pickable linear range is suitable for The MAX77651 SBB1.
According to MAX77651 TV_SBB1 Code Table:
Use BIT[1:0] as range selectors.
Use BIT[5:2] as selectors for each linear range.
The MAX77651 SBB1 supports up to selector 57, selector 58 ~ 63 are RSVD,
thus set n_voltage to 58.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic is equivalent, but it looks more straightforward this way:
If rdev->desc->ops->enable_time is set, call it.
Otherwise fallback to return rdev->desc->enable_time.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the current clients of this API assume that 0 corresponds
to a failure and non-zero to a pass therefore ignoring the need to
handle a negative error code.
This commit modifies the API to follow that standard since returning a
negative (EINVAL) doesn't seem to provide enough value to justify
the need to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert Dialog Semiconductor DA9xxx regulator drivers to SPDX identifier.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For fixed regulator, setting .n_voltages = 1 and .fixed_uV is enough,
no need to set .min_uV and .list_volage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Slightly better readability by setting fixed_uV instead of min_uV.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables and ab3100_regulator_desc array never need
to be modified, make them const so compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert Powerventure Semiconductor PV88060/PV88080/PV88090 regulator
drivers to SPDX identifier.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The *regdev and *regmap can be replaced by local variables in probe().
Only desc of struct vexpress_regulator is really need, so just use
struct regulator_desc directly and remove struct vexpress_regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the fields in struct sy8106a are only used in sy8106a_i2c_probe(), so
use local variables instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Temporary failures to get a regulator (EPROBE_DEFER) should be logged
as debug information instead of errors.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
